Transcript
SQUARE D Multi-Link Structured Wiring System Class 1400
Schneider Electric Brands
Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Wiring Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Recommended Pre-wire Schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Installing and Terminating the Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Recommended Product Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Enclosures and Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 General Information and Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Television/Telephone Combination Hubs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 General Information and Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Voice and Data Network Hubs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Expanding the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Audio Distribution Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Video Distribution Hubs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 General Information and Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Satellite Multi-Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 General Information and Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Modulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 General Information and Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Video Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 General Information and Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 3 04/03
© 2001–2003 Schneider Electric All Rights Reserved
Table of Contents Video Wall Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 General Information and Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
IR Target and Emitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 General Information and Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 General Troubleshooting Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Radio Frequency Troubleshooting Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Modulator Troubleshooting for Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Structured Wiring Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Model Number Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
4 © 2001–2003 Schneider Electric All Rights Reserved
04/03
Introduction Product Description PRODUCT DESCRIPTION
INTRODUCTION
The Square D Multi-Link Structured Wiring System represents the next generation of products for home networks. The Square D Multi-Link Structured Wiring System offers a complete range of products that integrate voice, data, and video applications for a complete system solution. Square D warrants the product to be free from defects in materials and workmanship for eighteen months from the date of invoice from Square D or its authorized sales channel. The devices are UL® Listed for use in US markets and CUL® Listed for use in Canada.
APPLICATION DATA The structured wiring modules are wired using Category 5 (CAT-5) or Category 5E (CAT-5E) cable and RG-6 coaxial cables. All structured wiring modules are easily installed into enclosures, also supplied by Square D. Category 5 and 5E Cable Category 5 and 5E cables are made up of four unshielded twisted pairs. Each pair is color coded for application identification. CAT-5 or CAT-5E cables are recommended for telecommunications, camera, and data applications. CAT-5 and CAT-5E cables will support standard analog telephone, digital telephone, and data. Category 5 and Category 5E cables meet TIA/EIA–586A and 570 standards for data applications such as high-speed Internet access. The cables have a bandwidth of 100 MHz and data transmission speeds up to 100 Mbps. CAT-5 and CAT-5E cable installations provide connections for immediate and future computer, video, and telephone upgrades, thus protecting the long-term resale value of the home. NOTE: Category 5/5E cables should not be routed parallel to the AC power wiring unless 14 in. (356 mm) of separation or greater is provided. Cross Category 5/5E cables over AC power wires at 90°. Aluminum Foil Shielding
Foam Polyethylene Dielectric Core
RG-6 Coaxial Cable F-Connector
Copper Clad Center Conductor PVC Jacket
60% Aluminum Braid
RG-6 Quad
RG-6 coaxial cable has an 18 gauge copper coated steel center conductor, polyethylene dielectric core, aluminum braid, and PVC jacket. Standard “F” connectors are used for video, audio, and television equipment connections. Under extreme noise conditions, such as near a radio or television transmitter, use quad-shielded RG-6 cable. NOTES: RG-6 coaxial cable should not be routed parallel to AC power wiring unless 14 in. (356 mm) of separation or greater is provided. Cross RG-6 coaxial cable over AC power wires at 90°. When bending coaxial cable, a radius of no less than four times the outside diameter of the cable should be maintained. For RG-6 coaxial cable, the bending radius should be 1 - 1 1/2 inches or greater.
04/03
© 2001–2003 Schneider Electric All Rights Reserved
5
Section 1–Introduction
www.squared.com/multilink
Section 1–Introduction
Introduction
www.squared.com/multilink
Application Data Installing Modules into Enclosure All structured wiring modules are easily installed into enclosures, also supplied by Square D. Using the hook on the back of the module, hang the module on the enclosure grid, swing the module into place, and push the button on the right side of the module to lock the module into the enclosure grid.
Hook Enclosure grid
Push button to lock module into place
6
Telephone Service Hub Square D model SDM412PJ Telephones RJ-31X R 4 T R 3 T R 2 T R 1 T Expansion
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Wiring Guide Recommended Pre-wire Schemes
WIRING GUIDE
Structured wiring cables run from the wall boxes in the various rooms of the house directly to the structured wiring enclosure (called home run wiring). Two types of wire are used for communication and entertainment: CAT-5 or CAT-5E, made up of 4-UTP (unshielded twisted pairs), and RG-6 coaxial. CAT-5 or CAT-5E 4-UTP wires handle voice and data for up to four telephone lines. CAT-5 or CAT-5E wires can have two to four unshielded twisted pairs. Square D recommends four pairs. RG-6 coaxial wires handle television (antenna or cable), satellite dish, cable modem, or AV modulator signals. Refer to the following table for the recommended wiring schemes. These wires run from the enclosure to the locations indicated in the table. Recommended Pre-wire Schemes Typical Room
Media Center Wire Type
Good
Phone/TV
CAT–5
1
RG–6
1
Wire Type Better
Best
Phone/TV/ Ethernet
Phone/TV/ Ethernet/ Satellite Receiver
Quantity
Quantity
CAT–5
2
RG–6
1
Wire Type
Quantity
CAT–5
2
RG–6
2
Phone/Satellite Receiver/AV Modulators
Phone/TV/Ethernet/ Satellite Receiver/AC Modulators Phone/TV/Ethernet/ Satellite Receiver/AC Modulators/Hi–speed Data
Home Office Wire Type
Quantity
CAT–5
1
RG–6
3
Wire Type
Quantity
CAT–5
2
RG–6
3
Wire Type
Quantity
CAT–5
3
RG–6
3
Wire Type Phone/TV/Cable Modem
Quantity
CAT–5
1
RG–6 Phone/TV/ Ethernet/Cable Modem Phone/TV/ Ethernet/Satellite Receiver/Cable Modem/Hi–speed Data
Wire Type
2 Quantity
CAT–5
2
RG–6 Wire Type
2 Quantity
CAT–5
3
RG–6
3
Telephone and Video Camera Pre-wire Scheme Recommended Color Coding for Category 5/5E Wire Category 5/5E Wire Color
Usage
Gray
Telephone
Red
Security
Blue
Data
Yellow
Demarc and Gateway
For pre-wiring telephone modules, use one gray CAT-5/5E cable from each telephone and modem location, web television and/or satellite box location, and telephone demarcation point (the interface from the telephone service provider). For pre-wiring video camera modules, use one red CAT-5/5E cable from each video camera location (for example, front door) and security panel location. Audio/Video and Television Pre-wire Scheme Recommended Color Coding for Coaxial Wire RG-6 Coaxial Wire Color
Usage
White
Use as send, upstream, or internal cable from modulators to distribution panel
Black
Use as receive, downstream, or external cable from distribution panel to televisions
For pre-wiring audio/video and television modules, use RG-6 coaxial cable. Use black coaxial cable for each television and computer location. Use white coaxial cable for each location where one or more video sources are located, the CATV demarcation point (the interface from the television service provider), and off-air antennas. For satellite dish locations, use two white coaxial cables to the distribution panel. For each satellite receiver location, use one white coaxial cable to the distribution panel. If HDTV satellite dishes are installed, four coaxial cables may be required because the satellite systems can accommodate up to four different receivers from a single dish.
04/03
© 2001–2003 Schneider Electric All Rights Reserved
7
Section 2–Wiring Guide
RECOMMENDED PRE-WIRE SCHEMES
Wiring Guide
www.squared.com/multilink
Installing and Terminating the Cable Section 2–Wiring Guide
Data Pre-wire Scheme For pre-wiring data modules, use one blue CAT-5/5E cable from each computer location, room with a separate peripheral (such as a laser printer), and room where access to the network is needed. Wiring a Telephone Wall Plate To wire a telephone wall plate, refer to the following table. NOTE: The wiring method shown in the table below requires the use of two-line telephones.
Telephone Wall Plate Wiring Using Two Six-Position, Four-Conductor Jacks (RJ-14) Cable Color
Pin Number
Connector Color (As Marked on RJ-14 Modular Connector)
White/Orange
Pin 2
White/Orange
Blue
Pin 3
Blue
White/Blue
Pin 4
White/Blue
Orange
Pin 5
Orange
Jack 1: Pairs 1 and 2
Jack 2: Pairs 3 and 4 White/Brown
Pin 2
White/Orange
Green
Pin 3
Blue
White/Green
Pin 4
White/Blue
Brown
Pin 5
Orange
When a fax machine is present or single-line telephones are used, wire line 1 (blue, blue/white pair) to the center pins (marked blue, blue/white) on the RJ-14 jack. For access to a second line for a fax machine or to enable single-line telephone use, wire line 2 (orange, orange/white pair) to the center pins (marked blue, blue/white) on a second RJ-14 jack.
INSTALLING AND TERMINATING THE CABLE 110 Punch-Down Connectors The 110 punch-down connector is an insulation displacement connection system typically included on combination telephone/video hubs, telephone hubs, and data hubs. The CAT-5/5E wires are inserted into the connectors. To push wire into the connector, use only a 110 punch-down tool. When wiring the connector, keep the wire cable sheath close to the connector and do not untwist the wire more than 1/2 in. (13 mm).
110 punch-down tool
CAT-5/5E cable
8
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Wiring Guide Installing and Terminating the Cable
Modular connectors are attached to each end of a CAT-5/5E jumper cable. Modular connectors are used with television, telephone, data, and Ethernet hubs. There are three six-position connector types, depending on the number and usage of lines. Eight-position connectors are used with the telephone expansion hub (model SDM48PX). For residential purposes, it is recommended that the eight-position connectors (RJ-45) are wired to the T568-A wiring standard. Refer to the table below for the modular connector type and the figures below for wiring configurations. Modular Connector Types Line Usage
Connector Type
Six-position Connectors Single-line telephones, answering machines, and modems (six-position, two-conductor)
RJ-11
Dual-line telephones and answering machines (six-position, four-conductor)
RJ-14
Three-line key service unit (six-position, six-conductor)
RJ-25
Eight-position Connectors Telephones, Ethernet (10 Base-T and 100 Base-T), and data lines (eight-position, eight-conductor)
04/03
© 2001–2003 Schneider Electric All Rights Reserved
RJ-45
9
Section 2–Wiring Guide
Modular Connectors
Wiring Guide
www.squared.com/multilink
Installing and Terminating the Cable Section 2–Wiring Guide
Wiring a Modular Connector The illustrations below show the modular connectors positioned with the tabs down, pins up, and the openings facing toward you. Pair 3
Pair 3 Pair 2 Pair 4
Pair 1
Pair 2
Pair 2
Pair 1
Pair 1
RT
T RT R
1 2 3 4 5 6
1 2 3 4 5 6
RJ-11 Connector
RJ-14 Connector
Pair 1
T T R T RR
T R T R T RT R
RJ-25 Connector
RJ-45 Connector (T568-A standard)
1 2 3 4 5 6
1 2345678
Wiring a Modular Jack To wire a modular jack with CAT-5/5E wiring, follow the wire color code for the TIA/EIA-568-A wiring standard as illustrated for the RJ-45 modular connector. Position the first pair of wires to the terminals closest to the end of the jack. Do not untwist the pairs more than 1/2 in. (13 mm) from the termination point. Push the wires into the terminals of the jack using a 110 punch-down tool and trim. After all pairs are connected, snap on strain relief caps.
110 punch-down tool
10
Strain relief caps
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Wiring Guide Recommended Product Configurations Section 2–Wiring Guide
RECOMMENDED PRODUCT CONFIGURATIONS The following product configurations are guides for installing a structured wiring system for the most common applications. Basic Home • Distributes two telephone lines to six locations and one cable input to four locations • Handles multiple telephone lines for voice, fax and Internet access
Catalog Number
Description
SDM18BW
18 In. (457.2 mm) Enclosure
SDM18CW
18 In. (457.2 mm) Cover
SDM26P14V
Combination Telephone/Video Hub
Incoming RG-6 coaxial cable from cable company or local antenna
RG-6 coaxial cables connected to four television wall plates
OUT
IN
OUT
IN
IN
OUT
OUT
IN
OUT
IN
532-230 5MHzto 1000MHz SPLITTER
SDM26P14V
From Telco
COMBINER
R
Telephones
R 2 T R 1 T
Combo Hub (2 lines x 6 phones, 1inpu t x 4 televisions) Square D model SDM26P14V
Incoming telephone service (two lines)
Internal telephone cables connected to six telephone wall plates (CAT–5/5E unshielded twisted pairs). Each cable can have two to four pairs of wire.
CAT-5/5E cable
04/03
© 2001–2003 Schneider Electric All Rights Reserved
11
Wiring Guide
www.squared.com/multilink
Recommended Product Configurations Section 2–Wiring Guide
Basic Home Office • Distributes four telephone lines to six locations and one cable input to four locations • Allows sharing of files and peripherals among two computers • Handles multiple telephone lines for voice, fax, and Internet access
Catalog Number
Description
SDM18BW
18 In. (457.2 mm) Enclosure
SDM18CW
18 In. (457.2 mm) Cover
SDM8D
Eight-Port Data Hub
SDM46P14V
Combination Telephone/Video Hub
Incoming RG-6 coaxial cable from cable company or local antenna
RG-6 coaxial cables connected to four television wall plates
OUT
IN
OUT
IN
IN
OUT
OUT
IN
OUT
IN
532-230 5MHzto 1000MHz
COMBINER
From Telco
SDM46P14V
R
Telephones
4 R T R 3 R T R R 2 T T R R 1 TT
Combo Hub (2 lines x 6 phones, 1 inpu t x 4 televisions) Square D model SDM46P14V
Internal telephone cables connected to six telephone wall plates (CAT-5/5E unshielded twisted pairs). Each cable can have two to four pairs of wire.
