Transcript
AIR COMPRESSOR and AIRBRUSH KIT MODEL | AB-KIT
Product Specifications Compressor: 1/8 HP 40 psi Sealed self lubricating bearings Oil free maintenance Sealed self lubricating bearings
Double Action Air Brush Gun Gravity fed operation Volt/Hz 110/60 50db at 40 inch
The AB-KIT is a maintenance-free compressor. It is completely sealed and requires no oiling. Make sure the Power Switch of the tool is in its “OFF” position and that the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. Always unplug compressor when not in use. For technical questions or replacement parts please call 1-866-418-9001.
Fat Daddio’s | PO BOX 30127 | Spokane, WA 99223 | www.fatdaddios.com
8 10 11
9
2
12 13 14
15
16
17
1
3
4
5
6
7
21
22
24
23
25
26
27
28
8
1
2
4
9 10
3
19 20
24
5
18
19
20
25
18
6 7 11
13
12
14
15
16
21
26 27
22 29
23
28
A
17
1. Needle Cover 2. Nozzle Cap 3. Nozzle 4. O-Ring for Nozzle Cap 5. Needle 6. O-Ring for Needle Guide 7. Needle Guide 8. Color Cup and Lid 9. Trigger 10. Trigger Guide 11. Stopper 12. Needle Chucking Guide 13. Spring 14. Spring Case 15. Needle Chucking Nut 16. Handle 17. Adjusting Screw 18. Guide Screw 19. Trigger Guide O-Ring 20. Valve O-Ring 21. Valve Body 22. Valve Rod O-Ring 23. Valve Rod 24. Valve Spring 25. Valve Screw 26. Hose Connector for Nut 27. O-Ring for Hose Connector 28. Hose Connector 29. Nozzle Spanner
B
I
C
H
D
A. Carrying handle B. Air Flow Valve C. Air Regulator D. Hose E. Air Brush Gun F. Adjusting Wrench G. Eye Dropper for thinning and cleaning solutions H. Power Cord I. On/Off switch
G F
E
Fat Daddio’s | PO BOX 30127 | Spokane, WA 99223 | www.fatdaddios.com
Use and care instructions: 1. Thin coloring product appropriately then pour into the Color Cup (part #8). Lid is held in place with friction and not threading. 2. Turn ON the Power Switch (I) and the Air Compressor will start and work continuously until it reaches its maximum preset pressure at which time it will automatically shut down. It will re-start when the pressure drops. 3. Holding the airbrush (part E) lightly in your hand, press the trigger (part #9) to activate air flow and color atomization. 4. Adjust the spray volume by moving the trigger front to back. When you have the correct spray volume, you may fix the position using the Adjustment Screw (part #17). 5. The spray pattern and color is controlled by the distance between the airbrush and work surface. For extra fine spray, remove the needle cover (part #1) and hold the airbrush closer to the work surface. NOTE: If any fluid blocks the Nozzle (part #3) from working, move the Needle Chucking Guide (part #12) back and forth. If this method does not clear the nozzle try loosening the Needle Adjustment Screw (part #17). This will allow a longer movement for the Needle (part #5) and allow the blocked fluid to escape, clearing the nozzle. CLEANING: Many coloring products used with airbrush systems are fast drying by design and can damage your airbrush gun if they are NOT flushed immediately. Empty the color cup and wash with water or a 50:50 vinegar and water solution. The airbrush gun should be cleaned by running the 50:50 solution through the color cup of the gun. Refill cup with water or 50:50 solution, then block the needle cover with a finger and spray. The air flows backward into the nozzle to clean the remaining color from the airbrush. Clean your airbrush gun before your first use and after each subsequent use to prevent any color build up.
