Transcript
MicroPar TRI 6 6x3W 3in1 LEDs (RGB)
USER MANUAL
Table of Contents
1. Introduction ................................................................................................. 1 2. Safety ............................................................................................................ 2 3. DMX Values & Functions .............................................................................. 3 4. Display Operation ......................................................................................... 5 5. Menu Guide & Operation .............................................................................. 6 6. DMX Connections ......................................................................................... 9 7. Master/Slave Mode Operation .................................................................... 10 8. Troubleshooting .......................................................................................... 10 9. Technical Information.....…..……………………….…………………………...11
1. Introduction
Ø Summary Thank you for purchasing the ColorKey MicroPar TRI 6. Please read these instructions carefully before use. Operating this fixture according to these instructions is important to avoid any possible damage or accidents caused by misuse.
Ø Product Introduction The ColorKey MicroPar TRI 6 uses a MicroPar cast aluminum housing and adopts 6 high-powered 3-in-1 LEDs. Each LED is made up of Red, Green, and Blue LEDs. This fixture features long life span, low power consumption, amazing color mixing and bright output. Each of the 3 colors can be independently controlled. Built-in modes include; dimming, strobe, gradual change, color fading, color pulse as well as other programs. This fixture uses a switching power supply that is lightweight and requires minimal power consumption. This fixture also features universal protocol DMX-512.
Ø Packing list n
1x MicroPar TRI 6
n
User Manual
n
Warranty Card
1
2. Safety
Ø Safety Notes Caution! Opening this unit voids warranty. Contact ColorKey for any service requests. Warning! To avoid electrical shock, be sure to disconnect power before any service or when moving or setting up the fixture. Caution! Avoid direct eye exposure with the fixture when on.
Ø
Safety Instruction
● The MicroPar TRI 6 has an automatic voltage switch and will automatically detect voltage when connected to power. Please be sure to check voltage is within the range of this fixture’s specifications. ● Before use, check this fixture for damage that may have been caused during the shipping process. Do not use and contact ColorKey immediately should you notice any damage. ● This fixture is designed for indoor use only; operating this fixture outdoors may cause damage. ● This fixtures maybe mounted in any position provided there is adequate space for ventilation.
2
3. DMX Values & Functions
Ø DMX 3 Channel Mode Channel Value CH1 000-255 CH2 000-255 CH3 000-255
Ø DMX 6 Channel Mode Channel Value CH1
000-255
CH2
000-255
CH3
000-255
CH4
000-255
CH5
CH6
000-014 015-255 000-031 032-063 064-095 096-127 128-159 160-191 192-223 224-255
Function Red 0-100% Green 0-100% Blue 0-100%
Notes
Function Master Dimmer 0-100% Red 0-100% Green 0-100% Blue 0-100% Dimming Strobe (Fast-Slow)
Notes
N/A Dark - Bright Bright – Dark Dark-Bright-Dark Fade
Not Used Use Ch 1-4 to activate. Channel 5 becomes speed adjustment.
Dark-Bright-Dark (Auto) Color Flash Sound Activated
Channel 5 becomes speed adjustment.
3
Priority
1
2
3
Ø DMX 7/8 Channel Mode Channel Value Function CH1 000-255 Master Dimmer 0-100% CH2 000-255 Red 0-100% CH3 000-255 Green 0-100% CH4 000-255 Blue 0-100% 000-014 Dimming CH5 015-255 Strobe Speed (Fast-Slow) 000-031 N/A 032-063 Dark-Bright 064-095 Bright-Dark 096-127 Dark—Bright—Dark CH6 128-159 Color Fade 160-191 Dark-Bright-Dark (Auto) 192-223 Color Flash 224-255 Sound Activated 000-009 N/A 010-029 R 100% 030-039 R 85%+Y 15% 040-049 R 60%+Y 40% 050-069 Y 100% 070-079 Y 85%+G 15% 080-089 Y 60%+G 40% 090-109 G 100% 110-119 G 85%+B 15% CH7 120-129 G 60%+B 40% 130-149 B 100% 150-159 B 85%+C 15% 160-169 B 60%+C 40% 170-189 C 100% 190-199 C 50%+P 50% 200-219 P 100% 220-229 P 50%+W 50% 230-249 W 95%+Y 5% 250-255 W 100% 000-005 Use ‘nodE’ setting 006-055 Dimming 0 056-105 Dimming 1 CH8 106-155 Dimming 2 156-205 Dimming 3 205-255 Dimming 4
4
Notes
Priority 1
3 Not used Use CH. 1-4 to activate Ch. 5 becomes speed adjustment.
3
Ch. 5 becomes speed adjustment.
