Transcript
MODA GRAZE INTERIOR DMX I N S T A L L A T I O N 1
This product must be installed in accordance with the applicable installation code, by a person familiar with the construction and operation of the product and the hazards involved. Ensure power is off before installation, verify electrical plan first, read all installation instructions before beginning installation. With the constant development of our products please check our website (www.modalight.com) for any possible changes to the installation of this product. Este producto debe ser instalado de acuerdo con el código de instalación por una persona familiarizada con la construcción y operación del producto y los riesgos que entraña. Asegúrese que la electricidad este apagada antes de la instalación, verifique plan electrico, lea todas las instrucciones de instalación antes de comenzar instalación. Con el desarrollo constante de nuestros productos, visite nuestro web (www.modalight.com) para todos posibles cambios en la instalación de este producto. Ce produit doit être installé en conformité avec le code d’installation applicable par une personne familière avec la construction et l’exploitation du produit et les risques encourus. Assurer que l’alimentation est coupée avant l’installation , vérifier le plan électrique d’abord, lire toutes les instructions d’installation avant de commencer installation. Avec le développement constant de nos produits s’il vous plaît consulter le site web (www.modalight.com) pour toutles changements possibles à l’installation de ce produit.
DRY/DAMP LOCATION INSTALL INSTALACIÓN DE LUGARES SECOS/HÚMEDOS INSTALLATION EMPLACEMENT SEC/HUMIDE
2
Verify electrical plan and ensure all hardware is present. Verificar plan electrico y verifique que todo el equipo esté presente. Vérifier le plan électrique et assurer que tout le matériel est présent.
DMX Belden Controller 9841
DMX Splitter (Optional)
Belden Junction Leader 9841 Box Cable
Jumper Cable
Fixture to Fixture Terminator Connection
! Max Continuous Run: See Section 12 Continuidad Máxima: Vea sección 12 Run Continue Max: Voir la section 12
3
Mount fixture to surface by using the 4 inner screw holes. Monte accesorio a superficie utilizando los 4 agujeros para tornillos interiores. Mont fixation à la surface en utilisant les 4 trous de vis internes.
Due to continuous improvements and innovations, specifications may change without notice. Please refer to our website for current technical data. These figures are provided as a guideline only and may vary with differing power supplies and installtions. All rights reserved. E&OE.
VDC20161411
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775 F: 702 407 7773 | www.modalight.com | © Copyright 2016
MODA GRAZE INTERIOR DMX I N S T A L L A T I O N 4
Slide out the locking device sideways to allow fixture to rotate. Deslice hacia fuera el dispositivo de bloqueo hacia los lados para permitir accesorio para girar. Faites glisser le dispositif de verrouillage sur le côté pour permettre appareil à tourner.
5
Rotate fixture to desired angle, then lock the fixture in place by pushing the locking device in. Girar al ángulo deseado, y luego bloquear el accesorio en su lugar empujando el dispositivo de blockeo. Tournez luminaire à l’angle désiré, puis verrouiller l’appareil en place en poussant le dispositif de verrouillage.
180º Rotation 6
Apply screws to outer screw holes to complete the bracket locking process. Aplicar tornillos en orificios externos para completar el proceso de cierre del soporte. Applique vis aux trous de vis extérieur pour compléter le processus de serrage de l’étrier.
Due to continuous improvements and innovations, specifications may change without notice. Please refer to our website for current technical data. These figures are provided as a guideline only and may vary with differing power supplies and installtions. All rights reserved. E&OE.
VDC20161411
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775 F: 702 407 7773 | www.modalight.com | © Copyright 2016
MODA GRAZE INTERIOR DMX I N S T A L L A T I O N 7
For vertical applications, install the Bracket Lock. Para aplicaciones verticales , instale el soporte de bloqueo . Pour les applications verticales , installer le verrouillage Bracket.
! To prevent slidings, secure Bracket Lock to center of the bracket. Para prevenir deslizamientos, atornille el Soporte de bloqueo en el centro del soporte. Pour prévenir les glissements , Secure Lock Bracket centre du support.
