Mini Modular Headend

Transcript

MINI MODULAR HEADEND V40-300 and V41-Series MMH Mini-Modular-Headend page 1/9 Digital to Analogue VSB programme conversion for Hotel SMATV Headends V40-301F V40-306 V41-202 V40-400DSR V40-500DTR V40-800IPS V40-303 Base Unit (8 modules) Base Unit (6 modules) Digital Satellite to analogue VSB modulator Digital Satellite receiver to DVB-T COFDM Digital Terrestrial to DVB-T COFDM Transport stream to IP address (Ethernet) Link & Software V40-300 V41-201 V41-200 V40-700ENC V40-600DTM V40-900IPS VSB modulator DTT Tuner/VSB modulator MPEG Decoder /VSB modulator 3 x A/V to MPEG Encoder - TS 6 x TS to DVB-T modulator Ethernet IP to transport stream Vision Mini Modular Headend enables analogue and digital signals available from different sources to be combined and processed into transport streams for re-distribution as DVB-T COFDM and even IP addresses. MMH is designed for commercial, cable TV and hotel installation and is set up by PC software to control all the parameters in a digital headend. The base units have a high quality launch amplifier output with test point. Built in software monitors all aspects of the incoming and outgoing signal as well as the status of each module and the power supply.            Converts digital terrestrial / satellite programmes to DVB-T & T2 HD COFDM or analogue TV with VSB modulation Converts analogue external source from composite A/V to MPEG transport stream and DVB-T COFDM Modulates A/V from external sources to VSB analogue channel or DVB-T COFDM Converts MPEG transport stream to IP (Ethernet) and IP (Ethernet) to transport stream for COFDM modulation Mix satellite, terrestrial and external signals in one headend unit Pick and choose transport streams to form DVB-T COFDM multiplex Intelligent base unit includes power supply, data-bus and launch amplifier in one unit PC/MAC software setup, interrogate, clone and data-log controls 2 base units Watchdog built in to tuner modules to monitor digital reception Input signal level, quality and diagnostics in receivers with data-log for fault analysis Wall or 19” rack mounting with built in cooling fans (V40-301F base unit) In the interests of continued product development & improvement, Vision Products (Europe) Ltd reserves the right to change product specifications, design & dimensions. Data correct at time of going to press 26/08/2015. E&OE © 2015 Vision Products (Europe) Ltd. Vision Products (Europe) Ltd, Redbourne Park, Liliput Road, Brackmills, Northampton NN4 7DT Tel: 01604 662748, Fax : 01604 662746 Email: [email protected] www.vision-products.co.uk Company Reg No. : GB 05044512 V40-300 and V41-Series MMH Mini-Modular-Headend V40-301F        page 2/9 Base units for 8 modules with PSU, integrated cooling fan, launch amplifier and software interface 450mm + flanges Base unit with SMPS, software interface and up to 102dBµV maximum output Hold 8 MMH module cards Intelligent data bus for “plug & play” installation High output launch amplifier with -20dB test point and 10dB level control Wall or 19” rack mounting Cover / lid with thumb screws included 300mm inc Fitted cooling fan unit connectors + cable entry V40-306       cont’d Base units for 6 modules with PSU, launch amplifier and software interface Base unit with SMPS, software interface and up to 96dBµV maximum output Hold 6 MMH module cards Intelligent data bus for “plug & play” installation High output launch amplifier with -20dB test point Wall mounting Cover / lid with thumb screws included Base Units Specification V40-301F Number of Module Slots V40-306 8 Frequency range output 6 47-862MHz Maximum output of launch amplifier (IMD3 –60) 96dBµV (6 modules) 102dBµV (8 modules) Gain adjustment 10dB Isolation between modules 20dB Test Output -20dB Output Connector Power requirement Power Consumption V40-301F / 306 Operating temperature (Unit must be installed vertically) Dimensions and weight