Module No. 5056

Transcript

Module No. 5056 Getting Acquainted Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to read this manual carefully. • Be sure to keep all user documentation handy for future reference. Warning! • The measurement functions built into this watch are not intended for use in taking measurements that require professional or industrial precision. Values produced by this watch should be considered as reasonably accurate representations only. • When fishing, always take proper precautions to ensure your own personal safety and the personal safety of others around you. • The fishing level indicator and moon phase indicator produced by this watch are all based on calculations that use the watch’s current time, date, and Home Site settings. Because of this, you should make sure that the current date and time, and your Home Site data are all correct before using the indicators. E Warning! • See the “Timekeeping” section of this manual for information about setting the current time and date, and about specifying your Home Site. • Note that the fishing level indicator and moon phase indicator are all based on calculated values. They are provided only for reference purposes. Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss suffered by you or any third party arising through the use of this product or its malfunction. E-1 About This Manual (Light) E-2 • Button operations are indicated using the letters shown in the illustration. • For the sake of simplicity, the sample displays in this manual do not show the analog hands of the watch. • Each section of this manual provides you with the information you need to perform operations in each mode. Further details and technical information can be found in the “Reference” section. • To ensure that this watch provides you with the years of service for which it is designed, be sure to carefully read and follow the instructions under “Operating Precautions” and “User Maintenance.” Contents General Guide ......................................................................................................... E-6 Timekeeping ............................................................................................................ E-8 Fishing Mode ......................................................................................................... E-18 Thermometer ......................................................................................................... E-24 Stopwatch .............................................................................................................. E-30 Countdown Timer .................................................................................................. E-32 Alarm ...................................................................................................................... E-36 World Time ............................................................................................................. E-39 Illumination ............................................................................................................ E-41 Reference .............................................................................................................. E-42 Specifications ....................................................................................................... E-52 Operating Precautions ......................................................................................... E-55 User Maintenance ................................................................................................. E-64 E-3 Procedure Lookup The following is a handy reference list of all the operational procedures contained in this manual. To set the digital time and date ........................................................................... E-10 To toggle the Timekeeping Mode digital time between DST and Standard Time ................................................................... E-13 To configure Home Site data ............................................................................... E-15 To adjust the analog time ..................................................................................... E-17 To view the current fishing level and Moon data ............................................... E-21 To specify a date ................................................................................................... E-23 To recall temperature records ............................................................................. E-29 To measure times with the stopwatch ................................................................ E-31 To use the countdown timer ................................................................................ E-33 To configure countdown start time and auto-repeat settings .......................... E-34 E-4 To set the alarm time ............................................................................................ E-37 To test the alarm ................................................................................................... E-37 To turn the Daily alarm and the Hourly Time Signal on and off ........................ E-38 To view the time in another city ........................................................................... E-40 To toggle a city code time between Standard Time and Daylight Saving Time ............................................................................... E-40 To turn on illumination manually ......................................................................... E-41 To calibrate the temperature sensor ................................................................... E-46 To specify the temperature display unit ............................................................. E-47 To turn the button operation tone on and off ..................................................... E-48 E-5 General Guide • Press C to change from mode to mode. • In any mode (except when a setting screen is on the display), press B to illuminate the display. Fishing Mode Press C. ▲ Timekeeping Mode E-6 ▲ ▲ Hand Setting Mode Temperature Data Recall Mode Stopwatch Mode ▲ ▲ Countdown Timer Mode Alarm Mode ▲ ▲ ▲ World Time Mode E-7 Timekeeping Use the Timekeeping Mode to set and view the current time and date. This watch features separate digital and