Due to continuous improvements and innovations, specifications may change without notice. Please refer to our website for current technical data. These figures are provided as a guideline only and may vary with differing power supplies and installtions. All rights reserved. E&OE.
VDC20161411
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775 F: 702 407 7773 | www.modalight.com | © Copyright 2016
MODA GRAZE INTERIOR DMX I N S T A L L A T I O N 8
DMX Wiring - To ensure correct installation, the necessary items are required: Cablería de DMX - Para garantizar una instalación correcta, se requieren los elementos necesarios: DMX Câblage - Pour garantir une installation correcte, les éléments nécessaires sont nécessaires:
Belden 9841 Cable
Electrical Tape
Junction Box(es)
Wire Nuts
Single DMX Wiring - Please refer to section 8-A Belden 9841
100277v AC
100277v AC
DMX Controller
Terminator
Leader Cable 100277v AC
Multi Run DMX Wiring - Please refer to section 8-B Belden 9841
Belden 9841
100277v AC
Leader Cable
100277v AC
DMX Controller
Belden 9841
DMX Splitter
100277v AC
Terminator A1
A...
...A20
B1
B...
...B20
Terminator
Leader Cable
!
!
Fixtures must be programmed by MODA prior to shipping!
Must use Belden 9841 Cable for Data Connection.
Lámparas debe ser programado por MODA antes de ser enviadas!
Data y Electricidad deben estar en conductos separados!
Lampe doit être programmé par MODA avant qu’ils soient expédiés!
Les données et la puissance doivent être sur des conduits séparés!
!
!
Install must be done up to local code.
Use electrical tape to cover any exposed wires.
Instalar se debe hacer con los códigos locales.
Lámparas debe ser programado por MODA antes de ser enviadas!
Installer doit être fait au code local.
Lampe doit être programmé par MODA avant qu’ils soient expédiés!
!
!
Data and Power must be run in separate conduit!
Fixtures must be installed in correct order.
Data y Electricidad deben estar en conductos separados!
Lámparas debe ser programado por MODA antes de ser enviadas! Lampe doit être programmé par MODA avant qu’ils soient expédiés!
Les données et la puissance doivent être sur des conduits séparés!
Due to continuous improvements and innovations, specifications may change without notice. Please refer to our website for current technical data. These figures are provided as a guideline only and may vary with differing power supplies and installtions. All rights reserved. E&OE.
VDC20161411
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775 F: 702 407 7773 | www.modalight.com | © Copyright 2016
MODA GRAZE INTERIOR DMX I N S T A L L A T I O N 8-A Single run DMX Wiring Cablería de DMX para una sola continuidad Run simple DMX Câblage
DMX -
A. Strip both ends of the Belden 9841 cable B. Connect one end of the Belden 9841 cable to DMX Controller C. Connect other end of Belden 9841 cable to leader cable
(White, Blue Stripe)
DMX +
A. Despojar los dos extremos del cable Belden 9841 B. Conecte un extremo del cable Belden 9841 al controlador DMX C. Conecte el otro extremo del cable Belden 9841 al cable líder
(Blue, White Stripe)
!
A. Dépouiller les deux extrémités du câble Belden 9841 B. Branchez une extrémité du câble Belden 9841 DMX Controller C. Branchez l’autre extrémité du câble Belden 9841 câble leader
Use electrical tape to cover any exposed wires Utilize cinta electrica para cubrir cables expuestos Utilisez du ruban électrique pour couvrir tous les fils exposés.
A
Belden 9841 Cable
DMX Controller
100 - 277v
DMX Control
B
8 PIN Moda Graze Int Leader Cable
DMX Controller (Belden 9841)
100-277 v
C
8 PIN Moda Cove Int Leader Cable
WIRING LEGEND 8 PIN LEADER CABLE
DMX CONTROLLER
Power Positive (AWG 18)
Positive
Power Negative (AWG 18)
Negative
Ground (AWG 18)
POWER (100-277v AC)
DMX Positive
Positive
DMX Negative
Negative Ground
Due to continuous improvements and innovations, specifications may change without notice. Please refer to our website for current technical data. These figures are provided as a guideline only and may vary with differing power supplies and installtions. All rights reserved. E&OE.