Mounting Base Unit to PC connection / Handheld remote control F Female 240V AC 50Hz 125W / 100W 00C to +500C 451 x 300 x 126mm (8.0kg) Wall or 19” rack 10U high 375 x 235 x 126mm (6.5kg) Wall RS485 to USB / RS485 (requires V40-303 or V40-302) V40-301F / 306 require V40-303 USB link/software and a compatible PC or MAC to access the setup menus. Up to 2 base units (16 modules) can be controlled from the same software by linking the data bus with connector lead provided. In the interests of continued product development & improvement, Vision Products (Europe) Ltd reserves the right to change product specifications, design & dimensions. Data correct at time of going to press 26/08/2015. E&OE © 2015 Vision Products (Europe) Ltd. Vision Products (Europe) Ltd, Redbourne Park, Liliput Road, Brackmills, Northampton NN4 7DT Tel: 01604 662748, Fax : 01604 662746 Email: [email protected] www.vision-products.co.uk Company Reg No. : GB 05044512 V40-300 and V41-Series MMH Mini-Modular-Headend V40-303      Link and Software VSB multi-standard TV modulator Fully agile VSB modulator ideal for external A/V sources Crystal controlled and stabilised output Low-level harmonic and intermodulation RF level control Multi-standard PAL B/G/D/K/I/L/M/N Software controlled Software control for all settings including RF on/off, test pattern generator etc. 15-pin “sub D” plug to RCA Phono A/V lead supplied V41-200        page 3/9 Controls up to 2 x V40-301/306 base units Addresses up to 16 modules Connection through USB interface Identifies location and status of each module Enables configuration, cloning, diagnostics of each module V40-300         cont’d MPEG2 Decoder to VSB multi-standard modulator Decodes additional programmes from a single multiplex Compatible with V41-201 terrestrial and V41-202 satellite receivers Requires V40-301/306 base unit and V40-303 software and link Built-in VSB multi-standard modulator Software/hardware timed “watchdog” Low level harmonics and intermodulation Software controlled In the interests of continued product development & improvement, Vision Products (Europe) Ltd reserves the right to change product specifications, design & dimensions. Data correct at time of going to press 26/08/2015. E&OE © 2015 Vision Products (Europe) Ltd. Vision Products (Europe) Ltd, Redbourne Park, Liliput Road, Brackmills, Northampton NN4 7DT Tel: 01604 662748, Fax : 01604 662746 Email: [email protected] www.vision-products.co.uk Company Reg No. : GB 05044512 V40-300 and V41-200 Series MMH Mini-Modular-Headend V41-201        cont’d page 4/9 DTT / OFDM terrestrial digital receiver / VSB modulator Converts a DTT programme from a digital multiplex to a VSB analogue channel Compatible with V41-200 MPEG2 decoder for additional programmes in same multiplex Requires V40-301F/306 base unit and V40-303 software and link Built-in VSB multi-standard modulator Software/hardware timed “watchdog” Low level harmonics and intermodulation Software controlled V41-202        QPSK-PAL/SECAM digital receiver / VSB modulator Converts a satellite programme from a digital multiplex to VSB analogue channel Compatible with V41-200 MPEG2 decoder for additional programmes in same multiplex Requires V40-301/306 base unit and V40-303 software and link Built-in VSB multi-standard modulator Software/hardware timed “watchdog” Low level harmonics and intermodulation Software controlled Specifications Input Connection Input Audio Input Frequency range V40-300 modulator V41-200 MPEG DECODER V41-201 DTT RECEIVER V41-202 SATELLITE RECEIVER Composite Video + Audio MPEG 2 Transport Stream VHF/UHF via IEC connectors with loop-through Satellite IF F connectors with loop-through 20Hz to 6MHz 2 to 80Mbits/sec Level / impedance 1V ±3dB/75Ω Frequency range 20Hz to 15kHz Level / impedance 775mV / 10kΩ 174-230 / 470-862MHz 30-88 dBµV / 75Ω TV Modulator Standards PAL B/G/D/K/L/I Modulator RF Output (IMD3 – 60dB) 