analog timekeeping. The procedures for setting the digital time (page E-10) and analog time (page E-17) are different. • In the Timekeeping Mode, press A to toggle between the thermometer screen and the temperature tendency screen. Temperature Tendency Thermometer Screen Screen Temperature Moon phase indicator Day of week – Day Temperature tendency graph ▲ ▲ Press A. Seconds PM indicator Hour : Minutes Fishing level indicator • The fishing level indicator indicates the times when fish can be expected to be feeding. For more information, see “Fishing Mode” (page E-18). E-8 • The Moon phase indicator (page E-42) shows the current Moon phase in accordance with the current date as kept in the Timekeeping Mode. • See “Thermometer” (page E-24) for details about the thermometer screen and temperature tendency graph. Important! • Be sure to configure the current time and date, and your Home Site data (data for the site where you use the watch) correctly before using the functions of this watch. See “Home Site Data” (page E-14) for more information. Setting the Digital Time and Date This watch is preset with UTC differential values that represent each time zone around the globe. Before setting the digital time, be sure to first set the UTC differential for your Home Site, which is the location where you normally will be using the watch. • Note that World Time Mode times (page E-39) are all displayed based on the time and date settings you configure in the Timekeeping Mode. E-9 lll lll To set the digital time and date 1. In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting screen. • Be sure to configure the correct UTC differential for l ll your Home Site before configuring any other Timekeeping Mode settings. • See the “City Code List” at the back of this manual for information about the UTC differential settings that are supported. Seconds 2. Press C to move the flashing in the sequence shown below to select the setting you want. ll Seconds Temperature Unit E-10 DST UTC Differential Temperature Sensor Calibration Hour Day Minutes Month 12/24-Hour Format Year 3. When the setting you want to change is flashing, use D and B to change it as described below. Screen: To do this: Do this: Reset the seconds to 00 Press D. Toggle between Daylight Saving Time (ON) and Standard Time (OF) Specify the UTC differential Press D. Change the hour or minutes Use D (+) and B (–). Use D (+) and B (–). Toggle between 12-hour (12H) and Press D. 24-hour (24H) timekeeping Use D (+) and B (–). Change the year, month, or day E-11 • The UTC differential setting range is –12.0 to +14.0 in 0.5-hour units for Standard Time (DST turned off), and –11.0 to +15.0 in 0.5-hour units for summer time (DST turned on). • For information about settings other than the time and date, see the following. Temperature Sensor Calibration: “Thermometer” (page E-45) Temperature Unit: “To specify the temperature display unit” (page E-47) 4. Press A twice to exit the setting screen. • The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is applied in all modes. • The day of the week is displayed automatically in accordance with the date (year, month, and day) settings. • See “Daylight Saving Time (DST) Setting” below for details about the DST setting. • Any time the seconds setting is changed, the analog hands are adjusted accordingly. Daylight Saving Time (DST) Setting Daylight Saving Time (summer time) advances the time setting by one hour from Standard Time. Remember that not all countries or even local areas use Daylight Saving Time. E-12 ll lll ll ll lll To toggle the Timekeeping Mode digital time between DST and Standard Time 1. In the Timekeeping Mode, hold down A until the On/Off status seconds start to flash, which indicates the setting screen. 2. Press C once and the DST setting screen appears. l ll 3. Press D to toggle between Daylight Saving Time (ON displayed) and Standard Time (OF displayed). lll 4. Press A twice to exit the setting screen. • The DST indicator appears on the Timekeeping, Fishing, Alarm, and Hand Setting Mode screens to indicate that DST indicator Daylight Saving Time is turned on. In the case of the Fishing Mode, the DST indicator appears on the fishing level screen only. lll E-13 Home Site Data Moon phase, the fishing level indicator, and Fishing Mode data will not be displayed properly unless Home Site data (UTC differential and longitude) is configured correctly. • The UTC differential is a value that indicates the time difference between a reference point in Greenwich, England and the time zone where a city is located. • The letters UTC is the abbreviation for Coordinated Universal Time, which is the world-wide scientific standard of timekeeping. It is based upon carefully maintained atomic (cesium) clocks that keep time accurately to within microseconds. Leap seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s rotation. • The “Site Data List” at the back of this manual provides UTC differential and longitude information around the world. • The following is the initial factory default Home Site data (Tokyo, Japan) when you first purchase the watch and whenever you have the batteries replaced. Change these settings to match the area where you normally use the watch. UTC differential (+9.0); Longitude (East 140 degrees) E-14 ll ll To configure Home Site data 1. In the Timekeeping Mode, hold down A until the Longitude seconds start to flash, which indicates the setting (east/west) screen. 2. Press C twice to display the UTC differential setting screen, and confirm that the setting is correct. • If the UTC differential setting is not correct, use D (+) and B (–) to change it. lll lll 3. Press A to display the longitude value setting screen. 4. Press C to toggle the flashing between the longitude value and the longitude unit (east/west). 5. While the setting you want to change is flashing, use Longitude D and B to change it as described below. value lll l ll E-15 Setting Screen Button Operations Longitude Value Use D (+) and B (–) to change the setting. • You can specify a value from 0° to 180°, in 1degree units. Longitude Unit (East/West) Use D to switch between east longitude ( ) and west longitude ( ). 