Preview only show first 10 pages with watermark. For full document please download

Mobile Navigation

Rating
Date

October 2018
Size

2.8MB
Views

6,540
Categories

Vehicles & accessories Motor vehicle electronics Car navigation systems

Transcript

www.blaupunkt.com Mobile Navigation TravelPilot Lucca 5.2 Operating and installation instructions Long version Lucca_5_2_long_1_GB.indd 1 07.12.2006 11:26:38 Uhr Device Overview 1 2 3 4 5 6 7 9 8 : ; < = > ? 2 Lucca_5_2_long_1_GB.indd 2 07.12.2006 11:26:38 Uhr Device Overview 1 VOLUME touch slider: Move your ﬁnger along the touch slider to change the volume (up to increase the volume, down to decrease the volume). 2 INFO button: Repeats the last travel instruction. 3 On/Off switch: Short press: Starts the device or switches it to idle state. Long press (longer than three seconds): Switches the device off. 4 MENU button: This button calls up the main menu. 5 Touchscreen: All entries and the control of Lucca are carried out in a simple and intuitive way by touching the buttons displayed on the touchscreen. 6 ZOOM/SCROLL touch slider: During the map display, you can zoom in and out. You can scroll through lists with this touch slider. 7 SD card slot. 8 Socket for connecting the Lucca to the battery charger or the charger cable for the cigarette lighter. 9 Headphone jack. : USB port for using a map reader for the SD card. ; Connection for Connect Cradle. < Reset button: Restarts the Lucca. = Battery cover. > GPS antenna input. ? TMC antenna input. 3 Lucca_5_2_long_1_GB.indd 3 07.12.2006 11:26:39 Uhr Contents Lucca scope of delivery ........................7 Safety notes ........................................7 Use as directed ..................................7 Safety notes for navigation ..................7 Safety notes for handling the Lucca ......7 Initial startup of Lucca .........................8 Protective ﬁlm and covers .......................8 Setting the Language .............................8 Reset ...................................................8 Charging the battery ............................8 Installation in the Vehicle ....................9 Attaching the Support.........................9 Removing the Support ........................9 Attach the Connect Cradle ..................9 Installing Lucca in the Connect Cradle ...9 Removing the Lucca ...........................9 Switching on/off ................................10 Initial switch-on ...............................10 Switch-on .......................................10 Activating the idle state .....................10 Switch-off .......................................10 Controls ............................................10 Basic buttons......................................10 Software keyboard ..............................10 Entering Blank Spaces ......................10 Entering numbers.............................10 Entering umlauts ..............................11 Deleting characters ..........................11 Lists ..................................................11 Performing Basic Settings ..................11 Setting the Time Zone .........................11 Entering the Home Address ..................12 Activating the PIN query .......................12 GPS Info .........................................12 Navigation ........................................13 General Notes about the Navigation .......13 Navigating to a destination address ........13 Entering a destination address ...........14 Navigating to a point of interest .............14 Selecting a point of interest ...............14 Selecting a point of interest nearby .....14 Selecting a point of interest at a speciﬁc location ...............................15 Using the travel guide...........................16 Selecting a travel destination .............16 Selecting a travel destination nearby ...16 Selecting a travel destination at a speciﬁc location ...............................17 Copying a Destination from the Map .......17 Moving the map section ....................17 Copying a destination from the Map ....18 Copying the Destination from the Favourites ..........................................18 Copying a Favourite for Destination Guidance ........................................18 Additional functions .........................19 Copying one of the recent destinations ...19 Additional functions .........................19 Using home address as destination ........19 Destination guidance ...........................20 Changing routing options ..................20 Disturbed GPS reception ...................20 Quitting the destination guidance .......21 Reaching the place of destination .......21 Managing Destinations .........................21 Saving destinations ..........................21 Saving one of the Recent Destinations ..21 Renaming a destination .....................21 Deleting a destination .......................22 Delete all destinations.......................22 Route Planning with Stages ...................22 Entering route points ........................22 Adding additional route points ...........23 Saving and editing routes ..................23 Changing the Order ..........................23 4 Lucca_5_2_long_1_GB.indd 4 07.12.2006 11:26:39 Uhr Contents Saving a route ..................................23 Loading a route ................................23 Deleting a Route Point .......................23 Deleting a Complete Route List ...........24 Calculating a route............................24 Displaying the Route on the Map .........24 Simulation..........................................24 Deﬁning routing options .......................24 Map Display during Destination Guidance .. 25 Navigation Tools ...............................25 Route Information ............................26 Signpost information ........................26 Speed Limit.....................................26 Working with the Map ..........................26 Map Operation.................................26 Showing a Map ................................26 Touching the map .............................26 Buttons ..........................................27 Additional functions .........................28 Day/night mode ...............................28 Mute ..............................................28 Block road, unblocking......................28 Inserting an Interim Destination..........28 Next destination...............................28 Settings ..........................................28 Route options ..................................28 Showing additional map information ...28 Route Information ............................29 Signpost information ........................29 Speed ............................................29 Additional Functions during Navigation ...30 Inserting an interim destination .............30 Approaching the next destination ..........30 Blocking route segments ......................30 Manual blocking ...............................30 Unblocking ......................................31 TMC function.....................................31 Connecting the TMC antenna ................31 Setting the TMC function ......................31 Showing trafﬁc jam reports ...................32 Conﬁguring Lucca .............................32 Settings in the main menu.....................32 Language ........................................32 Time...............................................33 Display ...........................................33 Factory settings ...............................33 Touchscreen ....................................33 Product information .........................33 Night mode .....................................34 Theft protection ...............................34 Button sound ...................................34 Audio / video ...................................34 Settings in the navigation menu .............34 Entering the Home Address ...............34 Map information ..............................35 Route information ............................35 Route planning.................................35 TMC ...............................................35 Select map ......................................36 Signpost information ........................36 Speed ............................................36 Auto mode ......................................36 Unit of measure ...............................37 Display ...........................................37 Volume ...........................................37 Voice output ....................................37 Data transfer .....................................38 Using road maps from the SD card .........38 Using media ﬁles from the SD card .........38 5 Lucca_5_2_long_1_GB.indd 5 07.12.2006 11:26:39 Uhr Contents Media player .....................................39 Inserting the SD card ...........................39 Starting the media player......................39 Playing music ﬁles ...............................39 Navigating through the music ﬁles.......39 Repeated play of music ﬁles (Repeat) ..39 Random play of music ﬁles (Shufﬂe) ...39 Changing to the music browser...........39 Showing image ﬁles .............................39 Navigating through the image ﬁles ......40 Display image folders ........................40 Rotating image ﬁles ..........................40 Changing to the picture browser .........40 Conﬁguring the slide show.................40 Starting the slide show......................40 Playing video ﬁles ................................40 Stopping playback ............................40 Connecting an external audio-video source ..............................40 Ending the media playback ...................41 Removing the SD card ..........................41 Connect Cradle .................................42 Pin assignment D-sub Connect Cradle ....42 Accessories ........................................43 Technical data ...................................43 Disposal of old unit ............................44 Service .............................................44 Warranty...........................................44 Frequently asked questions / FAQ .......45 Troubleshooting table ........................46 6 Lucca_5_2_long_1_GB.indd 6 07.12.2006 11:26:40 Uhr Scope of delivery | Safety notes Lucca scope of delivery The scope of delivery contains the following components: • Lucca • Suction cup holder • Charger cable for cigarette lighter • Battery charger for 110 V to 230 V • USB cable • Antenna for TMC reception • Operating instructions (short version) • DVD with road maps and operating instructions (long versions), reset program for a restore • Connect Cradle Safety notes For your personal beneﬁt, carefully read the following safety notes and warnings before operating your Lucca for the ﬁrst time. Use as directed The device is designed for mobile use in vehicles. The device can also be used by pedestrians. Special information about the navigation of trucks, busses and campers, such as altitude and width limitations or maximum permissible road load, is not included in the navigation data! Navigation off the roads (offroad) is only possible to a limited extent with the Lucca. Safety notes for navigation The street routing and trafﬁc signs have priority over the instructions of the navigation system. Follow the instruction of the Lucca only if circumstances and trafﬁc regulations allow! Lucca will bring you to your destination even if you have to deviate from the planned route. Notes: • Routes are best planned before starting your trip. If you want to enter a new route while on the road, please head for the next parking or rest area! • If you did not understand the voice information or if you are not sure what to do at the next intersection, use the map or arrow display for quick orientation. Safety notes for handling the Lucca Caution: Protect the device against moisture since it is not waterproof and not splashproof. Notes: • Remove the plug to the power supply of the Lucca if you are parking your vehicle for more than three days. The GPS receiver constantly uses electricity and could discharge the vehicle battery. • Do not unplug the connector by pulling on the wire. The wire could be damaged! • Do not use strong detergents for cleaning the device. Use only a moistened, lint-free cloth. Caution: Do not operate the Lucca while driving to protect yourself and others against accidents! View the display only if you are in a safe travel situation! 