Incoming telephone service (four lines) CAT-5/5E cable
Data Hub ( 8 cables, TIA-568A)
Category 5 Compliant Square D model SDM8D
SDM8D
CAT-5/5E cable
Cables connecting to data jacks in eight wall plates
Up to eight data jacks can be wired using this equipment. However, unless an Ethernet hub is used, only two computers can be networked by connecting two RJ-45 jacks with a patch cord on the data hub. NOTE: To allow two computers to be networked, one crossover patch cord must be used somewhere in the system, i.e., between one computer and data outlet.
12
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Wiring Guide
If high-speed Internet service will be brought to the home over the telephone lines (DSL), the incoming telephone line should be connected to the combination hub (model SDM46P14V) and then jumped to the data hub (model SDM8D) as shown in the figure below. In this scenario, one computer can have DSL service. The high-speed Internet line can easily be moved to another computer by changing the location of the jumper on the SDM8D. Incoming RG-6 coaxial cable from cable company or local antenna
RG-6 coaxial cables connected to four television wall plates
OUT
IN
OUT
IN
IN
OUT
IN
OUT
OUT
IN
532-230 5MHzto 1000MHz SPLITTER
From Telco
SDM46P14V
R
COMBINER
Telephones
4 R T R 3 R T R R 2 T T R R 1 T
Combo Hub (2 lines x 6 phones, 1inpu t x 4 televisions)
Square D model SDM46P14V
Internal telephone cables connected to five telephone wall plates (CAT-5/5E unshielded twisted pairs). Each cable can have two to four pairs of wire.
Incoming telephone service (four lines) Sends DSL to office
Data Hub ( 8 cables, TIA-568A)
Category 5 Compliant Square D model SDM8D
DSL Modem
SDM8D
Cables connecting to data jacks in six wall plates To data jack in home office
04/03
© 2001–2003 Schneider Electric All Rights Reserved
13
Section 2–Wiring Guide
Recommended Product Configurations
Wiring Guide
www.squared.com/multilink
Recommended Product Configurations Section 2–Wiring Guide
Advanced Home Office • Distributes four telephone lines to six locations • Creates a LAN by connecting up to five computers or peripherals through the Ethernet hub (model SDM5DE) • Allows a high-speed Internet connection to be shared among computers • Distributes CATV or antenna signals to up to eight televisions Catalog Number
Description
SDM18BW
18 In. (457.2 mm) Enclosure
SDM18CW
18 In. (457.2 mm) Cover
SDM4AC
Four-Outlet AC Accessory (Two Plugs)
SDM46P
Phone Board
SDM8D
Eight-Port Data Hub
SDM5DE
Ethernet Hub
SDM38VBIR or SDM38VHIR
Video Hub
Five rooms have ethernet connections
Data Hub ( 8 cables, TIA-568A)
Category
5 Compliant
Square D model SDM8D
SDM8D
Power supply-included (model SDM350087) CAT-5/5E patch cords (models to SDM4AC SDM1DC or SDM2DC)
CAT-5 cable To data jacks in remote wall plates
Ethernet
Hub 10 BASE-T (5 RJ-45 inputs, 1 uplink) Square D model SDM5DE
1
2
3
4
Col.
5
Pwr
Link/Act.
SDM5DE Up link
5
4
3
2
1
+5VDC
LED glows when power is applied
Antenna or cable (model SDM38VHIR) Cable only (model SDM38VBIR)
IR
Gnd
+12vdc
Power supply-included (model SDM350086) to SDM4AC Adapter (included)
B +Pwr
Modulators
Televisions
SDM38VBIR
A
Up to eight televisions
RG-6 coaxial cable
14
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Wiring Guide
NOTES: If high-speed Internet service is brought to the home over the telephone lines (DSL), the incoming telephone line should be connected to the SDM46P and then jumped to the SDM8D through the DSL modem (as shown in the figure below). If the Internet service provider (ISP) allows multiple IP addresses to be leased to one modem, then the high-speed Internet service may be available to all the computers in the home using the Multi-Link Ethernet Hub. In this situation, the high-speed Internet line will jump from the SDM8D to the “uplink” port in the SDM5DE. All the computers connected to the Ethernet hub must have firewall software or hardware installed since they all will have access to the high-speed line at the same time. If the ISP does not allow multiple IP addresses to be leased to one modem, then replace the Multi-Link Ethernet Hub in the figure below with a router (purchased separately).
Security system connection (RJ-31X only)
Telephone Master Hub (4 lines x 6 phones) Square D model SDM46P
From Telco
Expansion Ports
Telephones
RJ31X
R T R T R 2 T R 1 T 4
SDM46P
3
Out
Four lines from telephone company (CAT-5/5E, four unshielded twisted pairs)
Five rooms have ethernet connections
Data Hub ( 8 cables, TIA-568A)
Category 5 Compliant Square D model SDM8D
SDM8D
DSL Modem Power supply-included (model SDM350087) to SDM4AC
CAT-5 cable To data jacks in remote wall plates Ethernet
1
2
3
4
Hub 10 BASE-T (5 RJ-45 inputs, 1 uplink) Square D model SDM5DE
Col.
5
Pwr
Link/Act.
SDM5DE
Up link
5
4
3
2
1
+5VDC
04/03
© 2001–2003 Schneider Electric All Rights Reserved
15
Section 2–Wiring Guide
Recommended Product Configurations
Wiring Guide
www.squared.com/multilink
Recommended Product Configurations Section 2–Wiring Guide
Advanced Video and Security Camera • Distributes four telephone lines to six locations • Creates a local channel for viewing a camera signal • Distributes camera signal along with the cable television or antenna signals to up to eight televisions • No power is necessary at the camera, it is powered through the channel injector • Multiple cameras can be added to the system (a channel injector is needed for each one) Catalog Number
Description
SDM18BW
18 In. (457.2 mm) Enclosure
SDM18CW
18 In. (457.2 mm) Cover
SDM4AC
Four-Outlet AC Accessory (Two Plugs)
SDM46P
Phone Board
SDM38VBIR
Video Hub
SDM1VC
Black and White Camera
SDM11VMB or SDM11VMH
Channel Injector
Power supply-included (model SDM350079) to model SDM4AC
SDM11VMB or SDM11VMH
Make all cables and CAT-5 connections first. Power the channel injector last. Connect antenna or incoming cable to channel injector (model SDM11VMH) CATV/Ant input or the CATV to model SDM11VMB. RG-6 coaxial cable
CAT-5/5E cable
Video camera-rear view (model SDM1VC)
SDM1VC
Power supply-included (model SDM350086) to SDM4AC
SDM38VBIR
LED glows when power is applied
IR
Gnd
+12vdc
Adapter (included)
B +Pwr
Modulators
Televisions
A
Up to eight televisions
RG-6 coaxial cable
16
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Wiring Guide Recommended Product Configurations
• • • • • • • •
• • •
Distributes four telephone lines to six locations Creates a local channel for viewing a camera signal Distributes camera signal along with the cable television or antenna signals to up to eight televisions No power is necessary at the camera, it is powered through the channel injector Multiple cameras can be added to the system (channel injectors can be cascaded) Video sources, such as DVD players, are connected via line level inputs to the set top modulator (model SDM41VTST) Set top modulator modulates all the inputs and combines them onto a single coaxial cable for distribution back to the video hub Output of the set top modulator is connected to port B of the video hub, which allows the video hub to be powered via the set top modulator NOTE: Port A on the video hub is also used to connect modulated signals, however, no IR control can be passed through this port Cable or antenna signal is connected to the model SDM11VMB IR targets are connected in-line with each television where IR control is desired IR emitters are connected to the set top modulator and position over the IR sensor on the video source device
Catalog Number
Description
SDM18BW
18 In. (457.2 mm) Enclosure
SDM18CW
18 In. (457.2 mm) Cover
SDM4AC
Four-Outlet AC Accessory (Two Plugs)
SDM46P
Phone Board
SDM38VBIR or SDM38VHIR
Video Hub
SDM41VTST
4-Input Set Top Modulator
SDM2VCC
Color Camera
SDM11VMB or SDM11VMH
Channel Injector
SDM1VIR
IR Target
SDM2VIR
IR Emitter
For satellite applications, see pages 41–43.
04/03
© 2001–2003 Schneider Electric All Rights Reserved
17
Section 2–Wiring Guide
Media Center and Security Camera
Wiring Guide
www.squared.com/multilink
Section 2–Wiring Guide
Recommended Product Configurations Note: The satellite dish and receiver, CCTV Camera, VCR, and DVD shown are not Square D Multi-Link products.
Satellite dish and receiver Video/audio outputs
CCTV Camera at front door Terminating jumpers (on side of unit) A BC D
Power connection
OUTPUT
RCA "Y" adapter to local monitor or Dolby Pro-Logic system
A BC D
CH B
CH D
SDM41VT
Remove jumper for Hi-Z (See manual)
CH A
CH C
POWER 15VDC 900mA
VIDEO
AUDIOL
AUDIOR
VIDEO
AUDIOL
AUDIOR
Optional IR emitter (model SDM2VIR) repeats what the IR target “sees” in the other room. Attach the IR emitter directly over the IR sensor.
Video/audio outputs Use only shielded 75 ohm coaxial cable VCR
12:00 VCR
DVD RG-6 coaxial preferred
Power option-Do not power. Power is obtained through port B of set top modulator. To more televisions Optional IR target (model SDM1VIR) may be used at any or all televison locations.
SDM38VHIR or SDM38VBIR
Control the DVD, DSS, or VCR from any room. RG-6 coaxial cable
Power supply-included (model SDM350079) to model SDM4AC
SDM11VMB or SDM11VMH
CAT-5/5E cable
Make all cables and CAT-5 connections first. Power the channel injector last. Connect antenna or incoming cable to channel injector (model SDM11VMH) CATV/Ant input or the CATV to model SDM11VMB. Security system connection (RJ-31X only) Video camera-rear view Telephone Master Hub (4 lines x 6 phones) Square D model SDM46P
From Telco
R T R T R 2 T R 1 T 4
Expansion Ports
Telephones
RJ31X
3
SDM1VC
Out
Four lines from telephone company (CAT-5/5E, four unshielded twisted pairs) SDM46P
18
© 2001–2003 Schneider Electric All Rights Reserved
Internal telephone cable connected to six telephone wall plates (CAT-5/5E unshielded twisted pairs). Each cable can have two to four pairs of wire.
04/03
www.squared.com/multilink
Enclosures and Brackets Product Description
ENCLOSURES AND BRACKETS
The enclosures are the housing components of the Square D Multi-Link Structured Wiring System. Each enclosure has a mounting grid, allowing any structured wiring module to easily mount into the enclosure. Modules can be mounted on either side of the grid and upside down. The universal mounting bracket (model SDM10BW) can be surface mounted over a single- or double-gang box or mud ring. Any Square D Multi-Link Structured Wiring module can be installed onto the mounting bracket. To give the bracket a finished look, a snap-on cover (model SDM10CW) is available. Universal Mounting Bracket (Model SDM10BW) Features: • 10 in. (254 mm) high, 6.5 in. (165 mm) wide, .35 in. (9 mm) deep • 10 in. (254 mm) of grid mounting space • Vertical or horizontal mounting • Surface mount over single- or double-gang openings • Optional cover (model SDM10CW) • Painted steel, white
SDM10BW
SDM10BW With Modules Installed
Cover (Model SDM10CW) Features: • 11 in. (279 mm) high, 6.7 in. (170 mm) wide, 4.5 in. (114 mm) deep • Snap-on cover design • Painted steel, white
04/03
© 2001–2003 Schneider Electric All Rights Reserved
19
Section 3–Enclosures and Brackets
PRODUCT DESCRIPTION
Enclosures and Brackets
www.squared.com/multilink
Product Description Enclosures (Models SDM18BW and SDM36BW)
Section 3–Enclosures and Brackets
Features: • Model SDM18BW is 18 in. (457.2 mm) high, 14.25 in. (362 mm) wide, and 3.5 in. (89 mm) deep, with 34 in. (864 mm) of grid mounting space • Model SDM18BW has two columns of grid mounting space, each column is 17 in. (432 mm) • Model SDM36BW is 36 in. (914.4 mm) high, 14.25 in. (362 mm) wide, and 3.5 in. (89 mm) deep, with 70 in. (1778 mm) of grid mounting space • Model SDM36BW has two columns of grid mounting space, each column is 35 in. (889 mm) • Side mounting tabs included for field installation • Fits between studs on 16 in. (406 mm) center lines • Surface or flush mounting • Optional combination flush/surface cover: cover dimensions for SDM18CW –19.5 in. (495.3 mm) high, 15.75 in. (400 mm) wide and SDM36CW–37.5 in. high (953 mm), 15.75 (400 mm) wide SDM18BW With Modules Installed
• Can be mounted upside down • Accepts model SDM4AC or model SDM8AC power accessory • Four 2 in. (51 mm) and two 1/2 in. (13 mm) knockouts in each endwall • Painted steel, white • Paint shield included
SDM18CW and SDM18BW
20
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Enclosures and Brackets Product Description
The AC power accessories (models SDM8AC and SDM4AC) mount inside the enclosures to provide a UL® listed location for power supplies. All of the enclosures accept the AC power accessories.
