Transcript
TO PLAY MP3 (for remote only) This set can read MP3. 1. Press the FUNCTION button to CD. 2. To open CD door. Place a MP3 disc in the center with the label face front. The total albums and the total tracks appear on the display. 3. Press the PLAY/PAUSE button to start play. 4. Press the STOP button to stop playback. 5. In stop mode, press PLAY/PAUSE button to start playback.
TO SEARCH AN ALBUM Basically this system supports the album search mode to search an album at highspeed. 1. Press the PRESET + / ALBUM + or PRESET – / ALBUM – button to search a desired album in play /stop mode. 2. After selected a desired album, the first track of this album will be shown on the display within two seconds. 3. Press the SKIP/SEARCH / button to search a desired track and then press the PLAY/PAUSE button to play the track. 4. During searching the album, the album number is shown on the display.
SEARCH A FILE (SONGS) BY FILE NAME 1. Press the MP3 MODE button once the " " will blink, the file name and the number's tracks appear on the display. 2. Press the SKIP/SEARCH / buttons one by one to find the file name, the file name will display sequence as "A,B ........... Z, 0 .......... 9". 3. Press the SKIP/SEARCH / buttons about 2 seconds, the capital letters or the figure will blinks. If the first letter of the file name in this disc haven't the capital letters or the figure, it will not blink. / buttons one by one to search file. 4. Press the SKIP/SEARCH 5. Press the PLAY/PAUSE button to play select file.
SEARCH A FILE (SONGS) BY ALBUM 1. Press the MP3 MODE button twice times, the " " will light and ALBUM appear on the display. 2. Press the SKIP/SEARCH / buttons one by one, to select album. 3. Press the SKIP/SEARCH / buttons about 2 seconds until "ALBUM" disappear. 4. Press the SKIP/SEARCH / buttons one by one to search file. 5. Press the PLAY/PAUSE button to play select file.
PROGRAMMING TRACKS - in the MP3 stop mode (Up to a maximum of 64 tracks) 1. 2. 3. 4. 5. 6.
Press the MEM button, the ALBUM blinks on the display. Press the SKIP/SEARCH / buttons to select the desired albums. button, the FILE (SONGS) blinks on the display. Press the MEM Press the SKIP/SEARCH / buttons to select the desired files (songs). button again. Press the MEM Repeat alone step 2 and 5 procedure to program additional tracks. Press PLAY/ PAUSE button to start playback of the programmed tracks and memory indicator will appear on display.
REPEAT PLAY (for remote only) This function will allow a single tracks or all the tracks on the disc to be played repeatedly.
TO REPEAT THE SAME TRACK
TO REPEAT THE WHOLE DISC
Press the REPEAT button once during playback, the repeat one indicator will light.
Press the REPEAT button a second time to repeat all tracks, the repeat all indicator will light.
MICRO MP3 / CD MUSIC SYSTEM OPERATING INSTRUCTIONS
To check the program While in the stop mode, press the MEM button. The album , file (songs) and program numbers will appear on the display. Press the MEM button again to view the other programmed selections. These displays do not appear during programmed play.
TO CANCEL REPEAT PLAY
To play the programmed tracks Press the PLAY/PAUSE
Press the REPEAT button until "REPEAT" indicator is switched off.
button.
To stop programmed play Press the STOP button, if you want to recover programmed play. You can first press button and then press PLAY button again. MEM
To clear the memory content Press the STOP button and then open the CD door or press MEM then press the STOP button in stop mode.
button and
RANDOM PLAY (for remote only) Press the RANDOM button. RANDOM appears in the display and the disc will play automatically.
TO REPEAT PLAY THE ALBUM (in MP3 Mode) (for remote only) Press the REPEAT button three times to repeat the album, the repeat album indicator will light.
CAUTION
All the tracks on the disc can be played in random order.
TO CANCEL RANDOM PLAY Press the STOP or RANDOM button so that "RANDOM" in the display goes out.
TO CANCEL REPEAT PLAY Press the REPEAT button until "REPEAT & ALBUM" indicator is switched off.
RISK OF ELECTRIC SHOCK DO NOT OPEN
The lightning flash and arrowhead within the triangle is a warning sign alerting you of "dangerous voltage" inside the product.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product.
CAUTION : Use of any controls, adjustments, or procedures other than those specified herein may result in hazardous radiation exposure. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION : The apparatus shall not be exposed to rain, moisture, dripping or splashing and the no objects filled with liquids, such as vases, shall be placed on the apparatus.
CLASS 1 LASER PRODUCT CLASS 1 LASER PRODUCT APPAREIL Á LASER DE CLASSE 1
CAUTION
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM
This product contains a low power laser device.