VDC20161411
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775 F: 702 407 7773 | www.modalight.com | © Copyright 2016
MODA GRAZE INTERIOR DMX I N S T A L L A T I O N 8-B Multiple run DMX Wiring Cablería de DMX para multiples continuidades Exécuter plusieurs DMX Câblage
DMX -
A. Strip both ends of Belden 9841 cable B. Connect one end of Belden 9841 cable to DMX Controller C. Connect other end of Belden 9841 Cable to DMX Input/Output adapter D. Connect DMX Input/Output cable to Moda DMX Splitter
(White, Blue Stripe)
DMX +
(Blue, White Stripe)
A. Despojar a ambos extremos del cable Belden 9841 B. Conecte un extremo del cable Belden 9841 al controlador DMX C. Conectar el otro extremo del cable Belden 9841 a DMX de entrada / adaptador de salida D. Conectar el cable DMX de entrada / salida a Moda DMX Splitter
! Use electrical tape to cover any exposed wires
A. Dépouiller les deux extrémités du câble Belden 9841 B. Branchez une extrémité du câble Belden 9841 DMX Controller C. Connectez l’autre extrémité du câble Belden 9841 DMX Input / adaptateur de sortie D. Branchez le câble d’entrée / sortie DMX à Moda DMX Splitter
Utilize cinta electrica para cubrir cables expuestos Utilisez du ruban électrique pour couvrir tous les fils exposés.
A
Belden 9841 Cable
DMX +
DMX -
(Blue, White Stripe)
B
DMX Control
(White, Blue Stripe)
DMX Input/Output adapter
C
DMX Controller
DMX Splitter
DMX Control to Moda DMX Splitter
D
WIRING LEGEND 8 PIN LEADER CABLE
DMX CONTROLLER
Power Positive (AWG 18)
Positive
Power Negative (AWG 18)
Negative
Ground (AWG 18)
Belden 9841
POWER (100-277v AC)
DMX Positive
Positive
DMX Negative
Negative Ground
Due to continuous improvements and innovations, specifications may change without notice. Please refer to our website for current technical data. These figures are provided as a guideline only and may vary with differing power supplies and installtions. All rights reserved. E&OE.
VDC20161411
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775 F: 702 407 7773 | www.modalight.com | © Copyright 2016
MODA GRAZE INTERIOR DMX I N S T A L L A T I O N 8-B Multiple run DMX Wiring Cablería de DMX para multiples continuidades Exécuter plusieurs DMX Câblage
DMX -
E. Strip both ends of Belden 9841 cable F. Connect stripped ends of Belden 9841 cable to DMX Input/Output adapter G. Connect DMX Input/Output adapter to Moda DMX Splitter Output H. Connect other end of Belden 9841 cable to MODA GRAZE INT Leader Cable E. Despojar ambos extremos del cable Belden 9841 F. Conecte extremos pelados del cable Belden 9841 al adaptador DMX de entrada / salida G. Conectar DMX adaptador de entrada / salida a la salida DMX Splitter Moda H. Conecte el otro extremo del cable Belden 9841 a cable lider de MODA GRAZE INT
(White, Blue Stripe)
DMX +
(Blue, White Stripe)
! Use electrical tape to cover any exposed wires
E. Dépouiller les deux extrémités du câble Belden 9841 F. Connecter les extrémités dénudées de Belden 9841 Câble DMX entrée / adaptateur de sortie G. Connectez DMX adaptateur d’entrée / sortie de Moda DMX Splitter sortie H. Branchez l’autre extrémité du câble Belden 9841 à Câble MODA GRAZE leader INT
Utilize cinta electrica para cubrir cables expuestos Utilisez du ruban électrique pour couvrir tous les fils exposés.