Features: • SDM8AC will mount four receptacles, providing eight outlets for four power supplies • SDM4AC will mount two receptacles, providing four outlets for two power supplies • Uses standard duplex receptacles, not included SDM8AC
• Mounts in any of the four corners of model SDM18BW or model SDM36BW enclosure • Mounting hardware included • UL Listed • SDM8AC covers 5.5 in. (140 mm) of grid mounting space on each side, 11 in. (280 mm) total • SDM4AC covers 5.5 in. (140 mm) of grid mounting space on one side
SDM4AC
SDM18BW with SDM4AC and Other Modules Installed
04/03
© 2001–2003 Schneider Electric All Rights Reserved
21
Section 3–Enclosures and Brackets
AC Power Accessories (Models SDM8AC and SDM4AC)
Enclosures and Brackets
www.squared.com/multilink
General Information and Application Data GENERAL INFORMATION AND APPLICATION DATA Section 3–Enclosures and Brackets
Mounting the Enclosure The enclosures can be flush mounted between studs. For versatile flush mounting, the mounting tabs are field installed. Three available positions for the flush mounting tabs allow for wall thicknesses of 1/2 in. (13 mm), 5/8 in. (16 mm) or 3/4 in. (19 mm). Nail holes are provided in each sidewall for flush mounting in existing installations. Mounting holes are also provided in the rear of the enclosure for surface mounting. Covers SDM18CW and SDM36CW are combination covers for flush or surface applications. NOTE: The enclosure should not be mounted next to an AC power distribution panel. Maintain 17.5 in. (445 mm) or more between the structured wiring panel and the home’s AC panel.
16.0
0 in (406 . on cen ter mm)
Mounting tab hole and hole inside enclosure
Knockout
Enclosure
Mounting the AC Power Accessory The AC power accessory is easily mounted into the enclosure using the hardware provided. The AC power accessory can be mounted into any corner of the enclosure. Low voltage wires exit the AC power accessory through the grommets provided. The grommets can be cut to accommodate the wiring.
Left or right
Location of knockouts for 120 VAC
OEM AC ADAPTOR Part no.: 123-456 U
Top or bottom
L
Enclosure Grommet cut for wiring
AC Power Accessory Mounting Locations (SDM8AC depicted)
22
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Enclosures and Brackets General Information and Application Data
The AC power accessories include a grounding lug. The enclosures do not include a separate grounding lug. However, there is a #10–32 threaded hole provided in the top and bottom endwall for the user to install ground lugs, as necessary. Installing the Cables Install the data and video cables into the enclosure through removable knockouts. Line the knockout holes with grommets (provided) to protect incoming cable. Cabling running through knockout hole Knockout hole with grommet
Grommet
Cabling in enclosure
Paint shield
Installing the Cover Cover installation is streamlined with temporary hardware (provided).
Enclosure mounting holes
Install nails through the mounting holes to temporarily align screw holes.
Cover
04/03
© 2001–2003 Schneider Electric All Rights Reserved
23
Section 3–Enclosures and Brackets
Grounding Lug
Enclosures and Brackets
www.squared.com/multilink
Section 3–Enclosures and Brackets
General Information and Application Data
24
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Television/Telephone Combination Hubs Product Description
PRODUCT DESCRIPTION The combination hubs provide a four-way passive splitter to distribute incoming video (CATV or antenna) signals to four locations. The hubs incorporate 110 punch-down blocks for distributing telephone lines. Combination Hubs (Models SDM26P14V and SDM46P14V) Features: • Distributes CATV or antenna to four locations • Telephone service for two lines (model SDM26P14V) or four lines (SDM46P14V) with outputs to six locations • 3 in. (76.2 mm) of grid mounting space.Video F-connectors extend 1/2 in. (13 mm) above the hub mounting pan. Allow approximately 2 in. (51 mm) clearance for cable bending radius above the module.
SDM46P14V
SDM26P14V
GENERAL INFORMATION AND APPLICATION DATA Combination Hubs See the following figure for the typical installation of combination hubs.
RG-6 coaxial cables connected to four television wall plates RG-6 coaxial cable from cable company or antenna
OUT
IN
OUT
IN
IN
OUT
OUT
IN
OUT
IN
532-230 5MHzto 1000MHz SPLITTER
From Telco
COMBINER
R
Telephones
R T R 1 T 2
Two lines from telephone company (CAT-5/5E unshielded twisted pairs)
Combo Hub (2 lines x 6 phones, 1inpu t x 4 televisions)
Square D model SDM26P14V
SDM26P14V
04/03
© 2001–2003 Schneider Electric All Rights Reserved
Internal telephone cables connected to six telephone wall plates (CAT-5/5E, two unshielded twisted pairs). Each cable can have two to four pairs of wire.
25
Section 4–Television/Telephone Combination Hubs
TELEVISION/ TELEPHONE COMBINATION HUBS
Television/Telephone Combination Hubs
www.squared.com/multilink
General Information and Application Data SPECIFICATIONS Passive Splitter Section 4–Television/Telephone Combination Hubs
The specifications for the passive video splitter portion of the combination hubs are shown in the following table.
Parameter
Insertion Loss In-Out (dB maximum)
Return Loss Input (dB maximum)
Return Loss Output (dB minimum)
Isolation OUT-OUT (dB minimum)
26
Frequency (MHz)
SDM26P14V SDM46P14V
5–40
6.7
40–400
6.9
400–500
7.2
500–600
7.5
600–1000
7.8
5–40
22
40–400
24
400–500
27
500–600
25
600–1000
23
5–40
24
40–400
26
400–500
24
500–600
25
600–1000
23
5–40
24
40–400
28
400–500
25
500–600
24
600–1000
23
Power Pass
500 mA
One port or all ports
Impedance
5–1000
75 ohms
RFI (dB)
5–1000
130 dB
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Voice and Data Network Hubs Product Description PRODUCT DESCRIPTION The voice and data network hubs distribute telephone and data signals to multiple locations throughout the home. Each hub uses the standard grid mounting and will fit in any enclosure model or the universal mounting bracket. Telephone Master Hub (Model SDM46P) Section 5–Voice and Data Network Hubs
Features: • Telephone service for four lines with outputs to six separate locations • Security panel connection RJ-31X only (top jack) for seizure of line 1
SDM46P
• 110 punch-down connectors • Can be mounted upside down • Expansion jack RJ-45 (bottom jack) for telephone expansion hub (model SDM48PX) • 3 in. (76.2 mm) of grid mounting space Telephone Expansion Hub (Model SDM48PX) Features: SDM48PX
• Accessory to telephone master hub (model SDM46P) • Telephone service for four lines with outputs to eight separate locations (when used with SDM46P, 14 outlets are accommodated)
Security system connection (RJ–31X only)
Telephone Master Hub (model SDM46P)
• CAT-5/5E patch cord included to connect to SDM46P • 110 punch-down connectors
Telephone Master Hub (4 lines x 6 phones)
Square D model SDM46P From Telco
Expansion Ports
• Can be mounted upside down
Telephones
• 3 in. (76.2 mm) of grid mounting space
RJ31X
R T R 3 T R 2 T R 1 T 4
• Expansion jack allows multiple SDM48PX units to be cascaded, providing expanded telephone distribution (see graphic on the left)
Out
Four lines from telephone company (CAT–5/5E, four unshielded twisted pairs)
Telephone Interface Hub/Patch Panel (Model SDM412PJ) CAT–5 patch cord Telephone Expansion Hub (model SDM48PX) Telephone Expansion Hub (4 lines x 8 phones)
RJ-45 J10
J8 110D-4 110D -4
J7 110D-4 110D -4
J6 110D-4 110D -4
J5 110D-4 110D -4
J3 110D-4 110D -4
J4 110D-4 110D -4
J2 110D-4 110D -4
J1 110D-4
RJ-45 J9
Out Blu
Blu
Blu
Blu
Blu
Blu
Blu
Blu
• RJ-45 modular jacks • Can be mounted upside down
Telephones
In
• Telephone service for four lines with outputs to twelve separate locations • 110 punch-down connectors for incoming telephone company service
Square D model SDM48PX
Expansion Ports
Features:
R T R T R T R T
4 3
• 3 in. (76.2 mm) of grid mounting space
2 1
• Expansion jack allows connection to additional SDM412PJ for large applications • Use with SDM8D data hub and SDM5DE Ethernet hub to allow easy reassignment of phone outlets to data network outlets
CAT–5 patch cord Telephone Expansion Hub (model SDM48PX) Telephone Expansion Hub (4 lines x 8 phones)
Square D model SDM48PX
Expansion Ports RJ-45 J10
Telephones J8 110D-4 110D -4
J7 110D-4 110D -4
J6 110D-4 110D -4
J5 110D-4 110D -4
J3 110D-4 110D -4
J4 110D-4 110D -4
J2 110D-4 110D -4
J1 110D-4 110D -4
In
RJ-45 J9
Out Blu
Blu
Blu
Blu
Blu
Blu
Blu
Blu
R T R T R T R T
4 3 2 1
SDM412PJ
04/03
© 2001–2003 Schneider Electric All Rights Reserved
27
Voice and Data Network Hubs
www.squared.com/multilink
Product Description Data Termination Hub (Model SDM8D) Features: • Certified 100 Base-T performance • CAT-5/5E performance in a multi-port hub • Terminates eight CAT-5/5E lines with RJ-45 jacks • Terminates eight CAT-5/5E lines with 110 punch-down connectors • Can be mounted upside down SDM8D
• Circuits may be bridged for telephone distribution • 3 in. (76.2 mm) of grid mounting space
Telephone company line
• Suitable for Digital Subscriber Line (DSL) from telephone company • Distributes Ethernet connections • Distributes camera connections
CAT-5/5E data hub (model SDM8D) TIA-568A)
Category 5 Compliant Square D model SDM8D
Data Hub ( 8 cables, TIA-568A)
CAT-5/5E data hub (model SDM8D)
The data termination hub can be used for telephone distribution by connecting two data hubs using CAT-5/5E patch cords. In the figure to the left, one hub shows the telephone lines bridged at the hub to bring telephone distribution to the jacks. The additional hub has the cables connecting to voice or data jacks in eight wall plates.
(
Section 5–Voice and Data Network Hubs
• 110 punch-down connectors are connected to the RJ-45 jacks
Category 5 Compliant H628 Square D model SDM8D
Cables connecting to voice or data jacks in eight wall plates
Bridgeable CAT-5/5E Hub (Model SDM8DB) Features: • Certified 100 Base-T performance • Eight CAT-5/5E circuits (110 to RJ-45) • Eight additional 110 connectors to bridge for telephone distribution (see diagram below) • 4.5 in. (114.3 mm) of grid mounting space
SDM8DB
The bridgeable CAT-5/5E data hub can also be used for telephone distribution. In the following figure, three telephone outlets are wired using CAT-5/5E cables terminated to the lower section of 110 punch-down connectors. The wires can also be terminated into the RJ-45 jacks via RJ-45 plugs. To bring telephone distribution to the jacks, bridge the telephone lines by running the incoming telephone lines across the top set of 110 punch-down connectors. All CAT-5/5E circuits can be bridged for telephone distribution. The remaining terminals are available for use as data terminations. The lines from the telephone company bridged across the connectors.
Data Hub (8 cables, TIA-568A) Category 5 Compliant Square D model SDM8DB
Telephone lines
28
© 2001–2003 Schneider Electric All Rights Reserved
Data lines
04/03
www.squared.com/multilink
Voice and Data Network Hubs Product Description Ethernet Hub (Model SDM5DE)
The Ethernet hub is easier to install when used as a companion piece with the data termination hub. Features: SDM5DE
• Certified 10 Base-T performance • Five-port hub • RJ-45 connectors • Can be mounted upside down • FCC and UL approved • Uplink port provided to jumper to additional SDM5DE units
VOICE AND DATA NETWORK HUBS
• 120 Vac power supply included • 4 in. (102 mm) of grid mounting space
DSL from telephone company
DSL sent to home office computer only Ethernet connection from home office Four ethernet connections Data Hub (8 cables, TIA-568A) Category 5 Compliant
Square D model SDM8DB
Hub ( 8 cables, TIA-568A)
Camera signal connects to channel injector by way of the RJ-45 patch cord
CAT-5/5E data hub (model SDM8DB)
Camera wire (CAT-5/5E)
Cables connecting to two phone jacks (one in home office) Network hub 10 base-t Square D model SDM5DE
Cable connecting to data jacks in five wall plates
Ethernet hub (model SDM5DE)
Power Link/ normal
1
2
3
4
5
10 base-t hub
Antenna or incoming cable
Channel injector (model SDM11VMH)
Power supply (model SDM350079)
Program CAT-5 video
Output
CATV /Ant
Power
Channel Injector
NOTE: The channel injector shown in this scheme is not required for Ethernet connections.
04/03
© 2001–2003 Schneider Electric All Rights Reserved
29
Section 5–Voice and Data Network Hubs
The Ethernet hub is used to provide a five port 10 Base-T hub to interface computers and printers throughout the home. This hub creates a local area network, allowing file and peripheral (printer) sharing among multiple computers. The Ethernet hub has activity LEDs for network status and diagnosis.