REMOTE CONTROL 1 2 3 4 5 6
10
7 8
11 12 13 14
9
15 16
CARE & MAINTENANCE 1. FM MONO / STEREO / MP3 MODE / CD ESP ON/OFF button 2. STANDBY/ ON button 3. FUNCTION (CD/AUX/TUNER) button 4. PRESET+ / ALBUM+ button STOP / BAND button 5. 6. TUNING / SKIP / SEARCH button button 7. MEMORY 8. PRESET– / ALBUM– button 9. SLEEP button 10. REPEAT button PLAY / PAUSE button 11. 12. TUNING / SKIP / SEARCH button 13. X-BASS button 14. RANDOM button 15. TIMER button 16. VOLUME +\– controls
CLEANING CD If the CD skips or will not play, the disc may need cleaning. Before playing, wipe the disc from the centre out with a cleaning cloth. After playing, store the disc in its case.
CLEANING THE UNIT Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.
IMPORTANT NOTICE: • Should the CD door be opened before the reading of the CD is completed, a jamming noise may occur. This can be resolved by closing the CD door and then setting the FUNCTION switch temporarily to AUX. • If an abnormal display indication or an operating problem occurs, disconnect the AC power cord. Wait at least 5 seconds, then reconnect the AC power cord. • Before transporting the unit, remove the disc from the CD tray.
USING THE REMOTE CONTROL CORRECTLY • Point the Remote Control at the REMOTE SENSOR located on the unit. • When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR may be degraded, causing unreliable operation. • The recommended effective distance for remote operation is about 6 meters (19 feet).
TROUBLE SHOOTING TIPS
1. Open the battery door.
2. Insert one CR2025 (3V) size battery.
ATTENTION Take out the PVC sheet before operating the Remote Control.
CD/MP3
TO CHANGE REMOTE BATTERY
Problem
Solutions
System does not turn on
• Make sure AC power plug is secure in the outlet, and outlet has power. • Make sure FUNCTION switch is set to CD. • Make sure disc label is facing up. • Make sure disc is clean. • Pause mode is activated. • Disc may be damaged or dirty; check disc. • Make sure the unit is on a secure spot. Vibration or jarring can cause the disc to skip.
Disc in place but unit won't play
Disc skips
When battery become weak, the operating distance of the Remote Control is greatly reduced and you will need to replace the battery.
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Poor FM reception
RADIO
WARNING : Do not dispose of batteries in fire, batteries may explode or leak.
Follow the advice below for safe and appropriate operations
ON PLACEMENT
(2) This device must accept any interference received, including interference that may cause undesirable operations.
• Do not use the unit in places which are extremely hot, cold, dusty or humid. • Place the unit on a flat and even surface. • Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by placing it on a carpet. • To avoid magnetized. Do not place the unit near speaker or magnet. • Do not place any naked flame sources, such as lighted candles, on the apparatus. • Do not use this unit in direct sunlight or leave the unit in a closed automobile (or yacht, etc.) where it would be exposed to high temperatures above 40°C. • It also should not be placed in temperatures less than 5°C (41°F) or greater than 35°C (95°F).
ON CONDENSATION
ON SAFETY
The rating plate location is on the bottom of product.
• When connecting and disconnecting the AC cord, grip the plug and not the cord itself. Pulling the cord may damage it and create hazard. • When you are not going to use the unit for a long period of time, disconnect the AC power cord. • When the cord is plugged in, a small amount of current continues to flow to the unit, even when the power is turned off. • When the AC power cord is connected, the standby indicator will light up.
NOTES ON BATTERIES • When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.
• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the CD player. • When there is condensation inside the unit, it may not function normally. • Let it stand for 1 to 2 hours before turning the power on, or gradually heat the room up and dry the unit before use.
VENTILATION WARNING • Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)
RATING PLATE LOCATION Should any trouble occur, disconnect the AC power cord and refer servicing to qualified personnel.
SPECIFICATION GENERAL Power consumption: Output power: Power source:
ON AC VOLTAGE
BATTERY REPLACEMENT NOTE : If the Remote Control is not to be used for a long time, remove the battery to avoid damage caused by battery leakage corrosion.
SAFETY PRECAUTIONS
Poor MW reception
• Make sure FM antenna wire is unwound. • Electrical interference in your home can cause poor reception. Move the unit away from sources of interference (especially those with motors and transformers). • Set the AM/MW loop antenna to a direction for the better reception.
• Before use, check that the rated voltage of your unit matches your local voltage.
FCC INFORMATION This device complies with part 15 of FCC Rules. Operations are subject to the following two conditions: (1) This device may not cause harmful interference, and
65W 30W x 2 (10% THD) AC ~120V 60 Hz (USA and Canada) AC ~220V 50 Hz (China) AC ~230V 50 Hz (Europe) AC ~240V 50 Hz (Australia) AC ~110-120V/220-240V 50/60Hz (Others)
Specifications may be subject to change without notice.