Frequently Asked Questions (FAQ)
Why does my compressor turn on and then shuts down after a few seconds? This is normal! The compressor will automatically “turn-off ” when it is fully pressurized. Spraying the airbrush gun releases air and will soon turn the compressor back on to re-pressurize. The air flow is too weak or too strong. Your air compressor has an adjustable regulator to control air pressure (part C). To allow for greater air pressure from your compressor, lift the air flow valve (part B), and turn the dial clockwise to increase or counter-clockwise to decrease the pressure. The color does not spray out of the gun. Pull back on the operating lever (part #9) to control the color flow. If this does not work, you need to adjust the position of the needle. Adjust the needle unscrewing the black plastic handle (part #16). Unscrew the Needle Chucking Nut (part #15) to allow for the needle adjustment. The needle should NOT be pushed all the way to the front of the gun. This causes the color to be blocked from flowing. Slightly pulling the needle back and re-tightening will allow better color flow. When I operate my air gun, the color seems to splatter instead of blowing a fine mist. Clean your airbrush. You may have dirt or sediment blocking the air and color flow. If this does not work, completely remove the needle (part #5) and inspect to ensure the point is not bent. Replacement needles are available at your local retailer. Can I use my airbrush gun for both food and non-food applications? For safety reasons we recommended that you use separate guns for food and non-food applications.
Fat Daddio’s | PO BOX 30127 | Spokane, WA 99223 | www.fatdaddios.com
Troubleshooting Compressor and Airbrush Problem
Possible Causes
Probable Solutions
Air Compressor will not start.
No power at outlet. Cord not connected.
Check power at outlet. Check that cord is plugged in.
Pressure is low causing a weak spray at Nozzle of Air Brush.
Air connection is leaking. Air Hose is broken.
Replace Air Hose or Air Hose Connections.
Poor atomization when using Air Brush.
The coloring viscosity is too thick. The Air Brush nozzle is plugged or dirty. The air connection is leaking.
Check all air connections and make sure they are “air-tight”. Add correct thinning solution for type of coloring product you are using and mix thoroughly. Wash or replace the Air Brush nozzle.
90 Day Limited Warranty Fat Daddio’s professional airbrush system is protected by a limited 90 day warranty on any electrical failure, defects in material, design, or workmanship when used during normal use and as intended. For warranty questions or claims contact: Fat Daddio’s customer service at 866-418-9001 or by email at
[email protected] Mailed inquiries should be referred to: Fat Daddios PO Box 30175 Spokane WA 99223 Fat Daddio’s reserves the right to replace or refund the purchase price of the product at its discretion. Please provide your name, address, phone number, email, product number and the place of purchase. All returns or exchanges will be issued a Return Order Number to use when returning product to Fat Daddio’s. Product returned to Fat Daddio’s must be properly packaged and the postage charges prepaid using a shipping method that provides tracking and delivery information. All refunds or replacements will be processed within 10 business days of receiving the returned product. This warranty gives you specific legal rights. You may have other rights which vary from State to State.
IMPORTANT SAFETY INSTRUCTION IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT IN SERIOUS INJURY AND PROPERTY DAMAGE. RISK OF FIRE DO NOT SPRAY COMBUSTIBLE OR FLAMMABLE LIQUID IN A CONFINED AREA - SPRAY AREA MUST BE WELL VENTILATED. DO NOT SMOKE WHILE SPRAYING OR SPRAY WHERE SPARK OR FLAME IS PRESENT. KEEP COMPRESSOR AT LEAST 12 - 18 INCHES AWAY FROM SPRAYING AREA AND ALL EXPLOSIVE VAPORS. RISK OF ELECTRICAL SHOCK DO NOT EXPOSE COMPRESSOR TO RAIN OR OPERATE IN A WET AREA. NEVER USE THE AIR COMPRESSOR WITHOUT CONNECTION TO A PROPERLY GROUNDED OUTLET WITH THE SPECIFIED VOLTAGE AND FUSE PROTECTION. IMPROPER GROUNDING CAN RESULT IN ELECTRICAL SHOCK
Thank you for choosing Fat Daddio’s. We welcome any questions or comments you may have. Call 866-418-9001 or email us at
[email protected] for a prompt reply!