Voice and Data Network Hubs
www.squared.com/multilink
Technical Information SPECIFICATIONS Ethernet Hub (Model SDM5DE) Specifications at 77 + 9 °F (25 + 5 °C) Compliance Network Interface
Section 5–Voice and Data Network Hubs
Maximum Cable Length LED Indicators Environmental
Power Supply
IEEE 802.3
10 Base-T
RJ-45 ports
5
RJ-45 uplink
1
CAT-5/5E (UTP)
328 ft (100 m)
each unit
PWR, COL
each port
LINK/ACT
operating temperature
32°F to 122°F (0°C to 50°C)
model number
SDM350087
output current
800 mA maximum
output voltage
5 Vdc ± 5% regulated
input power
105–125 Vac
EXPANDING THE NETWORK To expand the network, one of the ports on the Ethernet hub is used to connect to the uplink port on the expansion hub using a straight through RJ-45 CAT-5 cable. See the graphic below.
Ethernet
Hub 10 BASE-T (5 RJ-45 inputs, 1 uplink) Square D model SDM5DE
1
2
3
4
Col.
5
Pwr
Link/Act.
Ethernet hub (model SDM5DE) Uplink
5
4
3
2
1
+5VDC
Connect to four network devices or to the “uplink” port of additional ethernet hubs.
Ethernet
Hub 10 BASE-T (5 RJ-45 inputs, 1 uplink) Square D model SDM5DE
1
2
3
4
Col.
5
Pwr
Link/Act.
Ethernet hub expansion (model SDM5DE) Uplink
5
4
3
2
1
+5VDC
Leave this port unused
Connect to four network devices or to the “uplink” port of additional ethernet hubs.
Additional hubs can be used, as long as the path between any two network devices does not exceed four hubs and five cables. NOTE: When the uplink port of a hub is used, a network device cannot be connected to port 5. All hubs must be powered.
30
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Audio Distribution Hub Product Description
PRODUCT DESCRIPTION Speaker Distribution Hub (Model SDM16A) Features: • Distributes one stereo audio to six rooms • 3 in. (76.2 mm) of grid mounting space • Connects with standard speaker wire (12 gauge maximum) to supply six pairs of speakers with stereo audio from one receiver or amplifier • Outputs wired (via speaker wire) to impedance matching volume controls (not supplied by Square D) • Speaker wire terminations removable for easy wiring • Speakers not supplied by Square D
SDM16A
04/03
© 2001–2003 Schneider Electric All Rights Reserved
31
Section 6–Audio Distribution Hub
AUDIO DISTRIBUTION HUB
Audio Distribution Hub
www.squared.com/multilink
Section 6–Audio Distribution Hub
General Information and Application Data
32
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Video Distribution Hubs Product Description PRODUCT DESCRIPTION
SDM13VS
The splitter hubs are cable company grade passive splitters that are tilted to 10° for easy connections. Three-, four-, and eight-way balanced splitters are available. The video distribution hubs amplify and distribute antenna and/or cable signals to television locations. The high headroom amplifier and bi-directional amplifier video hubs (models SDM38VHIR and SDM38VBIR) include two modulator inputs to add locally generated channels for cameras, DVDs, or VCRs. All of the video distribution hubs are compatible with NTSC and future HDTV signals. Section 7–Video Distribution Hubs
VIDEO DISTRIBUTION HUBS
Splitter Hubs (Models SDM13VS, SDM14VS, and SDM18VS) Features: • Cable company grade passive splitter • Model SDM13VS is a three-way balanced splitter, 5–1000 MHz • Model SDM14VS is a four-way balanced splitter, 5–1000 MHz SDM14VS
• Model SDM18VS is an eight-way balanced splitter, 5–1000 MHz • Splitter tilted 10° for easy connections • -130 dB RFI rejection • 2 in. (51 mm) of grid mounting space NOTES: The splitter hubs are not DC passing.
SDM18VS
Video Amplifier Hub (Model SDM16VAB) The video amplifier hub (model SDM16VAB) distributes community antenna television (CATV) or antenna signals to six televisions. The hub has four standard outputs (up to 75 ft, 22.9 m) and two long outputs (up to 150 ft, 45.8 m). The SDM16VAB has a broadband amplifier (54–806 MHz) and a 5–42 MHz return path for pay-per-view and interactive cable. The video amplifier hub works like a zero-loss splitter. The signals that are put on the antenna/CATV input will appear on the outputs with about 1dB of gain for short outputs and about 4 dB of gain for long outputs. SDM16VAB
Features: • Distributes CATV or antenna to six televisions • Four standard “short” outputs (up to 75 ft, 22.9 m) • Two long outputs (up to 150 ft, 45.8 m) • Up to four additional hubs (model SDM16VAB) can be cascaded (from the four standard “short” outputs only) of a master hub • HDTV compatible • Bi-directional with a 5–42 MHz return path for interactive applications and pay-per-view boxes • Can be mounted upside down • LED power indicator • 120 Vac power supply included • 3 in. (25.4 mm) of grid mounting space • Termination caps are not required
04/03
© 2001–2003 Schneider Electric All Rights Reserved
33
Video Distribution Hub
www.squared.com/multilink
Product Description Adding a Camera
Section 7–Video Distribution Hubs
A camera channel can be added to the video amplifier hub (model SDM16VAB) using the channel injector (model SDM11VMH or SDM11VMB) and the camera (example: model SDM2VC). The channel injector adds the camera channel to the existing off-air channels and the video amplifier hub distributes the channel to all the outputs. See the figure below.
Camera (model SDM2VC)
Program
Channel injector (model SDM11VMH)
CAT-5 video
CATV /Ant
Output
Video Amplifier
Power
Hub (1 inpu t x 6 t elev is ions)
Square D model
Video amplifier hub (model SDM16VAB)
Power
+15VDC
Short
Long
CATV/ Ant
Televisions
Camera channel is now available on all televisions in the house.
Video Hubs (Models SDM38VHIR and SDM38VBIR) The video hubs work like a zero-loss splitter and signal combiner. The signals that are put on the antenna or cable television input will appear on the outputs with about 3dB of gain. The modulator inputs will automatically appear on the outputs at an FCC legal level. Features:
SDM38VHIR
• SDM38VHIR is a high headroom amplifier video hub used with CATV systems or antennas for off-air digital and analog television signals. The amplifier handles signal differences between high-powered analog VHF (off-air television channels 2 through 13) and low-powered digital UHF (off-air television channels 14 through 69). Use SDM38VBIR if CATV services require a return path. • SDM38VBIR is a bi-directional amplifier video hub used with CATV services using pay-per-view boxes and interactive cable and has a 5–42 return path. The bi-directional system is not for use with off-air antennas. • Bi-directional with a 5–42 MHz return path for pay-per-view boxes (SDM38VBIR only) • Distributes CATV (SDM38VBIR or SDM38VHIR) or antenna (SDM38VHIR only) to eight televisions • Maximum 150 ft (46 m) coaxial cable run from all eight outputs • HDTV compatible
SDM38VBIR
34
• Two modulator inputs to add locally generated channels (camera, VCR, or DVD)
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Video Distribution Hubs Product Description
• Use modulator input B for IR information passing • IR repeating system using 5-volt targets • Antenna isolation compliant with FCC Part 15 requirements (SDM38VHIR only) • 120 Vac power supply and adapter included • LED power indicator • Up to eight additional hubs (models SDM38VBIR or SDM38VHIR) can be cascaded from a master hub • Termination caps are not required Modulator Inputs The high headroom amplifier and bi-directional amplifier video hubs (models SDM38VHIR and SDM38VBIR) have modulator inputs to add locally generated channels. The new channel is selected using the programming instructions included with the modulator or the channel injector (see the “Programming” section for modulators on page 50). Any television connected to the video hub output by coaxial cables can receive the signal when tuned to the proper channel. For typical installation, see the figure below.
Power supply-included (model SDM350086) Adapter (included)
LED glows when power is applied
Antenna or cable (model SDM38VHIR) Cable only (model SDM38VBIR)
IR
Gnd
+12vdc
Video hub (model SDM38VHIR)
B +Pwr
Modulators
Televisions
A
Connect modulators Modulator to A or B inputs
Up to eight televisions
DVD, VCR, or Satellite
RG-6 coaxial cable
To increase the number of modulator inputs, a modulator combiner (model SDM81VC) is connected to a video hub modulator input port to work as an expansion hub. When the modulator combiner is used with a video hub, each of the eight locations can receive the broadband feed as well as the modulated channels.
04/03
© 2001–2003 Schneider Electric All Rights Reserved
35
Section 7–Video Distribution Hubs
• 2.5 in. (64 mm) of grid mounting space
Video Distribution Hub
www.squared.com/multilink
Product Description IR Repeating System
Section 7–Video Distribution Hubs
The high headroom amplifier and bi-directional amplifier video hubs (models SDM38VBIR and SDM38VHIR) have integrated 5-volt IR engines that pass IR information, allowing control of any video device from any location by simply adding an IR target (model SDM1VIR), an IR emitter (model SDM2VIR), and a set top modulator to the system. For example, when the remote control is pointed at the IR target located at the television, the IR pulses are repeated by the emitter, which is controlling the DVD player in another location. IR information and power from the set top modulator are passed through port B only. When the modulator is connected to port A, IR remote control passing capability is not available and the video hub must be powered. All of the television ports can have targets connected. See the following figure.
IR
Gnd
+12vdc
Video hub (model SDM38VHIR)
B +Pwr
Modulators
Televisions
A
Set top modulator
IR target (model SDM1VIR)
IR emitter (model SDM2VIR)
Typical remote control
The single channel modulator (model SDM11VM), channel injectors (models SDM11VMB/SDM11VMH), and the modulator combiner (model SDM81VC) do not pass IR information for remote control. Use only a modulator with IR control, such as a set top modulator (model SDM41VTST, SDM21VTST, SDM41VT, or SDM21VT), and connect the set top modulator to the B+pwr input port of the video hub.
36
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Video Distribution Hubs Product Description Television Output Expansions A video hub can be connected to up to eight more video hubs, adding up to 64 television outlets. The longest recommended coaxial cable length should not exceed 150 ft (45.8 m) (total length from master hub to expansion hub and expansion hub to the television). NOTE: IR control can also be expanded using an IR control expander (ChannelPlus model 2181). Section 7–Video Distribution Hubs
For typical installation, see the figure below.
Master SDM38VHIR/VBIR
ChannelPlus model 2181 allows the SDM38VHIR/VBIR to expand IR control also. Use one 2181 for each SDM38VHIR/VBIR expansion. Expansion SDM38VHIR/VBIR
Expansion SDM38VHIR/VBIR
Modulator Combiner Hub (Model SDM81VC) The modulator combiner hub has inputs for eight modulators for distribution through a coaxial panel. The signals from all eight inputs are consolidated into a single output. The modulator combiner hub works like a zero-loss amplifier/combiner. The modulated signals that are put on the inputs will appear on the outputs with about 1dB of gain. When the output of the modulator combiner hub is connected to one of the modulator inputs of a video hub, signals will automatically appear on the video hub outputs at a legal FCC level. Features: • Combines modulator inputs from eight locations • Combines all channels into single output SDM81VC
• Accepts modulated inputs from 400–800 MHz • Modulator input expansion hub for models SDM38VBIR and SDMVHIR • 120 Vac power supply and adapter included • LED power indicator • 2.5 in. (64 mm) of grid mounting space
04/03
© 2001–2003 Schneider Electric All Rights Reserved
37
Video Distribution Hub
www.squared.com/multilink
General Information and Application Data GENERAL INFORMATION AND APPLICATION DATA
Section 7–Video Distribution Hubs
Troubleshooting Situation
Possible Solution
No picture
Check that the television and the modulator are tuned to the same channel. For example, if the modulator is broadcasting on UHF channel 16, make sure the television is on UHF 16 rather than CATV16. UHF 16 and CATV 16 are at different frequencies.
Weak UHF channel
If the television has a separate UHF input, be sure that it is connected.
Herringbone interference on modulator channel (diagonal lines)
• Move the modulator channel to another number. A low pass filter might need to be added to remove the cable company noise. • If the filter does not work, add a DC-block to remove common mode interference.
Herringbone interference on many channels, including modulator channels (disappears when you remove the CATV/antenna feed)
Use a variable attenuator and try to find a signal level where the interference just disappears. Sometimes, the problem is one station is stronger than the rest. In this case, attenuating all of the signals with a simple attenuator may cause the desired stations to be weak (snowy). Reduce the strength of only the offending station. A common FM trap will help if the problem is a nearby FM tower. If the problem is a nearby television station, usually the station management can provide suitable filters.
Audio volume is low
If you have a mono source, connect it to both right and left inputs using an RCA ‘Y’ connector. For proper audio level, both right and left inputs must be used.
No color on modulated channels
The incorrect cable standard might be in use. Not all televisions can accommodate the 1.25MHz frequency difference between the HRC and IRC cable standards.
FCC Requirements These products comply with FCC requirements. A system using these devices will comply with FCC requirements. Use only video modulators and modulator combiners that comply with Part 15 of the FCC rules and have 25 dBmV maximum output levels. Failure to do so may void the user’s authority to operate this equipment. The high headroom amplifier video hub (model SDM38VHIR) is suitable for use with an antenna or with CATV systems. The bi-directional amplifier video hub (model SDM38VBIR) is suitable for use with CATV systems only and has a bi-directional return path. The video amplifier hub (model SDM16VAB) is suitable for use with an antenna or CATV systems and also incorporates a bi-directional return path.