E
Belden 9841 Cable
DMX +
DMX -
(Blue, White Stripe)
(White, Blue Stripe)
Belden 9841 to DMX Input/Output Adapter
F
G
Moda DMX Splitter-8 to Fixture Run
DMX Controller
Moda DMX Splitter (Belden 9841)
DMX Splitter
100-277 v
8 PIN Moda Cove Int Leader Cable
100 - 277v
8 PIN Moda Graze Int Leader Cable
H JUNCTION BOX CONNECTION Due to continuous improvements and innovations, specifications may change without notice. Please refer to our website for current technical data. These figures are provided as a guideline only and may vary with differing power supplies and installtions. All rights reserved. E&OE.
VDC20161411
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775 F: 702 407 7773 | www.modalight.com | © Copyright 2016
MODA GRAZE INTERIOR DMX I N S T A L L A T I O N 9
Connect leader cable and place terminator. Connectar cable líder y colocar Terminador. Raccorder le fil de chef de file et le lieu de terminaison.
To release, pull down on latch and pull.
CLICK!
Connect Terminator
! Terminator MUST be placed on final fixture!
10
Terminator DEBE ser colocado en el último accesorio! Terminator DOIT être placé sur dernier match !
Connection types
CLICK!
Tipos de connexiones Types de connexion Jumper Cable
Fixture to Fixture
Minimum bend radius of fixture to fixture connection is 90°
Leader Cable
Connect Terminator
Jumper Cable
!
Sizes can be mixed, Do Not Exceed Max Run Lengths (see section 12) Se pueden combinar tamaños, No Exeder Longitud Maxima. (vea sección 12) Vous pouvez combiner tailles, Dépasser Aucune Longueur Maximale. (voir la section 12)
Due to continuous improvements and innovations, specifications may change without notice. Please refer to our website for current technical data. These figures are provided as a guideline only and may vary with differing power supplies and installtions. All rights reserved. E&OE.
VDC20161411
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775 F: 702 407 7773 | www.modalight.com | © Copyright 2016
MODA GRAZE INTERIOR DMX I N S T A L L A T I O N 11
Power on! Encender! Allumer!
12
Run lengths information Ejecutar longitudes de información Run longueurs d’informations
13
PRODUCT
1ft using 120v AC
1ft using 277v AC
4ft using 120v AC
4ft using 277v AC
RGB
80 pcs
80 pcs
20 pcs
20 pcs
RGBW
80 pcs
80 pcs
20 pcs
20 pcs
RGBA
80 pcs
80 pcs
20 pcs
20 pcs
Dynamic Cool
80 pcs
80 pcs
20 pcs
20 pcs
Dynamic Warm
80 pcs
80 pcs
20 pcs
20 pcs
Dynamic White
80 pcs
80 pcs
20 pcs
20 pcs
Setback chart Gráfica de retroceso Chart Abaissement
1 feet
1.5 feet
10 Foot Wall
15 Foot Wall
2 feet
2.5 feet
20 Foot Wall
25 Foot Wall
! Recommended setback from the wall is 1/10 of the wall height. Retroceso de la pared recomendada es 1/10 de la altura del muro. Revers recommandée de la paroi est de 1/10 de la hauteur du mur.
Due to continuous improvements and innovations, specifications may change without notice. Please refer to our website for current technical data. These figures are provided as a guideline only and may vary with differing power supplies and installtions. All rights reserved. E&OE.
VDC20161411
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775 F: 702 407 7773 | www.modalight.com | © Copyright 2016
MODA GRAZE INTERIOR DMX I N S T A L L A T I O N 14
Optics beam angles Ángulos de rayos opticos para Angles optics poutre 6˚
6˚
10˚
6° 40˚
10˚
25˚
10° 40˚
10˚
40° 30˚
25° 40˚
30˚
10° x 40° 60˚
30˚
25˚
60˚
30° x 60°
100˚
5˚
30° x 60° x 5°
15
30° x 100°
Controls Controles Contrôles PRODUCT
DESCRIPTION
ITEM NO.
