Preview only show first 10 pages with watermark. For full document please download

Micron Realssd Nand Flash Solid State Drive (ssd

   EMBED


Share

Transcript

C200 2.5-Inch NAND Flash SSD Features RealSSD™ C200 2.5-Inch SATA NAND Flash SSD MTFDBACxxxMAE Features – Low power consumption (<2.5W active) • Mechanical – Standard SATA connector Voltage: 5V ±5% – Form factor: 2.5-inch drive package (100.45mm x 69.85mm x 9.5mm) – Weight: 77g (MAX) ® • Micron MLC NAND Flash • RoHS-compliant package • Compatibility – Interface: SATA 3 Gb/s – ATA modes supported PIO mode 3, 4 MultiWord DMA mode 0, 1, 2 Ultra DMA mode 0, 1, 2, 3, 4, 5, 6 – Industry-standard 512 byte sector size support – Hot-plug capable – Native command queueing support with 32-command slot support – ATA-7 command set compliant – ATA security feature command set and password login support – Secure erase (data page) command set Fast and Secure erase (clear, sanitize) – Self-monitoring, analysis, and reporting technology (SMART) command set • Performance1, 2 – Sequential READ Up to 170 MB/s – Sequential WRITE Up to 70 MB/s (45 MB/s for 30GB drive) – READ latency 220μs (TYP) – WRITE Latency 370μs (TYP) • Reliability – MTBF (mean time between failures): 1 million device hours – Endurance: total bytes written (TBW) per drive density • 30GB: 21TB • 60GB: 42TB • 120GB: 85TB • 240GB: 171TB – 3 year warranty – Static and dynamic wear leveling – Field-upgradable firmware – Bit error rate: <1 sector per 1015 bits read C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__1.fm - Rev. B 5/09 EN Options • Capacity3 (unformatted) – 30GB – 60GB – 120GB – 240GB • Operating temperature – Industrial (–40°C to +85°C) – Commercial (0°C to +70°C) Notes: 1. Typical I/O performance numbers as measured using Iometer with a queue depth of 32 and write cache enabled. 2. 4K transfers used for READ/WRITE latency values. 3. 1GB = 1 billion bytes; formatted capacity is less. 1 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. Products and specifications discussed herein are subject to change by Micron without notice. C200 2.5-Inch NAND Flash SSD Part Numbering Information Part Numbering Information Micron’s C200 SSD is available in different configurations and densities. Visit www.micron.com for a list of valid part numbers. Figure 1: Part Number Chart MT FD B AC xxx M AE - 1 Micron Technology C 1 IT ES Production Status Blank = Production Product Family ES = Engineering sample FD = Flash drive MS = Mechanical sample Drive Interface Operating Temperature Range B = SATA 3 Gb/s Blank = Commercial (0°C to +70°C) IT = Industrial (–40° to +85°C) Drive Form Factor AA = 1.8-inch Micro SATA HDD replacement (5mm) BOM Revision AC = 2.5-inch HDD replacement (9.5mm) 1 = 1st generation NAND Flash Component Drive Density C = 16Gb, MLC ,x8, 3.3V, 50mm 030 = 30GB 060 = 60GB 120 = 120GB Revision Control 240 = 240GB 1 = 1st generation NAND Flash Type Product Family M = MLC AE = x200 C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__1.fm - Rev. B 5/09 EN 2 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD General Description General Description Micron’s RealSSD solid state drive (SSD) uses a single-chip controller with a SATA 3 Gb/sec interface on the system side and n-channels of Micron NAND Flash internally. Packaged in an HDD replacement enclosure, the SSD integrates easily in existing storage infrastructures. The C200 is designed to use the SATA interface efficiently during both READs and WRITEs while delivering bandwidth focused performance. SSD technology enables enhanced boot times, faster application load times, reduced power consumption, and extended