6. Press A to exit the setting screen. Setting the Analog Time Perform the procedure below when the time indicated by the analog hands does not match the time of the digital display. E-16 To adjust the analog time ll ll lll lll 1. In the Timekeeping Mode, press C seven times to enter the Hand Setting Mode (page E-6). 2. Hold down A until the current digital time starts to flash, which indicates the setting screen. 3. Use D to adjust the analog setting. • Press D once to advance the hands 20 seconds. • Hold down D to advance the hands at high speed. lll l ll • To lock high speed hands movement, hold down D to start it and then press B to lock. The hands will continue to advance for one 12-hour cycle or until you press any button to stop it. It will also stop automatically after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal, or countdown beeper) starts to sound. 4. Press A to exit the setting screen. • The minute hand will be adjusted slightly to match the seconds when you exit the setting screen. • To return to the Timekeeping Mode, press C. E-17 Fishing Mode The Fishing Mode displays an indicator that shows, as one of five levels, the suitability of a specific date and time (minute 00 to minute 59 of a particular hour) for fishing. This mode also can be used to display Moon Data (Moon age and Moon phase) for a specific date. • If you suspect that the fishing level indicator or current Moon data is wrong for some reason, check the current Timekeeping Mode settings (time, date, and Home Site), and correct them if required. • See “Moon Phase Indicator” (page E-42) for information about the Moon phase indicator. • All of the operations in this section are performed in the FISH Fishing Mode, which you enter by pressing C (page indicator E-6). Month – Day Moon phase indicator Time Fishing level indicator Fishing Level Screen E-18 Fishing Level Indicator The fishing level indicator shows the relative favorability of a fishing time (calculated in accordance with Moon transit and phase) as shown in the table below. Level 5 Level 4 Level 3 Level 2 Level 1 E-19 Moon Transit Moon Phase New moon* Full moon First quarter Last quarter Other Upper Lower West East Other Level 5 Level 4 Level 3 Level 4 Level 3 Level 2 Level 3 Level 2 Level 1 * These indicators actually appear during Moon ages 13.0 to 16.6 (Full Moon and phase immediately preceding it) and 27.7 to 1.8 (New Moon and phase immediately preceding it). • The fishing level indicator changes in accordance with the Moon data. • In the Timekeeping Mode, the FISH indicator flashes whenever the fishing level of the current time is 4 or 5. E-20 To view the current fishing level and Moon data In the Fishing Mode, press A to toggle between the fishing level screen and the Moon Data screen. • The fishing level indicator shows the level for the displayed time. The initial fishing level screen shows the level for 6:00 a.m. The Moon data screen shows the Moon age and Moon phase for the current date. Fishing Level Screen Moon Data Screen Month – Day Month – Day Moon phase indicator Fishing level indicator Time ▲ ▲ Press A. Moon age • While the fishing level screen is displayed, press D to advance to the next hour. E-21 • While the Moon Data screen is displayed, press D to advance to the next day. • You can also specify a particular date (year, month, day) to view its fishing level and Moon data. See “To specify a date” (page E-23) for more information. • When you enter the Fishing Mode, the screen (fishing level or Moon data) that was displayed the last time you exited the mode appears first. E-22 To specify a date Month – Day ll ll lll lll 1. In the Fishing Mode, hold down A until the year setting starts to flash, which indicates the setting screen. 2. Press C to move the flashing in the sequence shown below to select the other settings. Year Month Day lll l ll Year 3. While a setting is flashing, use D (+) or B (–) to change it. • You can specify a date in the range of January 1, 2000 to December 31, 2099. 4. Press A to exit the setting screen. 5. Use A to display either the fishing level screen or the Moon Data screen. E-23 Thermometer This watch uses a temperature sensor to measure temperature. A reading is taken during each even-numbered minute, and the result of the last reading is displayed on the thermometer screen. The watch also takes separate readings and stores them in memory for display in the temperature tendency graph (page E-26), which can be viewed in the Timekeeping Mode. Measured temperature values are stored in memory for later recall when you need them (page E-28). Temperature Thermometer Screen Tendency Screen Temperature Temperature E-24 ▲ ▲ Press A. tendency graph • You can select either Celsius (°C) or Fahrenheit (°F) units for the thermometer screen. See “To specify the temperature display unit” (page E-47) for more information. • The thermometer screen displays temperature values in 0.1°C units (or 0.2°F units). • The display range of the thermometer screen is –10.0°C to 60.0°C (or 14.0°F to 140.0°F). • You can calibrate the temperature sensor if you feel that the displayed temperature values are not correct. See “Temperature Sensor Calibration” (page E-45) for more information. Important! • Temperature measurements are affected by your body temperature (while you are wearing the watch), direct sunlight, and moisture. To achieve a more accurate temperature measurement, remove the watch from your wrist, place it in a well ventilated location out of direct sunlight, and wipe all moisture from the case. It takes approximately 20 to 30 minutes for the case of the watch to reach the actual surrounding temperature. E-25 Temperature Tendency Graph The watch also takes temperature readings at the top and the bottom of each hour and stores the results in memory for display on the temperature tendency graph. Depending on the current Timekeeping Mode time, the temperature tendency graph shows either the top of the hour measurements or the bottom of the hour measurements for the past 17 hours. From the top of each hour to the 29th minute, past top of the hour readings are shown in the graph. From the bottom of each hour to the 59th minute, past bottom of the hour readings are shown in the graph. Temperature tendency graph contents are updated every 30 minutes. ▲ +6.0 to +9.9°C (+10.8 to +17.8°F) +2.0 to +5.9°C (+3.6 to +10.6°F) –1.9 to +1.9°C (–3.4 to +3.4°F) –5.9 to –2.0°C (–10.6 to –3.6°F) –9.9 to –6.0°C (–17.8 to –10.8°F) E-26 Past 17 hours of measurement values Latest measurement value The horizontal axis of the graph represents time. The rightmost column is the newest temperature value in memory, while the leftmost column is the temperature value stored approximately 17 hours ago (1 dot = 1 hour). The vertical axis of the graph represents the relative change from one hour to the next. • When the relative change from one hour to the next exceeds +10.0°C (+18.0°F), the dot at the highest point for the applicable hour flashes. • When the relative change from one hour to the next exceeds –10.0°C (–18.0°F), there is no dot in the applicable hour’s column. • If a measurement error occurs for some reason, only a single the dot in the center column will be displayed. Temperature change greater than +10.0°C (+18.0°F) Temperature change greater than –10.0°C (–18.0°F) Error E-27 Recalling Temperature Data The measurements the watch takes at the top and the bottom of each hour are stored in memory automatically. Memory can hold up to 50 measurement records. You can use the Temperature Data Recall Mode to recall memory data when you need it. • Each temperature data record has a number. The newest data record is number 01, while the oldest data record is the one with the highest number. • When there are already 50 records in memory, storage of a new temperature reading causes the oldest record (record number 50) to be deleted automatically to make room for the new data. The new data is assigned record number 1, and all of the numbers of all the other records (01 to 49) are incremented by 1 (becoming 02 through 50). E-28 To recall temperature records 1. In the Timekeeping Mode, press C twice to enter the Temperature Data Recall Mode. Temperature • This displays the newest record currently in memory. 2. Use D (+) to scroll through the records. • Pressing D while the oldest record is displayed will scroll to the newest record. • If a temperature measurement operation is performed while a record is displayed, the displayed record’s number will be incremented by 1. • If an error occurs during temperature measurement, ‘‘--.-’’ will be shown for the temperature value in the corresponding record. Data storage time Record number E-29 Stopwatch 1/100 second Hours E-30 Seconds Minutes The stopwatch lets you measure elapsed time, split times, and two finishes. • The display range of the stopwatch is 99 hours, 59 minutes, 59.99 seconds. • The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it. • All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C (page E-7). To measure times with the stopwatch Elapsed Time D Start ➤D Stop ➤D Re-start ➤D Stop ➤A Clear ➤A Split ➤A Split release ➤D Stop ➤A Clear ➤D Stop ➤A Split release ➤A Clear Split Time D Start (SPL displayed) Two Finishes D Start ➤A Split First runner finishes. Display time of first runner. Second runner finishes. Display time of second runner. E-31 Countdown Timer Seconds Hours E-32 Minutes You can set the countdown timer within a range of one minute to 100 hours. An alarm sounds when the countdown reaches zero. • You can also select auto-repeat, which automatically restarts the countdown from the original value you set whenever zero is reached. • All of the operations in this section are performed in the Countdown Timer Mode, which you enter by pressing C (page E-7). To use the countdown timer Press D while in the Countdown Timer Mode to start the countdown timer. • When the end of the countdown is reached and auto-repeat is turned off, the alarm sounds for 10 seconds or until you stop it by pressing any button. The countdown time is automatically reset to its starting value after the alarm stops. • When auto-repeat is turned on, the countdown will restart automatically without pausing when it reaches zero. The alarm sounds to signal when the countdown reaches zero. • The countdown timer measurement operation continues even if you exit the Countdown Timer Mode. • To stop a countdown operation completely, first pause it (by pressing D), and then press A. This returns the countdown time to its starting value. E-33 lll lll To configure countdown start time and auto-repeat settings 1. While the countdown start time is on the display in the Auto-repeat on indicator Countdown Timer Mode, hold down A until the hour setting of the countdown start time starts to flash, which indicates the setting screen. • If the countdown start time is not displayed, use the procedure under “To use the countdown timer” (page l ll E-33) to display it. 2. Press C to move the flashing in the sequence shown below, and select the setting you want to change. ll On/Off status Start Time (Hours) Start Time (Minutes) Auto-Repeat On/Off 3. Perform the following operations, depending on which setting is currently selected on the display. • While the start time setting is flashing, use D (+) and B (–) to change it. E-34 • Set 0:00 to specify 100 hours. • While the auto-repeat on/off setting (0N or 0F) is flashing on the display, press D to toggle auto-repeat on (0N) and off (0F). 4. Press A to exit the setting screen. • The auto-repeat on indicator ( ) is displayed on the Countdown Timer Mode screen while this function is turned on. • Frequent use of auto-repeat and the alarm can run down battery power. E-35 Alarm While the alarm is turned on, the watch beeps when the Alarm time (Hour : Minutes) alarm time is reached. You can also turn on an Hourly AM indicator Alarm on indicator E-36 Time Signal, which will cause the watch to beep twice every hour on the hour. • All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C (page E-7). Hourly time signal on indicator To set the alarm time lll lll 1. In the Alarm Mode, hold down A until the hour setting of the alarm time starts to flash, which indicates the setting screen. • This operation turns on the alarm automatically. l ll 2. Press C to move the flashing between the hour and minute settings. 3. While a setting is flashing, use D (+) and B (–) to change it. • When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (A indicator) or p.m. (P indicator). 