100dBµV / 75Ω Modulator Output Frequency Range 110 to 862MHz Carrier accuracy / Fine Tune of video carrier ≥14dB Output level adjustment 0 to 10dB S/N ratio (weighted) >57dB 2nd and 3rd order intermodulation / distortion <-60dB A/V ratio (software switchable) 12 or 16dB Amplitude modulation depth 75% Audio Level adjustment (software controlled) -6dB to +6dB in 2dB steps 2.5W 7W 7W 8W UNIT MUST BE INSTALLED VERTICALLY -100C to +500C Operating temperature Dimensions and weight 30-88 dBµV / 75Ω ±20kHz / 2.25MHz max in 0.25MHz step Return Loss Power consumption 950-2150MHz 45 x 115 x 106mm 0.24kg 45 x 115 x 220 0.42kg 45 x 115 x 220 0.42kg 45 x 115 x 220 0.44kg In the interests of continued product development & improvement, Vision Products (Europe) Ltd reserves the right to change product specifications, design & dimensions. Data correct at time of going to press 26/08/2015. E&OE © 2015 Vision Products (Europe) Ltd. Vision Products (Europe) Ltd, Redbourne Park, Liliput Road, Brackmills, Northampton NN4 7DT Tel: 01604 662748, Fax : 01604 662746 Email: [email protected] www.vision-products.co.uk Company Reg No. : GB 05044512 V40-300 and V41-200 Series MMH Mini-Modular-Headend V40 - 400DSR         cont’d page 5/9 8PSK / QPSK – COFDM (Digital Satellite Transmodulator) Ideal for translating digital satellite programmes into a DTT multiplex Converts SAT IF multiplex into COFDM modulated DVB-T / T2 (HD) VHF/UHF RF channel Can select up to 6 SD or 2 HD programmes from 1 Transponder and convert into a single COFDM channel (32mb/s max) MPEG2 Transport Stream (TS) output connector for use with additional IP Streamer or COFDM modulator RF input loop through 950 – 2150 MHz with switchable 18V LNB power Requires V40-301/306 base unit, V40-303 software and link Built-in DVB-T / T2 HD RF modulator Fully compatible with all existing MMH equipment TS processing EPG multiplexing PCR re-stamping Service filtering PSI/SI regeneration NIT generation PMT version monitoring TS output COFDM output V40 - 500DTR         DVB-T (T2) COFDM – COFDM (Digital Terrestrial Transmodulator) Ideal for selecting/removing digital terrestrial programmes and re-multiplexing Converts programmes from a single COFDM multiplex to COFDM modulated DVB-T VHF/UHF RF channel Can select up to 6 SD or 2 HD programmes from 1 Transponder and convert into a single COFDM channel (32mb/s max) MPEG2 Transport Stream (TS) output connector for use with additional COFDM modulator RF input loop through 47 – 862 MHz Requires V40-301/306 base unit, V40-303 software and link Built-in DVB-T / T2 RF modulator Fully compatible with all existing MMH equipment TS processing EPG multiplexing PCR re-stamping Service filtering PSI/SI regeneration NIT generation TS output COFDM output In the interests of continued product development & improvement, Vision Products (Europe) Ltd reserves the right to change product specifications, design & dimensions. Data correct at time of going to press 26/08/2015. E&OE © 2015 Vision Products (Europe) Ltd. Vision Products (Europe) Ltd, Redbourne Park, Liliput Road, Brackmills, Northampton NN4 7DT Tel: 01604 662748, Fax : 01604 662746 Email: [email protected] www.vision-products.co.uk Company Reg No. : GB 05044512 V40 – Mini Modular Headend V40 - 600DTM         COFDM Modulation cont’d page 6/9 6 x Transport Streams Serial Input DVB-T Modulator Ideal to modulate up to 6 programmes from various TS into a single terrestrial digital channel Converts TS transport stream into COFDM DVB/T VHF/UHF RF channel up to 32mb/s max 6 individual serial transport stream (TS) input connectors 6 SD or 2 HD programmes in a single multiplex Ideal for use with V41-700ENC (3 input Encoder), V41-202, V41-200,201 and 202 receivers. Requires V40-301/306 base unit, V40-303 software and link Built in DVB-T RF modulator Fully compatible with all existing MMH equipment TS processing EPG multiplexing PCR re-stamping Service