reliability. Figure 2: Functional Block Diagram NAND SATA 3 Gb/s SSD Controller NAND NAND NAND NAND DRAM BUFFER C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN 3 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Architecture Architecture The 200-series SSD is a NAND Flash storage device. A SATA 3 Gb/s interface connects to the SSD externally and communicates with the controller. The controller manages data transfer to and from the NAND Flash array. Table 1: C200 Configurations Unformatted Disk Density NAND Flash Process NAND Flash Density TSOP Package Count Die per TSOP Package 50nm 34nm 50nm 34nm 50nm 34nm 34nm 16Gb 16Gb 16Gb 32Gb 16Gb 32Gb 32Gb 16 16 16 16 16 16 16 1 1 2 1 4 2 4 30GB 60GB 120GB 240GB Logical Block Address Configuration The drive is set to report the number of logical block addresses (LBA) that will ensure sufficient storage space for the specified density. Standard LBA settings based off of the IDEMA standard, LBA1-02, are shown below. Table 2: Standard LBA Settings Drive Size1 30GB 60GB 120GB 240GB Total LBAs Max LBA User Available Bytes Decimal Hexadecimal Decimal Hexadecimal (unformatted) 58,626,288 117,231,408 234,441,648 468,862,128 37E90F0 6FCCF30 DF94BB0 1BF244B0 58,626,287 117,231,407 234,441,647 468,862,127 37E90EF 6FCCF2F DF94BAF 1BF244AF 30,016,659,456 60,022,480,896 120,034,123,776 240,057,409,536 Notes: 1. 1GB = 1,000,000,000 bytes. Table 3: 2.5-Inch Nominal Dimensions and Weight Height Width Length Maximum unit weight C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN 4 Value Unit 9.5 69.85 100.45 77 mm mm mm g Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Architecture Interface Connectors The SATA signal segment interface cable has four conductors and three ground connections. As shown in Figure 3, the cable includes a 7-pin signal segment and a 15-pin power segment arranged in a single row with a 1.27mm (0.050in) pitch. Table 4: Serial ATA Signal Segment Pin Assignments Note: Table 5: Type Description S1 S2 S3 S4 S5 S6 S7 GND A A# GND B# B GND Ground Differential signal pair A and A# Ground Differential signal pair B and B# Ground All pins are in a single row with a 1.27mm (0.050in) pitch. 2.5-Inch SATA Power Segment Pin Assignments Note: Figure 3: Signal Name Pin# Signal Name P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 V33 V33 V33 GND GND GND V5 V5 V5 GND DAS1 GND V12 V12 V12 Description No connect No connect No connect Ground Ground Ground 5V power, precharge 5V power 5V power Ground Device Activity Signal Ground No connect No connect No connect 1. The DAS signal may be optionally connected to GND if an LED is not being used. Interface Connections C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN 5 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Device ID Device ID Table 6: IDENTIFY Device ID F = The content of the word is fixed and does not change V = The content of the word is variable and may change depending on the state of the device or the commands excuted by the device X = The content of the word may be fixed or variable R = The content of the word is reserved and shall be zero Word Bit(s) Setting Default Value 0 15 14-8 7 6-3 2 1 0 15-0 15-0 15-0 31-0 15-0 31-0 15-0 159-0 47-0 63-0 319-0 15-8 7-0 F X F X V X F X V X X X V X F X F F F F 0b X 0b X 0/1b X 0b X X X X X X X Varies X Varies Varies 80h 10h 15-0 15-14 13 F R F 0h 00b 1b 12 11 R F 0b 1b 10 9 8 7-0 15 14 13-2 1 0 31-0 F F F X F F F X F X 1b 1b 1b X 0b 1b 0h X 0b X 1 2 3 4-5 6 7-8 9 10-19 20-22 23-26 27-46 47 48 49 50 51-52 C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN Description 0 = ATA device Retired 0 = Non-removable media