Transcript
639840
Revision E,
JUNE 2016
Mounting Kits For Wide Panel Antennas
BSAMNT-1, BSAMNT-3, BSAMNT-M & BSAMNT-MH: Mounting systems for cylindrical pipe installations (60-115 mm pipe diameter) for heavy duty applications This document explains how to install an antenna using a BSAMNT mount kit. Antennas with two mount points will use BSAMNT-1 or BSAMNT-3. Antennas with three mount points will also use BSAMNT-M or BSAMNT-MH.
ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
DESCRIPTION PIPECLAMP BRACKET, NO FLANGE BRACKET, PIPE CLAMP INTERFACE NOTCHED BRACKET BRACKET SCR,HH,HEX,M8X25,SST,PASS WSHR,LK,SPLT,M8,STL,GALV TWO HOLE PLATE, 8mm X 1.25 PITCH NUT,HEX,M10,STL,GALV WSHR,LK,SPLT,M10,STL,GALV SCR,HCS,HEX,M10X40,STL,GALV NUT,HEX,M12,STL,GALV WSHR,FLT,M12,13X24X2.5,STL,GALV WSHR,LK,SPLT,M12,STL,GALV BOLT,CARRIAGE,M12 X 200,STL,GALV
BSAMNT-1/-3 QUANTITY 4 2 1 1 4 4 2 12 6 6 12 4 4 4
BSAMNT-M/-MH QUANTITY 2 1 1 1 4 4 2 8 4 4 6 2 2 2
Part Lists
two hole plate 7
3 5
6
M8 screw
4
• Bracket edges parallel to each other. (fully collapsed position)
Pre-assembly of Downtilt Brackets by Kit Vendor
www.commscope.com © 2016 CommScope, Inc. All rights reserved. Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information. All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639840 E (06/16)
Page 1 of 4
639840 MAXIMUM TORQUE M12 58N.m (43ft.lbs)
1 14
11 2
Pre-assembly of Pipe Bracket by Field Installer (BSAMNT-1/-3 QTY 2 EA) (BSAMNT-M/-MH QTY 1 EA)
MAXIMUM TORQUE M8 15N.m (11ft.lbs) M10 37N.m (27ft.lbs) M12 58N.m (43ft.lbs)
M10 screw 8
9
10
12 13 11
1
8
9
10
M10 screw
CRITICAL: For initial installation to pipe, downtilt brackets must be configured in pre-assembly position (fully collapsed).
Top / Middle Mount Installations
www.commscope.com © 2016 CommScope, Inc. All rights reserved. Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information. All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639840 E (06/16)
Page 2 of 4
639840 MAXIMUM TORQUE M10 37N.m (27ft.lbs) M12 58N.m (43ft.lbs)
M10 screw 10
9
8
12 13 11
1
Bottom Mount Installation
• Loosen pivot screws . (do not remove)
A
M10 pivot screw (loosen only)
M10 pivot screw (loosen only)
• Remove adjuster screws. • Adjust antenna angle. (use inclinometer)
M8 adjuster screw perimeter location (remove to adjust tilt)
• Reinstall adjuster screws.
M10 pivot screw (loosen only)
• Retighten all screws.
use inclinometer to adjust antenna angle
M8 pivot screw center location (loosen only)
DETAIL A M10 pivot screw (loosen only)
MAXIMUM TORQUE M8 15N.m (11ft.lbs) M10 37N.m (27ft.lbs) M12 58N.m (43ft.lbs)
Adjusting Antenna Tilt - 2 POINT MOUNT
www.commscope.com © 2016 CommScope, Inc. All rights reserved. Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information. All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639840 E (06/16)
Page 3 of 4
639840
M10 pivot screw (loosen only)
• Loosen pivot screws . (do not remove) • Remove adjuster screws. • Adjust antenna angle. (use inclinometer)
M8 pivot screw center location (loosen only)
M10 pivot screw (loosen only)
• Reinstall adjuster screws. Middle Bracket First
M10 pivot screw (loosen only)
• Retighten all screws.
A use inclinometer to adjust antenna angle
M8 adjuster screw perimeter location (remove to adjust tilt)
DETAIL A M10 pivot screw (loosen only)
MAXIMUM TORQUE M8 M10 M12
15N.m (11ft.lbs) 37N.m (27ft.lbs) 58N.m (43ft.lbs)
Adjusting Antenna Tilt - 3 POINT MOUNT
SAFETY NOTICE The installation, maintenance, or removal of an antenna requires qualified, experienced personnel. CommScope installation instructions are written for such installation personnel. Antenna systems should be inspected once a year by qualified personnel to verify proper installation, maintenance, and condition of equipment. CommScope disclaims any liability or responsibility for the results of improper or unsafe installation practices. It is recommended that transmit power be turned off when the field installation is performed. Follow all applicable safety precautions as shown on this page.
Do not install near power lines. Power lines, telephone lines, and guy wires look the same. Assume any wire or line can electrocute you.
Do not install on a wet or windy day or when lightning or thunder is in the area. Do not use metal ladder.
www.commscope.com © 2016 CommScope, Inc. All rights reserved. Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information. All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639840 E (06/16)
Wear shoes with rubber soles and heels. Wear protective clothing including a long-sleeved shirt and rubber gloves.
Page 4 of 4