4. Press A to exit the setting screen. ll Alarm Operation The alarm sounds at the preset time for 10 seconds, regardless of the mode the watch is in. • To stop the alarm tone after it starts to sound, press any button. To test the alarm In the Alarm Mode, hold down D to sound the alarm. E-37 To turn the Daily alarm and the Hourly Time Signal on and off In the Alarm Mode, press D to cycle through the settings shown below. Alarm Off Signal Off Alarm On Signal Off Alarm Off Signal On Alarm On Signal On • The alarm on indicator and the Hourly Time Signal on indicator are shown on the display in all modes while these functions are turned on. E-38 World Time The World Time Mode digitally displays the current time in 50 cities (30 time zones) around the world. • The times kept in the World Time Mode are synchronized with the time being kept in the Timekeeping Mode. If you feel that there is an error in any World Time Mode time, check the UTC differential of your Home Site Data (Home City) and the current setting of the Timekeeping Mode time. • Select a city code in the World Time Mode to display the current time in any particular time zone around the globe. See the “City Code List” at the back of this Current time in selected city manual for information about the UTC differential settings that are supported. Day of week and day in • All of the operations in this section are performed in the selected city World Time Mode, which you enter by pressing C (page E-7). City code E-39 To view the time in another city While in the World Time Mode, press D to scroll eastward through the city codes (time zones). To toggle a city code time between Standard Time and Daylight Saving Time 1. In the World Time Mode, use D to display the city code (time zone) whose Standard Time/Daylight Saving Time setting you want to change. 2. Hold down A to toggle between Daylight Saving Time (DST indicator displayed) and Standard Time (DST indicator not displayed). • The DST indicator is shown on the World Time screen while Daylight Saving Time is turned on. DST indicator • Note that changing the Daylight Saving Time for any city code causes the setting to be applied to all city codes. E-40 Illumination This watch has an EL (electro-luminescent) panel that causes the entire display to glow for easy reading in the dark. • See “Illumination Precautions” (page E-51) for other important information about using illumination. To turn on illumination In any mode (except when a setting screen is on the display), press B to illuminate the display for about one second. E-41 Reference This section contains more detailed and technical information about watch operation. It also contains important precautions and notes about the various features and functions of this watch. Moon Phase Indicator The Moon phase indicator of this watch indicates the current phase of the Moon as shown below. Moon phase indicator E-42 (part you cannot see) Moon phase (part you can see) Moon Phase Indicator Moon Age 0.0 - 1.8 27.7 - 29.5 1.9 - 5.5 5.6 - 9.2 9.3 - 12.9 13.0 - 16.6 16.7 - 20.2 20.3 - 23.9 24.0 - 27.6 Moon Phase New Moon First Quarter (Waxing) Full Moon Last Quarter (Waning) • The Moon phase indicator shows the Moon as viewed at noon from a position in the Northern Hemisphere looking south. Note that at times the image shown by the Moon phase indicator may differ from that of the actual Moon in your area. • The left-right orientation of the Moon phase is reversed when viewing from the Southern Hemisphere or from a point near the equator. E-43 Moon Phases and Moon Age The Moon goes through a regular 29.53-day cycle. During each cycle, the Moon appears to wax and wane as the relative positioning of the Earth, Moon, and Sun changes. The greater the angular distance between the Moon and the Sun,* the more we see illuminated. * The angle to the Moon in relation to the direction at which the Sun is visible from the Earth. This watch performs a rough calculation of the current Moon age starting from day 0 of the moon age cycle. Since this watch performs calculations using integer values only (no fractions), the margin for error of the displayed Moon age is ± 1 day. E-44 Thermometer Temperature Sensor Calibration The temperature sensor built into the watch is calibrated at the factory and normally requires no further adjustment. If you notice serious errors in the temperature readings produced by the watch, you can calibrate the sensor to correct the errors. Important! Incorrectly calibrating the temperature sensor can result in incorrect readings. Carefully read the following before doing anything. • Compare the readings produced by the watch with those of another reliable and accurate thermometer. • If adjustment is required, remove the watch from your wrist and wait for 20 or 30 minutes to give the temperature of the watch time to stabilize. E-45 lll lll To calibrate the temperature sensor 1. In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting screen. 2. Press C nine times to display the temperature sensor l ll calibration screen. 3. Use D (+) and B (–) to change the calibration value. • You can change the value in 0.1°C (0.2°F) steps, in a range of ±10°C (±18°F). The calibration value shows Calibration value ‘‘--.-’’ when the setting is outside the allowable range. ll • To return the calibration value to its default (no calibration, indicated by ‘‘- -’’), press D and B at the same time. • Temperature sensor calibration will not be possible if the current reading is outside the allowable display range (–10.0°C/14.0°F to 60.0°C/140.0°F) and the calibration value shows ‘‘- -’’. • Setting a sensor calibration value does not affect temperature values that are already stored in memory. 4. After configuring the setting you want, press A twice to exit the setting screen. E-46 lll lll To specify the temperature display unit 1. In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting screen. l ll 2. Press C 10 times to display the temperature unit setting screen. 