SPECIFICATIONS Passive Splitter The specifications for the video passive splitter portion of the combination hubs are shown in the following table. Parameter
Insertion Loss In-Out (dB maximum)
Return Loss Input (dB maximum)
Return Loss Output (dB minimum)
Isolation OUT-OUT (dB minimum)
Power Pass
38
Frequency (MHz)
Three-Way Splitter (SDM13VS)
Four-Way Splitter (SDM14VS
Eight-Way Splitter (SDM18VS) 10.5
5–40
5.3
6.7
40–400
5.5
6.9
11
400–500
5.8
7.2
11.5 12.3
500–600
6.1
7.5
600–1000
6.5
7.8
13
5–40
22
22
16
40–400
24
24
17
400–500
28
27
18
500–600
25
25
18
600–1000
24
23
18
5–40
21
24
16
40–400
23
26
20
400–500
25
24
20
500–600
24
25
21
600–1000
22
23
18
5–40
24
28
22
40–400
28
32
24
400–500
25
30
29
500–600
24
28
22
600–1000
23
25
20
500 mA
One port or all ports
Impedance
5–1000
75 ohms
RFI (dB)
5–1000
130 dB
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Video Distribution Hubs General Information and Application Data
Video Amplifier Hub (Model SDM16VAB) Specifications at 77 + 9 °F (25 + 5 °C) Output Run Distance (RG-6 coaxial):
Long
Short
150 ft (46 m)
75 ft (23 m)
Gain: CATV/Ant Input to Television Output
4 dB
1 dB
Television Output to CATV/Ant Input (5–42MHz reverse channel)
-8 dB
-12 dB
Forward
54–806 MHz
Reverse
5–42 MHz
Max CATV/Antenna Input (64 channels)
20 dBmV
Power Supply (SDM350086 included)
15 Vdc @ 300 mA
Section 7–Video Distribution Hubs
Bandwidth:
High Headroom Amplifier and Bi-directional Amplifier Video Hubs Specifications at 77 + 9 °F (25 + 5 °C) SDM38VHIR
SDM38VBIR
Output Run Distance (RG-6 Coaxial)
150 ft (46 m)
150 ft (46 m)
Modulator Input Distance
75 ft (23 m)
75 ft (23 m)
Gain: CATV/Ant Input to Television Output
3 dB
3 dB
Modulator Input to Television Output
-10 dB
-10 dB
Television Output to CATV/Ant Input (5–42MHZ reverse channel)
N/A
-15 dB
>80 dB
>35 dB
Forward
5–806 MHz
54–806 MHz
Reverse
N/A
5–42 MHz
Isolation: Modulator Input to CATV/Ant Bandwidth:
Max CATV/Antenna Input (64 channels)
20 dBmV
20 dBmV
Power Supply (SDM350086 included)
15 Vdc @ 300 mA
15 Vdc @ 300 mA
Modulator Combiner Hub (Model SDM81VC) Specifications at 77 + 9 °F (25 + 5 °C)
04/03
Number of Modular Inputs
8
Gain, Modulator Input to Output
~1 dB
Bandwidth
400–860 MHz
Nominal Modulator Input Level
25 dBmV
Maximum Number of Modulated Channels
16
Power Supply (SDM350086 included)
15 Vdc @ 300 mA
© 2001–2003 Schneider Electric All Rights Reserved
39
Video Distribution Hub
www.squared.com/multilink
Section 7–Video Distribution Hubs
General Information and Application Data
40
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Satellite Multi-Switch Product Description PRODUCT DESCRIPTION The satellite multi-switch (model SDM24VD) is a dual low noise block (LNB) connection switch for use with DIRECTV® and Dish Network® Dish 300 satellite systems. The satellite multi-switch is not suitable for use with Dish Network® Dish 500 satellite systems. The satellite multi-switch connects up to four satellite receivers to a dual LNB dish.
SDM24VD
The multi-switch locks one LNB to receive right-hand polarized signals and the other LNB to receive left-hand polarized signals. The individual satellite receivers can select any satellite channel. The multi-switch will automatically connect the satellite receivers to the correct LNB.
SATELLITE MULTI-SWITCH
• Dual LNB connections • Outputs to four satellite receivers • Compatible with DIRECTV® and Dish Network® Dish 300 systems • 950–1450 MHz • 2.5 in. (64 mm) of grid mounting space
GENERAL INFORMATION AND APPLICATION DATA Dual LNB 18 In. Satellite Dish For the installation of the dual 18 in. satellite dish to the satellite multi-switch, run two RG-6 coaxial lines from the satellite dish to the satellite multi-switch in the enclosure. Connect up to four RG-6 lines to the outputs of the satellite multi-switch. Each RG-6 coaxial line will connect to a satellite receiver. See the following figure.
LNB-A 13V
Satellite multi-switch (model SDM24VD)
LNB-B dish 18V
satellite receivers
Four standard satellite receivers
04/03
© 2001–2003 Schneider Electric All Rights Reserved
41
Section 8–Satellite Multi-Switch
Features:
Satellite Multi-Switch
www.squared.com/multilink
General Information and Application Data HDTV Dual-Dual LNB 24 In. Satellite Dish
Section 8–Satellite Multi-Switch
For the installation of an HDTV Dual-Dual LNB 24 in. satellite dish to the satellite multi-switch, run four RG-6 coaxial lines from the dish to the multi-switch included with the dish. From the multi-switch supplied with the dish, run two RG-6 coaxial lines to the Square D satellite multi-switch and two more RG-6 lines to two HDTV satellite receivers (each cable will connect to a receiver).The Square D satellite multi-switch can connect up to four more standard satellite receivers. See the following figure.
HDTV Multi-switch
LNB-A 13V
Satellite multi-switch (model SDM24VD)
Multi-switch included with satellite dish
LNB-B 18V
dish
satellite receivers
HDTV satellite receivers
Four standard satellite receivers
Satellite and Antenna Distribution For the highest performance of satellite and antenna or community antenna television (CATV) signals, the satellite and antenna (or CATV) signals should be kept separated. A second coaxial cable should run from each room that will have a satellite receiver. See the following figure.
LNB-B 18V
IR
dish
Gnd
LNB-A 13V
+15vdc
Antenna or CATV
B +Pwr satellite receivers
Modulators
Televisions
A
Satellite multi-switch (model SDM24VD)
42
Video hub (model SDM38VHIR)
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Satellite Multi-Switch General Information and Application Data
Satellite and Antenna Distribution Using Diplexers Diplexers combine satellite and antenna or CATV signals on a single coaxial cable.
Video hub
B +Pwr
(model SDM24VD)
Modulators
satellite receivers
(model SDM38VHIR)
Televisions
Section 8–Satellite Multi-Switch
LNB-B 18V
IR
dish
+15vdc
LNB-A 13V
Satellite multi-switch
Gnd
A diplexer will reduce the strength of the signals and increase the chance of noisy pictures. Coupling the two cables may also cause interference. It is recommended to only use diplexers when the user cannot run a second coaxial cable. See the following figure.
A
Coaxial cable Diplexer (not supplied by Square D) Single coaxial cable
Diplexer (not supplied by Square D) Satellite receiver
Expanding Satellite Outputs To expand the outputs, a second satellite multi-switch can be added to the system, allowing the use of up to six receivers. A third satellite multi-switch can be added, allowing the use of up to eight satellite receivers. See the following figure. Satellite multi-switches cannot cascade more than two layers (two additional multi-switch connections, shown below).
LNB-A 13V
Satellite multi-switch (model SDM24VD)
Satellite multi-switch (model SDM24VD)
04/03
LNB-A 13V
dish
satellite receivers
dish
LNB-B 18V
satellite receivers
LNB-B 18V
LNB-A 13V
dish
satellite receivers
LNB-B 18V
Satellite multi-switch (model SDM24VD)
© 2001–2003 Schneider Electric All Rights Reserved
43
Satellite Multi-Switch
www.squared.com/multilink
Section 8–Satellite Multi-Switch
General Information and Application Data
44
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Modulators Product Description PRODUCT DESCRIPTION The modulators have an internal quartz crystal reference oscillator and PLL circuitry to ensure drift-free reliable performance. With features such as DIP switch or push button channel programming and loop-through capabilities (except models SDM11VMH/SDM11VMB) for a monitor or VCR, the modules are user friendly.
MODULATORS
Single-Channel Digital Video Modulator (Model SDM11VM) The digital video modulator (model SDM11VM) is a digitally tuned video modulator that creates in-house television channels for a camera, DVD, satellite, or VCR by converting baseband video and audio signals to a user-selected UHF (off-air television channels 14 through 69) or Ultraband community antenna television (CATV channels 65 through 125). The modulator is compatible with video hub models SDM38VHIR and SDM38VBIR, supplied by Square D. For typical installation, see the figure below.
Section 9–Modulators
SDM11VM
Video hub (model SDM38VHIR) IR
Gnd
+12vdc
High Headroom Amp w/IR Engine
B +Pwr
Televisions
Modulators
CATV /Ant
A
Power supply-included (model SDM350086)
Connects to up to eight televisions RG-6 coaxial cable Audio inputs: Right and left are combined for monaural. Video input Input Output
Video modulator (model SDM11VM)
Power
Channel Select
Audio L Audio R
Single Channel Digital Modulator
Use the DIP switch to setup channel, mode (UHF or Cable), system (std, irc or hrc) and termination method.
Video
pll frequency
control
LED glows when power is applied
CCTV Camera or video source (CCTV Camera shown is not a Square D product)
Features: • RCA jack inputs video and audio • Digitally tuned • Creates television channel for camera or other video device • Channel range: CATV 65–125 (excluding 95–99) and UHF 14–69 • Compatible with SDM38V series • 25 dBmV output level • DIP switch programmable • Loop-through termination • FCC Part 15 compliant • Power supply and adapter included • LED power indicator • 2.5 in. (64 mm) of grid mounting space
04/03
© 2001–2003 Schneider Electric All Rights Reserved
45
Modulators
www.squared.com/multilink
Product Description Channel Injectors (Models SDM11VMH and SDM11VMB) The channel injectors create a new channel using audio and video signals received from a CAT-5/5E cable. Using a camera (model SDM1VC, SDM1VCC, SDM2VC, or SDM2VCC) or wall plate (model SDM1VWP), any audio/video device can be connected to the channel injector with a CAT-5/5E cable. Both models include push-button programming.
SDM11VMH
The injectors are designed to work with an existing installation, so additional hardware such as coaxial panels or coaxial wiring to the video source is not necessary. The community antenna television (CATV) or antenna coaxial cables are connected directly to the channel injector input. The channel injector distributes the new channel with antenna or CATV throughout the house using the existing coaxial cable. Any television connected to the channel injector will be able to view the antenna or CATV along with the newly created camera or video channel.
Section 9–Modulators
Features: • SDM11VMH is a combination modulator, high headroom amplifier, and isolator. The channel injector is used with antennas for off-air digital and analog television or CATV signals. • SDM11VMB is a combination modulator and bi-directional amplifier with a 5–42 MHz reverse channel. The reverse channel is used to support bi-directional CATV (cable modems, pay-per-view, and interactive cable). • CAT-5/5E inputs (screw down terminal block or RJ-45 jack) • Channel range: CATV 65–125 (excluding 95–99) and UHF 14–64 • Push button channel programming • FCC Part 15 compliant • 120 Vac power supply included • LED power indicator • 2.5 in. (64 mm) of grid mounting space Channel Injector and CAT-5/5E Cable Length Limitations The length of the CAT-5/5E cable that runs between the channel injector and the video cameras must not exceed the maximum cable lengths shown in the table below.
Cable Connection Length Limitations Connections From
46
To
Maximum Cable Length
Black and white camera (models SDM1VC and SDM2VC)
Channel Injector
300 ft (91.4 m)
Color camera (models SDM1VCC and SDM2VCC)
Channel Injector
100 ft (30.5 m)
Video wall plate (model SDM1VWP)
Channel Injector
100 ft (30.5 m)
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Modulators Product Description
Connecting the Channel Injector to a Camera or Video Wall Plate The channel injectors can be connected to a camera or a video wall plate. The video wall plate can be connected to the channel injector by two methods. The first method connects the camera or video wall plate with CAT-5 or CAT-5E cable directly to a CAT-5/5E data hub (model SDM8D) 110 punch-down block and then connects an RJ-45 patch cord (included) from the data hub RJ-45 jack to the channel injector. The second method connects the camera or video wall plate directly to the eight-position terminal block on the channel injector.
Section 9–Modulators
The channel injector was designed to work with CAT-5 or CAT-5E wiring. Although the system will function with quad wire, CAT-5 or CAT-5E wiring will deliver the highest quality picture and allows the use of an automatic line length sensor and picture compensator. See the figure below.
Power supply-included (model SDM350079)
Program
Channel injector (model SDM11VMH)
“Program” push button
CAT-5 video
CATV /Ant
Output
Power
Power the channel injector (model SDM11VMH) last. Make all the cable and CAT-5 connections first.
Channel Injector
Remove antenna or incoming cable from existing distribution and connect to channel injector (model SDM11) input.
Color bar Connect SDM11VMH output to distribution panel input (coaxial jumper included).