Kandi Touch
DMX 512 controller available in black or white
KND-TCH-B KND-TCH-W
Due to continuous improvements and innovations, specifications may change without notice. Please refer to our website for current technical data. These figures are provided as a guideline only and may vary with differing power supplies and installtions. All rights reserved. E&OE.
VDC20161411
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775 F: 702 407 7773 | www.modalight.com | © Copyright 2016
MODA GRAZE INTERIOR DMX I N S T A L L A T I O N 16
Accessories Accesorios Accessoires PRODUCT
DESCRIPTION
8 Pin 10’ Leader Cable Plug Gray
Power to first fixture of run
8 Pin 25’ Leader Cable Plug Gray
Power to first fixture of run
SIZE
ITEM NO.
Leader Cable:
Male Connector Dim:
L: 10’ (3.04m) W: 3/5” (18mm) H: 2/5” (11mm)
L: 1 9/10” (50mm) W: 7/10” (18mm) H: 1/2” (15mm)
Leader Cable:
Male Connector Dim:
L: 25’ (7.62m) W: 3/5” (18mm) H: 2/5” (11mm)
L: 1 9/10” (50mm) W: 7/10” (18mm) H: 1/2” (15mm)
MODA-COVE-GRAZEINTERIOR-8PIN-10FTLEADER-CABLE-G MODA-COVE-GRAZEINTERIOR-8PIN-25FTLEADER-CABLE-G
Jumper Cable:
L: 1’ (305mm) 8 Pin 1’ Jumper Cable Plug Gray
Allows longer connection between fixtures
Male Connector Dim:
Female Connector Dim:
L: 1 9/10” (50mm) W: 7/10” (18mm) H: 1/2” (15mm)
L: 1 4/5” (48mm) W: 7/10” (18mm) H: 3/5” (16mm)
MODA-COVE-GRAZEINTERIOR-8PIN-1FTJUMPER-CABLE-G
Jumper Cable:
L: 4’ (1,219mm) 8 Pin 4’ Jumper Cable Plug Gray
Allows longer connection between fixtures
Terminator Gray
Must be fixed to last fixture for safety
Optics
Available in different beam angles
Bracket Lock
Prevents sliding for vertical applications
L: 9/10” (24mm) W: 3/5” (16mm) H: 1/5” (5mm)
DMX 512 Splitter
Multi Run DMX Wiring
L: 18 9/10” (482mm) W: 5 4/5” (148mm) H: 1 2/5” (37mm)
500’ Belden 9841 Cable
RS-485 Cable for DMX
L: 500’ (152.4m)
1000’ Belden 9841 Cable
RS-485 Cable for DMX
Male Connector Dim:
Female Connector Dim:
L: 1 9/10” (50mm) W: 7/10” (18mm) H: 1/2” (15mm)
L: 1 4/5” (48mm) W: 7/10” (18mm) H: 3/5” (16mm)
Product Dim:
L: 1 7/10” (43mm) W: 1 1/10” (27mm) H: 3/5” (15mm)
MODA-COVE-GRAZEINTERIOR-8PIN-4FTJUMPER-CABLE-G
MODA-COVE-GRAZEINTERIOR-8PINTERMINATOR-G
Beam Angles:
·6 ° ·10° ·25°
·40° ·10° x 40° ·30° x 60°
·30° x 100° ·30° x 60° x 5°
Product Dim:
MODA-GRAZE-OPTICS
MODA-COVE-GRAZEINTERIOR-BRACKETLOCK-G
Product Dim:
Due to continuous improvements and innovations, specifications may change without notice. Please refer to our website for current technical data. These figures are provided as a guideline only and may vary with differing power supplies and installtions. All rights reserved. E&OE.
Product Dim:
Product Dim:
L: 1000’ (304.8m)
MODA-DMXSPLITTER-8
BDL-9841-500FT
BDL-9841-1000FT
VDC20161411
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775 F: 702 407 7773 | www.modalight.com | © Copyright 2016
MODA GRAZE INTERIOR DMX I N S T A L L A T I O N Do not attempt to install or use the product until installation is fully read and understood! !