device Don’t Care 1 = IDENTIFY DEVICE data incomplete Retired Reserved Number of logical cylinders (obsolete) Specific configuration (obsolete) Number of logical heads (obsolete) Number of logical sectors per logical track (obsolete) Reserved Reserved Retired Serial number (20 ASCII characters) Don’t Care Firmware revision (8 ASCII characters) Model number (40 ASCII characters) 80h 00h = Reserved 01h-FFh = Number of sectors transfered per interrupt on R/W MULTIPLE cmds Reserved Reserved for IDENTIFY PACKET DEVICE cmd 1 = Standby timer values as specified in ATA/ATAPI - 7 support 0 = Standby timer values shall be managed by the device Reserved for IDENTIFY PACKET DEVICE cmd 1 = IORDY support 0 = IORDY may be supported 1 = IORDY may be disabled 1 = LBA support 1 = DMA support Retired Shall be cleared to 0 Don’t Care (set to 1) Reserved Obsolete 1 = Device specific standby timer min value Obsolete 6 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Device ID Table 6: IDENTIFY Device ID (Continued) F = The content of the word is fixed and does not change V = The content of the word is variable and may change depending on the state of the device or the commands excuted by the device X = The content of the word may be fixed or variable R = The content of the word is reserved and shall be zero Word Bit(s) Setting Default Value 53 15-3 2 R F 0h 1b 1 F 1b 0 15-0 15-0 15-0 31-0 15-9 8 7-0 X X X X X F V V X X X X X 0h X X 31-0 15-0 15-11 10 F X F V Sect X 0h 0/1b 9 V 0/1b 8 V 0/1b 65 7-3 2 1 0 15-2 1-0 15-0 F F F F F F F 0h 1b 1b 1b 0h 3h 78h 66 15-0 F 78h 67 68 69-74 75 15-0 15-0 95-0 15-5 4-0 F F F F F 78h 78h 0h 0h 1Fh 54 55 56 57-58 59 60-61 62 63 64 C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN Description Reserved 1 = The fields reported in word 88 are valid 0 = The fields reported in word 88 are not valid 1 = The fields reported in words (70:64) are valid 0 = The fields reported in words (70:64) are not valid Obsolete Number of current cylinders (obsolete) Number of current heads (obsolete) Numer of current sectors per track (obsolete) Current capacity in sectors (obsolete Reserved 1 = Multiple sector setting is valid (Don’t Care) xxh = Current setting for number of sectors per interrupt on R/W MULTIPLE cmds Total number of user addressable sectors (28-bit address) Obsolete Reserved 1 = Multiword DMA mode 2 is selected 0 = Multiword DMA mode 2 is not selected 1 = Multiword DMA mode 1 is selected 0 = Multiword DMA mode 1 is not selected 1 = Multiword DMA mode 0 is selected 0 = Multiword DMA mode 0 is not selected Reserved 1 = Multiword DMA mode 2 and below is supported 1 = Multiword DMA mode 1 and below is supported 1 = Multiword DMA mode 0 is supported Reserved PIO modes support Minimum multiword DMA transfer cycle time per word in nanoseconds MFR recommended multiword DMA transfer cycle time per word in nanoseconds Minimum PIO transfer cycle time without IORDY flow control Minimum PIO transfer cycle time with IORDY flow control Reserved Reserved 1Fh = NCQ device (1Fh = 32 - 1 (maximum queue depth support)) 7 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Device ID Table 6: IDENTIFY Device ID (Continued) F = The content of the word is fixed and does not change V = The content of the word is variable and may change depending on the state of the device or the commands excuted by the device X = The content of the word may be fixed or variable R = The content of the word is reserved and shall be zero Word Bit(s) Setting Default Value 76 15-13 12 11 10 9 F F F F F 0h 0b 0b 0b 0b 8 7-3 2 1 0 15-0 15-7 6 5 4 3 F F F F F F F F F F F 1b 0h 1b 1b 0b 0h 0h 1b 0b 0b 1b 2 1 0 15-7 6 5 4 