7 Lucca_5_2_long_1_GB.indd 7 07.12.2006 11:26:40 Uhr Initial startup of Lucca | Charging the battery Initial startup of Lucca Protective ﬁlm and covers Prior to the initial use, remove the protective ﬁlm from the display. Before inserting an SD card in the slot remove the dummy SD card. To protect the contacts, you can re-insert the dummy SD card after using the Lucca. Setting the Language If you are starting up the Lucca for the ﬁrst time, you must set the language for the menus and the voice output. 쏅 To switch on the Lucca, press the button 3. 쏅 In the main menu, touch Settings. 쏅 Touch Language. A list with available languages is displayed. 쏅 To scroll in the language list, move your ﬁnger along the touch slider 1. 쏅 Touch the preferred language. The language is loaded and the main menu is displayed. Reset The Lucca can be restarted by using the Reset button. 쏅 For this purpose, press the reset button < on the underside of the Lucca. Charging the battery The built-in battery allows for operating the Lucca via battery for up to ﬁve hours. The exact usage time is dependent upon the type of operation. The charge indicator of the battery is located in the top center of the screen. The number of dark block segments on the battery symbol indicates the charge state of the battery (0 to 3 segments). The symbols have the following meaning: : The device is supplied by an external – power source. : The device is supplied by its internal – battery. The charge state of the battery is sufﬁcient. : The device is supplied by its internal – battery. The charge state of the battery is low. Note: If the charge state of the battery is very low, a warning message is displayed. 쏅 To charge the battery, attach the supplied battery charger or the charger cable for the cigarette lighter to the charging socket 8 an. Note: Use only original chargers for operating and charging the battery. The charging time is approx. 5 to 6 hours. Note: Do not discard any batteries in the household trash; instead, return them to the corresponding collection sites. 8 Lucca_5_2_long_1_GB.indd 8 07.12.2006 11:26:40 Uhr Installation in the Vehicle Installation in the Vehicle For temporary installation in a vehicle, the Lucca features a suction cup holder with a suction cup to attach it to the windshield. Caution: Install the Lucca so that it does not block your view and does not distract from the trafﬁc. Do not install the Lucca in the airbag deployment area. Ensure that the Lucca does not pose a threat to passengers in the vehicle in case of emergency braking. Attaching the Support The Lucca can be installed in the vehicle in a simple way using the supplied suction cup holder. 쏅 Locate a suitable place for installing the Lucca. To ensure a perfect hold, the glass must be free of dust and oil. If necessary, clean the glass ﬁrst using a lens cleaning tissue. 쏅 Press the suction plate of the support against the glass. 쏅 Push the lever on the suction support towards the glass. 쏅 The holder can now be adjusted. The track for mounting the Lucca must be aligned vertically. Removing the Support If you change vehicles, you can simply remove the support. 쏅 Push the lever on the suction support away from the glass. 쏅 Carefully loosen the suction plate at the edge from the glass so that air can enter between suction cup and glass. 쏅 Carefully pull the suction cup off of the glass. Attach the Connect Cradle The suction cup holder features a mount for the Connect Cradle. The Connect Cradle expands the functions of the Lucca. The chapter "Connect Cradle" provides information about connecting the Connect Cradle to your car sound system. 쏅 Snap the Connect Cradle with the suction cup holder into position. Installing Lucca in the Connect Cradle The Lucca features an opening on the underside for mounting the Connect Cradle. 쏅 Detach the elastic cover on the underside of the housing. 쏅 Place the Lucca on the mount of the Connect Cradle and snap the Lucca to the rear and into position. Removing the Lucca 쏅 Press the lever of the Connect Cradle at the rear side of the Lucca and pull the Lucca to the front. 쏅 Remove the Lucca to the top and out of the Connect Cradle. To protect the contacts, you can apply the elastic cover and dummy SD card again after using the Lucca. 9 Lucca_5_2_long_1_GB.indd 9 07.12.2006 11:26:41 Uhr Switching on/off | Controls Switching on/off Controls Initial switch-on During the initial switch-on of the Lucca, the software is loaded into the system. For this reason, the switch-on process may last up to one minute. The initial destination guidance also requires some more time than usual. Basic buttons • • • Switch-on 쏅 To switch on the Lucca, press the button 3. The device switches on. (If the device is in the idle state, the previously active display is shown again). Activating the idle state 쏅 To activate the idle state, brieﬂy push the but3 below the display. ton The Lucca switches to the idle state. Switch-off 쏅 To switch off the device, press and hold the 3 for longer than three seconds. button The Lucca is switched off. Note: A switch-off of the Lucca is only necessary if you do not operate the device for an extended period of time. Still, the Lucca requires a little bit of current even in the switch-off state. Hence, it is possible that the battery must be recharged after an extended period of time. • • • Touch the touch slider 6 up to scroll up in the list by one page (5 elements). Touch the touch slider 6 down to scroll down in the list by one page (5 elements). To scroll in a list, move your ﬁnger along the touch slider 6. Note: If the list features more than ﬁve elements, the scroll bar indicates the current position in the list. : Touch this button to return to the entry without selecting a list element. : Touch this button to change to the next page in the menu. More: Touch this button to obtain access to additional functions. Depending on the menu in which you are currently located, different functions are offered. Software keyboard If text entries are required, the touchscreen displays a software keyboard. You can perform all the entries on the touchscreen by touching the respective symbol with your ﬁnger. You can only enter capital letters. You do not have to enter any special characters or umlauts when entering city or street names. The Lucca completes these characters automatically. Entering Blank Spaces 쏅 Touch the button to enter a blank space. Entering numbers 쏅 Touch the button. The numeric keypad is displayed. 쏅 Touch one of the number symbols to enter a number in the text ﬁeld. To change back to the character keyboard: 쏅 Touch the button. 10 Lucca_5_2_long_1_GB.indd 10 07.12.2006 11:26:41 Uhr Basic Settings Entering umlauts button. 쏅 Touch the The umlaut keyboard is displayed. 쏅 Touch one of the umlaut symbols to enter an umlaut in the text ﬁeld. As soon as you enter an umlaut, the character keyboard is displayed again. Deleting characters 쏅 To delete a character, touch the button . Performing Basic Settings Before you work with the Lucca, • set the time zone of for your position so that the correct arrival times are displayed during the navigation, and • enter your home address to quickly navigate home from any location. Setting the Time Zone 쏅 In the main menu, touch the Settings button. Lists In many cases, you can display lists from which you can select an entry. This is the case, for example, if you do not enter the complete name of a place during the entry. After every entry of a letter, the text ﬁeld shows the ﬁrst entry that starts with the previously entered characters. To display a list with additional matching entries: 쏅 Touch the List button. The list is displayed. 쏅 Touch the entry in the list to select it. 쏅 Touch the OK button. The list element is selected. The entry menu is displayed. The Settings menu is displayed. 쏅 Touch Time. The Time menu is displayed. 쏅 Touch Zone. The Time zone menu is displayed. 쏅 Touch the time zone in the list that is valid for your current position (GMT without daylight savings time). Note: The selection is facilitated by the display of the capitols in the respective time zone. 쏅 Touch the OK button. 쏅 To switch the daylight saving time on or off, touch the Daylight savings time button. The button displays ON or OFF. Note: Adjust the corresponding settings if the time is changed at your position or if you drive into a different time zone. 11 Lucca_5_2_long_1_GB.indd 11 07.12.2006 11:26:41 Uhr Basic Settings 쏅 Touch the OK button. 쏅 Touch the Format button to toggle between 12-hour and 24-hour display. 쏅 Touch the OK button. The Settings menu is displayed. Entering the Home Address 쏅 On the second page of the Navigation menu, touch the Settings button. The Settings menu is displayed. 쏅 Touch the Home address button. 쏅 쏅 쏅 쏅 The Home address menu is displayed. Touch the Enter home address button. The Destination entry menu is displayed. Touch the Address button and enter your home address. See "Entering a destination address". Touch the Set as home address button. The address is copied into the Home address menu. Touch the OK button. The Settings menu is displayed again. Activating the PIN query 쏅 Touch the Conﬁgure theft protection button. 쏅 Follow the instructions and enter a self-selected PIN. 쏅 Touch the OK button. The initial conﬁguration of the PIN is followed by a request to enter a PUK. The PUK is used to unlock the Lucca if you should forget the PIN. 쏅 Follow the instructions and enter a self-selected PUK. To secure your PUK: 쏅 Register under http://puk.blaupunkt.com and follow the instructions. GPS Info The GPS Info menu contains information about your current position and your actual speed. In addition, you can also save your current position. 쏅 In the main menu of the Lucca, touch the Navigation button. The Navigation menu is displayed. button. 쏅 Touch the The display shows the second page of the Navigation menu. The PIN query allows you to lock out unauthorised persons from using the Lucca. 쏅 In the main menu, touch the Settings button. 쏅 On the second page of the Settings menu, touch the Anti Theft Protection button. 쏅 Touch the GPS Info button. • The Theft protection menu is displayed. • • The GPS Status menu is displayed. GMT: Greenwich Mean Time. London time without daylight saving time. Longitude/latitude: Current position. Entry of the eastern longitude and northern latitude. Altitude: Current altitude above sea level. 