To four television wall plates
To camera or wallplate (model SDM1VCtypical installation)
OUT
IN
OUT
IN
IN
OUT
OUT
IN
OUT
IN
532-230 5MHzto 1000MHz SPLITTER
Existing distribution hub-typical installation (model SDM26P14V)
From Telco
COMBINER
Telephones
R T R 1 T 2
Combo Hub (2 lines
x 6 phones, 1input x 4 televisions) Square D model SDM26P14V
From telephone company
04/03
© 2001–2003 Schneider Electric All Rights Reserved
To wall plates
47
Modulators
www.squared.com/multilink
Product Description Set Top Modulators (Models SDM21VT, SDM21VTST, SDM41VT, and SDM41VTST) The set top digital modulators are frequency-agile and installer friendly. They are digitally tuned and convert any baseband video and audio signal to a user-selected UHF, or Ultraband CATV channel. They have push-button programming for setting the desired channel. They provide an output signal level of 25 dBmV.
Section 9–Modulators
SDM21VT and SDM41VT (Front view)
SDM21VT and SDM41VT (Back view)
Each set top modulator has a 5-volt IR engine and connections for IR emitters. When the modulators are used with a video distribution hub (models SDM38VHIR or SDM38VBIR), they allow remote television locations to have IR control of connected video components, such as DVDs, VCRs, and satellite receivers. An IR target (model SDM1VIR) would be required at each television location. An IR emitter (model SDM2VIR) would be required at each device being controlled. The set top modulators offer loop-through capability. Jumpers (75 ohm termination) are located on the side of each unit. When the terminator is removed, output signals can be looped to a local monitor or VCR. The MTS (Multichannel Television Sound) stereo sound modulators encode both audio channels using the MTS stereo standard. Stereo and surround sound information will be received by any MTS compatible television receiver.
Features: • SDM21VT and SDM21VTST have two inputs for modulating DVD, VCR, etc. SDM21VTST and SDM41VTST (Front view)
• SDM41VT and SDM41VTST have four inputs for modulating DVD, VCR, etc. • SDM21VTST and SDM41VTST maintain MTS stereo sound • 25 dBmV output level • 5-volt IR engines • Connections for IR emitters (model SDM2VIR) • Push button programming • Tuning range: UHF 14–64 and CATV 65–125 (excluding 95–99)
SDM21VTST and SDM41VTST (Back view)
• Drift free performance • FCC Part 15 compliant
48
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Modulators General Information and Application Data
GENERAL INFORMATION AND APPLICATION DATA
Situation
Possible Solution
No picture
• Verify that the video source is on and is producing a video signal. • Verify that the channel injector and camera or wall plate are wired properly. The CAT-5/5E colors must match the connector colors. • Check that the television and the modulator are tuned to the same channel. For example, if the modulator is broadcasting on UHF channel 16, make sure the television is on UHF 16 rather than CATV 16. UHF 16 and CATV 16 are at different frequencies.
Weak UHF channel
If the television has a separate UHF input, be sure that it is connected.
LEDs blink
Include one unused channel between modulated channels.The display will blink if you have chosen a channel that cannot be used.
Herringbone interference on modulator channel (diagonal lines)
• Move the modulator channel to another number. A low pass filter might need to be added to remove the cable company noise. • If the filter does not work, add a DC-block to remove common mode interference.
Use a variable attenuator and try to find a signal level where the interference just disappears. Sometimes, the problem is one station is stronger than the rest. In this case, attenuating all of the signals with a simple attenuator may Herringbone interference on many channels, including modulator channels cause the desired stations to be weak (snowy). Reduce the strength of the (disappears when you remove the CATV/antenna feed) only offending station. A common FM trap will help if the problem is a nearby FM tower. If the problem is a nearby television station, usually the station management can provide suitable filters. Audio volume is low
If you have a mono source, connect it to both right and left inputs using an RCA ‘Y’ connector. For proper audio level, both right and left inputs must be used.
No stereo (models SDM21VTST and SDM41VTST)
When using the television outputs to send audio to a home theater system, make sure the television is in the stereo mode for external speakers. Consult the television manual.
No color on modulated channels
The incorrect cable standard might be in use. Not all televisions can accommodate the 1.25MHz frequency difference between the HRC and IRC cable standards.
FCC Requirements These products comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: these devices may not cause harmful interference, and these devices must accept any interference received, including interference that may cause undesired operation. Installation Requirements FCC classifies this product under Part 15 of its rules as a "television interface device.” Systems designed using television interface devices have the following legal requirements: 1. The modulated channel signal strength may not exceed 15.56 dBmV at any television (Federal Regulation 47CFR15.115(b)(1)(i)). 2. If an antenna is used in the system, the modulated channel signal strength may not exceed -51 dBmV at the antenna input port (Federal Regulation 47CFR15.115(c)(4)). NOTE FOR INSTALLER: The system you design must comply with these regulations. As the installer, you are responsible. The easiest way to be fully compliant is to use a Square D video hub. Square D video hubs have the necessary isolation from the modulator input ports to the antenna input port and gain characteristic from the modulator input ports to the television output ports. These features will make your modulator installation comply with the above requirements. The typical installation shown on page 45 is fully compliant. The channel injectors have the necessary characteristics to comply with the requirements as designed without additional accessories. The model SDM11VMH is suitable for use with an antenna or with CATV systems.The model SDM11VMB is suitable for use with CATV systems only.
04/03
© 2001–2003 Schneider Electric All Rights Reserved
49
Section 9–Modulators
Troubleshooting
Modulators
www.squared.com/multilink
Technical Information TECHNICAL INFORMATION Programming Programming New Channels The new channel selected should be an unused channel. It should have no interference or trace of pictures, just “snow.” There must also be one unused channel above and below the selected channel to avoid interference. Programming a new channel with the channel injector (models SDM11VMH/SDM11VMB) and set top modulators (models SDM21VT/SDM21VTST and SDM41VT/SDM41VTST) is simple with the push button programming feature. For the channel injector (models SDM11VMH/SDM11VMB), the “Program” push button is used to enter the channel digits. For a programming example, see the following figure. The example uses channel 120. Section 9–Modulators
Step 1 Press program button
Step 2
1 time
Wait for power LED (ready for next number.)
Step 3 Press program button
2 more times
Step 4 Wait for power LED (ready for next number.)
Step 5 Press program button
10 more times
Step 6
(press 10 to enter a ‘zero’) LED comes back on when done. If an incorrect channel is entered, LED will flash quickly and return to the previous setting.
For the set top modulators, the “Select” push button is used to choose which modulator input channel to change (A, B, C, or D). Then, the new television channel is programmed using the “Program” push button. For a programming example, see the following figure. The example uses modulator input channel “B,” television channel 60.
Press “Select” button until channel LED is on
quad mts stereo surround
sound modulator
with IR output model H564
select A
B
C
program
D
IR pll frequency
select
A
B
C
control
program
Press “Program” button six times
D
select
A
B
C
program
D
Wait for channel “B” LED to light (ready for next number) select
A
B
C
program
D
Press “Program” button ten more times (press ten times to enter a zero) select
A
50
B
C
program
D
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Modulators Technical Information
Programming DIP Switches The DIP switch programming feature makes installing the video modulator (model SDM11VM) easy. To program the DIP switches, simply set the desired channel, mode, and termination. To program the video modulator, see the following figure.
14/65
30/81
46/102
62/118
15/66
31/82
47/103
63/119
16/67
32/83
48/104
64/120
17/68
33/84
49/105
65/121
18/69
34/85
50/106
66/122
19/70
35/86
51/107
67/123
20/71
36/87
52/108
68/124
21/72
37/88
53/109
69/125
22/73
38/89
54/110
23/74
39/90
55/111
UHF
24/75
40/91
56/112
25/76
41/92
57/113
26/77
42/93
58/114
CATV STD CATV IRC CATV HRC
27/78
43/94
59/115
28/79
44/100
60/116
LOOP
29/80
45/101
61/117
NORM
Section 9–Modulators
UHF/CATV
Programming Examples UHF channel 23, normal termination (75 ) Cable channel 116 (standard), loop through termination (Hi-Z) UHF channel 65, normal termination (75 ) Cable channel 65 (HRC), normal termination (75 )
04/03
© 2001–2003 Schneider Electric All Rights Reserved
51
Modulators
www.squared.com/multilink
Specifications SPECIFICATIONS Digital Video Modulator (Model SDM11VM) Specifications at 77 + 9 °F (25 + 5 °C)
Inputs
Video
1 Vp-p @ 75 Ω
Video Termination (switch selectable)
75 Ω in normal mode (NORM) >1 MΩ in loop through mode (LOOP) 1 Vrms @ 47 kΩ
Audio
Video Performance
Section 9–Modulators
RF Output
Power Supply
L and R inputs combined for monaural
Differential Gain
4%
Differential Phase
<4°
Signal/Noise
55 dB
Standard
UHF
CATV
Channel Ranges
14–69
65–125 (excluding 95–99)
Output Level
+25 dBmV (85 dBuV)
IM Distortion
-60 dBC
Alternate Channel
-45dBC @ 12 MHz
Model Number
SDM350086
Output Current
300 mA
Output Voltage
15 Vdc
Input Power
105–125 Vac
Channel Injectors Specifications at 77 + 9 °F (25 + 5 °C)
RF Gain Bandwidth Max CATV/Ant Input
SDM11VMH
SDM11VMB
CATV/Ant Input to Output
2 dB
2 dB
Output to CATV/Ant Input 5–42 MHz Reverse Channel
N/A
-4 dB
Forward
5–806 MHz
54–806 MHz
Reverse
N/A
5–42 MHz
(64 channels)
20 dBmV
Channel Ranges
RF Output
Video Performance
Power Supply
52
UHF
14–64
CATV
65–125 (excluding 95–99)
Output Level
+12 dBmV nominal
IM Distortion
-60 dBC
Alternate Channel
-45 dBC @ 12 MHz
Differential Gain
4%
Differential Phase
<4°
Signal/Noise
55 dB
Model Number
SDM350079
Output Current
600 mA
Output Voltage
15 Vdc
Input Power
105–125 Vac
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Modulators Specifications
Set Top Modulators (Models SDM21VT, SDM21VTST, SDM41VT, and SDM41VTST) Specifications at 77 + 9 °F (25 + 5 °C)
Video Performance
RF Output
Power Supply
Video
1 Vp-p @ 75 Ω
Audio
1 Vrms @ 47 kΩ
Differential Gain
4%
Differential Phase
<4°
Signal/Noise
55 dB
Standard
UHF
CATV
Channel Ranges
14–64
65–125 (excluding 95–99)
Output Level
+25 dB mV
IM Distortion
-60 dBC
Alternate Channel
-45 dBC @ 12 MHz
Modulator Model
SDM21VT
SDM41VT
SDM21VTST
Output Current
600 mA
900 mA
900 mA
900 mA
Model Number
SDM350079
SDM350082
SDM350082
SDM350082
Output Voltage
15 Vdc
Input Power
105–125 Vac
Frequency Range
20 Hz–12 kHz
MTS Audio Performance Signal/Noise (models SDM21VTST and Separation SDM41VTST) Surround Sound Noise Reduction
04/03
SDM41VTST
Section 9–Modulators
Inputs
65 dB 25 dB @ 1000 Hz compatible with Dolby full logic surround sound certified dbx
© 2001–2003 Schneider Electric All Rights Reserved
53
Modulators
www.squared.com/multilink
Section 9–Modulators
Specifications
54
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Video Cameras Product Description PRODUCT DESCRIPTION
VIDEO CAMERAS
Video Cameras (Models SDM1VC, SDM1VCC, SDM2VC and SDM2VCC) The cameras must be used with the companion channel injectors (models SDM11VMH or SDM11VMB). The video signal received from the camera is modulated by the channel injector to create a new channel to add to the existing television channels. The video camera is connected to the channel injector by a single run of CAT-5 or CAT-5E wire. Features: • SDM1VC and SDM1VCC are solid state, wide-angle cameras designed to fit in a single-gang junction box for exterior or interior installation SDM1VC or SDM1VCC
• SDM2VC and SDM2VCC are solid state, wide-angle cameras designed to fit double-gang junction boxes for exterior or interior installation
Section 10–Video Cameras
• Uses CAT-5/5E wire for use with the SDM11VM(H/B) series channel injector • 78° viewing angle coverage • Automatic white balance • NTSC format (models SDM1VCC and SDM2VCC) • EIA format (models SDM1VC and SDM2VC) • Weather resistant seals and a paintable brass finish (models SDM1VC and SDM1VCC) • Drip cap and gasket for outside installation (models SDM2VC and SDM2VCC) SDM2VC
• Smoked front panel (models SDM2VC and SDM2VCC) • Screw terminal connectors • Power is supplied by the channel injector
SDM2VCC
04/03
© 2001–2003 Schneider Electric All Rights Reserved
55
Video Cameras
www.squared.com/multilink
General Information and Application Data GENERAL INFORMATION AND APPLICATION DATA Camera Installation Weather Resistant Video Cameras (Models SDM1VC and SDM1VCC) The weather resistant video cameras are easily mounted into a single-gang junction box using the supplied single-gang gasket. The camera “looks” straight out from the cover plate. For a front door application, place the camera lens approximately 66 in. (1676.4 mm) off the ground, adjacent to the door. The camera lens cannot be adjusted. Camera plate Junction box
Gasket
Camera plate Gasket Junction box
Section 10–Video Cameras
CAT-5 or CAT-5E cable 6-32 x 1in. screws (included)
Standard single-gang junction box
In-Wall Video Cameras (Models SDM2VC and SDM2VCC) The in-wall video cameras can be installed inside or outside. For outside installation, the video camera is mounted in a two-gang junction box using the supplied drip cap and gasket. The camera works best when “looking” down on the subject. For a front door application, place the camera lens approximately 7 ft (2.1 m) off the ground, adjacent to the door. The camera lens can be adjusted up and down.