3 2 1 0 15-9 8 7 6 5 4 3-1 0 15-0 F F F F V F V V V V F F F F F F F X F F 0b 0b 0b 0h 1b 0b 0b 0b 0b 0b 0b 0h 0b 1b 1b 1b 1b X 0b 21h 77 78 79 80 81 C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN Description Reserved 1 = Supports NCQ priority information 1 = Supports unload while NCQ commands outstanding 1 = Supports phy event counters 1 = Supports receipt of host-initiated power management requests (HIPM) 1 = Supports native command queuing (NCQ) Reserved 1 = Supports Serial ATA Gen-2 signaling speed (3 Gb/s) 1 = Supports Serial ATA Gen-1 signaling speed (1.5Gb/s) Reserved Reserved Reserved 1 = Supports software settings preservation Reserved 1 = Supports in-order data delivery 1 = Device supports initiating interface power management (DIPM) 1 = Supports DMA Setup auto-activate optimization 1 = Supports nonzero buffer offsets in DMA Setup FIS Reserved Reserved 1 = Software settings preservation enabled Reserved 1 = In-order data delivery enabled 1 = Device initiating interface power management enabled 1 = DMA setup auto-activate optimization enabled 1 = Nonzero buffer offsets in DMA setup FIS enabled Reserved Major version number reserved (future revisions) Reserved for ATA/ATAPI-8 major version number 1 = Supports ATA/ATAPI-7 major version number 1 = Supports ATA/ATAPI-6 major version number 1 = Supports ATA/ATAPI-5 major version number 1 = Supports ATA/ATAPI-4 major version number Obsolete Reserved Minor version number 8 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Device ID Table 6: IDENTIFY Device ID (Continued) F = The content of the word is fixed and does not change V = The content of the word is variable and may change depending on the state of the device or the commands excuted by the device X = The content of the word may be fixed or variable R = The content of the word is reserved and shall be zero Word Bit(s) Setting Default Value 82 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 X F F F X F F F F F F F F F F F F F F F F F F F F F X 1b 1b 1b X 1b 0b 0b 0b 1b 1b 0b 1b 0b 1b 1b 0b 1b 1b 1b 1b 1b 0b 1b 0b X 5 4 3 2 1 0 F F F F F F 1b 0b X 0b 0b 1b 83 C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN Description Obsolete 1 = NOP command support 1 = READ BUFFER command support 1 = WRITE BUFFER command support Obsolete 1 = Host-protected area feature set support 1 = DEVICE RESET command support (ATAPI packet command) 1 = Service interrupt support 1 = Release interrupt support 1 = Look-ahead support 1 = Write cache support 1 = Packet command feature set support 1 = Mandatory Power management feature set support 1 = Removable media feature set support 1 = Security mode feature set support 1 = SMART feature set support Shall be cleared to 0 Shall be set to 1 1 = FLUSH CACHE EXT command support 1 = Mandatory FLUSH CACHE command support 1 = Device configuration overlay feature set support 1 = 48-bit address feature set support 1 = Automatic acoustic management feature set support 1 = SET MAX security extension support 1 = Address offset reserved area boot mode support 1 = SET FEATURES subcommand required by HDD will be non-op to an SSD 1 = Power-up in standby feature set support 1 = Removable media status notification feature set support 1 = Advanced power management feature set support 1 = CFA feature set support 1 = READ/WRITE DMA QUEUED support 1 = DOWNLOAD MICROCODE command support 9 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Device ID Table 6: IDENTIFY Device ID (Continued) F = The content of the word is fixed and does not change V = The content of the word is variable and may change depending on the state of the device or the commands