3. Use D to switch between Celsius ( ) and Fahrenheit ( ). • The initial factory default and the initial default after Temperature unit battery replacement is Celsius ( ). ll 4. After configuring the setting you want, press A twice to exit the setting screen. • The temperature display unit setting you select is also applied to temperature values that are already stored in memory. E-47 Button Operation Tone The button operation tone sounds any time you press one of the watch’s buttons. You can turn the button operation tone on or off as desired. • Even if you turn off the button operation tone, the alarm, Hourly Time Signal, and Countdown Timer Mode alarm all operate normally. Mute indicator To turn the button operation tone on and off In any mode (except when a setting screen is on the display), hold down C to toggle the button operation tone on (mute indicator not displayed) and off (mute indicator displayed). • Since the C button is also the mode change button, holding it down to turn the button operation tone on or off also causes the watch’s current mode to change. • The mute indicator is displayed in all modes when the button operation tone is turned off. E-48 Auto Return Feature • If you leave a screen with flashing digits on the display without performing any operation for two or three minutes, the watch saves any settings you have made up to that point and exits the setting screen automatically. • The watch will change to the Timekeeping Mode automatically if you do not perform any operation in the Fishing Mode, Temperature Data Recall Mode, Alarm Mode, or Hand Setting Mode for two or three minutes. Scrolling The B and D buttons are used in various modes and setting screens to scroll through data on the display. In most cases, holding down these buttons during a scroll operation scrolls through the data at high speed. Timekeeping • Resetting the seconds to 00 while the current count is in the range of 30 to 59 causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are reset to 00 without changing the minutes. E-49 • With the 12-hour format, the P (PM) indicator appears on the display for times in the range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range of midnight to 11:59 a.m. • With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without any indicator. • The year can be set in the range of 2000 to 2099. • The watch’s built-in full automatic calendar makes allowances for different month lengths and leap years. Once you set the date, there should be no reason to change it except after you have the watch’s batteries replaced. World Time • The seconds count of the World Time is synchronized with the seconds count of the Timekeeping Mode. • All World Time Mode times are calculated from the current time in the Timekeeping Mode using UTC time differential values. E-50 Illumination Precautions • The electro-luminescent panel that provides illumination loses power after very long use. • Illumination may be hard to see when viewed under direct sunlight. • The watch may emit an audible sound whenever the display is illuminated. This is due to vibration of the EL panel used for illumination, and does not indicate malfunction. • Illumination turns off automatically whenever an alarm sounds. • Frequent use of illumination runs down the batteries. E-51 Specifications Accuracy at normal temperature: ± 30 seconds a month Digital Timekeeping: Hour, minutes, seconds, a.m. (A)/p.m. (P), day, day of the week Time format: 12-hour and 24-hour Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099 Other: Daylight Saving Time (summer time)/Standard Time; Home Site data settings (UTC differential and longitude) Analog Timekeeping: Hour, minutes (hand moves every 20 seconds) Fishing Mode: Fishing level for a specified date and time; Moon phase indicator and Moon age for a specified date Thermometer: Measurement and display range: –10.0°C to 60.0°C (or 14.0°F to 140.0°F) Display unit: 0.1°C (or 0.2°F) Thermometer measurement timing: During each even-numbered minute Memory measurement timing: At the top and the bottom of each hour Memory capacity: Up to 50 sets of data (time, temperature) Temperature sensor precision: ± 2°C (± 3.6°F) E-52 Other: Thermometer/temperature tendency graph switching in the Timekeeping Mode; Temperature unit switching (°C/°F); Temperature sensor calibration (Range: ±10°C/±18°F and unit: 0.1°C/0.2°F) Stopwatch: Measuring unit: 1/100 second Measuring capacity: 99:59' 59.99'' Measuring modes: Elapsed time, split time, two finishes Countdown Timer: Measuring unit: 1 second Input range: 1 minute to 100 hours (1-minute increments and 1-hour increments) Other: Auto-repeat timing Alarm: Daily alarm; Hourly Time Signal World Time: 50 cities (30 time zones) Other: Standard time/Daylight Saving Time Illumination: EL (electro-luminescent panel) Other: Button operation tone on/off E-53 Battery: Two silver oxide batteries (Type: SR927W) Approximately 2 years on type SR927W (assuming alarm operation 10 seconds per day, one illumination operation 1.5 seconds per day, and temperature measurement every 2 minutes) Frequent use of illumination shortens the battery life. E-54 Operating Precautions Water Resistance • The following applies to watches with WATER RESIST or WATER RESISTANT marked on the back cover. Enhanced Water Resistance Under Water Resistance Daily Use Under Daily 5 10 20 Use Atmospheres Atmospheres Atmospheres On watch front or on back cover Hand washing, rain Example of Water-related work, swimming Daily Use Windsurfing Skin diving Marking No BAR mark Yes No No No 5BAR 10BAR 20BAR Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes • Do not use this watch for scuba diving or other types of diving that requires air tanks. E-55 • Watches that do not have WATER RESIST or WATER RESISTANT marked on the back cover are not protected against the effects of sweat. Avoid using such a watch under conditions where it will be exposed to large amounts of sweat or moisture, or to direct splashing with water. • Even if a watch is water-resistant, do not operate its buttons or crown while it is submersed in water or wet. • Even if a watch is water-resistant, avoid wearing it in the bath or in areas where detergents (soap, shampoo, etc.) are being used. Such conditions can reduce water resistance. • After submersion in seawater, use plain water to rinse all salt and dirt from the watch. • In order to maintain water resistance, have the gaskets of your watch replace periodically (about once every two or three years). • A trained technician will know how to check your watch for proper water resistance whenever you have its battery replaced. Battery replacement requires the use of special tools. Always request battery replacement from your original retailer or from an authorized CASIO Service Center. • Some water-resistant watches come with fashionable leather bands. Avoid swimming, washing, or