12 Lucca_5_2_long_1_GB.indd 12 07.12.2006 11:26:42 Uhr Navigation • • • • • • Satellites: Number of satellites received. The navigation requires signals from at least three satellites. HDOP: Horizontal Dilution of Precision. Indicates the quality of the positioning. In theory, values from 0 to 50 are possible, whereby the following applies: The lower the value, the more precise the positioning (value 0 = no deviation from the actual position). Values up to 8 are acceptable for navigation. Speed: Indicates the current speed of the vehicle. Position: Indicates the address of the current position (if possible). Save current position: Touch this button to save the current position to the favourites (only possible if a street has been located). button to close the GPS Touch the window. Navigation General Notes about the Navigation Caution: Do not operate the Lucca while driving to protect yourself and others against accidents! View the display only if you are in a safe travel situation! The street routing and trafﬁc signs have priority over the instructions of the navigation system. Follow the instruction of the Lucca only if circumstances and trafﬁc regulations allow! Lucca will bring you to your destination even if you have to deviate from the planned route. Note: To be able to extensively use the navigation of the Lucca, perform the basic settings before the ﬁrst navigation (see "Performing Basic Settings"). Navigating to a destination address 쏅 In the main menu of the Lucca, touch the Navigation button. The Navigation menu is displayed. 13 Lucca_5_2_long_1_GB.indd Sec1:13 07.12.2006 11:26:42 Uhr Navigation Entering a destination address 쏅 Touch the Destination entry button to enter a destination for the navigation. The Destination entry menu is displayed. 쏅 Touch the Address button. The Address menu is displayed. 쏅 Touch the City or Postal code button. The software keyboard is displayed. The software keyboard allows for entering the names of cities or streets as well as postal codes. More information can be found in the chapter "Controls". 쏅 Type the name of the city to which you want to navigate using the software keyboard by touching the letter buttons in sequence. Optionally, you can also enter the postal code. 쏅 Touch the OK button. The Address menu is displayed. If you want to enter a street name: 쏅 Touch the Street button. 쏅 Enter the street name using the software keyboard. If you want to enter a house number: 쏅 Touch the No button. The software keyboard is automatically displayed as numeric keypad. 쏅 Enter the House number using the software keyboard. 쏅 Touch the Start Navigation button. The navigation starts. The destination guidance is displayed. Navigating to a point of interest The points of interest or POIs include interest speciﬁc locations such as airports, railway stations, and garages. These points of interest are stored in the map material and can be used as a navigation destination. Selecting a point of interest 쏅 In the main menu of the Lucca, touch the Navigation button. The Navigation menu is displayed. 쏅 Touch the Point of interest button to select a special destination for the navigation. The Point of interest menu is displayed. You can now select one of the following points of interest: • Airport • Filling station • Railway station • Car dealer • Restaurant Note: Touch the More button to call up additional points of interest, such as port, trade fair or bank. The desired point of interest us selected by touching it. 쏅 Touch one of the symbols to navigate to the respective point of interest. You can now select whether you want to navigate to a point of interest in your vicinity or at a speciﬁc location. Selecting a point of interest nearby If you want to navigate to a point of interest in your vicinity: 쏅 Touch the ... nearby button. Note: This function is only available if a GPS signal is received. 14 Lucca_5_2_long_1_GB.indd Sec1:14 07.12.2006 11:26:42 Uhr Navigation First, select the maximum distance at which the point of interest may be located: 쏅 Touch the Distance button. A list of the distances is displayed from which you can select the desired distance. 쏅 Touch the distance you want to select. 쏅 Touch the OK button. The distance is selected. You can optionally limit the point of interest even further (e.g. a postal ofﬁce in a speciﬁc street or the ﬁlling station of a particular brand). Note: A more detailed limitation is not available for all points of interest. 쏅 Touch the Category button. A list of the available categories is displayed. 쏅 Touch the category you want to select. 쏅 Touch the OK button. The category is selected. The point of interest closest to your location is now shown on the Next button. 쏅 Touch the List button. A list of points of interest that corresponds to your speciﬁcations is displayed. 쏅 Touch the point of interest to which you want to navigate. If you want to save the point of interest: • For further details read the section "Saving a destination". 쏅 To start the navigation, touch the Start Navigation button. The navigation starts. Selecting a point of interest at a speciﬁc location If you want to navigate to a point of interest at a speciﬁc location: 쏅 Touch the ... in a city button. First select a country: 쏅 Touch the Country button to select a country. A list of the selectable countries is displayed from which you can select the desired country. 쏅 Touch the country you want to select. The country is selected. Next, select a city: 쏅 Touch the City or Postal code button. The software keyboard is displayed. You can enter the city or the postal code via the software keyboard. You can optionally limit the point of interest even further (e.g. a postal ofﬁce in a speciﬁc street or the ﬁlling station of a particular brand). Note: A more detailed limitation is not available for all points of interest. 쏅 Touch the Category button. A list of the available categories is displayed. 쏅 Touch the category you want to select. The category is selected. 쏅 Touch the List button. The selectable points of interest of this category are listed. 쏅 Touch the Direct entry button if you want to enter your own name for a point of interest. - or 쏅 Touch the point of interest to which you want to navigate. If you want to save the point of interest: • For further details read the section "Saving a destination". 쏅 To start the navigation, touch the Start Navigation button. The navigation starts. 15 Lucca_5_2_long_1_GB.indd 15 07.12.2006 11:26:43 Uhr Navigation Using the travel guide The travel guide allows you to be guided to tourist attractions during your vacation trip. Selecting a travel destination 쏅 In the main menu of the Lucca, touch the Navigation button. The Navigation menu is displayed. 쏅 Touch the Travel guide button to select a travel destination for the navigation. The MERIAN travel guide menu is displayed. You can now select one of the following travel destinations: • Restaurant • Attraction • Going out • Shopping • Hotel The second page of the MERIAN point of interest menu also contains the following travel destinations: • Leisure time • Golf 쏅 Touch one of the symbols to navigate to the respective travel destination. You can now select whether you want to navigate to a travel destination in your vicinity or at a speciﬁc location. Selecting a travel destination nearby If you want to navigate to a travel destination nearby: 쏅 Touch the ... nearby button. Note: This function is only available if a GPS signal is received. The Travel destination vicinity menu is displayed. First, select the maximum distance at which the travel destination may be located: 쏅 Touch the Distance button. A list of the distances is displayed from which you can select the desired distance. 쏅 Touch the distance you want to select. 쏅 Touch the OK button. The distance is selected. The Travel destination vicinity menu is displayed. You can optionally limit the travel destination even further (e.g. a restaurant in a speciﬁc street or a certain attraction). Note: A more detailed limitation is not available for all travel destinations. 쏅 Touch the Category button. A list of the available categories is displayed. 쏅 Touch the category you want to select. 쏅 Touch the OK button. The category is selected. The Travel destination vicinity menu is displayed. The travel destination closest to your location is now shown on the Next button. 쏅 Touch the List button. A list of travel destinations that corresponds to your speciﬁcations is displayed. 쏅 Touch the travel destination to which you want to navigate. If you want to save the travel destination: • For further details read the section "Saving a destination". 쏅 In the list view, touch the More button. A menu with additional options is displayed. 쏅 Touch the Start Navigation button. The navigation starts. 16 Lucca_5_2_long_1_GB.indd 16 07.12.2006 11:26:43 Uhr Navigation Selecting a travel destination at a speciﬁc location If you want to navigate to a travel destination at a speciﬁc location: 쏅 Touch the ... in a city button. First select a country: 쏅 Touch the Country button to select a country. A list of the selectable countries is displayed from which you can select the desired country. 쏅 Touch the country you want to select. The country is selected. Next, select a city: 쏅 Touch the City or Postal code button. The software keyboard is displayed. You can enter the city or the postal code via the software keyboard. 쏅 Touch the OK button. You can optionally limit the travel destination even further (e.g. a restaurant in a speciﬁc street or a certain attraction). Note: A more detailed limitation is not available for all travel destinations. 쏅 Touch the Category button. A list of the available categories is displayed. 쏅 Touch the category you want to select. The category is selected. 쏅 Touch the List button. The selectable points of interest of this category are listed. 쏅 Touch the Direct entry button if you want to enter your own name for a point of interest. - or 쏅 Touch the point of interest to which you want to navigate. 쏅 Touch the OK button. If you want to save the travel destination: • For further details read the section "Saving a destination". 쏅 Touch the More button. A menu with additional options is displayed. 쏅 Touch the Start Navigation button. The navigation starts. Copying a Destination from the Map This function allows you to select the destination for a navigation directly on the map. In addition to towns and streets, you can also quickly select points of interest. 쏅 In the main menu touch the Navigation button. The Navigation menu is displayed. 쏅 Touch the Destination entry button. The Destination entry menu is displayed. 쏅 In the destination entry, touch the From map button. The map is displayed. Moving the map section To view the desired destination area on the map, you can move the map section and zoom in/out. 쏅 Touch the touch slider 6 up to zoom out of the map section (reducing the map size). 쏅 Touch the touch slider 6 down to zoom into the map section (increasing the map size). 쏅 Touch the lower area of the map until the additional menu appears. 17 Lucca_5_2_long_1_GB.indd 17 07.12.2006 11:26:43 Uhr Navigation button to move the map 쏅 Touch the (the button must feature a yellow border). 쏅 Now touch the map and move the map in the desired direction. This process can be repeated at random until the desired map section is displayed. Copying a destination from the Map 쏅 Touch the town (street or point of interest) to be deﬁned as the destination for a few seconds. The town is identiﬁed by an orange-dotted circle. Information about the selected location is loaded from the data stock and displayed. The buttons are located below the information ﬁeld. They can be used to call up several functions that are available for the selected route point. You have the following options: • Touch the Start navigation button to use the selected location as place of destination for the navigation. Notes: • This function is only available with GPS reception. • If you use this function during a navigation, all previously deﬁned route locations (stages and destination points) are deleted! 쏅 Touch the Save button to save the selected destination. You can select the destination at any time from the list of favourites. 쏅 Touch the Search nearby button to search for a point of interest in the vicinity of the selected destination. 