excuted by the device X = The content of the word may be fixed or variable R = The content of the word is reserved and shall be zero Word Bit(s) Setting Default Value 84 15 14 13 12 11 10 F F F F F F 0b 1b 0b X X 0b 9 F 0b 8 7 6 F F F X 0b 1b 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 F F F F F F X F F F X V F V V V V F F F V V 1b 0b 0b 0b 1b 1b X 1b 1b 1b X 1b 0b 0b 0b 1b 1b 0b 1b 0b 0b 1b 85 C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN Description Shall be cleared to 0 Shall be set to 1 1 = IDLE IMMEDIATE with UNLOAD FEATURE support Reserved for technical report INCITS TR-37-2004 (TLC) Reserved for technical report INCITS TR-37-2004 (TLC) 1 = URG bit support for WRITE STREAM DMA EXT and WRITE STREAM EXT 1 = URG bit support for READ STREAM DMA EXT and READ STREAM EXT 1 = 64-bit world wide name support 1 = WRITE DMA QUEUED FUA EXT command support 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands support 1 = General purpose logging feature set support 1 = Streaming feature set support 1 = Media card passthrough command feature set support 1 = Media serial number support 1 = SMART self-test support 1 = SMART error logging support Obsolete 1 = NOP command enabled 1 = READ BUFFER command enabled 1 = WRITE BUFFER command enabled Obsolete 1 = Host-protected area feature set enabled 1 = DEVICE RESET command enabled (ATAPI packet command) 1 = SERVICE interrupt enabled 1 = release interrupt enabled 1 = look-ahead enabled 1 = write cache enabled 1 = Packet command feature set enabled 1 = Power management feature set enabled 1 = Removable media feature set enabled 1 = Security mode feature set enabled 1 = SMART feature set enabled 10 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Device ID Table 6: IDENTIFY Device ID (Continued) F = The content of the word is fixed and does not change V = The content of the word is variable and may change depending on the state of the device or the commands excuted by the device X = The content of the word may be fixed or variable R = The content of the word is reserved and shall be zero Word Bit(s) Setting Default Value 86 15 14 13 12 11 10 9 8 F F F F F F V F 1b 0b 1b 1b 1b 1b 0b 0b 7 6 F F 0b X 5 4 3 2 1 0 15 14 13 12 11 10 V V V F F F F F F F F F 0b 0b 0b 0b 0b 1b 0b 1b 0b X X 0b 9 F 0b 8 7 6 F F F X 0b 1b 5 4 3 F V V 1b 0b 0b 2 1 0 V F F 0b 1b 1b 87 C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN Description 1 = Words 120 and 119 are valid Reserved 1 = FLUSH CACHE EXT command supported 1 = Mandatory FLUSH CACHE command support 1 = Device configuration overlay feature set support 1 = 48-bit address feature set support 1 = Automatic acoustic management feature set enabled 1 = SET MAX security extension enabled by SET MAX SET PASSWORD 1 = Address offset reserved area boot mode active 1 = SET FEATURES subcommand required on HDD and is Non-Op for an SSD 1 = Power-up in standby feature set enabled 1 = Removable media status notification feature set enabled 1 = Advanced power management feature set enabled 1 = CFA feature set enabled 1 = READ/WRITE DMA QUEUED support 1 = DOWNLOAD MICROCODE command support Shall be cleared to 0 Shall be set to 1 1 = IDLE IMMEDIATE with UNLOAD FEATURE support (default) Reserved for technical report INCITS TR-37-2004 (TLC) Reserved for technical report INCITS TR-37-2004 (TLC) 1 = URG bit for WRITE STREAM DMA EXT & WRITE STREAM EXT (sup. Dflt.) 1 = URG bit for READ STREAM DMA EXT & READ STREAM EXT (sup. Dflt.) 1 = 64-bit world wide name support (default) 1 = WRITE DMA QUEUED FUA EXT command support (default) 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT cmds support (default) 1 = General