Mississippi Swing Washbasin Pre-install Instructions

Transcript

Mississippi Swing Washbasin Pre-Install Instructions Fixed height with low wall unit (RP-40-41110) CONSTRUCTION The wall must be made of a material suited for screw mounting and approved for damp rooms. The hatched area is the minimum area for reinforcement of the wall. Reinforcement from floor to ceiling is advisable. (See page 8). Load-tested and safe up to 300kg (660 lbs). According to DS/EN 12182 the maximum user weight is 120kg (264 lbs). Max. tensile load of upper screws 88kg/screw (194lbs/screw) The washbasin is supplied with a set of 8 screws and rawlplugs suitable for mounting on a concrete wall. The fitter should always consider the material, condition and strength of the wall and use screws and rawlplugs suitable for the specific wall type. PLUMBING The drain hose is a flexible Ø32 (1 ¼”) hose. The water supply ends in 2 (two) 90° shut-off valves with ½” or 3/8” outside thread pointing downward (not included). The flexible water connection hoses from the washbasin end in Ø10 pipes. Adapter fittings from these pipes to the shut-off valves are available with Ropox and as standard plumbing components. If a location of the drain higher than the recommended positioning is required, there mayMississippi Swing Washbasin be a risk of reduced draining from the washbasin. For purchase of adapters for connection to various standard installations, see ”Connection www.opemed.net Adapters – Swing Washbasin”. Clockhouse, Dogflud Way NOTE:Surrey GU9 7UD Farnham, All dimensions are based on a washbasin height of 800mm (23 5/8”) above floor level. If a change of this height is required, the 1 01252 758 858 [email protected] (264 lbs). Max. tensile load of upper screws 88kg/screw (194lbs/screw) The washbasin is supplied with a set of 8 screws and rawlplugs suitable for mounting on a concrete wall. The fitter should always consider the material, condition and strength of the wall and use screws and rawlplugs PLUMBING The drain hose is a flexible Ø32 (1 ¼”) hose. The water supply ends in 2 (two) 90° shut-off valves with ½” or 3/8” outside thread pointing downward (not included). The flexible water connection hoses from the washbasin end in Ø10 pipes. Adapter fittings from these pipes to the shut-off valves are available with Ropox and as standard plumbing components. If a location of the drain higher than the recommended positioning is required, there may be a risk of reduced draining from the washbasin. For purchase of adapters for connection to various standard installations, see ”Connection Adapters – Swing Washbasin”. NOTE: All dimensions are based on a washbasin height of 800mm (23 5/8”) above floor level. If a change of this height is required, the recommended dimensions must be changed accordingly. www.opemed.net Clockhouse, Dogflud Way Farnham, Surrey GU9 7UD 2 01252 758 858 [email protected] Fixed height with high wall unit Fixed height with high wall unit (40-41120) (RP- 40-41120) CONSTRUCTION CONSTRUCTION The wall must be made of a The wall suited must be a material for made screw of mounting material suited for screw mounting and approved for damp rooms. and for is damp rooms. The approved hatched area the minimum The area is the areahatched for reinforcement of the wall. minimum area for floor to ceiling Reinforcement from reinforcement is advisable. of the wall. Reinforcement from floor to ceiling is advisable. Load-tested and safe up to 300kg Load-tested and safe to 300kg (660 lbs). According toup DS/EN (660 lbs). According to DS/EN 12182 the maximum user weight 12182 thefixed maximum user has been at 120kg (264 lbs). weight has been fixed at 120kg (264 Max.lbs). tensile load of upper screws Max. tensile load of upper screws 88kg/screw (194lbs/screw) 88kg/screw (194lbs/screw) The suppliedwith withaa The washbasin washbasin is supplied set screws and and rawlplugs rawlplugs set of 8 screws suitable formounting mountingonon concrete suitable for aa concrete wall. shouldalways always wall. The The fitter fitter should consider thematerial, material,condition condition and consider the and strength of the thewall walland anduse usescrews screws