쏅 Touch the Interim destination button to add the selected destination to a route (as the next stage to be approached). 쏅 Touch the Add button to add the selected destination to the end of a route (as the last stage). The route point is subsequently identiﬁed on the map by a ﬂag and also entered in the route point list in the Itinerary menu. Note: If you use Add or Interim destination during a navigation, the route is immediately recalculated and the navigation is subsequently continued. button to return to the map 쏅 Touch the view without executing a function. Copying the Destination from the Favourites The favourites contain all the destinations you saved using the Save button. You can perform the following in this menu: • Accepting destinations for the navigation, • renaming navigation destinations, and • deleting saved destinations. Copying a Favourite for Destination Guidance 쏅 In the main menu touch the Navigation button. The Navigation menu is displayed. 쏅 Touch the Destination entry button. The Destination entry menu is displayed. 쏅 Touch the Favorites button. The Favorites menu is displayed. 쏅 Touch the desired destination. 쏅 Touch the OK button. The Address menu is displayed. The address of the selected destination is entered in the corresponding ﬁelds. How to delete or rename a saved destination is described in the chapter "Managing destinations". 쏅 Touch the Start Navigation button. The navigation starts. 18 Lucca_5_2_long_1_GB.indd 18 07.12.2006 11:26:43 Uhr Navigation Additional functions 쏅 Touch the More button to gain access to additional functions of the Favourites menu. The list of additional functions displays. It contains the following functions: 쏅 Touch the Show details button to show the address of the selected destination. 쏅 Touch the Delete entry button to delete the selected destination. 쏅 Touch the Delete all button to delete all destinations from the Favourites. For further details read the chapter "Deleting a destination". • Renaming an entry – Touch the Rename entry button to change the designation of the selected destination. Copying one of the recent destinations The destinations approached last are automatically stored in the Recent destinations list. You can perform the following in this list: • Accepting a destination for the navigation, • saving a navigation destination in the Favourites, and • deleting entries of the Recent destinations list. 쏅 In the main menu touch the Navigation button. The Navigation menu is displayed. 쏅 Touch the Destination entry button. The Destination entry menu is displayed. 쏅 Touch the Recent destinations button. Additional functions 쏅 Touch the More button to gain access to additional functions of the Recent destinationsmenu. The list of additional functions displays. It contains the following functions: • Delete entry: – Touch the Delete entry button to delete the selected destination. • Delete all: – Touch the Delete all button to delete all entries of the Recent destinations list. • Save in favourites: – Touch the Save in favourites button to save the selected destination in the Favourites. Using home address as destination If your home address is saved, you can quickly navigate home from any location contained in your map. How to save your home address is described in the chapter "Home address". 쏅 In the main menu touch the Navigation button. The Navigation menu is displayed. 쏅 Touch the Home button. The route calculation is performed and the navigation starts. Note: The route type used for the route calculation is automatically selected from the setting which you deﬁned in the Routing options menu. The Recent destinations menu is displayed. 쏅 Touch the desired destination. 쏅 Touch the OK button. The destination is copied and the address is entered in the corresponding ﬁelds. 19 Lucca_5_2_long_1_GB.indd 19 07.12.2006 11:26:43 Uhr Navigation Destination guidance If you touch the Start navigation button after the destination entry, the route is recalculated and the map is displayed. Your current position is represented by a yellow triangle. The route is highlighted in blue. Notes: • The route is calculated using the settings for the route calculation. • If the navigation for a route is started, the starting point is always the current position. The ﬁrst stage of the route is the ﬁrst deﬁned route point. Changing routing options You can change the routing options during destination guidance: 쏅 Touch any position on the map. The additional menu opens. For detailed information, read the chapter "Working with the map". 쏅 Touch any position on the map a second time. A window with additional functions opens. 쏅 Touch the Route options button. The Routing options menu is called up. For further details read the chapter "Deﬁning routing options". If you changed the routing options, the route is recalculated and the changed settings are included. Disturbed GPS reception A message appears after entering the destination if no adequate GPS signal is received. Note: If you are in an enclosed room, move to the outside. As far as possible, the Lucca requires an open line of sight to the sky. If the GPS reception is disturbed during the destination guidance, the navigation is stopped. As soon as the reception is re-established, the navigation system automatically recognises whether your position has changed and, if necessary, recalculates the route. At that time, you can simply continue your navigation. 20 Lucca_5_2_long_1_GB.indd 20 07.12.2006 11:26:44 Uhr Navigation Quitting the destination guidance to quit the destina쏅 Touch this button tion guidance. A conﬁrmation dialogue appears. 쏅 Touch OK to quit the destination guidance. If you quit the destination guidance before reaching your destination, the Navigation menu opens. You can now enter a new destination or continue the navigation to the original destination by selecting the original destination again from the "recent destinations". Reaching the place of destination As soon as you have reached the destination point, the message "You have reached your destination" appears. At this point, the map displays only your current position (yellow arrow). Managing Destinations Two lists are available in which individual destinations are saved: • In the Favourites • In the Recent destinations list Each destination you specify and the destinations from the Recent destinations list can be saved in the Favourites. This is particularly useful if you want to approach this destination repeatedly. Destinations from the Favourites can be renamed. You can delete individual destinations from both lists. Saving destinations Prerequisite: • You speciﬁed a destination as described in the chapter "Entering a destination address". 쏅 In the Address menu, touch the More button. A window with additional functions is displayed. 쏅 Touch the Save button. 쏅 Touch the OK button. The software keyboard is displayed. 쏅 Type a name for the destination address to be stored. 쏅 Touch the OK button. The destination address is stored in the Favorites menu with the selected name. Saving one of the Recent Destinations Prerequisite: • You opened the Recent destinations list as described in the chapter "Copying one of the recent destinations". 쏅 Select the destination to be saved in the Favourites. 쏅 Touch the More button. A window with additional functions is displayed. 쏅 Touch the Save in Favourites button. 쏅 Touch the OK button. The software keyboard appears for entering a name. 쏅 Enter a name for the destination. 쏅 Touch the OK button. The destination is saved in the Favourites. Renaming a destination 쏅 Open the Favourites menu as described in the chapter "Copying the destination from the favourites". 쏅 Select the destination to be renamed. 쏅 Touch the More button. A window with additional functions is displayed. 쏅 Touch Rename entry. 쏅 Touch the OK button. A menu for entering a name is displayed. 쏅 Enter a new name for the destination. 쏅 Touch the OK button. The destination is renamed. 21 Lucca_5_2_long_1_GB.indd 21 07.12.2006 11:26:44 Uhr Navigation Deleting a destination Prerequisite: • You opened the Favourites as described in the chapter "Copying the destination from the favourites". - or • You opened the Recent destinations list as described in the chapter "Copying one of the recent destinations". 쏅 Select the destination to be deleted from the list. 쏅 Touch the More button. A window with additional functions is displayed. 쏅 Touch Delete entry. 쏅 Touch the OK button. A conﬁrmation menu is displayed. 쏅 Touch Yes to delete the destination. - or 쏅 Touch No in order to not delete the destination. Delete all destinations Prerequisite: • You opened the Favourites as described in the chapter "Copying the destination from the favourites". - or • You opened the Recent destinations list as described in the chapter "Copying one of the recent destinations". 쏅 Touch the More button. A window with additional functions is displayed. 쏅 Touch Delete all. 쏅 Touch the OK button. A conﬁrmation menu is displayed. 쏅 Touch Yes to delete the list. - or 쏅 Touch No in order to not delete the list. Route Planning with Stages You can also perform the route planning without GPS reception, e.g. in the comfort of your home. Deﬁned routes can be saved for reuse so that you can plan any number of routes, e.g. for your vacation. Entering route points A route is planned as follows: 쏅 In the main menu of the Lucca, touch the Navigation button. The Navigation menu is displayed. button. 쏅 Touch the The display shows the second page of the Navigation menu. 쏅 Touch Routes. The Routes menu is displayed. 쏅 Touch Itinerary. The Itinerary menu is displayed. 쏅 Touch the Add button to deﬁne the ﬁrst route point. The Destination entry menu is displayed. 쏅 Deﬁne the route point similar to the destination entry. For more information, see the chapter "Entering a destination". 쏅 Touch the Add button. 22 Lucca_5_2_long_1_GB.indd 22 07.12.2006 11:26:44 Uhr Navigation The Itinerary menu is displayed. The deﬁned destination is listed as route point 1. 쏅 Repeat the steps for all additional destinations to be added to the route. Adding additional route points 쏅 Touch the Add button to deﬁne an additional route point. The Destination entry menu is displayed. 쏅 Enter a new route point similar to the destination entry. The new route point is inserted at the end of the route list. Saving and editing routes You can plan any type of routes. They can be saved and used for navigation at a later time. You can insert additional route points in the routes at any time, change the order of route points or display the route on the map. The Itinerary menu provides various buttons for this purpose: 쏅 Touch the route point you want to select. If the list features more than three entries, use the following buttons: 쏅 Touch the touch slider 6 up to scroll up in the list by one page (5 elements). 쏅 Touch the touch slider 6 down to scroll down in the list by one page (5 elements). Changing the Order 쏅 Select the route point to be moved. 쏅 Touch the More button. 쏅 Touch the Route point up or the Route point down button. 쏅 Touch OK. The Itinerary menu is displayed again, the selected route point is moved up or down in the route list by one position. 쏅 Repeat this process until the route point appears at the correct position in the route list. Saving a route 쏅 Touch the More button. 쏅 Touch Save route. 쏅 Touch OK. The software keyboard appears for entering a name. 쏅 Enter a name for the route. 쏅 Touch OK. The route points are saved. Loading a route 쏅 Touch the More button. 쏅 Touch Load route. 쏅 Touch OK. 쏅 Select the desired route. 쏅 Touch OK. The route is being loaded. Deleting a Route Point 쏅 Select the route point to be deleted. 쏅 Touch the More button. 