Transcript
KB160/KB161 Series 1 2
DC-in
+12V 4-pin power (optional)
Backlight Power Select (JP7)
1
USB2.0 0-1 USB3.0 0-1 Power Select Power Select (JP13) (JP11)
USB 0 USB 3.0
1
1
System Fan
Dimming Mode Select (JP10)
LCD/Inverter Power
EXC Power
USB 1
USB 0-1
1
1
1
DDR3/DDR3L_1 SODIMM
1
5
Standby Power LED Panel Power ATX Select (JP8) Power
DDR3/DDR3L_2 SODIMM
39
ISL62771
40
LVDS LCD Panel
EXC
1
PTN3460
DisplayPort
13 1
Auto Power-on Select (JP2)
12
11
Front Panel ON
LVDS Channel and bpp Select (SW1)
AMD
24
LCD/Inverter Power Select 1 (JP9) 2 6
19 20
USB 2.0
12
1 2
1
2
2
Buzzer
1
CPU Fan 1
G-Series SoC SPI Flash BIOS
1
PS/2 Keyboard/Mouse Power Select (JP5)
VGA
Digital I/O Power
1
1
DIO Power Select (JP14)
Digital I/O Note: SATA 3.0 SATA1 supports SATA DOM.
USB 2-3 Power Select (JP12) USB 2.0 1
Mini PCIe
1
10
1
2
10
1 2
9 10 11
1
SATA Power 0
COM 3
LAN 2 1
10 2
1
9 1
1
1
SATA Power 1
Battery 10
COM 4
DFI Proprietary Extension Bus
4
4
12
9
2
SATA 1
LPC
2 1
1
Chassis Intrusion
SATA 0
2
COM 2
DIO 4-7 Output State (JP16)
1
Clear CMOS Data (JP1) 2 1 USB 2-3
LAN 1
1
1
9
DIO 0-3 Output State (JP15)
COM 1
9
12
SATA DOM Power Select (JP6) 1 78
LAN1 LAN1 LAN2 LAN2
State State State State
PCIe x4
PS/2 Keyboard/Mouse Power Select
JP5
Auto Power-on Select
JP2
+5V (default)
1-2 On
Power-on via power button (default)
1-2 On
+5V_standby
2-3 On
Power-on via AC power
2-3 On
USB Power Select: 3.0 0-1 (JP11), 2-3 (JP12), 2.0 0-1 (JP13)
Dimming Mode Select
+5V (default)
1-2 On
PWM Mode
1-2 On
+5V_standby
2-3 On
Voltage Mode (default)
2-3 On
Clear CMOS Data
JP1
Digital I/O Power Select
Normal (default)
1-2 On
Clear CMOS Data
2-3 On
LCD/Inverter Power Select
JP9
+12V
1-2 On
+5V (default)
2-3 On
Panel Power Select
1-2 On
+5V
3-4 On
+3.3V (default)
5-6 On
Backlight Power Select
1-2 On
+5V
2-3 On
1-2 On
+5V_standby (default)
2-3 On
+5V or +5V_standby (default)
1-2 On
GND
2-3 On
SATA DOM Power Select
JP7
+3.3V (default)
JP14
+5V
Digital I/O Output State: DIO 0-3 (JP15), DIO 4-7 (JP16)
JP8
+12V
JP10
Switch 1
1 On
1 Off
2 On
2 Off
LVDS Channel and bpp Select
Single LVDS
Dual LVDS
VESA (24bpp)
JEIDA or VESA (18bpp)
JP6
GND (default)
1-2 On
+5V
2-3 On
Note: 1. SATA 1 supports SATA DOM. 2. JP5 will be used when an EXC board is installed into the EXC interface on the motherboard for I/O expansion. 3. KB160 Series: 24-pin ATX power connector. 4. KB161 Series: 12V DC-in jack (default) or 4-pin power connector (optional). 5. SATA power 0 and SATA power 1 are populated on the KB161 board only. 6. SATA 0 is not populated on the system board while the Mini PCIe interface transmits the mSATA signal. 7. If you are installing one DDR3/DDR3L SODIMM only, make sure that the SODIMM 2 socket must be populated first.
Battery Notice Battery Usage The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source of power when the main power is shut off. Safety Measures • Danger of explosion if battery incorrectly replaced. • Replace only with the same or equivalent type recommend by the manufacturer. • Dispose of used batteries according to local ordinance. Mesure de Sécurité de l’usage de Batterie Batterie: • Danger d’explosion si la batterie n’est pas correctement remplacée. • Remplacez seulement avec le même type ou équivalent recommandé par le fabricant. • Traitez des batteries usées selon le règlement local.
www.dfi.com
934-KB1601-0A0G A30401402