2
1
4. Display Operation
Ø MENU: Access the menu/Scroll through menu options Ø ENTER: Open/Select the current menu option Ø UP: Scroll through menu selection or parameter increase Ø DOWN: Scroll through menu selection or parameters decrease
5
5. Menu Guide & Operation Addr
d001-d512
DMX Mode
UErn
UE2.0
nodE
nod0-nod4
Speed Limiter
LEd
on/oFF
Display On/Off
SoUA
SO.UA
bL- -
b000-b255
Blue Dimming
GL
G000-G255
Green Dimming
rL--
r000-r255
FLAS
FL00-FL15
FAdE
FA00-FA15
ASC
AC00-AC15
Pr- -
Pr00-Pr15
Software Version
Sound Activated Mode
MENU
6
Red Dimmer
Strobe Mode (Fast-Slow) Color Fade (Fast-Slow)
Color Change
Preset Selection
SP- -
SP00-SP15
Program Speed
SLAU
SL.AU
Slave Mode
CHnd
3/6/7/8
DMX Channel Mode
1．Operating instruction: To operate your unit in DMX mode, follow these steps: Ø Press MENU to activate display / return to ‘main menu’ screen. Ø Press UP/DOWN until “Addr” is displayed. Ø Press ENTER to proceed. Display will flash indicating you have entered edit mode. Ø Press UP/DOWN to select desired DMX address. This will display as d001-d512. Ø Press ENTER to save and store your selections. The screen will stop flashing indicating you have exited edit mode. To select DMX Channel Mode, follow these steps: Ø Press MENU to activate display / return to ‘main menu’ screen. Ø Press UP/DOWN until “CHnd” is displayed. Ø Press ENTER to proceed. Display will flash to indicating you have entered edit mode. Ø Press UP/DOWN to select desired DMX channel mode (3CH, 6CH, 10CH or 11CH). Ø Press ENTER to save and store your selections. The screen will stop flashing indicating you have exited edit mode. To select Display On/Off, follow these steps: Ø Press MENU to activate display / return to ‘main menu’ screen. Ø Press UP/DOWN until “LED” is displayed. Ø Press ENTER to proceed. Display will flash indicating you have entered edit mode. Ø Press UP/DOWN until desired selection is displayed (“On” or “OFF”). Ø Press ENTER to save and store your selections. The screen will stop flashing indicating you have exited edit mode.
7
Note*** Display will remain on for approximately 2 minutes after the last button selection. When the display is off, press any button to activate display. 2. Details of Built-in Programs (Pr- -) Ø Press MENU to activate display / return to ‘main menu’ screen. Ø Press UP / DOWN until “Pr- -“ is displayed. Ø Press ENTER to proceed. Display will flash indicating you have entered edit mode. Ø Press UP / DOWN until desired selection is displayed (see chart below “Pr- -“). Ø Press ENTER to save and store your selections. The screen will stop flashing indicating you have exited edit mode. Built-in Program Chart: Ø Pr32 - Pr35 are speed adjustable. SP00 is the fastest, SP15 is the slowest. Ø Pr00 - Pr63：R,G,B,A,W,UV single color or multi-colors lighting Ø Pr64 - 6 Color Change mode Ø Pr65 - 6 Color Change + Strobe Ø Pr66 - Multi-Color Change Ø Pr67 - Multi-Color Change + Strobe 3. White balance setting（UtSt） Ø Press MENU to activate display / return to ‘main menu’ screen. Ø Press UP/DOWN until “UtSt” is displayed. Ø Press ENTER to proceed. Display will flash indicating you have entered edit mode. Ø Press UP/DOWN until desired selection is displayed (from 0 to 255). Ø Press ENTER to save and store your selections. The screen will stop flashing indicating you have exited edit mode. Note*** USon indicates white balance function is on. USoF indicates white balance function is off. SEon indicates the transfer of white balance data to other matching fixtures. SEoF indicates invalid. rEt indicates save and exit. When white balance data is set, press UP or DOWN until “rEt” is displayed and press ENTER to select and store your selections. Note*** Changing the white balance data controls the output of selected colors. For example, if r000 is set, when switching the white balance function to ‘On,’ there will be no red color output. 8
6. DMX Connections Ø DMX Cable： The MicroPar TRI 6 can be controlled via DMX using a 3-pin XLR connection. The standard DMX connection is XLR is: one end connects to the male plug, and the other connects to the female. As below: pin 1: ground, pin 2: negative signal, pin 3: positive signal
Noted：In order to avoid failures and interference signal transmission，we connect a resistance120Ω （ 1/4W ） at
the
end
of
the
DMX
connecting
as
below:
Ø The Conversion between 3 pin and 5 pin XLR If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable
9
7. Master/Slave Mode Operation Master/Slave Master/Slave mode allows you to connect multiple units together using one (1) unit to control others in a chain. When a fixture is set to ‘Master Mode,’ this unit will always act as a controlling unit until it is switched out of ‘Master Mode’. The Master unit will send out signal via DMX to Slave units which will react in synchronization. When a fixture is set into ‘Slave Mode’, this fixture will receive the Master signal. To ensure a fixture is in ‘Slave Mode’ the fixture’s display must read “SLAV”. To avoid master signal and DMX signal interference, do not connect DMX when using Master/Slave mode. If using a DMX run longer than 60 meters and/or over 32 units, a signal amplifier may be required.
8. Troubleshooting Problem
Solutions u Make sure that the DMX cable is properly connected
No DMX control
u Make sure that the DMX controller is operational u Check the DMX cable for tears or breaks u Make sure that the fixture is in DMX mode
Fixture does not respond to sound
u Make sure that the fixture is in Sound Active mode.
10
9. Technical Information
Input voltage: AC 100V-260V/50-60HZ Power Consumption: 25W Lamp Type: LED (3W) Lamp Spec: 6pcs 3in1 (RGB) Refresh rate :> 1.5KHz, Flicker Free Life span: 50,000~100,000 hours Control Signal: DMX512, sound activated, auto run Control mode: DMX512, Mater/Slave, Sound Activated, and Stand Alone DMX channels: 3/6/7/8 Beam Angle: 25° Cooling mode: Fan cooling Anti-electricity intension: >1.5KV Insulation Resistance: ＞２MΩ IP rated: IP20 Size: 136x120x232mm (5.3”x4.7”x9.1”) Net Weight: 1 KG (2.2 lbs)
Notice to consumer: ColorKey offers a 2 year limited warranty on all products. Please visit our website at www.ColorKeyLED.com to register your product.
Please note: As we continue to work towards improving our products and your experience as a user, we recommend that you check our website periodically for updates to user manuals and specifications at www.ColorKeyLED.com or you may contact us directly at
[email protected].
11