쏅 Touch Delete from route. 쏅 Touch OK. The route point is deleted and the route list appears again. 23 Lucca_5_2_long_1_GB.indd 23 07.12.2006 11:26:45 Uhr Navigation Deleting a Complete Route List Prerequisite: • You opened the route list to be deleted. 쏅 Touch the More button. 쏅 Touch Delete entire list. 쏅 Touch OK. Calculating a route A planned route can also be calculated without GPS reception so that you can gain an overview of the trip before you start out. In this case, the ﬁrst deﬁned route point is set as the starting point of the route. Note: For a navigation, the current position is the starting point. The ﬁrst stage is the travel to the ﬁrst deﬁned route point. 쏅 Touch the Calculate button to calculate the complete distance as well as the estimated travel time of the route. The route is being calculated. A window displays the progress of the calculation. After the calculation is complete, the Itinerary menu displays the complete trip from the ﬁrst to the last route point and the estimated travel time for this trip instead of the Calculate button. In addition, the distance from the previous route point and the estimated travel time for this stage are displayed for each route point. Displaying the Route on the Map 쏅 Touch the Display button to display the complete route on the map. The map is displayed. The route is highlighted in blue. The speciﬁed route points are identiﬁed by ﬂags. Simulation 쏅 On the second page of the navigation menu, touch the Simulation button. The Simulation menu is displayed. 쏅 Touch the upper From: button to specify a starting point. The destination entry appears. Enter a starting point. If necessary, read the chapter "Entering a destination" again. 쏅 Touch the Add to simulation button. 쏅 Touch the lower To: button to specify a destination point. The destination entry appears. Enter a destination point. 쏅 Touch the Add to simulation button. 쏅 Touch Start simulation. The simulation starts. 쏅 Touch the button to quit the simulation. Otherwise, the simulation is repeated. Note: The simulation distance must be less than 100 kilometres. Deﬁning routing options In the Routing options menu, you can deﬁne the speed proﬁle of your vehicle, select the type of routing and exclude certain streets from usage. The Routing options are retained for every subsequent destination guidance. 쏅 In the Navigation menu, touch the Routing options button. 24 Lucca_5_2_long_1_GB.indd 24 07.12.2006 11:26:45 Uhr Navigation The Routing options menu is displayed. 쏅 Touch the Overview button to display an overview of the route options. The route options can also be subsequently changed in the Overview menu. Map Display during Destination Guidance During a navigation, the map display shows different navigation tools, route information and signpost information: 쏅 Touch the Speed proﬁle ﬁeld to change between the available proﬁles. 쏅 Touch the Type of routing ﬁeld to change between the various modes: • Dynamic route – With this option, trafﬁc announcements are incorporated in the calculation of the route. Without TMC reception, the Fast Route is calculated. • Quick route – This option calculates the shortest route for the required time. • Short route – This option calculates the shortest route for the kilometres to be travelled. 쏅 Sequentially touch the ﬁelds Interstates, Ferries and Tollways and specify whether they should be included in the route calculation or avoided. • Allowed – This option includes the corresponding street type in the calculation of the route. • Avoid – This option avoids the corresponding street type as far as possible. • Prohibited – This option does not include the corresponding street type in the calculation of the route. Navigation Tools The left and lower area of the map display the following navigation tools: • • • In case of actions that must be executed in brief succession, the next to one action is displayed in the small upper arrow ﬁeld. The yellow triangle represents your position on the map. A continually changing map section ensures that the current position is always closely centred on the map (so-called moving map). The large lower arrow ﬁeld displays the next action and the distance to the next action. – If you come closer to the action location, a bar is also displayed to the right of the large arrow ﬁeld instead of the distance: – The more yellow bars are displayed, the closer you are to the location of the next action. 25 Lucca_5_2_long_1_GB.indd 25 07.12.2006 11:26:45 Uhr Navigation • • The upper street ﬁeld displays the next street name. The lower street ﬁeld displays the current street name. Route Information The right area of the map displays the following route information: Caution The information on the digital road maps may be incorrect due to short-term changes (construction, etc.)! The trafﬁc situation and the local signpost information have priority over the information of the Lucca. Working with the Map – – – – : This symbol represents stages. All information below it refers to the next destination. : Estimated time of arrival. : Estimated remaining travel time. : Remaining kilometres to destination. Signpost information The upper area of the map displays signpost information you must follow: Note: This information can only be displayed if it is part of the map material. Speed Limit The right area of the map displays any speed limit that may apply: Note: This information can only be shown if it is part of the map material and activated in the navigation settings. Map Operation In this section you learn which information and which processing options are available in the map view. Depending on whether you display a map without or during the navigation, different options are available for operation. Showing a Map You can display the map: • During route planning, • to display destinations on the map, or • to copy destination from the map for the navigation. You can open the map view as follows: • Via the Show map button in the Navigation menu. • Via the From map button in the Destination entry menu. • Via the Show button in the additional functions in the Address menu after selecting a destination. Touching the map 쏅 Brieﬂy touch the map to display additional functions. Depending on whether you are currently in an active navigation or only display the map, only certain functions are available. 쏅 Touch the map for a few seconds to display information about the location you touched, and you can also select it as navigation destination. For further details, please read the section "Copying a destination from the map". 26 Lucca_5_2_long_1_GB.indd 26 07.12.2006 11:26:45 Uhr Navigation Buttons Different buttons are available in the map view with which you can adjust the display according to your needs. 쏅 Brieﬂy touch the map to display additional buttons. • Note: The additional buttons are time-controlled and disappear again after seven seconds. Fix position/Fix map – This button is only active during a naviga/ Fix tion. Touch the Fix position button to toggle the map map view between "Position ﬁxed" and "Map ﬁxed". – Map ﬁxed In this mode, the map is ﬁxed and the current position (yellow arrow) moves across the map. Note: This mode is automatically set as soon as you move the map. Otherwise, the map would always jump back to the current position. This mode should also be set if you want to select destination points from the map during the navigation. – Position ﬁxed (standard setting) In this mode (button with yellow border), the map is continually moved so that the current position (yellow arrow) is always closely centred in the bottom third of the map. • Move button to switch to the 쏅 Touch the Move move mode. – Move In the move mode (button with yellow border), you can move the map. For this purpose, touch the map, hold the pen or your ﬁnger pressed and move the map area in the desired direction. 쏅 Touch the button again to switch off the move mode. • Showing the complete route 쏅 Touch this button , to display the complete route on the map. Note: This function can be called only in the map display. The destination guidance does not allow for displaying the entire route. • Map in travel direction/Map to north / To – Touch the In travel direction button to toggle the map north view between travel direction and aligned to north. – Map in travel direction Touch this button to display the map in the travel direction. – Map to north Touch this button (button with yellow border) to align the map in the direction north. • 3D-view button to display the – Touch the map in a three-dimensional representation from a bird's eye view. • More (2D view) – Touch the More button to display the map in two-dimensional form again. • TMC status , button to display current 쏅 Touch the trafﬁc announcements. • Note: A description of the TMC functionality can be found in the chapter "TMC function". Close map / Quit navigation , to close the – Touch this button map or to quit the navigation. 27 Lucca_5_2_long_1_GB.indd 27 07.12.2006 11:26:46 Uhr Navigation Additional functions 쏅 Brieﬂy touch any position on the map. The additional menu is displayed. For further details read the chapter "Working with the map". 쏅 Touch the map a second time. The menu with the additional functions displays. Depending on whether you are currently in a navigation or only display the map, certain additional functions are now available. Next destination This function is only available during a navigation on a route with at least one interim point. Use this function if you want to skip the next route point. 쏅 Touch the Next destination button to approach the next to one route point. The route is recalculated so that the next to one route point can be approached as the next destination. For further details read the section "Approaching the next destination". Settings 쏅 Touch the Settings button to display the Settings menu. For further details read the section "Settings". Route options 쏅 Touch the Route options button to change the route options. For further details read the section "Route options". Day/night mode button to set the map dis쏅 Touch the play to "Night" or "Day". Mute button to switch the voice 쏅 Touch the instructions on or off. Block road, unblocking The Block road button is only available during a navigation. For further details read the section "Blocking route segments". Inserting an Interim Destination 쏅 Touch the Interim dest. button to insert a new interim destination during the navigation. The route is recalculated so that this interim destination can be approached as the next destination. Afterwards, all subsequent route points are selected. For further details read the section "Inserting an interim destination". Showing additional map information You can use the Lucca to deﬁne which additional information is displayed on the map. All settings are performed in the Settings menu. The additional information on the map is activated as follows: 쏅 On the second page of the Navigation menu, touch the Settings button. 쏅 Touch the Map information button. 쏅 If you activate the entry Info bar, the compass, altitude and current speed are displayed on the map in the lower right border. 28 Lucca_5_2_long_1_GB.indd 28 07.12.2006 11:26:46 Uhr Navigation 쏅 Activate the Point of interest entry so that all points of interest are displayed on the map (default setting). 쏅 Activate the Street names (2D) entry so that the street names are displayed on the map (only possible in 2-D display). button to return to the Set쏅 Touch the tings menu. Route Information 쏅 In the Settings menu, touch the Route information button. The Route information menu is displayed. 