filtering PSI/SI regeneration NIT generation 6 x TS inputs TS output COFDM output V40 - 701ENC        3-Programme/ Sources MPEG2 Encoder to 3-Transport Streams Ideal for 3 x camera, DVD or SkyTM receiver A/V outputs into MPEG2 transport streams Converts analogue composite Video/Audio signals into MPEG2 serial transport streams (TS) 3 composite video and stereo audio inputs with 15 pin D plug to RCA phono connectors 3 individual MPEG2 serial transport stream (TS) outputs Ideal for use with V40-DTM (Serial Input DVB-T Modulator) Requires V40-301/306 base unit, V40-303 software and link Fully compatible with all existing MMH equipment 3 composite video and 3 stereo audio inputs 3 x MPEG2 TS outputs MPEG2 TS PID control Video brightness, contrast, saturation and hue control Programmable audio and video compression bit rates Programmable audio sampling rate Audio level control Control by base unit data bus and MMH software Firmware upgradeable In the interests of continued product development & improvement, Vision Products (Europe) Ltd reserves the right to change product specifications, design & dimensions. Data correct at time of going to press 26/08/2015. E&OE © 2015 Vision Products (Europe) Ltd. Vision Products (Europe) Ltd, Redbourne Park, Liliput Road, Brackmills, Northampton NN4 7DT Tel: 01604 662748, Fax : 01604 662746 Email: [email protected] www.vision-products.co.uk Company Reg No. : GB 05044512 V40 – Mini Modular Headend COFDM Modulation V40-400DSR 8/QPSK - COFDM Specifications INPUT SECTION V40-500DTR COFDM - COFDM Satellite Transmodulator Frequency range (PR) 174-230 / 470-862MHz 45 – 85dBµV/75Ω Input bit rate <150Mbit/s 2dB (PR) 0/18V 500mA Input Modulation Standard Symbol Rate MPEG-2 with 6 x Serial Transport Stream (TS) 35 – 90dBµV/75Ω Input loop-thru gain LNB / Masthead Pre-Amp power V40-600DTM DVB-T Modulator VHF/UHF F connectors with RF loop-through 950 – 2150MHz Level / impedance page 7/9 Terrestrial Transmodulator Satellite IF F connectors with RF loop-through Input Connection Input cont’d 0/5V 100mA 8PSK/QPSK DVB-S/S2 (PR) COFDM, QAM16/QAM64 1 ~ 45MS/s OUTPUT SECTION Modulator Output Frequency Range (PR) 110 ~ 862MHz Modulator RF Output 100dBµV / 75Ω Output C/N >50dB MER >35dB Guard Interval (PR) 1/4 , 1/8, 1/16, 1/32 Output modulation (PR) COFDM, QAM16, QAM 64 Code rate (PR) 1/2, 2/3, 3/4, 5/6, 7/8 Channel bandwidth (PR) 7/8MHz Transmission mode Output level adjustment 2K (PR) 0 ~ 15.5dB in 0.5dB steps Power consumption 5.5V 2A 5.5V 1.8A 5.5V 1.3A Operating temperature 00C to +500C Dimensions and weight 45 x 115 x 232mm 0.44kg (PR) = Programmable with internal software V40 - 701ENC A/V ~ MPEG2 Encoder Number of Inputs Video Cable with 3 RCA phono x V/A inputs to 15pin sub-D socket on encoder card Encoding ISO/IEC13818-2 MPEG2 MP @ ML Resolution Frame rate Audio (PR) (PR) Encoding Sampling rate Compressed bit rate Audio mode Audio / Video multiplexing Compressed system bit rate 720 x 576 (25 fps) 720 x 480 (30 fps) 25 max PAL. 30 max NTSC ISO/IEC13818-3 (MPEG1 audio) layer 1/2 compliant (PR) (PR) (PR) 32kHz, 44.1kHz, 48kHz 32 ~ 384 Kb/s Stereo, Joint Stereo, Dual Channel, Mono ISO/IEC13818-1 MPEG2 TS 0.5 ~ 15Mb/s Compressed system bit rate mode Constant / variable Video input standard PAL , SECAM, NTSC Power consumption Operating temperature Dimension / Weight 5.5V 1A 00C to +500C 45x115x220.5mm 0.42kg In the interests of continued product development & improvement, Vision Products (Europe) Ltd reserves the right to change product specifications, design & dimensions. Data correct at time of going to press 26/08/2015. E&OE © 2015 Vision Products (Europe) Ltd. Vision Products (Europe) Ltd, Redbourne Park, Liliput Road, Brackmills, Northampton NN4 7DT Tel: 01604 662748, Fax : 01604 662746 Email: [email protected] www.vision-products.co.uk Company Reg No. : GB 05044512 V40-800IPS Transport stream conversion to IP address  Enables a transport