purpose logging feature set support (default) 1 = Streaming feature set support (default) 1 = Media card passthrough command feature set support (default) 1 = Media serial number support (default) 1 = SMART self-test support (default) 1 = SMART error logging support (default) 11 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Device ID Table 6: IDENTIFY Device ID (Continued) F = The content of the word is fixed and does not change V = The content of the word is variable and may change depending on the state of the device or the commands excuted by the device X = The content of the word may be fixed or variable R = The content of the word is reserved and shall be zero Word Bit(s) Setting Default Value 88 15 14 13 F F V 0b 0b 0/1b 12 V 0/1b 11 V 0/1b 10 V 0/1b 9 V 0/1b 8 V 0/1b 7 6 5 4 3 2 1 0 15-0 15-0 15-0 15-0 15-0 15-8 7-0 79-0 63-0 367-0 15-0 15-9 8 7-6 5 4 3 2 1 0 F F F F F F F F F F V V V V V F V F F F V R V V V V V F 0b X 1b 1b 1b 1b 1b 1b 5h 5h 0h 0h or FFFFh 0h X 0h X LBA X 0h X X X 0b X X X X 1h 89 90 91 92 93 94 95-99 100-103 104-126 127 128 C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN Description Reserved Reserved 1 = Ultra DMA mode 5 is selected 0 = Ultra DMA mode 5 is not selected 1 = Ultra DMA mode 4 is selected 0 = Ultra DMA mode 4 is not selected 1 = Ultra DMA mode 3 is selected 0 = Ultra DMA mode 3 is not selected 1 = Ultra DMA mode 2 is selected 0 = Ultra DMA mode 2 is not selected 1 = Ultra DMA mode 1 is selected 0 = Ultra DMA mode 1 is not selected 1 = Ultra DMA mode 0 is selected 0 = Ultra DMA mode 0 is not selected Reserved 1 = Ultra DMA mode 6 and below supported 1 = Ultra DMA mode 5 and below supported 1 = Ultra DMA mode 4 and below supported 1 = Ultra DMA mode 3 and below supported 1 = Ultra DMA mode 2 and below supported 1 = Ultra DMA mode 1 and below supported 1 = Ultra DMA mode 0 support Time required; Security erase unit complete Time required; Enhanced security erase complete Current advanced power management value Master password revision code Cleared to 0s if Serial ATA Vendor's recommended acoustic management value Current auto acoustic management value Reserved Maximum user LBA for 48-bit address feature set Reserved Removable media bits Security status bits 1 = Security mode enabled Security status bits 1 = Enhanced security erase unit support 1 = Security count is expired 1 = Security frozen 1 = Security locked 1 = Security enabled 1 = Security supported 12 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Device ID Table 6: IDENTIFY Device ID (Continued) F = The content of the word is fixed and does not change V = The content of the word is variable and may change depending on the state of the device or the commands excuted by the device X = The content of the word may be fixed or variable R = The content of the word is reserved and shall be zero Word Bit(s) Setting Default Value 129-254 255 2015-0 15-8 7-0 F X X X X A5h C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN Description Reserved Checksum A5h = signature for ATA device 13 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Commands Commands Table 7: Supported ATA Command Set See ATA-7 standard for command details Command Name Command Code (hex) 98h or E5h B1h / C0h B1h / C1h B1h / C2h B1h / C3h 92h 90h E7h EAh ECh E3h or 97h E1h or 95h 91h 00h E4h C8h C9h 25h 60h 2Fh C4h 29h F8h 27h 24h 20h 21h 42h 40h F6h F3h F4h F5h F1h F2h 7xh EFh F9h F9h / 04h F9h / 02h 37h C6h CHECK POWER MODE DEVICE CONFIGURATION RESTORE DEVICE CONFIGURATION FREEZE LOCK DEVICE CONFIGURATION IDENTIFY DEVICE CONFIGURATION SET DOWNLOAD MICROCODE EXECUTE DEVICE DIAGNOSTIC FLUSH CACHE FLUSH CACHE