strength of and suitablefor forthe the and rawlplugs rawlplugs suitable specific type. specific wall wall type. PLUMBING PLUMBING The drain hose is a flexible Ø32 (1 ¼”) hose. The drain hose is a flexible Ø32 (1 ¼”) hose. The water supply ends in 2 (two) 90° shut-off valves The ends inthread 2 (two)pointing 90° shut-off valves (not withwater ½” orsupply 3/8” outside downward with ½” or 3/8” outside thread pointing downward (not included). included). The flexible water connection hoses from the The flexible end water from the washbasin washbasin inconnection Ø10 pipes.hoses Adapter fittings from end in Ø10 pipes. Adapter fittings from these pipes to these pipes to the shut-off valves are available with the shut-off valves are available with Ropox and as OpeMed and as standard plumbing components. standard plumbing If a location of thecomponents. drain higher than the recommended positioning is required, there may be a risk of reduced Ifdraining a location of the higher than the recommended from thedrain washbasin. positioning is required, there may be a risk of reduced For purchase of adapters for connection to various draining from the washbasin. standard installations, see ”Connection Adapters – Swing Washbasin”. For purchase of adapters for connection to various standard installations, see ”Connection Adapters – NOTE: Swing Washbasin”. All dimensions are based on a washbasin height of 800mm (23 5/8”) above floor level. If a change of NOTE: this height is required, All dimensions are basedthe on recommended a washbasin height of dimensions must be changed accordingly. 800mm (23 5/8”) above floor level. If a change of this height is required, the recommended dimensions must be changed accordingly. www.opemed.net Clockhouse, Dogflud Way Farnham, Surrey GU9 7UD 3 01252 758 858 [email protected] Height-adjustable with low wall unit Height-adjustable with low wall unit (40-41130) (RP-40-41130) CONSTRUCTION CONSTRUCTION The wall must be made of a material The wall made of and a material suited formust screwbemounting suited for screw mounting and approved for damp rooms. approved for area dampisrooms. The hatched the minimum The hatched area is theofminimum area for reinforcement the wall. area for reinforcement of to theceiling wall. is Reinforcement from floor Reinforcement from floor to ceiling is advisable. advisable. Load-tested and safe up to 300kg Load-tested and safetoup to 300kg (660 lbs). According DS/EN 12182 (660maximum lbs). According to DS/EN 12182 the user weight has been the maximum user weight has been fixed at 120kg (264 lbs). fixed at 120kg (264 lbs). Max. tensile load of upper screws Max. tensile(194lbs/screw) load of upper screws 88kg/screw 88kg/screw (194lbs/screw) The washbasin is supplied with a set of 10 screws suitable of 10 screwsand andrawlplugs rawlplugs suitable for mounting on aa concrete fitter for mounting on concretewall. wall.The The should alwaysalways consider the the fitter should consider material, material, condition conditionand andstrength strengthofof the wall and use screws and rawlplugs use screws and rawlplugs suitable for for the thespecific specificwall walltype. type. PLUMBING The drain hose is a flexible Ø32 (1 ¼”) hose. PLUMBING The water drain hose is aends flexible (1 ¼”) The supply in 2Ø32 (two) 90°hose. shut-off valves with ½” or 3/8” outside thread pointing The water supply ends in 2 (two) shut-off downward (not included). The 90° flexible water valves with ½” or 3/8” outside thread pointing connection hoses from the washbasin end in Ø10 downward (not included). pipes. Adapter fittings from these pipes to the shut The flexible water connection hoses from the shut-off valves are withAdapter OpeMedfittings and as washbasin end inavailable Ø10 pipes. standard plumbing components. If a location from these pipes to the shut-off valves are of the drain higher than the recommended positioning is available with Ropox and as standard plumbing required, there may be a risk of reduced draining components. from the washbasin. If a purchase location of drain for higher than the For of the adapters connection to recommended positioning is required, there various see ”Connection may bestandard a risk of installations, reduced draining from the washbasin. Adapters – Swing Washbasin”. For purchase of adapters for connection to various standard installations, see ”Connection NOTE: Adapters – Swing Washbasin”. All dimensions are based on adjustment of the washbasin from 750 - 900 mm (29 ½” – 35 ½”) NOTE: above floor level. If a change of this adjustment All dimensions are based on adjustment of the range is required, the recommended washbasin from 750 - 900 mm (29 ½” – 35 ½”) dimensions must be changed accordingly. above floor level. If a change of this adjustment range is required, the recommended dimensions must be changed accordingly. www.opemed.net Clockhouse, Dogflud Way Farnham, Surrey GU9 7UD 4 01252 758 858 [email protected] Height-adjustable with with high highwall wallunit unit Height-adjustable (40-41140) (RP-40-41140) CONSTRUCTION CONSTRUCTION The The wall wall must must be be made made of of aa material suited for screw material suited for screw mounting mounting and and approved approved for for damp damp rooms. rooms. The The hatched hatched area area is is the the minimum minimum area for reinforcement area for reinforcement of of the the wall. wall. Reinforcement from floor to Reinforcement from floor to ceiling ceiling is is advisable. advisable. Load-tested Load-tested and and safe safe up up to to 300kg 300kg (660 lbs). According to DS/EN (660 lbs). According to DS/EN 12182 12182 the the maximum maximum user user weight weight has been fixed at 120kg has been fixed at 120kg (264 (264 lbs). lbs). Max. Max. tensile tensile load load of of upper upper screws screws 88kg/screw 88kg/screw (194lbs/screw) (194lbs/screw) 89” 89” 226 226 PLUMBING PLUMBING The drain hose is a flexible Ø32 (1 ¼”) hose. The drain hose is a flexible Ø32 (1 ¼”) hose. The water supply ends in 2 (two) 90° shut-off The water endsoutside in 2 (two) 90° pointing shut-off valves withsupply ½” or 3/8” thread valves with ½” or 3/8” outside thread pointing downward (not included). downward included). The flexible(not water connection hoses from the The flexible water connection hoses from the from washbasin end in Ø10 pipes. Adapter fittings washbasin in Ø10 pipes. Adapter fittings from these pipesend to the shut-off valves are available theseRopox pipes and to the valves are available with asshut-off standard plumbing with Ropox and as standard plumbing components. Ifcomponents. a location of the drain higher than the If a location of the drain higher than thethere may recommended positioning is required, recommended positioning is required, there may be a risk of reduced draining from the washbasin. be a risk of reduced draining from the washbasin. For purchase of adapters for connection to For purchase of adapters for connection to various standard installations, see ”Connection various standard Adapters – Swinginstallations, Washbasin”.see ”Connection Adapters – Swing Washbasin”. NOTE: NOTE: All dimensions are based on adjustment of the All dimensions adjustment of ½”) the washbasin fromare 750based - 900on mm (29 ½” – 35 washbasin from 750 900 mm (29 ½” – 35 above floor level. If a change of this height- ½”) above floor range level. Ifisarequired, change of heightadjustment thethis recommended adjustment range is required, the recommended dimensions must be changed accordingly. dimensions must be changed accordingly. 186 186 731/4” 1/4” 73 The The washbasin washbasin is is supplied supplied with with aa set of 12 screws and rawlplugs set of 12 screws and rawlplugs suitable suitable for for mounting mounting on on aa concrete wall. The fitter concrete wall. The fitter should should always always consider consider the the material, material, condition condition and and strength strength of of the the wall wall and use screws and rawlplugs and use screws and rawlplugs suitable suitable for for the the specific specific wall wall type. type. www.opemed.net Clockhouse, Dogflud Way Farnham, Surrey GU9 7UD 5 01252 758 858 [email protected] Optional: Optional:Dock-in Dock-in (RP-40-40069) (40-40069) CONSTRUCTION CONSTRUCTION The wall must be made of a The wall must be made of a material suited for screw