쏅 Switch the desired route information on or off with the corresponding buttons. The corresponding information for the next stage (upper area) and the complete route (lower area) is displayed on the map. 쏅 Touch the tings menu. button to return to the Set- Signpost information 쏅 On the second page of the Settings menu, touch Signpost information. The Signpost information menu is displayed. 쏅 Touch the Show trafﬁc signs button to activate or deactivate the display of the exit trafﬁc signs. button to return to the Set쏅 Touch the tings menu. Speed 쏅 On the second page of the Settings menu, touch Speed. The Speed menu opens. In the Speed menu you can deﬁne whether speed limits should be displayed during the navigation and whether you should be warned audibly if you are exceeding the speed limit. • Display signs 쏅 Touch the Show trafﬁc signs button to switch among the modes Always, On speeding only or Never. • Warning in urban areas – The Warning in urban areas button shows the level of the speed-reading at which you are audibly warned inside of build-up areas. 쏅 Touch the Warning in urban areas button to change the value or to set it to Never. • Warning in rural areas: – The Warning in rural areas button shows the level of the speed-reading at which you are audibly warned outside of buildup areas. 29 Lucca_5_2_long_1_GB.indd 29 07.12.2006 11:26:47 Uhr Navigation 쏅 Touch the Warning in rural areas button to change the value or to set it to Never . Warning • – Activate the Warning button to receive a warning for speed limits when wet. 쏅 Touch the OK button to save your settings. Your settings are accepted and included during the navigation. Additional Functions during Navigation The following functions can be used during a navigation: • Inserting an Interim Destination • Skipping a stage • Blocking route segments • Using the TMC functionality Inserting an interim destination During the navigation, you can insert a new interim destination at any time. The route is then recalculated so that this interim destination can be approached as the next destination. After reaching the interim destination, all remaining places of destination are selected. An interim destination is created as follows: Prerequisite: • You are in the map display during a navigation. 쏅 Brieﬂy touch any position on the map. 쏅 Touch the Interim destination button. The Destination entry menu is displayed. 쏅 Enter the place of destination as described in "Entering a destination". 쏅 Touch the Set as route point button. The route is recalculated and the deﬁned interim destination is selected as the next route point. Note: You can also select the interim destination directly from the map as described in the section "Copying a destination from the map". Touch Interim destination. Approaching the next destination This function is only available during a navigation on a route with at least one interim point. Use this function if you want to skip the next route point. 쏅 Touch the Next destination button to omit the next route point. The route is recalculated so that the next to one route point can be approached as the next destination. Blocking route segments Manual blocking You can manually block a route segment of your route for navigation. After the blocking, the route is recalculated. The blocked segment is evaded. Let's assume you are on the interstate and hear a trafﬁc announcement on the radio about a trafﬁc jam of 5 km on your route. A manual blocking of the segment then allows you to evade the trafﬁc jam. The manual blocking is only applicable to the current navigation and is no longer available for a new navigation or after a restart of the program. Route segments are blocked as follows: Prerequisite: • You are in the map display during a navigation. 쏅 Brieﬂy touch any position on the map. 쏅 Select the Block road entry. The Block road menu is displayed. 쏅 Enter the number of kilometres which you want to block, starting with your current position. 30 Lucca_5_2_long_1_GB.indd 30 07.12.2006 11:26:47 Uhr TMC function The route is recalculated and the blocked route segment is evaded. The blocked segment is marked in red. Unblocking 쏅 Brieﬂy touch any position on the map. 쏅 Select the Block road entry. The road blocking is cancelled and the navigation uses once again the original calculated route. TMC function The Trafﬁc Message Channel (TMC) supplies your Lucca with trafﬁc reports that are broadcast by the radio stations with the RDS (Radio Data System) signal. The broadcast trafﬁc reports can be included in the route calculation by the Lucca. In case of trafﬁc obstructions on the calculated route, they are utilised for calculating an alternate route. This allows the Lucca to present a dynamic navigation that is adjusted to the trafﬁc situation. TMC is available in the following countries: Austria, Belgium, Czech Republic Denmark, Germany, England, Finland, France, Italy, Netherlands, Norway, Spain, Sweden, and Switzerland. Connecting the TMC antenna 쏅 Connect the supplied TMC antenna to the TMC antenna input ? on the rear side of the Lucca. 쏅 Attach the TMC antenna with the suction cups as parallel as possible to the instrument panel. The Lucca can now receive trafﬁc reports, if available. Setting the TMC function 쏅 On the second page of the navigation menu, touch the Settings button. The Settings menu is displayed. 쏅 Touch the TMC button. The TMC menu is displayed. The TMC function for the route change can be used in this two ways: • Automatic: The Lucca automatically changes the destination guidance as soon as it receives information about trafﬁc obstructions. • With conﬁrmation: The Lucca suggests changing the destination guidance as soon as it receives information about trafﬁc obstructions. The suggested route changes must be conﬁrmed individually. 31 Lucca_5_2_long_1_GB.indd Abs1:31 07.12.2006 11:26:47 Uhr Conﬁguring Lucca Showing trafﬁc jam reports Conﬁguring Lucca 쏅 In the main menu of the Lucca, touch the Navigation button. The Navigation menu is displayed. button. 쏅 Touch the The display shows the second page of the Navigation menu. The Lucca features two menus in which you can perform settings: • Settings in the main menu: The properties of the device are deﬁned here. • Settings in the navigation menu: The properties of the navigation are deﬁned here. Settings in the main menu 쏅 Touch the TMC button. The trafﬁc jam reports are displayed. 쏅 Touch the arrow symbols to change between messages. You can perform settings in the main menu of the Lucca for the following areas: • Language • Time • Display • Factory settings • Touchscreen • Product information • Night mode • Anti-theft mode • Button sound (sound of the buttons) • Audio / video 쏅 In the main menu, touch the Settings button to conﬁgure the Lucca. 쏅 If you made changes to the settings, you can touch the OK button of the Settings menu to accept the changes you made. - or button to exit the Settings 쏅 Touch the menu without saving the changes. Language In the Language menu, you can deﬁne the language in which the menus of the Lucca are displayed. The voice outputs are also using the language speciﬁed. 쏅 Touch Language. A list with available languages is displayed. 32 Lucca_5_2_long_1_GB.indd 32 07.12.2006 11:26:48 Uhr Conﬁguring Lucca 쏅 Touch the language in the list that you want to use for menus and voice output. 쏅 Touch the OK button. The language is loaded and the main menu is displayed. Time 쏅 Touch Time. The Time menu is displayed. 쏅 Touch Zone. 쏅 Touch the time zone in the list that is valid for your current position (GMT without daylight savings time). Note: The selection is facilitated by the display of the capitols in the respective time zone. 쏅 Touch the OK button. 쏅 To switch to the daylight savings time, touch the Daylight savings time button. The button displays ON or OFF. Note: Adjust the corresponding settings if the time is changed at your position or if you drive into a different time zone. 쏅 Touch Format to toggle between 24-hour and 12-hour display. 쏅 Touch the OK button. Display In the Display menu, you can set the display brightness for day and night operation. • Brightness day 쏅 Touch this ﬁeld to set the display brightness for day operation and conﬁrm with OK. • Brightness night 쏅 Touch this ﬁeld to set the display brightness for night operation and conﬁrm with OK. Factory settings In the Factory settings menu, you can reset the navigation software to the factory settings and conﬁgure the USB interface. 쏅 Touch the Factory settings button. 쏅 Touch Navigation to reset the settings for the navigation to the factory settings. - or 쏅 Touch Multimedia to reset the settings for the media player to the factory settings. A conﬁrmation dialogue appears in both cases. 쏅 Conﬁrm the reset by touching Yes or cancel it by touching No. 쏅 Touch the USB button to deﬁne the type of USB interface (ActiveSync, MTP, MSD). Note: ActiveSync: The Lucca is recognised by MS ActiveSync. MTP: Media Transfer Protocol. This setting allows the MS Media Player 10 under MS Windows XP to recognise a mobile device. MSD: Mass Storage Device. The Lucca is recognised as mass storage device. Touchscreen In the Touchscreen menu, you can recalibrate (align) the touchscreen if it responds imprecisely to touches. 쏅 Touch the Touchscreen button. A conﬁrmation is displayed. 쏅 Touch Yes and follow the instructions on the display to calibrate the touchscreen. Product information 쏅 On the second page of the Settings menu, touch theProduct information button. The version of the card used and the software version of the navigation software are displayed. 33 Lucca_5_2_long_1_GB.indd 33 07.12.2006 11:26:48 Uhr Conﬁguring Lucca Night mode 쏅 On the second page of the Settings menu, touch the Night mode button. 쏅 Touch the Automatic night mode button to toggle between the options Active and Inactive. If automatic is active, the Lucca automatically switches to the night mode if you turn on the lights of the vehicle. Note: The automatic night mode requires that the Connect Cradle is connected with the car sound system via the Smart Cable. 쏅 Touch the Manual button to toggle between the options On and Off. If the manual option is switched on, your display setting (Brightness Night) is adopted. 쏅 Conﬁrm the setting with OK. Theft protection In the Theft protection menu, you can assign a PIN and a PUK to the Lucca to protect it against unauthorised use. The PIN can be changed at any time. Register under http://puk.blaupunkt.com to securely store your PUK. For further details read, please read the chapter "Activating the PIN query". Button sound 쏅 On the second page of the Settings menu, touch the Button sound button to activate or deactivate the sound when touching a button. 쏅 Conﬁrm the setting with OK. Audio / video 쏅 On the second page of the Settings menu, touch the Audio/Video button. 쏅 Touch the Video format button to switch among the video formats PAL, NTSC and SECAM. Settings in the navigation menu You can perform settings of the Lucca in the navigation menu for the following areas: • Home address • Map information • Route information • Route planning • TMC • Select map • Signpost information • Speed • Auto mode • Unit of measure • Display • Volume • Voice output 쏅 On the second page of the navigation menu, touch the Settings button to conﬁgure the Lucca. 쏅 If you made changes to the settings, you can touch the OK button of the Settings menu to accept the changes you made. - or 쏅 Touch the button to exit the Settings menu without saving the changes. Entering the Home Address 쏅 Touch the Home address button. The Home address menu is displayed. 쏅 Touch the Enter home address button. The Destination entry menu is displayed. 쏅 Touch the Address button and enter your home address. See "Entering a destination address". 