Transcript
Installation
MNTZX1PB
IP66 Outdoor Power Box Package Contents
Power Box 1pcs
Rubber Plug 1pcs
Waterproof Cap 3pcs
Make sure to install the product in an area that can support the weight of the power box plus cameras and accessories. Make sure to seal the box and all cable entrances according to the instructions in this document. Check www.flirsecurity.com/pro for the latest compatibility list.
1 Hex Screw M6x25 4pcs Spring Washer 4pcs Small Flat Washer 4pcs
Mounting Bolt M8x55 4pcs Anchor 4pcs Anchor Cap 4pcs Large Flat Washer 4pcs
Loosen M6 screws (x2) on the left side of the top panel and open the power box. Loosen the M6 screws (x2) inside the power box and remove the mounting plate. Bottom cover
Allen Key 1pcs
Mounting plate
Power Box Overview
Dimensions (units: mm)
1
Mounting plate
2
Bottom cover
3
Top cover
4
Electrical safety cover
5
Rail
6
Loop buckle
7
Shaft
8
M20 conduit cap
9
M6 screw
10
Gasket
11
M20 gasket
12
Rubber plug
13
Waterproof film
14
Retaining ring
M6 screws inside power box (x2)
2
Use the mounting plate to mark holes for the mounting bolts (x4) and any cables you are running through the mounting surface. Use outer holes to mount power box to wall.
UP arrow on mounting plate should be pointed up and away from the mounting surface. You must leave at least 30mm of clearance from all sides of the mounting plate to leave space to install the power box.
NOTE: If installing power box on corner mount or pole mount, attach mounting plate to the mount using the bolts supplied with the corner or pole mount. Skip to step 5. Illustrations of complete installation shown below.
3
Drill holes for the mounting bolts (x4) and cables. Insert the anchors (x4) and anchor caps (x4) into the holes as shown below. Run cables through the mounting surface.
Anchor and anchor cap (x4)
Weight (power box only): 1.7Kg / 3.7lbs www.flirsecurity.com/pro
MNTZX1PB_INSTALLATION_DIAGRAM_EN_R1
4
Place the mounting plate over the holes. Insert the mounting bolts (x4) and large flat washers (x4) to secure the mounting plate to the mounting surface.
7
Run the required cabling for the camera through the rubber plug on the top cover of the power box.
Rubber plug Mouting bolt and large flat washer (x4)
8 5
The below images show examples of items that can be installed to the power box. All items below are not included with power box. Check www.flirsecurity.com/pro for the latest compatibility list.
Run cables through rear M20 gaskets or bottom conduit holes.
Follow all instructions below. Incorrect installation of cables may impact the weatherproof rating of the power box.
Install any required equipment inside the power box. Install the mount (not included) and camera (not included) to the front of the power box with the hex screws (x4), spring washer (x4), and small flat washers (x4).
Hex screw, spring washer, and small flat washer (x4)
To run cables through rear M20 gaskets: 1. Poke a hole in the gasket with a nail or pin. 2. Run the cable through the gasket. 3. Attach the connector to the cable on the inside of the gasket.
Power module Lightning protection module
Air switch
Heater module
Connector Gasket
NOTE: Width of the rail is 35mm.
Cable
9
You must install the connector after pushing the cable through the gasket. You cannot push finished cables through the gaskets. The diameter of cables run through the gaskets must be between 3.5mm and 12mm. To run cables through bottom conduit holes: 1. Run cable without through the weatherproof cap. 2. Screw weatherproof cap into one of the bottom conduit ports. 3. Attach connector to cable inside power box.
NOTE: Bottom conduit diameter is M20-P1.5.
Cable Weatherproof cap
6
Place the power box over the mounting plate and slide into place. Tighten the M6 screws (x2) inside the power box to secure it to the mounting plate. Bottom cover Mounting plate
M6 screws inside power box (x2)
Push the top cover up about 2mm and then close the power box. Tighten the M6 screw (x4) on the front of the power box to secure the top cover and seal the power box.
Push up to close top cover M6 screw (x4)