No intente instalar o utilizar el producto sin antes leer y comprender las instrucciones! Ne tentez pas d’installer ou d’utiliser le produit jusqu’à ce que l’installation est entièrement lu et compris!
Do not use the product if lens or power cables are damaged! !
No utilize el producto si el lente o cables de energía están defectuosos! Ne pas utiliser le produit si l’objectif ou les câbles d’alimentation sont endommagés!
Do not use currents or voltages of any kind that do not fit under the product’s requirements! !
Por favor no utilice corrientes o voltajes que no sean los que se especifican para los productos! S’il vous plaît ne pas utiliser des courants ou des tensions autres que celles spécifiées pour la lampe! ! Make sure that power or cable is completely off or disconnected before connecting or disconnecting the product!
Por favor asegurese que el suministro de electricidad este apagado y cables estén desconectados antes de conectar o desconectar los productos! Faire S’il vous plaît assurer que l’alimentation et les câbles d’électricité sont hors tension et débranché avant de brancher ou de débrancher lampes! ! Fixtures must be programmed by MODA prior to shipping! Accesorios deben ser programadas por MODA antes de su envío! Les luminaires doivent être programmées par MODA avant l’expédition! !
Fixtures must be installed in correct order!
Lámparas se deben instalar en el orden correcto! Les luminaires doivent être installés dans le bon ordre!
Data and Power must be run in separate conduit! !
De datos y de alimentación se deben ejecutar en un conducto separado! Les données et la puissance doivent être exécutées dans un conduit séparé!
!
! If a fixture is not working, please remove from service. Si un accesorio no está funcionando, por favor poner fuera de servicio. Si un appareil ne fonctionne pas, s’il vous plaît retirer du service.
Do not coat the product in paint! This will ruin the product and void warranty! !
No cubra el producto en pintura! Esto va a arruinar el producto y anular la garantía! Ne pas enduire le produit dans la peinture! Cela va ruiner le produit et annuler la garantie!
Please make sure to install in accordance with the local code! !
Por favor asegúrese de instalar de acuerdo con el código local! Faire S’il vous plaît veillez à installer en conformité avec le code local! !
Use electrical tape to cover any exposed wires!
Lámparas debe ser programado por MODA antes de ser enviadas! Lampe doit être programmé par MODA avant qu’ils soient expédiés!
No serviceable parts - Do not disassemble.
No hay piezas reparables - No desamblar. Aucune pièce - Ne pas démonter. !
Do not hot swap fixtures!
No remplaze el producto mientras estén calientes! Feds ne cherchez pas produit tout chaud!
Do not open fixtures as they are line voltage and could cause a shock. !
No intente abrir el producto ya que contienen lineas de voltaje y podría causar un corto circuito. Ne pas essayer d’ouvrir le produit car ils contiennent des lignes de tension pordría et provoquer un court-circuit. !
Must use terminator.
Se tiene que utilizar terminadores. Doit utiliser terminateur. !
!
Must use Belden 9841cable for data connection.
Se debe utilizar cable Belden 9841 para conexión de data. Doit utiliser Belden 9841 câble pour les données connexion.
Do not stare into beam.
No mire fijamente la luz. Ne pas regarder le faisceau.
All MODA LIGHT products should be installed by a Licensed Electrician to local & national code. Do not modify, adapt or cut any MODA LIGHT components, plugs or accessories. Any modifications will void the warranty and may create a potential safety hazard. Do not put on the same circuit as inductive loads. Incorrect wiring will result in irreparable permanent damage to the LEDs and fixture. MODA LIGHT tests all products before shipping, and will not replace items that have been destroyed by incorrect wiring or handling. Ensure electrical circuit is switched off before wiring. See MODA LIGHT terms and conditions for product limited warranty. E&OE VDC20161411
© Copyright 2 016 • 955 W hite D riv e , La s Ve g a s , N V 8 9 1 1 9 • T: 7 0 2 4 0 7 7 7 7 5 • F: 7 0 2 4 0 7 7 7 7 3 • www. mod a lig ht. com