any other activity that causes direct exposure of a leather band to water. E-56 • The inside surface of the watch glass may fog when the watch is exposed to a sudden drop in temperature. No problem is indicated if the fogging clears up relatively quickly. If the fogging does not clear or if water has gotten into the watch, take the watch in for repair immediately. • Continued use of the watch with water inside can result in damage to electronic and mechanical components, the face of the watch, etc. Band • Tightening the band too tightly can cause you to sweat and make it hard for air to pass under the band, which can lead to skin irritation. Do not fasten the band too tightly. There should be enough room between the band and your wrist so you can insert your finger. • Deterioration, rust, or corrosion of the band can cause it to break, which may result in the watch falling off your wrist and becoming lost. Be sure to take good care of the band and keep it clean. Should you notice any breakage, discoloration, looseness or other problem with the band, immediately contact your original retailer or an authorized CASIO Service Center to have it checked, repaired, or replaced. Note that you will be charged for any repair or replacement of the band. E-57 Temperature • Never leave the watch on the dashboard of a car, near a heater, or in any other location that is subject to very high temperatures. Do not leave the watch where it will be exposed to very low temperatures, either. Temperature extremes can cause the watch to lose or gain time, to stop, or otherwise malfunction. • Leaving the watch in an area hotter than +60°C (140°F) for long periods can lead to problems with its LCD. The LCD may become difficult to read at temperatures lower than 0°C (32°F) and greater than +40°C (104°F). Impact • Your watch is designed to withstand impact incurred during normal daily use and light activity such as playing catch, tennis, etc. Dropping the watch or otherwise subjecting it to strong impact, however, can lead to malfunction. Note that watches with shock-resistant designs (G-SHOCK, Baby-G, G-ms) can be worn while operating a chain saw or engaging in other activities that generate strong vibration, or while engage in strenuous sports activities (motocross, etc.). E-58 Magnetism • The hands of analog and combination (analog-digital) watches are moved by a motor that uses magnetic force. When such a watch is close to a device (audio speakers, magnetic necklace, cell phone, etc.) that emits strong magnetism, the magnetism can cause timekeeping to slow down, speed up, or stop, resulting in the incorrect time being displayed. Electrostatic Charge • Exposure to very strong electrostatic charge can cause the watch to display the wrong time. Very strong electrostatic charge even can damage electronic components. • Electrostatic charge can cause the display to go blank momentarily or cause a rainbow effect on the display. E-59 Chemicals • Do not allow the watch to come into contact with thinner, gasoline, solvents, oils, or fats, or with any cleaners, adhesives, paints, medicines, or cosmetics that contain such ingredients. Doing so can cause discoloration of or damage to the case, resin band, leather band, and other parts. Storage • If you do not plan to use the watch for a long time, wipe it thoroughly free of all dirt, sweat, and moisture, and store it in a cool, dry place. Resin Components • Allowing the watch to remain in contact with other items or storing it together with other items for long periods while it is wet can cause the color of the other items to transfer to the resin components of the watch. Be sure to dry off the watch thoroughly before storing it and make sure it is not in contact with other items. • Leaving the watch where it is exposed to direct sunlight (ultraviolet rays) for long periods or failure to clean dirt from the watch for long periods can cause it to become discolored. E-60 • Friction caused by certain conditions (frequent external force, sustained rubbing, impact, etc.) can cause discoloration of painted components. • If there are printed figures on the band, strong rubbing of the printed area can cause discoloration. • Failure to clean dirt from the watch for long periods can cause fluorescent color to fade. Wash dirt off with water as soon as possible and then dry the watch. • Semi-transparent resin parts can become discolored due to sweat and dirt, and if exposed to high temperatures for long periods. • Contact an authorized CASIO Service Center to have resin components replaced. Note that you will be charged for replacement costs. Natural Leather and Imitation Leather Bands • Allowing the watch to remain in contact with other items or storing it together with other items while it is wet for long periods can cause the color of the other items to transfer to the natural leather or imitation leather band of the watch. Be sure to dry off the watch thoroughly before storing it and make sure it is not in contact with other items. E-61 • Leaving a leather band where it is exposed to direct sunlight (ultraviolet rays) for long periods or failure to clean dirt from a leather band for long periods can cause it to become discolored. Important! • Subjecting a natural leather or imitation leather band to rubbing or dirt can cause color transfer and discoloration. Metal Components • Failure to clean dirt from a metal band can lead to formation of rust, even if the band is stainless steel or plated. If the watch is exposed to sweat or water, wipe it thoroughly with a soft, absorbent cloth and then store it in a well-ventilated location to dry. • To clean the band, use a soft toothbrush or similar tool to scrub it with a weak solution of water and a mild neutral detergent. Take care to avoid getting solution on the watch case. E-62 Bacteria and Odor Resistant Band • The bacteria and odor resistant band protects against odor generated by the formation of bacteria from sweat, which ensures good comfort and hygiene. In order to ensure maximum bacteria and odor resistance, keep the band clean. Use an absorbent soft cloth to wipe the band clean of dirt, sweat, and moisture. The bacteria and odor resistant band suppresses the formation of organisms and bacteria. It does not protect against rash due to allergic reaction, etc. Display • Display figures may be difficult to read when viewed from an angle. Sensors • The sensors of this watch are precision instruments. Never try to take them apart. Never try to insert any objects into the openings of sensors, and take care to ensure that dirt, dust, or other foreign matter does not get into sensors. After using the watch where it is immersed in saltwater, rinse it thoroughly with fresh water. E-63 User Maintenance Caring for Your Watch • A dirty or rusty case or band can soil the sleeve of your clothing, cause skin irritation, and even interfere with watch performance. Be sure to keep the case and band clean at all times. Rust tends to form easily after the watch is exposed to seawater and then left without cleaning. • Sometimes a smudge like pattern may appear on the surface of a resin band. This will not have any affect on your skin or clothing. Wipe the band with a cloth to clean it. • Keep a leather band clean by wiping it with a dry cloth. Both resin bands and leather band can become worn and cracked over time when subjected to normal daily use. • Should your band become badly cracked or worn, be sure to have it replaced with a new one. Request band replacement from your original retailer or an authorized CASIO Service Center. Note that you will be charged for band replacement costs, even if your watch is still covered by its warranty. E-64 • Remember that you wear your watch next to your skin, just like a piece of clothing. Because of this, you should always keep your watch clean. Use a soft, absorbent cloth to wipe off any dirt, sweat, water, or other foreign matter from the case and band. Dangers of Poor Watch Care Rust • Though the stainless steel used for the watch is highly rust-resistant, rust can form if the watch is not cleaned after it becomes dirty. Failure of oxygen to come into contact with the metal because it is dirty causes breakdown of the oxidization layer on the metal surface, which leads to the formation of rust. • Even if the surface of the metal appears clean, sweat and rust in crevasses can soil the sleeves of clothing, cause skin irritation, and even interfere with watch performance. Premature Wear • Leaving sweat or water on a resin band or storing it an area subject to high moisture can lead to premature wear, cuts, and breaks. E-65 Skin Irritation • Individuals with sensitive skin or in poor physical condition may experience skin irritation when wearing a watch. Such individuals should keep their leather band or resin band particularly clean, or switch to a metal band. Should you ever experience a rash or other skin irritation, immediately remove the watch and contact a skin care professional. Battery Replacement • Leave battery replacement up to your original retailer or authorized CASIO Service Center. • Have the batteries replaced only with the type specified by in this manual. Use of other types of batteries can cause malfunction. • When replacing the batteries, also request a check for proper water resistance. Note that you will be charged separately for water resistance inspection. Initial Batteries • The batteries that come loaded in your watch when you purchase it are used for function and performance testing at the factory. E-66 • These types of test batteries may go dead quicker than the normally rated battery life as noted in the User’s Guide. Note that you will be charged for replacement of these batteries, even if replacement is required within the watch’s warranty period. Low Battery Power • Low battery power is indicated by large timekeeping error, when display contents are dim, or when the display does blank. • Operation while battery power is low can result in malfunction. Replace the batteries as soon as possible. E-67 City Code Table Site Data List L-1 City Code Table City Code City PPG HNL ANC YVR SFO LAX DEN MEX CHI MIA NYC CCS* YYT RIO RAI LIS LON Pago Pago Honolulu Anchorage Vancouver San Francisco Los Angeles Denver Mexico City Chicago Miami New York Caracas St. Johns Rio De Janeiro Praia Lisbon London L-2 UTC Offset/ GMT Differential City Code City –11 –10 –9 BCN PAR MIL ROM BER ATH JNB IST CAI JRS MOW JED THR DXB KBL KHI MLE Barcelona Paris Milan Rome Berlin Athens Johannesburg Istanbul Cairo Jerusalem Moscow Jeddah Tehran Dubai Kabul Karachi Male –8 –7 –6 –5 –4 –3.5 –3 –1 0 UTC Offset/ GMT Differential +1 +2 +3 +3.5 +4 +4.5 +5 City Code City DEL DAC RGN BKK JKT* SIN* HKG BJS SEL TYO ADL GUM SYD NOU WLG TBU Delhi Dhaka Yangon Bangkok Jakarta Singapore Hong Kong Beijing Seoul Tokyo Adelaide Guam Sydney Noumea Wellington Nuku’Alofa UTC Offset/ • Based on data as of March 2008. GMT Differential • The rules governing global times (GMT +5.5 +6 +6.5 +7 +8 differential and UTC offset) and summer time are determined by each individual country. * In December 2007, Venezuela changed its offset from –4 to –4.5. Note however, that this watch displays an offset of –4 (the old offset) for the CCS (Caracas, Venezuela) city code. +9 +9.5 +10 +11 +12 +13 L-3 Site Data List Site Anchorage Bahamas Baja, California Bangkok Boston Buenos Aires Casablanca Christmas Island Dakar Gold Coast Great Barrier Reef, Cairns Guam Hamburg Hong Kong L-4 UTC Offset/GMT Differential Standard DST/ Time Summer Time –9.0 –8.0 –5.0 –4.0 –7.0 –6.0 +7.0 +8.0 –5.0 –4.0 –3.0 –2.0 +0.0 +1.0 +14.0 +15.0 +0.0 +1.0 +10.0 +11.0 +10.0 +11.0 +10.0 +11.0 +1.0 +2.0 +8.0 +9.0 Longitude 149°W 77°W 110°W 101°E 71°W 58°W 8°W 158°W 17°W 154°E 146°E 145°E 10°E 114°E Site Honolulu Jakarta Jeddah Karachi Kona, Hawaii Lima Lisbon London Los Angeles Maldives Manila Mauritius Melbourne Miami Noumea UTC Offset/GMT Differential Standard DST/ Time Summer Time –10.0 –9.0 +7.0 +8.0 +3.0 +4.0 +5.0 +6.0 –10.0 –9.0 –5.0 –4.0 +0.0 +1.0 +0.0 +1.0 –8.0 –7.0 +5.0 +6.0 +8.0 +9.0 +4.0 +5.0 +10.0 +11.0 –5.0 –4.0 +11.0 +12.0 Longitude 158°W 107°E 39°E 67°E 156°W 77°W 9°W 0°E 118°W 74°E 121°E 57°E 145°E 80°W 166°E L-5 Site Pago Pago Palau Panama City Papeete Rio De Janeiro Seattle Shanghai Singapore Sydney Tokyo Vancouver Wellington UTC Offset/GMT Differential Standard DST/ Time Summer Time –11.0 –10.0 +9.0 +10.0 –5.0 –4.0 –10.0 –9.0 –3.0 –2.0 –8.0 –7.0 +8.0 +9.0 +8.0 +9.0 +10.0 +11.0 +9.0 +10.0 –8.0 –7.0 +12.0 +13.0 Longitude 171°W 135°E 80°W 150°W 43°W 122°W 121°E 104°E 151°E 140°E 123°W 175°E •Based on data as of 2008. L-6 MO0809-EA