EXT IDENTIFY DEVICE IDLE IDLE IMMEDIATE INITIALIZE DEVICE PARAMETERS NOP READ BUFFER READ DMA (with retry) READ DMA (without retry) READ DMA EXT READ FPDMA QUEUED READ LOG EXT READ MULTIPLE READ MULTIPLE EXT READ NATIVE MAX ADDRESS READ NATIVE MAX ADDRESS EXT READ SECTOR(S)EXT READ SECTOR(S) (with retry) READ SECTOR(S) (without retry) READ VERIFY SECTOR EXT READ VERIFY SECTOR(S) (with retry) SECURITY DISABLE PASSWORD SECURITY ERASE PREPARE SECURITY ERASE UNIT SECURITY FREEZE LOCK SECURITY SET PASSWORD SECURITY UNLOCK SEEK SET FEATURES SET MAX ADDRESS SET MAX – FREEZE LOCK SET MAX – LOCK SET MAX ADDRESS EXT SET MULTIPLE MODE C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN 14 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Commands Table 7: Supported ATA Command Set (Continued) See ATA-7 standard for command details Command Name Command Code (hex) F9h / 01h F9h / 03h E6h or 99h B0h / D9h B0h / D8h B0h / D2h B0h / D4h B0h / D0h B0h / D5h B0h / DAh B0h / D6h E2h or 96h E0h or 94h E8h CAh CBh 35h 3Dh 61h 3Fh C5h 39h CEh 30h 34h SET MAX – SET PASSWORD SET MAX – UNLOCK SLEEP SMART DISABLE OPERATIONS SMART ENABLE OPERATIONS SMART ENABLE/DISABLE AUTOSAVE SMART EXECUTE OFF-LINE IMMEDIATE SMART READ DATA SMART READ LOG SECTOR SMART RETURN STATUS SMART WRITE LOG STANDBY STANDBY IMMEDIATE WRITE BUFFER WRITE DMA (with retry) WRITE DMA (without retry) WRITE DMA EXT WRITE DMA FUA EXT WRITE FPDMA Queued WRITE LOG EXT WRITE MULTIPLE WRITE MULTIPLE EXT WRITE MULTIPLE FUA EXT WRITE SECTOR(S) (with retry) WRITE SECTOR(S) EXT C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN 15 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Reliability Reliability Micron’s SSDs incorporate advanced technology for defect and error management. They use various combinations of hardware-based error correction algorithms and firmwarebased static and dynamic wear-leveling algorithms. Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is defined as data that is reported as successfully programmed to the SSD but when it is read out of the SSD, the data differs from what was programmed. See Table 8 for the uncorrectable bit error rate for the SSD. Table 8: Uncorrectable Bit Error Rate Uncorrectable Bit-Error Rate Operation 1015 READ <1 sector per bits read Mean Time Between Failures Mean time between failures (MTBF) for the SSD can be predicted based on the component reliability data using the methods referenced in the Telcordia SR-332 reliability prediction procedures for electronic equipment. The table below shows the MTBF for each SSD density. Table 9: Mean Time Between Failures Density MTBF (Operating Hours) 1 million 1 million 1 million 1 million 30GB 60GB 120GB 240GB Endurance Endurance for the SSD can be predicted based on the usage conditons applied to the device, the internal NAND component cycles, the write amplification factor, and the wear-leveling efficenty of the drive. The table below shows the drive lifetime for each SSD density based on predefined usage conditions. Table 10: Drive Lifetime Density Drive Lifetime (Total Bytes Written) 21 TB 42 TB 85 TB 171 TB 30GB 60GB 120GB 240GB Notes: 1. TBW calculated with the drive 90% full. 2. Access pattern consist of the following: 5% are 4k, 5%are 8k, 10% are 16k, 10% are 32k, 35% are 64K, and 35% are 128k. 3. GB/day can be calculated by dividing the TBW value by (365 * # of years). C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN 16 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Electrical Characteristics Electrical Characteristics Table 11: SSD Serial ATA Typical Power Consumption1 Density Idle3 Sleep3 Standby3 Erase Read2 Write2 Unit 