Transcript
ＯＰＥＲＡＴＩＯＮＡＬ ＭＡＮＵＡＬ ＭＰＴ－１１１Ｓ／Ｆ
NADA
ELECTRONICS,
LTD. Ｇ２Ｓ－１２０６１１
□
PART NAMES AND FUNCTIONS
PAPER FEED KNOB
POWER SWITCH
REAR PANEL SELECT SWITCH
AC POWER CORD
FEED SWITCH 印刷可
紙送り
OPERATION PANEL
CONNECTOR EARTH TERMINAL
1) SELECT SWITCH（印刷可） Change select(ON-LINE) and deselect(OFF-LINE) by pressing this button switch. LED is lighting in ON-LINE mode. It will stop printing to press this switch. Press again, it will start printing. Remove an error display of the operation panel while printer is an error condition. (Remark)It is not to remove the reason for the errors, but to get the power-on state. 2) FEED SWITCH（紙送り） This switch is valid when in offline mode. Feed paper slowly at first, then it turns rapidly. ★Test print is by pressing this button and on power at the same time. (REF. SELF TEST MODE ) After test printing, this printer is acceptable. (ANK character: 5×7dot) 3) POWER SWITCH ON/OFF power by this switch. 4) PAPER FEED KNOB（A friction type does not have the paper feed knob.） When the paper feed, turn this knob in the direction of the arrow. Please turn the paper feed knob in the power-off state or deselect(OFF-LINE) state. 5) AC POWER CORD（100V, 200V; 50/60Hz） Able to supply power. 6) EARTH TERMINAL Grounded earth terminal. 7) CONNECTOR IF connector: RS232C serial or CENTRONICS parallel selectable when order. 1
□
HOW TO OPEN THE COVER Hold the front side and up as arrow direction shown the figure-1 and -2.
② ①
2
□
HOW TO CLOSE THE COVER Set cover end to the bar as shown in figure.
3
□
HOW TO REPLACE RIBBON CASSETTE ①
Turn a ribbon feed knob manually to stretch ribbon.
②
The ribbon cassette is attached to a print head. Please insert the Locke part of a ribbon cassette in a predetermined position. PRINT HEAD
Try not to get a ribbon hung up on a pointed end of the frame.
RIBBON FEED KNOB
LOCKE PART ③
□
Turn a ribbon feed knob manually to stretch ribbon.
RIBBON CASSET SPECIFICATION 1) 2) 3) 4)
Part Number Material of the ribbon Dimensions of the ribbon Life
：ERC-39B（Color is Black only.） ：NYLON # 40 denier ：13mm（Width） ：1.6 million characters
4
□
HOW TO SET PAPER HOLDER Insert guide of a paper holder as figure.
PAPER HOLDER
The direction of the arrow in Figure.
GUIDE ATTACHMENT GUIDE
5
□
HOW TO SET SPROCKET PAPER ①
Cut straight in the perforations of the paper.
②
Insert the paper to the paper guide.
PAPER FEED KNOB INSERTION OPENING
PINS OF THE SPROCKET PAPER
③
To feed paper by winding the paper feed knob manually or FEED switch, checking the correct adjust of pins and holes. Please turn the paper feed knob in the power-off state or deselect(OFF-LINE) state.
④
□
HOW TO SET FRICTION PAPER ① ② ③
□
Top of form.
Cut straight in the paper. Insert the paper to the paper guide. The paper is discharged to the paper exit to press the FEED switch.
HOW TO TAKE-OFF PAPER Cutting off the paper at the paper guide, then FEED the paper out. Warning! Take off paper by FEED switch motor, Manual taking off will cause paper jamming.
6
□
STYLE OF PAPER １．Folding Paper Size
Our Product number
Specification
Paper Quality
NF-890S
SPROCKET
High-quality Paper
89mm×6inch×35m
NF-760S
SPROCKET
High-quality Paper
76mm×5inch×35m
NF-760
FRICTION
Plain Paper
76mm×5inch×35m
(width×page length×length)
２．Roll Paper Our Product number NR-760
Specification FRICTION
Paper Quality Plain Paper
Size (width×outer diameter×length)
76mm×φ60mm×35m
(Remark) For more information on each paper, please refer to the technical manual.
7
□
OPERATING SUGGESTIONS １．Mechanism is mainly composed of galvanized steel sheet, which sometimes causes rust on the edge face. ２．Printer is not used for a long term, that you do not set the recording paper. Otherwise, the recording paper may be discolored and dirty. ３．Please consult with us for use the product on a vibrating location. If imperceptible vibration is applied to the product a long time, It can cause unexpected problems.
□
PROHIBITED MATTER １．Do not print without paper and ribbon cassette. ２．Do not pull the recording paper in the reverse of the paper feed direction. ３．NEVER USE IN dew condensation! Power ON after non-condensing confirmed. ４．Check paper and platen if some articles are or not. ５．That prohibits turning the paper feed knob in an online state.
□
ABOUT IN-WARRANTY AND MAINTENANCE TERM １．We guarantee this printer for a period of 6 months from the date of shipment. ２．A product out of warranty and in-warranty troubles by user's responsibility does not cover. user's responsibility: use of fall outside the guidelines, damage due to falling, damage by a natural disaster, etc. ３．Even if in-warranty trouble, the printer does not cover it for the printer has been used over the life time. ４．The maintenance term of the printer is five year after out of production. ５．Some of components, as printing unit, etc., shall be exchanged whole unit to maintain. ６．In no event shall NADA be liable for claims based upon breached express or implied consequential or special or for any expenses incurred by reason of the use or misuse, sale or fabrications of products which do not conform to the terms and conditions of this contract.
8
NADA ELECTRONICS, LTD. 1-4-43 MOTOYAMA MINAMIMACHI, HIGASHINADA-KU, KOBE-CITY 658-0015, JAPAN. ＴＥＬ（078）413-1111 ＦＡＸ（078）412-2222 TOKYO
OFFICE
ＴＥＬ（03）3455-4230 ＦＡＸ（03）3455-4249
NAGOYA OFFICE
ＴＥＬ（052）776-1921 ＦＡＸ（052）775-6080
FUKUOKA OFFICE
ＴＥＬ（092）471-8305 ＦＡＸ（092）471-8355