stream to be converted to a single IP address  Single Ethernet RJ45 output port  Two transport stream inputs  One transport stream output  Compatible with all Vision MMH base units and software  Converts the TS from any MMH encoder or receiver to an IP address cont’d page 8/9 Model V40-800IPS TS input type Serial TS input bit rate 80Mbps max TS output type Serial TS output bit rate 80Mbps ASI input / output type 75 Ω ASI bit rate TSoIP 200Mbps Ethernet data rate 100/1000 Mbps Ethernet encapsulation IEE802.2 SNAP, Eth II IP support IPv4 IP address assignment [pr] DHCP or static IP Multicast support IGMP v2 TP per IP 1 ~ 7 [pr] TS encapsulation UDP or RTP FEC SMPTE 2022-1-2007 Jitter tolerance 1 ~ 500ms Direction of conversion TSoIP → TS, ASI output TS1, TS2, ASI, → TSoIP Current consumption 5.5V 1.5A Operating temperature range 00C to +500C Dimension / weight 47.5 x 117 x 220.5mm / 0.36kg The transport stream converter V40-800IPS takes a programme from a standard MMH module such as a V40-701ENC (a/v source) or V40-400DSR and converts it to an Ethernet IP address for distribution via a LAN or WAN internet connection. The unit has two TS inputs and one TS output for connection to sister units. The output carries a programme via the Ethernet at 4.5Mbps which is normal for a SD programme and derived from the encoder or receiver. Higher bit rate settings can be selected depending on the capacity of the network. In the interests of continued product development & improvement, Vision Products (Europe) Ltd reserves the right to change product specifications, design & dimensions. Data correct at time of going to press 26/08/2015. E&OE © 2015 Vision Products (Europe) Ltd. Vision Products (Europe) Ltd, Redbourne Park, Liliput Road, Brackmills, Northampton NN4 7DT Tel: 01604 662748, Fax : 01604 662746 Email: [email protected] www.vision-products.co.uk Company Reg No. : GB 05044512 V40-900IPS IP Address to Transport stream converter cont’d page 9/9 TSoIP receiver for up to 7 programmes receiving MPTS or SPTS stream with constant or variable input bit rate.  Enables reception of transport stream via Ethernet  Single Ethernet RJ45 input port  Up to 7 x MPEG Transport streams  Can be re-modulated as COFDM via V40-600DTM  Compatible with all Vision MMH base units and software This unit is connected to an Ethernet II connection and derives up to 7 programmes converting them into a transport stream for onward re-modulation such as COFDM (V40-600DTM) compatible with a DVB-T receiver. The ability to receive and convert a transport stream from an IP address makes programme delivery extremely flexible and easy. V40-900IPS enables  PCR re-stamping  Reception of transport stream via Ethernet  Multicast or unicast streams  PAT version monitoring  PMT version monitoring  Stream buffer for jitter removal Model V40-900IPS TS output type serial TS output bit rate (total) TSoIP Direction of conversion 70Mbps max per channel Ethernet data rate 10/100/1000 Mbps Ethernet encapsulation IEE802.2 SNAP, Eth II IP support IPv4 IP address assignment [pr] Static IP Multicast support IGMP v2 TP per IP 1 ~ 7 [auto recognition] TS encapsulation UDP or RTP TS packet length 188 byte TS stream support SPTS or MPTS Buffer size for jitter tolerance 64Mbit per channel Bit rate type CBR or VBR Current consumption TSoIP, → TS 0 0 C to1.2A +500C 5.5V Operating temperature range 00C to +500C Dimension / weight 47.5 x 117 x 220.5mm / 0.66kg In the interests of continued product development & improvement, Vision Products (Europe) Ltd reserves the right to change product specifications, design & dimensions. Data correct at time of going to press 26/08/2015. E&OE © 2015 Vision Products (Europe) Ltd. Vision Products (Europe) Ltd, Redbourne Park, Liliput Road, Brackmills, Northampton NN4 7DT Tel: 01604 662748, Fax : 01604 662746 Email: [email protected] www.vision-products.co.uk Company Reg No. : GB 05044512