30GB 60GB 120GB 240GB 0.116 0.116 0.116 0.116 0.116 0.116 0.116 0.116 0.116 0.116 0.116 0.116 2.5 2.5 2.5 2.5 1.6 1.6 1.6 1.6 2.5 2.5 2.5 2.5 W W W W Notes: 1. Data taken at 25°C. 2. IOMETER MAX transfer rate with 128KB transfer size. 3. DIPM enabled. Table 12: Absolute Maximum Ratings Parameter/Condition Voltage input Operating temperature Symbol Min Max Unit V5 TA 4.75 0 –40 –55 – 5 +5.25 70 +85 +95 +20 95 V °C °C °C °C/hour % Commercial Industrial Non-operating temperature Rate of temperature change Relative humidity (noncondensing) Stresses greater than those listed in Table 12 may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Table 13: Shock and Vibration Parameter/Condition Specification 1500 G/1.0ms 2–500Hz at 3.1G Operating shock Operating vibration Table 14: Recommended Operating Conditions Parameter/Condition Symbol Min Typ Max Unit Power supply voltage Ground supply voltage V5 GND 4.75 0 5.00 0 5.25 0 V V C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN 17 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Compliance Compliance Micron SSDs comply with the following: • RoHS “green” package • CE (Europe): EN55022, 2006 Class B and EN55024, 1998 + A1: 2001 + A2:2003 • FCC: CFR Title 47, Part 15, ICES-003, all Class B • UL (US): approval to UL-60950-1, 2nd Edition, 2007-03-27, IEC 60950-1:2005, 2nd Edition • BSMI (Taiwan): Appproval to CNS 13438 • TUV/GS (Germany): Approval to IEC60950 / EN6095 • VCCI • W.E.E.E. C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN 18 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD Package Dimensions Package Dimensions Figure 4: 2.5-Inch Package (Preliminary) 69.85 ±0.25 2.750 in ±0.010 61.72 2.430 in 4.07 B TM SIDE 0.160 in BTM SIDE D&T M3X0.5 (4 PLCS) BTM SIDE 1.5 2 0.060 in 3. 5 0 ± 0 . 3 8 0.138 in ±0.015 0.25 0.010 in TYP CON CLEARANCE DETAIL B 100.45 3.955 in 90.60 3.567 in BTM SIDE 13.43 0.529 in 9.50 +-00..5000 0.374 in 14.00 0.551 in BTM SIDE 3.0 0.12 in RAD (4 PLCS) +0.000 -0.020 B 0.30 0.012 in 14.00 0.551 in BOTH SIDES 90.60 3.567 in BOTH SIDES 3.00 0.118 in BOTH SIDES Note: 4.75 0. 187 i n D&T M3X0.5 (2 PLCS) BOTH SIDES All dimensions are in millimeters. 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900 [email protected] www.micron.com Customer Comment Line: 800-932-4992 Micron, the M logo, the Micron logo, and RealSSD are trademarks of Micron Technology, Inc. All other trademarks are the property of their respective owners. This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein. Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur. C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive__2.fm - Rev. B 5/09 EN 19 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved. C200 2.5-Inch NAND Flash SSD References References The following references were used to prepare this data sheet: • Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available at www.sata-io.org • Small Form Factor Specification SFF-8201, SFF-8223. • Electronic Industries Association Standard, EIA-720 • Serial ATA: High-speed serialized AT attachment, Serial ATA working group • SFF documents • EIA-720 document Table 15: Terminology Acronym Definition ATA IOPS PIO SATA SSD (U)DMA SFF Advanced technology attachment Input/output operations per second Programmed input/output data transfer mode Serial advanced technology attachment Solid state drive (Ultra) direct memory access data transfer mode Small form factor C200 2.5" PDF: 09005aef836873c9 / Source: 09005aef82cb3c5e realssd_flash_drive_app a_refs__x.fm - Rev. B 5/09 EN 20 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2007 Micron Technology, Inc. All rights reserved.