Printed in China
811-6938A1-010
CONNECTIONS
PARTS IDENTIFICATION 1. PHONES jack
4. PLAY / PAUSE 5. VOLUME UP 6. SKIP button
button
/ TUNING UP
9. LCD display STANDBY / ON button
11. STOP 2 3
9
4 5 6 7 8
10 11 12 13 14 15
/ BAND button
12. SLEEP / TIMER button 13. MEMORY
button
14. FUNCTION (CD / AUX / TUNER) button 15. CD door 16. AC cord 17. Speaker terminal
TIMER PLAY AND TURN OFF THE UNIT AUTOMATICALLY
TO TURN OFF THE UNIT Press the STANDBY/ON button to STANDBY, the only clock display will light up.
3 2
button
/ TUNING DOWN
8. SKIP button 10.
LEFT SPEAKER BOX
button
7. VOLUME DOWN
1
RIGHT SPEAKER BOX
TIMER OPERATION
TO TURN ON THE UNIT Press the STANDBY/ON button, the indicator will turn off. Select the desired function and the corresponding function indicator will light up.
1
STANDBY indicator 2. 3. Remote sensor
TURNING ON THE UNIT
indicator will light up and
CLOCK SETTING
4 For external source
5
To AC outlet
1. SPEAKER CONNECTION Remove the rear cover and connect the right speaker to the R terminals, and the left speaker to the L terminals. Connect the wires with the red lines (or printed white lines) to the red (+) terminals and the plain-black wires to the black (–) terminals. NOTE : Connecting speakers other than the speakers supplied with the unit may damage the unit.
R
1. In standby mode, press and hold the MEMORY button for about 3 seconds until time format blinks on display.
4. Press the TUNING / SKIP buttons to set correct hour.
/ 2. Press the TUNING / SKIP buttons to set 12 Hour or 24 Hour time format.
5. Press the MEMORY Minute blinks.
/
L button, the
2. CONNECTION WITH OTHER OPTIONAL EQUIPMENT 6. Press the TUNING / SKIP / buttons to set correct minute, and then press the MEMORY button to start the clock.
To listen to or record audio signals from external units through this unit. Connect the signal cord between the unit's AUX jack and the output jack of the external equipment.
LISTENING TO THE CONNECTED EQUIPMENT • Press the FUNCTION button to AUX. • Play the external source.
3. Press the MEMORY Hour blinks.
20. FM antenna wire Note : 16 to 20 are under the rear cabinet cover.
17 18 19 16
Do not connect to an outside antenna.
TO ADJUST THE VOLUME
FOR PRIVATE LISTENING
The sleep timer is set and the word "SLEEP" is shown on the display. To cancel the sleep timer, press the SLEEP/TIMER button until "SLEEP" go out in the display.
Connect headphones (Ø3.5 mm stereo mini-plug) to the jack. When headphones are connected, PHONES speakers automatically disconnected.
TO SELECT X-BASS (FOR REMOTE ONLY) X-BASS is designed specifically to boost the low frequency sound to obtain a more powerful bass.
NOTE : Press SLEEP/TIMER button to set the sleep timer after 5 seconds. The sleep setting is automatically turned on.
CD PLAYBACK PRESETTING STATION (for remote only)
3. Press the TUNING / SKIP / buttons to select a station.
2. Press the SLEEP/TIMER button one by one to select the length of remaining time until the unit turns off. It changes the indicator in the following way:
Press the VOLUME UP / DOWN button to obtain the desired volume level.
Before use, check that the rated voltage of your unit matches your local voltage. Make sure speakers are connected correctly before plugging the AC power cord into an AC outlet. Caution: • Be sure the AC power cord is disconnected and all functions are off before making connections. • To prevent electrical shock, match wide blade of plug to wide slot, fully insert. (For N. America)
TUNING INTO A STATION MANUALLY 1. Press the FUNCTION button to TUNER.
1. Press the SLEEP/TIMER button while the power is on. "SLEEP 90" lights in the display. Note: SLEEP can be adjusted in TUNER, CD and AUX modes.
ADJUSTING THE SOUND
LISTENING TO THE RADIO
NOTE : 1. To check the TIMER, press the TIMER button twice (for remote only). 2. To cancel the TIMER function, press the TIMER button once (for remote only) and " " will go out in the display.
When the sleep timer is used, the power is automatically turned off after the specified time passes.
5. POWER CORD CONNECTION
20
7. Press the TUNING / SKIP / buttons to set minutes. 8. Press the SLEEP/TIMER button, the "TUNER" will blink on the display. / 9. Press the TUNING / SKIP buttons to set CD or TUNER. 10.Press the SLEEP/TIMER button, the "VOL" will blink on the display. / 11.Press the TUNING / SKIP buttons to set volume. 12.Press the SLEEP/TIMER button to "confirm" and turn on time, turn off time, CD or TUNER, VOL will sequence automatically on display. Finally the " " indicator and clock time will on the display.