34 Lucca_5_2_long_1_GB.indd 34 07.12.2006 11:26:48 Uhr Conﬁguring Lucca 쏅 Touch the Set as home address button. The address is copied into the Home address menu. 쏅 Touch OK. Map information 쏅 Touch the Map information button. The Map information menu is displayed. 쏅 If you activate the entry Info bar, the compass, altitude and current speed are displayed on the map in the lower right border. 쏅 Activate the Point of interest entry so that all points of interest are displayed on the map (default setting). 쏅 Activate the Street names (2D) entry so that the street names are displayed on the map (only possible in 2-D display). 쏅 Touch OK. Route information In the Route information menu, you can perform the following settings: 쏅 Touch the Route information button. The Route information menu is displayed. You can now select the following settings: • Complete: The points apply to the entire route. If you entered only one destination, only this destination applies. • Stage: These points apply to the next route point. – Distance: Activate this point to display the distance to the destination. – Duration: Activate this point to display the duration until the arrival. Arrival time: Activate this point to display the estimated time of arrival. 쏅 Touch the buttons to switch the settings on or off. 쏅 Touch OK. – Route planning In the Itinerary menu, you can deﬁne whether the calculation for the next stage should automatically be performed after reaching a stage. If the automatic calculation is activated, the route to the next stage destination is automatically calculated upon reaching a stage. If the automatic calculation is deactivated, you can navigate to the next stage destination by briefly touching any position on the map and selecting the option Next destination. 쏅 Touch the Itinerary button. 쏅 Touch the Automatic button to switch the automatic route calculation on or off. 쏅 Touch OK. TMC In the TMC menu you can specify whether the Lucca should automatically perform route changes in case of trafﬁc obstructions or wait for manual conﬁrmation. 쏅 Touch the TMC button. 쏅 Touch the Route change button to toggle between the settings Automatic and Conﬁrm manually. 쏅 Touch OK. Note: A detailed description of the TMC functionality can be found in the chapter "Using the TMC functionality". 35 Lucca_5_2_long_1_GB.indd 35 07.12.2006 11:26:48 Uhr Conﬁguring Lucca Select map In the Select map menu, you can select a different map material. This function is only available if you saved map material on the SD card. 쏅 Touch the Select map button and select a map by touching it. Signpost information In the Signpost information menu, you can specify whether signpost information, which you are to follow, should be displayed during the navigation or not. 쏅 On the second page of the Settings menu, touch the Signpost information button. 쏅 Touch the Show trafﬁc signs button to switch the display on or off. 쏅 Touch OK. Note: This information can only be displayed if it is part of the map material. Speed In the Speed menu you can deﬁne whether speed limits should be displayed during the navigation and whether you should be warned audibly if you are exceeding the speed limit. 쏅 On the second page of the Settings menu, touch the Speed button. The Speed menu is displayed. You can now select the following settings: • Display signs 쏅 Touch the Show trafﬁc signs button to change between the following modes: – Always – On speeding only – Never • 쏅 • 쏅 • 쏅 쏅 Warning in urban areas – The Warning in urban areas button shows the level of the speed-reading at which you are audibly warned inside of build-up areas. Touch the Warning in urban areas to change the value or to set it to Never. Warning in rural areas – The Warning in rural areas button shows the level of the speed-reading at which you are audibly warned outside of buildup areas. Touch the Warning in rural areas to change the value or to set it to Never. Warning Activate the Warning button to receive a warning for speed limits when wet. Touch OK. Note: This information can only be displayed if it is part of the map material. Caution: The information in the map material may be incorrect due to short-term changes (construction, etc.)! The trafﬁc situation and the local signpost information have priority over the information of the navigation system. Auto mode In the Auto mode menu, you can perform the following settings: • Start with – Select whether the map should be displayed in 3-D view or in 2-D view by default. • 3D auto zoom – Select whether you desire Autozoom or No autozoom as default in 3-D view during a navigation. 36 Lucca_5_2_long_1_GB.indd 36 07.12.2006 11:26:49 Uhr Conﬁguring Lucca • 2D auto zoom – Select whether you desire Low autozoom, Standard autozoom, High autozoom or No autozoom as default in 2-D view during a navigation. Note: For 2-D and 3-D auto zoom, the zoom depth is changed in reference to your speed: If you travel slowly, the scale becomes smaller. If you travel faster, the scale becomes larger. The deeper the auto zoom, the smaller the scale of the map. • 2D-view – Select whether the map should be oriented to the north or in driving direction by default during a navigation with 2-D view. 쏅 On the second page of the Settings menu, touch the Auto mode button. The Auto mode menu is displayed. 쏅 Touch the buttons to perform the settings. 쏅 Touch OK. Unit of measure In the Unit of measure menu, you can deﬁne the units of measure to be used for time and distance. 쏅 On the second page of the Settings menu, touch the Unit of measure button. The Unit of measure menu is displayed. • Time 쏅 Touch this ﬁeld to toggle between 12-hour and 24-hour display. • Distance 쏅 Touch this ﬁeld to toggle between the display in kilometres and miles. 쏅 Touch OK. Display In the Display menu, you can set the display brightness for day and night operation. 쏅 On the second page of the Settings menu, touch the Display button. The Display menu is displayed. • Brightness day 쏅 Touch this ﬁeld to set the display brightness for day operation and conﬁrm with OK. • Brightness night 쏅 Touch this ﬁeld to set the display brightness for night operation and conﬁrm with OK. Volume In the Volume menu, you can set the volume. 쏅 On the second page of the Settings menu, touch the Volume button. The Volume menu is displayed. 쏅 Touch the Volume ﬁeld and select a different value. 쏅 Touch OK. Voice output In the Voice output menu, you can select whether the voice output should also use the loudspeakers if a Connect Cradle is connected. The active audio source of the car sound system is muted during a voice output. 쏅 On the third page of the Settings menu, touch the Voice output button. The Voice output menu is displayed. 쏅 Touch the Radio mute button to toggle between the voice output via loudspeakers (button with check mark) and the voice output only via Lucca (button without check mark). 쏅 Touch OK. 37 Lucca_5_2_long_1_GB.indd 37 07.12.2006 11:26:49 Uhr Data transfer Data transfer Using road maps from the SD card You can provide the Lucca with data (road maps, music data, image ﬁles and video ﬁles) via an SD card. The Lucca supports SD cards with a storage capacity of up to 4 GB. Depending upon the country in which the Lucca was purchased, either a road map for northern Europe or for southern Europe is preinstalled in the memory of the Lucca. The supplied DVD contains both road maps. To install a road map: 쏅 Copy the road map by using the installation program supplied on the DVD to your SD card. To use the road map in the Lucca: 쏅 Insert the SD card in the SD card slot 7. 쏅 In the main menu touch the Navigation button. 쏅 Touch the Settings button. 쏅 Touch the Select Map button. A list of the available road maps is displayed. 쏅 Touch the desired road map in the list to select it. 쏅 Touch the OK button. Caution: Risk of damage Changing the ﬁles in the internal memory may render the Lucca inoperable. If you connect the Lucca with your Windows computer via a USB cable, you have access to the SD card and to all ﬁles located on the internal memory of the Lucca. Refrain from editing or deleting ﬁles on the internal memory of the Lucca. Access only the SD card. Note: If you selected the USB interface type ActiveSync, MS ActiveSync version 3.7 or later must be installed on the computer. Only then can the computer access the Lucca and the SD card. As an alternative, you can also transfer the data to the SD card using an SD card reader. If you want to transfer data with the supplied USB cable: 쏅 Insert your SD card into the SD card slot 7 until the SD card engages. 쏅 Connect the Lucca with a Windows computer using the supplied USB cable. The computer recognises the Lucca as an SD card reader. The SD card and the internal memory of the Lucca are displayed as drives. Note: The USB port is intended for data transfer only. Do not attempt to charge the battery of the Lucca via USB. Using media ﬁles from the SD card The media player of the Lucca allows you to play the following media ﬁles: • MP3 and WMA for music ﬁles, • JPG and BMP for image ﬁles, and • WMV for video ﬁles. 쏅 Copy the media ﬁles to the SD card. 쏅 Start the media player. The media player automatically locates the data on the SD card and displays them in the browser. Note: Use the supplied USB cable to transfer WMV ﬁles to the Lucca. Use MS media player version 10 or higher and MS ActiveSync. 38 Lucca_5_2_long_1_GB.indd Abs2:38 07.12.2006 11:26:49 Uhr Media player Media player Inserting the SD card The SD card slot is located on the right side of the Lucca 7. 쏅 Insert your SD card into the SD card slot 7 until the SD card engages. Note: First exit the media player to insert a different SD card Navigating through the music ﬁles The playback menu displays a list of all music ﬁles that can be played back (except for shufﬂe mode). 1 2 1 Play music ﬁle 2 Select next music ﬁle from the list 3 4 3 Select previous music ﬁle from the list 4 Cancel playback Starting the media player 쏅 In the main menu of the Lucca, touch the Multimedia button. The Multimedia menu is displayed. Playing music ﬁles 쏅 Touch the My Music button. The music browser is displayed. You can sort your music ﬁles as follows in the music browser: • Album: Assigns the music ﬁles on your SD card to the respective albums. • Artist: Shows only music ﬁles from a certain musician. • Genre: Sorts music ﬁles according to certain musical genres. • Playlist: Shows the playlists that are stored on your SD card. • Song: Shows an alphabetically sorted list of all music ﬁles on your SD card. 쏅 Touch the respective list entry you want to select. Depending upon the sort, additional lists may be displayed with which you can reﬁne your selection even further. Touch the list entries here that you want to select. If you reached the list with the music ﬁles: 쏅 Touch the music ﬁle you want to play. 쏅 Touch the Play button. The music ﬁle is played back. Repeated play of music ﬁles (Repeat) 쏅 In the music browser, touch the Repeat button. A check mark is displayed behind Repeat. Every music ﬁle selected is repeated until you select a new music ﬁle. If you want to cancel the Repeat mode: 쏅 In the music browser, touch the Repeat button. The check mark behind Repeat is hidden. Random play of music ﬁles (Shufﬂe) 쏅 In the music browser, touch the Shufﬂe button. The media player now plays the music ﬁles on your SD card in random order. If you want to cancel the Shufﬂe mode: 쏅 In the music browser, touch the Shufﬂe button. The check mark behind Shufﬂe is hidden. Changing to the music browser 쏅 In the playback menu, touch the Browse button, or in the More menu, tough the Browser button. The music browser is displayed. Showing image ﬁles 쏅 Touch the My Pictures button. The picture viewer is displayed. 