CAT-5 or CAT-5E cable
Drip cap Gasket Frame
Deep two-gang J-box
Add RTV to seal from weather 6-32 x 1in. screws (included) Insert top screws
Wire terminals and insert camera at an angle and rotate into place.
Frame Gasket Drip cap Attach drip cap, gasket, and frame
56
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Video Cameras General Information and Application Data
For interior installation, the video camera is mounted into drywall using the supplied CADDY® bracket. CADDY® bracket frame
Insert top screws
CADDY bracket
Video Camera Connection to Channel Injector Via Data Hub The video cameras can be connected to the channel injector by two methods. The first method is connecting the video camera directly to a CAT-5/5E data hub (model SDM8D) 110 punch-down block and running an RJ-45 patch cord (included) from the data hub RJ-45 jack to the channel injector RJ-45 jack. The second method is wiring the camera directly to the eight-position terminal block on the channel injector. When wiring to the eight-position terminal block, match CAT-5 or CAT-5E wires to top row of color block and remove the default resistor. If using quad wire, match wiring to bottom row of color bar and leave default resistor in place. DSL sent to home office computer only Ethernet connection from home office Four ethernet connections Data Hub ( 8 cables, TIA-568A)
Category 5 Compliant Square D model SDM8D
CAT-5 data hub (model SDM8D)
Power supply-included (model SDM350087)
Cable connecting to phone jack DSL from phone company
Ethernet hub (model SDM5DE)
Channel injector (model SDM11VMH)
Camera signal connects to channel injector by way of the RJ-45 patch cord Camera wire
Network hub 10 base-t Square D model H SDM5DE
Power Link/ normal
1
2
3
4
5
10 base-t hub
Cables connecting to data jacks in five wall plates
Antenna or incoming cable
Program CAT-5 video
Output
CATV /Ant
Power
Power supply (model SDM350079)
Channel Injector
04/03
© 2001–2003 Schneider Electric All Rights Reserved
57
Section 10–Video Cameras
Drywall
Video Cameras
www.squared.com/multilink
General Information and Application Data NOTE: The channel injector was designed to work with CAT-5/5E wiring. Although the system will function with quad wire, CAT-5/5E wiring will deliver the highest quality picture and allows the use of an automatic line length sensor and picture compensator. Painting the Cover Plate of Weather Resistant Cameras The brass cover plate can be painted to match any exterior house paint. The brass cover plate is ready to paint after sanding and applying exterior use metal primer. Channel Injector and CAT-5/5E Cable Length Limitations The length of the CAT-5/5E cable that runs between the channel injector and the video cameras must not exceed the maximum cable lengths listed in the table below. Cable Connection Length Limitations Connections
Section 10–Video Cameras
Maximum Cable Length From
To
Black and white camera (SDM1VC and SDM2VC)
Channel Injector or CAT-5/5E data hub
300 ft (91.4 m)
Color camera (SDM1VCC and SDM2VCC)
Channel Injector or CAT-5/5E data hub
100 ft (30.5 m)
FCC Requirements These products comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: these devices may not cause harmful interference, and these devics must accept any interference received, including interference that may cause undesired operation. Installation Requirements FCC classifies this product under Part 15 of its rules as a "television interface device.” Systems designed using television interface devices have the following legal requirements: 1. The modulated channel signal strength may not exceed 15.56 dBmV at any television (Federal Regulation 47CFR15.115(b)(1)(i)). 2. If an antenna is used in the system, the modulated channel signal strength may not exceed -51dBmV at the antenna input port (Federal Regulation 47CFR15.115(c)(4)). NOTE TO INSTALLER: The system you design must comply with these regulations. As the installer, you are responsible. The video cameras (when used with an SDM11VMH or SDM11VMD channel injector) have the necessary characteristics to comply with the above requirements as designed without additional accessories. The model SDM11VMH is suitable for use with an antenna or with CATV systems.The model SDM11VMB is suitable for use with CATV systems only.
58
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Video Cameras Technical Information
TECHNICAL INFORMATION Programming Once a video camera is connected to a channel injector, programming a new channel with the channel injector (model SDM11VMH or SDM11VMB) is simple with the push button programming feature. The “Program” push button is used to enter the channel digits. For a programming example, see the following figure. The example uses channel 120.
Step 1 Press program button
Step 2
1 time
Wait for power LED (ready for next number.)
Step 3 Press program button
2 more times
Section 10–Video Cameras
Step 4 Wait for power LED (ready for next number.)
Step 5 Press program button
10 more times
Step 6
(press 10 to enter a ‘zero’) LED comes back on when done. If an incorrect channel is entered, LED will flash quickly and return to the previous setting.
SPECIFICATIONS Video Cameras Specifications at 77 + 9 °F (25 + 5 °C) SDM1VC Image Format
04/03
SDM2VC
EIA (black and white)
Resolution, Horizontal
525 lines
Resolution
350 lines
Minimum Illumination
0.3 lux
Signal to Noise Ratio
>45 dB
AGC
Yes
Lens
3.6 mm F2.0
Lens Viewing Angle
78°
White Balance
automatic
Electronic Shutter Speed
1/60 to 1/50,000 second
SDM1VCC
SDM2VCC
NTSC (color)
2 lux
Maximum Cable Length to Channel Injector or CAT-5/5E Data Hub
300 ft (91.4 m)
Ambient Temperature Operating Range
-10° C to +50° C (+14° F to +122° F)
© 2001–2003 Schneider Electric All Rights Reserved
6 lux
8 lux
100 ft (30.5 m)
59
Video Cameras
www.squared.com/multilink
Section 10–Video Cameras
Specifications
60
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Video Wall Plate Product Description PRODUCT DESCRIPTION
VIDEO WALL PLATE
Video Wall Plate (Model SDM1VWP) The video wall plate (model SDM1VWP) is a companion piece to the channel injector module. Using the video wall plate, any audio/video device with RCA connections can be connected to the channel injector using a single run of CAT-5 or CAT-5E wire. No coaxial cables or additional power wires are needed. The video wall plate provides switchable 75 ohm or Hi-Z termination for loop-through capability. The looped video output can be fed to a local monitor or VCR. Features: • Uses CAT-5/5E wire for use with SDM11VM(B/H) series channel injectors • Switchable 75 ohm, or Hi-Z terminations for loop-through • Looped video output for monitor or VCR • Uses Decora style wall plates • Accepts any type of video input from a camera or other video device with RCA connections SDM1VWP
GENERAL INFORMATION AND APPLICATION DATA Connecting Video Wall Plate to Video Source Satellite receiver
The video wall plate connection to a video source is completed using RCA type connector cables.
Audio/video outputs
Operating Controls
Video wall plate (model SDM1VWP)
Control
Description
POWER
The green power LED will be lit showing active power when the power supply is plugged into either the video wall plate or the channel injector.
NORM
Select NORM when a television or audio/video receiver is not used at the wall plate to view the connected source. The NORM position terminates the video source with 75 Ω .
LOOP
Select LOOP when a television or audio/video receiver is connected to the wall plate to view the connected source. The LOOP position leaves the source unterminated. The local monitor will provide termination.
AUDIO R
AUDIO L
VIDEO
Local television N O R M
L O O P
POWER
NOTE: When the video wall plate is wired to a channel injector, the channel injector and the video wall plate can be powered from either location. However, the video wall plate does not come with a source of power, so the power supply from the channel injector must be used.
Video input
12:00
Audio inputs Audio receiver
POWER
04/03
N O R M
L O O P
© 2001–2003 Schneider Electric All Rights Reserved
61
Section 11–Video Wall Plate
• Uses screw terminal connectors (in rear, for CAT-5/5E termination)
Video Wall Plate
www.squared.com/multilink
General Information and Application Data Video Wall Plate Connection to Channel Injector
Channel injector (model SDM11VMH or SDM11VMB)
CAT-5 v ideo
Power the channel injector (model SDM11VMH or SDM1VWP) last. Make all cables and CAT-5 connections first. Connect antenna or incoming cable to channel injector (model SDM11VMH) input.
CAT-5 cable
Connect channel injector (model SDM11VMH) output to splitter or distribution panel input. Video wall plate (model SDM1VWP) (Rear view)
The video wall plate can be connected to the channel injector by two methods. The first method is by connecting the video wall plate directly to a CAT-5/5E data hub (model SDM8D)110 punch-down block and running an RJ-45 patch cord (included) from the data hub RJ-45 jack to the channel injector RJ-45 jack. The second method is wiring the video wall plate directly to the eight-position terminal block on the channel injector. When wiring to the eight-position terminal block, match CAT-5 or CAT-5E wires to top row of color block and remove default resistor. If using quad wire, match wiring to bottom row of color bar and leave default resistor in place. NOTE: The channel injector was designed to work with CAT-5/5E wiring. Although the system will function with quad wire, CAT-5/5E wiring will deliver the highest quality picture and allows the use of an automatic line length sensor and picture compensator. Channel Injector and CAT-5/5E Cable Length Limitations
Section 11–Video Wall Plate
The length of the CAT-5/5E cable that runs between the channel injector and the video wall plate must not exceed 100 ft (30.5 m). FCC Requirements These products comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: these devices may not cause harmful interference, and these devics must accept any interference recieved, including interference that may cause undesired operation. Installation Requirements FCC classifies this product under Part 15 of its rules as a “television interface device.” Systems designed using television interface devices have the following legal requirements: 1. The modulated channel signal strength may not exceed 15.56 dBmV at any television (Federal Regulation 47CFR15.115(b)(1)(i)). 2. If an antenna is used in the system, the modulated channel signal strength may not exceed -51dBmV at the antenna input port (Federal Regulation 47CFR15.115(c)(4)). NOTE TO INSTALLER: The system you design must comply with these regulations. As the installer, you are responsible. The video wall plate (when used with an SDM11VMH or SDM11VMB channel injector) has the necessary characteristics to comply with the above requirements as designed without additional accessories. The model SDM11VMH is suitable for use with an antenna or with CATV systems.The model SDM11VMB is suitable for use with CATV systems only.
62
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
IR Target and Emitter Product Description PRODUCT DESCRIPTION IR Target (Model SDM1VIR) Features: • Controls DVD, VCR and DSS players • 5-volt target • Locate at television
SDM1VIR
IR Emitter (Model SDM2VIR) Features: • Controls DVD, VCR and DSS players • 5-volt emitter • Compatible 12- and 5-volt IR systems SDM2VIR
• Adhesive backed single head emitter • Locate at video source
IR Repeating System
IR TARGET AND EMITTER
The high headroom amplifier and bi-directional amplifier video hubs (models SDM38VBIR and SDM38VHIR) and the set top modulators (models SDM21VT, SDM41VT, SDM21VTST, and SDM41VTST) have integrated 5-volt IR engines that pass IR information, allowing remote control of any video device from any location when the IR target and IR emitter are used. To control the video devices, an IR target (model SDM1VIR) and an IR emitter (model SDM2VIR) are connected to the modules. For example, when the remote control is pointed to the IR target located at the television, the IR pulses are repeated by the emitter, which is controlling the DVD player located in a remote area.
IR
Gnd
+12vdc
Video hub (model SDM38VHIR)
B +Pwr
Modulators
Televisions
A
Set top modulator
IR target (model SDM1VIR)
IR emitter (model SDM2VIR)
04/03
© 2001–2003 Schneider Electric All Rights Reserved
Typical remote control
63
Section 12–IR Target and Emitter
GENERAL INFORMATION AND APPLICATION DATA
IR Target and Emitter
www.squared.com/multilink
Section 12–IR Target and Emitter
General Information and Application Data
64
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Accessories Product Description PRODUCT DESCRIPTION Low Pass Filter (Model SDM600LPF) Features: • Used to “clear” channels so that modulated signals can be added to the system • Filter begins to remove programming starting at channel 85 • Modulated signals can be added above channel 91 Video Signal Attenuator (Models SDM2503 and SDM2506) Features: • Used to reduce signal strength
SDM1A
• SDM2503 reduces signal by 3dB • SDM2506 reduces signal by 6dB Amplifier Adapter (Model SDM1A) The adapter mounts to any enclosure grid. The adapter allows ChannelPlus amplifiers (models 3400 and 8200) to mount into the enclosure grid. The adapter requires 2 in. (51 mm) of grid mounting space in the enclosure.
SDM6A
Section 13–Accessories
Six-Connector Adapter (Model SDM6A) The adapter allows for a combination of eight keystone connectors (CAT-5/5E) or six coaxial barrel connections. The adapter requires 2 in. (51 mm) of grid mounting space in the enclosure. Features: • Mounts to any enclosure grid • Eight CAT-5/5E connectors • Six coaxial connectors Isolation Mounting Brackets (Models SDM1IMB and SDM2IMB) Features: • Universal mounting plate for products that are not Square D Multi-Link brand SDM1DC
• Works with audio multi-zone amps, security panels and home automation controllers • Adjustable for mounting patterns from 4.5 in. (114.3 mm) to 10.5 in. (266.7 mm) wide • Heavy duty bracket (model SDM1IMB) load rated 60 pounds • Light duty bracket (model SDM2IMB) load rated 10 pounds • Isolated to prevent ground loops CAT-5/5E Patch Cords (Models SDM1DC and SDM2DC)
SDM2DC
04/03
The patch cords are available in two sizes, a one foot cord and a two foot cord. The cords can be used with data hubs (models SDM8D, SDM8DB, and SDM5DE), telephone hubs (models SDM46P and SDM48PX), and channel injectors (models SDM11VMH and SDM11VMB).
