Model Pf350-s Strip Nailer Operating Manual And

Transcript

P MODEL PF350-S Strip Nailer IMPORTANT! OPERATING MANUAL AND SCHEMATIC DO NOT DESTROY It is the customer s responsibility to have all operators and service personnel read and understand this manual. PRINTED IN U.S.A. © 2010, Illinois Tool Works, Inc. 502194-11 11/10 04/10 1 PF350-S FEATURES & BENEFITS Powerful Motor Tool Less Depth of Drive Compact Design Provides precise control of nail depth without adjusting the compressor. (on other side) Consistently drives into all engineered lumber. Able to get into tight spots Metal Exhaust Cap For maximun durability. Agressive Work Contact Grabs the wood when toe nailing. Light Weight Design Easy to manuever with less arm fatigue. Lock Out Eliminates blank firing. Bypass Follower Switchable Trigger For fast 2-step loading. Switches from sequential to bounce fire. Rafter Hook Conveniently stowes the tool. Rear Load Magazine Holds 2 strips or 84 nails. 9 PF350-S, 502000 PARTS LEGEND 1 * 2 3 4 * 5 6 * 7 * 8 9 * 10 11 12 13 * 14 15 16 17 ■ * 18 * 19 20 * 21 * 22 23 24 25 26 27 ➔ 28 29 30 * 31 32 33 34 35 36 37 38 39 40 • * ** ▲ ■ AIR CONSUMPTION - SCF/FASTENER •➔ 502004 502062 501299 502003 502013 123984 502859 211664 502434 198028 502032 502056 501300 502011 502012 502009 502010 501218 092235 502007 401985 500866 500729 502022 502807 502019 502021 511118 502031 502020 502026 502025 403796 502017 502058 502038 502016 502029 502034 404325 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 3 2 1 1 2 1 1 2 Air Deflector Air De ector Gasket S.H.C.S. 1/4-20 x 1” Top Cap Top Cap Gasket Valve Spring O-Ring O-Ring Poppet Assembly O-Ring REMOVED Exhaust Seal S.H.C.S.1/4-20 x 1-1/4” Piston Seal Piston Sleeve Check Band Driver Blade O-Ring Bulkhead O-Ring Bumper 41 42 43 44 45 46 47 ▲ 48 49 50 51 * 52 * 53 54 55 56 * 57 58 59 60 * 61 * 62 **63 64 65 66 67 * 68 69 70 71 72 ▲73 74 * 75 76 77 78 79 80 Driver Blade Seal REMOVED Magazine Assembly Follower Claw Lockout Bar Follower Body B.H.C.S. #8-32 x 1/2” Follower Spring Negator Spring Drum Pin Assembly Roll Pin 1/8” x 1-1/4” B.H.C.S. 1/4-20 x 3/4” Magazine Logo Label B.H.C.S. #8-32 x 1 REMOVED Magazine End Cap Housing Label Left Locknut #8-32 Denotes Normal Wear Items. Make sure Warning Label (502192) is properly affixed. Replace if necessary. Label available at no charge through the Service Parts Dept. Apply Loctite® 242 (Blue) Part No. 093500 A pply Loctite ® 620 (Green) Part No. 401491 A pply Loctite ® 271 (Red) Part No. 093422 Denotes New Change 502047 502046 502049 502061 404361 502050 502055 009016 095417 502006 502014 502042 091866 502053 502040 502060 092747 502035 502043 502041 1015358 196345 502192 502033 502446 502059 502044 197913 502002 502914 502930 502916 444786 442681 417147 502005 501300 502193 502036 502723 1 1 1 1 1 1 1 4 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 1 1 1 Lower W.C.E. Upper W.C.E. Detent Ball Detent Spring Roll Pin 1/8” x 1/2” Detent Body W.C.E. Spring S.H.C.S. 5/16-18 x 1” with Patch Lock Washer 5/16 Nose Magazine Isolator O-Ring Roll Pin 1/8” x 3/4” Dual Mode Trigger Trip Lever Trigger Spring O-Ring Housing Label Right Lower Valve Spool Trigger Pivot Pin O-Ring O-Ring Warning Label W.C.E. Guide Block Valve Pin with O-Rings Valve Pin Spring Upper Valve Spool O-Ring Housing with Grip Rafter Hook Rafter Hook Spring Rafter Hook Washer S.H.C.S. 1/4-20 x 5/8” Locknut 1/4-20 O-Ring Housing End Plug S.H.C.S. 1/4-20 x 1-1/4” Actuation Setting Label Thumb Wheel Roll Pin 3/8”x1-1/4” SAFETY INSTRUCTIONS WEAR EYE AND HEARING PROTECTION Always wear hearing protection and eye protection devices, including side shields when operating or working in the vicinity of a tool. DO NOT EXCEED MAXIMUM RECOMMENDED AIR PRESSURE .098 Operate the tool using only the recommended air pressure. Do not exceed the maximum air pressure marked on the tool. Be sure the air pressure gauge is operating properly and check it at least twice a day. SCF Never use any bottled air or gases such as oxygen to operate the tool since they could cause the tool to explode. AIR PRESSURE - PSIG 10 PF350-S 502000 120 71 74 15 2 76 77 58 14* 39 18 3 75 160 73 120 3 120 120 70 Piston Assembly #502008 1 72 68 69 250 4 64 16 49 5 80 60 50 33 67 62 61 59 66 65 57 Trigger Valve Assembly #502908 33 48 ➔ 17 6 325 Note: Install check band with thick side down. 8 20 45 9 10 12 42 21 44 43 22 13 120 25 51 46 19 7 56 47 53 54 Upper Work Contact Assembly #502734 79 23 41 40 15 63 78 35 36 26 27 28 34 33 32 29 #502435 52 29 Torque Values IN/LBS Trigger 55 Assembly 15 30 31 11 * Seal must be installed in this position. 38