39 Lucca_5_2_long_1_GB.indd 39 07.12.2006 11:26:50 Uhr Mediaplayer 쏅 Touch the image ﬁle you want to display. The image ﬁle is displayed in the playback menu. Navigating through the image ﬁles The ﬁrst image is displayed in the picture viewer. 1 2 1 Show next folder 2 Show next image 3 Show previous image 4 Show previous folder 3 4 Display image folders 쏅 In the playback menu, touch the More button. A selection menu is displayed. 쏅 Touch the Show folder and picture name button to select between the options Yes and No. If you selected the option Yes, the folder name is displayed. Rotating image ﬁles 쏅 In the playback menu, touch the More button. A selection menu is displayed. 쏅 Touch the Rotate button to select among the options No, Left and Right. The image is rotated clockwise by 90 degrees. Changing to the picture browser 쏅 In the More menu, touch the Browser button. The picture browser is displayed. Conﬁguring the slide show You can set the display time for every image in a slide show. 쏅 In the playback menu, touch the More button. A selection menu is displayed. 쏅 Touch the Slideshow Timeout button repeatedly until the desired time is displayed. Note: The time is counted up in increments of ﬁve. An image can be displayed for up to 30 seconds. Starting the slide show 쏅 Touch the Slide Show Start button. The slide show is being started. 쏅 If you want to end the slide show, touch the image. The playback menu is displayed. Playing video ﬁles 쏅 Touch the My Videos button. The video browser is displayed. The video browser lists all video ﬁles on your SD card in alphabetical order. 쏅 Touch the video ﬁle you want to play. 쏅 Touch the Select button. The video ﬁle is played back. Stopping playback 쏅 Touch the display until the Pause button is displayed. 쏅 Touch the Pause button. The playback of the video ﬁle is stopped. If you want to continue the playback of the video ﬁle: 쏅 Touch the Play button. Connecting an external audio-video source You can connect an AV source to the Lucca by using an AV cable. For further details read the section "Connect Cradle". To view videos via the AV input: 쏅 Touch the My Videos button. 쏅 Touch the AV In button. 40 Lucca_5_2_long_1_GB.indd 40 07.12.2006 11:26:50 Uhr Mediaplayer Ending the media playback 쏅 In the My Music menu, touch the MENU button 4 to start a different application during the music playback. You can now start a slide show or a navigation while the media player continuous to play music. 쏅 In the media player menus, touch the button to exit the media playback. Removing the SD card 쏅 End the media player. 쏅 Carefully push on the SD card in the SD card slot until it disengages. The SD card is ejected a little bit from the SD card slot and can be removed. 41 Lucca_5_2_long_1_GB.indd 41 07.12.2006 11:26:50 Uhr Connect Cradle Connect Cradle The Connect Cradle allows you to transfer a composite video signal (back-up camera, DVD player). The 4-pole 3.5-mm jack connector contains one audio and video input. As soon as a signal is present at the Connect Cradle and the Lucca is installed in the Connect Cradle, the image and sound of the source is shown on the display of the Lucca (Lucca must be switched on). Pin assignment D-sub Connect Cradle Pin 1 6 11 5 10 15 Type Description 1 Ignition IN Car ignition signal IN (12V) 2 GND GND 3 GND GND 4 Analog OUT left Audio line OUT left channel 5 GND TMC Return TMC antenna Ground 6 Battery Plus 12/24 V DC Power IN 7 Speed Pulse Signal Continue nav. in case of GPS signal lost (5V) 8 TMC IN Car Audio TMC Signal IN (3.7-5V) 9 Analog OUT right Audio line OUT right channel 10 TMC-Antenna TMC signal Antenna (75-cm wire antenna) 11 GND GND 12 Dimming IN Illumination Signal IN (12V) 13 TMC-OUT Car Audio TMC Signal OUT (3.7-5V) 14 Audio mute Audio mute OUT (5V) 15 Analog GND GND 42 Lucca_5_2_long_1_GB.indd Abs3:42 07.12.2006 11:26:50 Uhr Technical data Accessories You can obtain a cable (Smart Cable) as an accessory which expands the functions of the Connect Cradle with the following functions: • • • • Power supply of the Lucca. Switching the Lucca on and off via ignition. Muting the radio for travel instructions. Voice output and music playback of the Lucca via the loudspeakers of the car sound system. • Speed signal (speedometer signal) to be able to continue navigating during GPS shadowing, e.g. inside a tunnel. The speed signal (speedometer signal) must be available in the vehicle at the radio connector. Technical data TFT display Active colour matrix, 4 inch, 16:9 diagonal, 480 x 272 pixel Audio Built-in loudspeaker: Mono, 8 Ohm, max 1 Wrms Audio output via Connect Cradle: Stereo, Vmax = 1 Veff, Rtyp = 600 Ohm Battery Voltage: 3.7 V Capacity: 2600 mAh Weight approx. 235 g Charger cable for cigarette lighter Input voltage: 12 V to 24 V Fuse in the connector: 2 A Battery charger Input voltage: 90 V to 240 V, 50/60 Hz Output voltage: 12 V Output current: max. 1 A GPS receiver 20-channel Nemerix Software © 2006 NAVIGON Company. All rights reserved. 43 Lucca_5_2_long_1_GB.indd 43 07.12.2006 11:26:51 Uhr Disposal of old unit | Service | Warranty Disposal of old unit Service (EU countries only) Do not dispose of your old unit in the household trash! Use the return and collection systems available to dispose of the old device. In some countries Blaupunkt offers a speciﬁc repair service including a pick-up service. In case your Lucca has to be sent to Blaupunkt for service you can order a pick-up service for your device on the internet. Refer to www.blaupunkt.com to check if this service is available in your country. Warranty We provide a manufacturer guarantee for our products bought within the European Union. Devices purchased outside the European Union are subject to the warranty terms published by our respective regional agency. You can view the warranty terms at www.blaupunkt.com or request them directly from: Blaupunkt GmbH, Hotline Robert-Bosch-Str. 200 D-31139 Hildesheim, Germany 44 Lucca_5_2_long_1_GB.indd 44 07.12.2006 11:26:51 Uhr Frequently asked questions / FAQ Frequently asked questions / FAQ The FAQ list contains exclusively answers to frequently asked questions. Information about solving problems or removing malfunctions can be found on the next page in the problem support table. Why does the Lucca require GPS reception? By using GPS satellites, the device determines where it is located and in which direction it is moving. Without GPS reception, navigating with the Lucca is not possible. Why does the Lucca require TMC reception? The Trafﬁc Message Channel (TMC) supplies your Lucca with trafﬁc reports that are broadcast by the radio stations with the RDS (Radio Data System) signal. Do I need a TMC-capable car sound system to receive the trafﬁc reports? No, the Lucca features a TMC receiver integrated in the device which allows for receiving trafﬁc reports - however, the TMC antenna must be connected to the Lucca for this purpose. Can I change the map material? Yes, you can change the map material. Depending upon the country in which the Lucca was purchased, either a road map for northern Europe or for southern Europe is preinstalled in the memory of the Lucca. For information about using the map material in the Lucca, please read the chapter "Data transfer". Which memory cards can I use? The Lucca is optimised for using commercially available SD cards. We tested SD cards from ScanDisk and Kingston. MMC cards can also be processed. Can I connect my video camera to the Connect Cradle? You can connect your video camera to the Connect Cradle and have the Lucca play back the video image and the sound track. Can I use the Lucca as a digital guide for hiking tours? Navigation off the roads (offroad) is only possible to a limited extent with the Lucca. For this reason, the Lucca is not suitable as a digital guide for hiking tours. How precise is the speed display of the Lucca? The speed display is generally even more precise than the vehicles speedometer; however, the Lucca cannot always precisely reﬂect acceleration processes since the GPS signal is refreshed only once every second. Can I operate the Lucca with a pen? No. Please use only the special entry pens for touchscreens that are commercially available. Can I play WMA music ﬁles with DRM protection using the Lucca? The playback of WMA ﬁles with Digital Rights Management protection (WMA-DRM) is not possible since the license key is not transferred during the transfer of the WMA ﬁle from the PC. The playback of WMA ﬁles without DRM protection is, of course, possible. 45 Lucca_5_2_long_1_GB.indd 45 07.12.2006 11:26:51 Uhr Troubleshooting table Problem Cause Solution The display remains dark if I The display may temporarily Place the Lucca in the shade for switch on the Lucca. loose its contrast after long and approximately ten minutes and heavy exposure to the sun and switch the device on again. high temperatures. The battery is not sufﬁciently Fully charge the battery. The charged. complete charging time is approx. 5 hours. The Lucca has no or only a very The Lucca has no GPS reception Press the Reset button and take poor GPS reception. for an extended period of time. the Lucca outside so that it can search for GPS signals again. Heavily metal-evaporated windshields may present an obstacle to the GPS reception of the Lucca. Connect a GPS antenna, which is available as an option, to the Lucca to improve the GPS reception. The Lucca has no or only a very The supplied TMC antenna is Connect the TMC antenna to the poor TMC reception. not connected or incorrectly Lucca or align the antenna difaligned. ferently. The TMC reception is currently TMC is currently available in not available in all European Austria, Belgium, Czech Repubcountries. lic Denmark, Germany, England, Finland, France, Italy, Netherlands, Norway, Spain, Sweden, and Switzerland. The media player does not play The media ﬁles on the SD card Transfer the media ﬁles in the some or all media ﬁles on my SD are stored in the wrong ﬁle for- formats MP3 and WMA for mucard. mat. sic, JPG and BMP for images and WMV for videos to the SD card. The SD card was formatted us- Format the memory card in ing the wrong formatting mode. the formatting mode FAT16 or FAT32. The media player does not The ﬁle uses a bitrate that is Use video ﬁles with a maximum smoothly play a video ﬁle on my not compatible with the media bitrate of 384 kbit per second. SD card. player. The Lucca does not respond The operating system of the Press the Reset button. when I touch the buttons. Lucca is overloaded. 46 Lucca_5_2_long_1_GB.indd 46 07.12.2006 11:26:51 Uhr Your notes 47 Lucca_5_2_long_1_GB.indd 47 07.12.2006 11:26:51 Uhr Problemhilfetabelle Country: Phone: Fax: Germany (D) 0180-5000225 05121-49 4002 Austria (A) 01-610 39 0 01-610 39 391 Belgium (B) 02-525 5444 02-525 5263 Denmark (DK) 44-898 360 44-898 644 Finland (FIN) 09-435 991 09-435 99236 France (F) 01-4010 7007 01-4010 7320 Great Britain (GB) 01-89583 8880 01-89583 8394 Greece (GR) 210 94 27 337 210 94 12 711 Ireland (IRL) 01-46 66 700 01-46 66 706 Italy (I) 02-369 62331 02-369 62464 Luxembourg (L) 40 4078 40 2085 Netherlands (NL) 00 31 24 35 91 338 00 31 24 35 91 336 Norway (N) +47 64 87 89 60 +47 64 87 89 02 Portugal (P) 2185 00144 2185 00165 Spain (E) 902 52 77 70 91 410 4078 Sweden (S) 08-7501850 08-7501810 Switzerland (CH) 01-8471644 01-8471650 Czech. Rep. (CZ) 02-6130 0446 02-6130 0514 Hungary (H) 76 511 803 76 511 809 Poland (PL) 0800-118922 022-8771260 Turkey (TR) 0212-335 06 71 0212-346 00 40 http://www.blaupunkt.com Blaupunkt GmbH, Robert-Bosch-Straße 200, D-31139 Hildesheim 10/06 CM-AS/SCS1 (GB) 8 622 405 292 48 Lucca_5_2_long_1_GB.indd 48 07.12.2006 11:26:51 Uhr

Mobile Navigation

Rating

Date

Size

Views

Categories

Share

Transcript

Forgot your password?.