material suited for screw mounting and approved for damp mounting and approved for damp rooms. rooms. The hatched area is the The hatched area is the minimum area for reinforcement minimum area for reinforcement of the wall. of the wall. Reinforcement from floor to Reinforcement from floor to ceiling is advisable. ceiling is advisable. Load-tested and safe up to Load-tested and safe up to 300kg (660 lbs). According to 300kg (660 lbs). According to DS/EN 12182 the maximum user DS/EN 12182 the maximum user weight has been fixed at 150kg weight has been fixed at 150kg (330lbs). This ensures that a (330lbs). This ensures that a person of 200kg (440 lbs) may person of 200kg (440 lbs) may lean securely on the washbasin lean securely on the washbasin fastened to the Dock-in station. fastened to the Dock-in station. Max. tensile load of upper Max. tensile load of upper screws screws 98kg/screw (216 lbs) 98kg/screw (216 lbs) Applies to the fixed washbasins Applies to the fixed washbasins 40-41110 and 40-41120 40-41110 and 40-41120 The unit will be supplied with a The unit will be supplied with a set of 4 screws and rawlplugs set of 4 screws and rawlplugs suitable for mounting on a suitable for mounting on a concrete wall. The fitter should concrete wall. The fitter should always consider the material, always consider the material, condition and strength of the condition and strength of the wall and use screws and wall and use screws and rawlplugs suitable for the rawlplugs suitable for the specific wall type. specific wall type. NOTE: All dimensions are based on a fixed height of the washbasin of 800mm (23 5/8”) above floor level and a height adjustment from 750 to 900mm (29 ½” – 35 ½”). If a change of these dimensions is required, the recommended dimensions must be changed accordingly. In case of larger orders, a mounting template may be provided. Applies to the height-adjustable washbasins Applies to the height-adjustable washbasins 40-41130 and 40-41140 40-41130 and 40-41140 www.opemed.net Clockhouse, Dogflud Way Farnham, Surrey GU9 7UD 6 01252 758 858 [email protected] Connection Adapters – Swing Washbasin The components illustrated below are available as optional extras depending on the type of installation in the building. Water supply adapters Swing Wash Basin Adapters Installation in room (not included) 10mm -> 1/2" Item No. 97001667 1/2" thread 10mm -> 3/8" Item No. 97001668 3/8" thread 10mm -> 15mm Item No. 97001665 15mm pipe Hose from basin 10mm Water hose extensions Hoses from basin Coupling piece Extra hose 1/2" x 1/2", 0,5m (19,7”), steel Item No. 97001123 10mm 1/2" x 1/2", 1m (39,4”), plastic Item No. 97001120 10mm -> 1/2" Item No. 97001662 Drain adapters Swing washbasin Drain from washbasin Adapters No adapter required Ø32 (1 ¼”) Ø32 -> Ø40 Item No. 97001660 Ø32 -> Ø50 Item No. 97001661 Drain extensions Drain hose from washbasin Coupling piece Installation in room (not provided) ø32 (1 ¼”) Ø40 (1 ½”) Ø50 (2”) Extra drain hose Ø32 Flex hose, 27-62cm (10,6”-24,4”) Item No. 97001162 Ø32 (1 ¼”) Ø32-Ø32 Item No. 97001662 Ø32 Flex hose, 40-110cm (15,7”-43,3”) Item No. 97001161 www.opemed.net Clockhouse, Dogflud Way Farnham, Surrey GU9 7UD 7 01252 758 858 [email protected] Reinforcement ReinforcementsMaximum of walls should always comply with national standards Load - Reinforcement Reinforcements of walls should always comply with national standards Plasterboard 12,5 mm (x2) (water-resistant) Plasterboard 12,5 mm (x2) (water-resistant) Plywood 22 mm (x 2) Plywood 22 mm (x 2) Please refer to mounting instructions for indication of to themounting placement in Please refer instructions height plywoodofplate. for of indication the placement in height of plywood plate. Plasterboard 12,5 mm (x2)Plasterboard 12,5 mm (x2) Product Product Plywood 22 mm (x 2 Plywood so that tip anchor 22ofmm is not exposed) (x 2 so that tip of anchor is not exposed) Hollow between walls Hollow between walls Plasterboard (other side) Plasterboard (other side) Screw to fit wall type (seeScrew page 2) to fit wall type (see page 2) Washer Washer www.opemed.net Clockhouse, Dogflud Way Farnham, Surrey GU9 7UD 5 01252 758 858 [email protected]