SLEEP SETTING
3. MW/AM LOOP ANTENNA CONNECTION Do not connect to an outside antenna. Connect the supplied MW/AM loop antenna to receive better MW/AM broadcast signal.
4. FM ANTENNA WIRE
1. Press and hold SLEEP/TIMER button for about 3 seconds until the " " and "on" indicators will on the display and the hour will blinks on the display. / 2. Press the TUNING / SKIP buttons to set hour. 3. Press the SLEEP/TIMER button, the minute will blink. / 4. Press the TUNING / SKIP buttons to set minutes. Press the SLEEP/TIMER button, the "off" indicator will on the display and the hour will blink on the display. / 5. Press the TUNING / SKIP buttons to set hour. 6. Press the SLEEP/TIMER button, the minute will blink.
button, the
18. AM (MW) loop terminal 19. AUX IN jack
The power can be turn on or turn off automatically at a preset time. So that you can listen CD and RADIO function only. Make sure the clock is correct before TIMER OPERATION. Make sure the time which use to turn on or turn off is correct, please refer to CLOCK setting procedure.
Your favourite Radio Stations can be tuned in to by selecting their preset numbers. It is possible to store up to 10 preset stations for FM band and 10 preset stations for AM/MW band in the order of your choice.
1. Press the FUNCTION button to CD.
3. To start playing, press the PLAY/ PAUSE button.
PROGRAMMING TRACKS - in the CD stop mode (Up to a maximum of 64 tracks) 1. Press the MEM
button.
3. Press the MEM
button again.
Manual memory presetting This feature allows you to manually preset stations to any desired channel. 1. Set to the desired band and station.
STOP/BAND button to 2. Press the select the desired band.
FM
4. Press the MEM the station.
button to memorize
TUNING INTO A PRESET STATION
NOTE: DO NOT CONNECT TO AN OUTSIDE ANTENNA.
TO INTERRUPT PLAYBACK button. Press the PLAY/PAUSE The track time will blink. To resume playback, press the PLAY/ PAUSE button again. TO STOP PLAYBACK button. Press the STOP
xxxx xxxx
2. Press the SKIP / buttons to select the desired tracks.
AM/MW 5. Repeat steps 1 to 4 for the next preset.
Fully unwind the wire antenna. Then extend the wire antenna and place it in the position that sounds best.
2. Open the CD door. Hold the disc by its sides and carefully make it fit onto the central support of compartment with the label side facing towards you until you hear a “click”. The total number and the total time of tracks will show on the display.
x xx xxx xx
2. Press the MEM button until the MEMORY indicator is shown and " 01 " will blink on the display.
FOR BETTER RECEPTION
3. Press the PRESET+/ALBUM+ button to select a channel number for the preset station on the remote control.
Connect the loop aerial (provided) to the "AM (MW) ANT." snap terminal. Set the MW/AM loop antenna to a direction for the better reception.
TO SEARCH FOR A STATION AUTOMATICALLY
TO RECEIVE THE FM BROADCAST IN STEREO
Press the TUNING / SKIP / button for 1 to 2 seconds, and a station is searched for automatically. After tuning in a station, the search stops. The search may not stop at a station with a very weak signal.
When receiving FM broadcasts in stereo, The word " (( STEREO) ) " illuminate.
Press the PRESET+/ALBUM+ or PRESET–/ALBUM– button to select a preset number.
Locating a particular point in a track
Searching for the beginning of a track
To move backward at high speed button pressed Keep the SKIP during play and release at the desired point.
To find a previous track button once to Press the SKIP return to the beginning of the current track. Press the SKIP button repeatedly to skip tracks backward one by one.
To move forward at high speed button pressed Keep the SKIP during play and release at the desired point.
To skip tracks button repeatedly Press the SKIP to skip track(s) forward one by one.
To check the program
To play the programmed tracks
While in the stop mode, press the MEM button. The disc, track and program numbers will appear on the display. Press the MEM button again to view the other programmed selections.
Press the PLAY/PAUSE
These displays do not appear during programmed play.
NOTE: If a button is not pressed within 10 seconds the preset mode will be cancelled automatically.
4. Repeat alone step 2 and 3 procedure to program additional tracks. Press PLAY/PAUSE button to start playback of the programmed tracks and memory indicator will appear on display.
button.
To stop programmed play Press the STOP button, if you want to recover programmed play. You can first press MEM button and then button again. press PLAY
To clear the memory content Keep it pressed
Press it once
NOTE : The CD player may skip if the loud speakers are situated close to the player and if high volume or x-bass levels are used.
Press the STOP button and then open the CD door or press MEM button and then press the STOP button in stop mode.