© 2001–2003 Schneider Electric All Rights Reserved
65
Accessories
www.squared.com/multilink
Product Description Coupling Tube (Model SDM2C) Features: • Stack multi-link enclosures • 2 in. (59 mm) conduit size passes cables from enclosure to enclosure • No limits on number coupled • Automatically spaces enclosure 2 in. (59 mm) apart • Use up to four coupling tubes per enclosure Replacement Snap Locks (Model SDM10SL) Features: • Ten replacement snap locks per package Power Supply Channel Injectors and Two-Input Set Top Modulators (Model SDM350079) Used on the following modules: • Channel injectors (models SDM11VMB and SDM11VMH) • Dual set top modulator (model SDM21VT) Four-Input and MTS Stereo Set Top Modulators (Model SDM350082)
Section 13–Accessories
Used on the following modules: • Quad set top modulator (model SDM41VT) • Dual and quad MTS stereo sound set top modulators (models SDM21VTST and SDM41VTST) Video Hubs (Model SDM350086) Used on the on the following modules: • Video hubs (models SDM38VBIR and SDM38VHIR) • Modulator combiner (model SDM81VC) • Video amplifier hub (model SDM16VAB) • Video modulator (model SDM11VM) Ethernet Hub (Model SDM350087) Used on the Ethernet hub (model SDM5DE). Adapter Cable (Model SDM532172) Used on the following modules: • Video hubs (models SDM38VBIR and SDM38VHIR) • Modulator combiner (model SDM81VC) • Video amplifier hub (model SDM16VAB) • Video modulator (model SDM11VM)
66
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Accessories Product Description Wire Spacer (Model SDM12WS) Features: • Connects to the grid on SDM18BW or SDM36BW enclosures • Lifts modules one inch (25.4 mm) above the grid • Repeats grid pattern • Provides wire management channel • 11.2 in. (285 mm) high and 6.5 in. (165.1 mm) wide The wire spacer, due to panel depth limitations, cannot be used to mount the following modules: • Video hubs (models SDM38VHIR/BIR) • Modulator combiner (model SDM81VC) • Modulator (model SDM11VM) • Channel injectors (models SDM11VMH/MB) • Satellite multi-switch (model SDM24VD)
SDM12WS
• Accessory adapters (models SDM1A or SDM6A)
Section 13–Accessories
• Video splitter (model SDM18VS)
04/03
© 2001–2003 Schneider Electric All Rights Reserved
67
Accessories
www.squared.com/multilink
Section 13–Accessories
Product Description
68
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Troubleshooting General Troubleshooting Techniques
GENERAL TROUBLESHOOTING TECHNIQUES TROUBLESHOOTIN G
Multi-Link products are designed for easy, trouble-free installation and connection. Any problems encountered with Multi-Link structured wiring installations can most likely be attributed to the situations that are outlined in the table below. To ensure a properly working system, it is recommended to test each connection during the installation process. If it is necessary to troubleshoot a Multi-Link installation, follow these guidelines to make the troubleshooting process easier: • Start at the demarcation point of the system. • Don’t overlook the obvious. For example, make sure all the power supplies are connected. • Temporarily remove as many Multi-Link products as possible from the system to focus on the specific problem. • Connect each modulator or video hub directly to a television to verify each Multi-Link product is working properly.
RADIO FREQUENCY TROUBLESHOOTING TECHNIQUES Thin Rolling Lines or Herringbone Patterns on Many Channels Cause
Solution
Signal strength at television is too high. Usually caused by an over-driven amplifier.
Add one or more in-line attenuators (Multi-Link catalog numbers SDM2503 or SDM2506, see page 65 for more information).
Cause
Solution
Bad coaxial runs.
Check coaxial cable for damage. Replace F-connectors.
Section 14–Troubleshooting
Snowy Channels
Thick Video Bars Cause
Solution
Interference from AC power.
Move coaxial cable runs at least 1 ft (.31m) away from AC wiring, HID or florescent lighting ballasts, ground wires and lightning rods.
Hum Cause
Solution
Bad power supply.
Replace power supply on affected Multi-Link amplifier or modulator.
Dark Band Moves Up Screen Cause
Solution
Bad power supply.
Replace power supply on affected Multi-Link amplifier or modulator.
No Infrared Control Signals Cause
Solution
Disconnect all IR products. Reconnect one at a time to identify shorted Either a short in infrared control products (catalog numbers SDM1VIR product. Replace shorted IR product. Also replace any non-IR/DC passing and SDM2VIR) or a non-IR/DC passing splitter is installed in the system. splitters in the system.
Multiple Channels Not Displayed by Television Cause
Solution
Too narrow bandwidth on coaxial and/or splitters. Also, television tuner may not be able to accept higher channels (a problem with older television sets).
Use RG-6 coaxial cable. Make sure bandwidth of Multi-Link splitters and amplifiers match incoming system frequency range; replace with higher bandwidth products if needed.
Television Will Not Receive Modulated Signal When Cable Box is Used Cause
Solution
Some Cable Company Boxes will not pass modulated signals.
Install a 2-way splitter ahead of cable box. Connect one side of 2-way splitter to cable box. Connect the other side to a high pass filter (Channelplus catalog number C-BCK). Use another 2-way splitter to combine the output of the cable box with the output from the high pass filter and connect combined signal to television.
Modulated Channels Exhibit Ghosting
04/03
Cause
Solution
Interference from cable or off-air programming. Also possible result of inadequate coaxial cable.
Make sure coaxial cable has adequate shielding. Also see Modulator Troubleshooting below.
© 2001–2003 Schneider Electric All Rights Reserved
69
Troubleshooting
www.squared.com/multilink
General Troubleshooting Techniques RADIO FREQUENCY TROUBLESHOOTING TECHNIQUES (CONTINUED) Modulated Channel Displays all Snow on Television Cause
Solution
Television tuner and modulator are not set on the same mode (UHF vs VHF). See Modulator Troubleshooting below.
Modulated Channel is a Black Picture on Television Cause
Solution
Modulator is working, but connections from video source to modulator are incorrect.
Make sure video source is powered. Verify good connections from video source (VCR, DVD, etc.) to modulator. Verify video source is working by connecting directly to television. Also see the section Modulator Troubleshooting for Cameras below.
Modulated Channel Exhibits Herringbone Patterns Cause
Solution
Interference from cable or off-air programming.
See the section Modulator Troubleshooting for Cameras below.
MODULATOR TROUBLESHOOTING FOR CAMERAS If the modulated channel is not displayed on the television or if the modulated channel is displayed on the television but exhibits ghosting or herringbone patterns, follow the guidelines below: 1. Make sure the channel programmed on the modulator matches the mode to which the television is set. For example, if the modulator is programmed to a channel between channel 14 and channel 69, then make sure the television is set for off air programming. If the modulator is programmed to a channel between channel 69 and channel 125, make sure the television is set for cable television.
Section 14–Troubleshooting
2. With the modulator disconnected from the structured wiring system and the incoming cable or antenna signal connected to the structured wiring system, run the autoprogram on the television set. Autoprogram will detect all “used” channels. Make sure the modulator is programmed to a channel which autoprogram did not detect, i.e., an “unused” channel. 3. Connect the modulator output directly to one television and remove the cable or antenna signal from the structured wiring system. 4. If the modulated signal is displayed on the television, then the incoming cable or antenna signal is interfering with the modulated signal. To correct this problem, a filter must be inserted on the incoming signal to clear any cable signal from desired modulated channel. For the filter, see page page 65. 5. If, when the cable or antenna signal is removed from the structured wiring system, the modulated signal does not show up on the television, then the problem may lie with the television set or a cable run. With the cable or antenna signal removed, connect the modulator output to another television set. If the problem still exists, check the relevant coaxial runs for any damage or improperly installed connectors.
70
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Glossary Structured Wiring Terms
STRUCTURED WIRING TERMS Adjacent channels Two television channels having video carriers 6 MHz apart or two FM channels having carriers occupying neighboring allocations. ADSL (Asymmetrical Digital Subscriber Line) Providing a high-speed Internet connection via an incoming telephone line and modems. Amplifier A device used to increase the power and voltage level of a signal. ATSC (Advanced Television Systems Committee) An international organization establishing voluntary technical standard for advanced television systems. Attenuation The decrease in magnitude of a signal as it travels through a transmission medium such as a coaxial cable. Attenuator A passive device used to reduce signal strength. Bandwidth The range of frequencies required for proper transmission of a signal. Expressed in Hertz (cycles per second). The higher the bandwidth, the more information that can be carried. Baseband A transmission method in which the entire bandwidth is used to transmit a single digital signal. The signal has not been modulated onto a carrier (i.e. Hi-Fi Audio, NTSC video, or RS-232 data). BID (Bi-directional) Systems used with CATV services using pay-per-view or cable modems. BID is not for use with off-air antennas. Bit One binary digit.
Broadband A transmission method having a bandwidth sufficient to carry multiple voice, video, or data signals simultaneously. Each channel is modulated to a different frequency bandwidth on the transmission medium and is demodulated to its original frequency at the receiving end. This technique is used to provide many CATV channels on one coaxial cable. Category rated Twisted pair communications circuits are rated by category, whose specifications are covered under EIA/TIA 568. The higher the category number, the higher the information capacity of the circuit. Category 5 See “Category Rated.” For modern telephone/data transmission, Category 5, 4-UTP (four unshielded twisted wire pairs) is recommended. Data transmission at frequencies up to 100 MHz. Category 5E See “Category 5.” Improved specifications for near-end cross talk and attenuation. CATV (Community Antenna Television, cable television) A radio frequency distribution system which distributes television broadcast programs, original programs, premium programming and other services using a network of coaxial cable. Channel In television, a portion of the radio frequency spectrum that is 6 MHz wide and carries the audio and video carriers of the television signal. CO (Central Office) A reference to the local telephone exchange carrier. Coaxial cable A concentric cable consisting of a center conductor, a dielectric, and a shield. Coaxial cable is used for most MATV and CATV work and has a characteristic impedance of 75 ohms. Composite video signal The composite video signal including the picture (luminance) signal, the blanking and sync pulses, and the color (chrominance). Cross connect The physical connection between patch panels or punch-down blocks that facilitates connections from systems and feeds to drops.
04/03
© 2001–2003 Schneider Electric All Rights Reserved
71
Section 15–Glossary
BPS (Bits Per Second) A measurement of data transmission speed.
Glossary
www.squared.com/multilink
Structured Wiring Terms Crosstalk The unwanted introduction of signals from one channel to another. Daisy Chain Wiring A wiring concept where multiple terminations of a branch wiring run are “looped” in parallel, interconnecting one location to the next. Decibel Abbreviation dB. A logarithmic function used to simplify MATV calculations. Decibels may be added or subtracted. 0 dB is the standard reference level for all MATV calculations. dB See “Decibel.” dBmV An absolute signal level where 0 dBmV is equal to 1000 µV across 75 ohms. Demarc (Demarcation Point) The point of interconnection between telephone company facilities and a building’s wiring. Diplexer A device that combines RF frequencies (OFF-air or CATV) and satellite frequencies onto a single coaxial cable. Another diplexer would also be required to separate the signals at the point of use. DIP switch (Dual Inline Package Switch) A manual means of selecting settings on an electronic circuit board. DSL (Digital Subscriber Line) A service that offers a faster Internet connection than a standard dial-up connection. DSL technology uses existing two-wire copper telephone wiring to deliver high-speed data services to homes and businesses. Egress A condition often called “signal leakage” in which signals carried by the distribution system radiate into the air. EIA (Electronic Industry Association-formerly RMA or RETMA) An association of manufacturers and users that establishes standards and publishes test methodologies.
Section 15–Glossary
Ethernet Ethernet is a LAN (Local Area Network) technology protocol that transmits information between computers and peripherals at speeds of 10 and 100 Mbps (fast Ethernet). Currently, the most widely used version of Ethernet technology is the 10 Mbps. F-connector A barrel-type connector used to terminate coaxial cable, such as RG-59, RG-6, or RG-6Q, for video applications. Filter Filters are used to block out undesired frequencies. There are two types of filters: band pass and rejection. A band pass filter permits only the desired range to pass through, while the rejection filter attenuates and undesired range of frequencies. Gain A measure of amplification of a device, usually expressed in dB at the highest frequency of operation. Ghosting A signal interference condition producing positive or negative pictures displaced in time from the desired picture, caused by multi-path signal reception. Ghost pictures also result from cable ringing. GigaHertz (GHz) A unit of measurement of frequency or bandwidth of one billion cycles per second. HAN (Home Area Network) See “LAN.” HDTV (High Definition Television) A high-resolution, wide-screen common picture format and transmission standard for bringing digital broadcast television to the home. Head end The equipment located at the start of a CATV system. The place where the signals are processed and combined prior to distribution. Hertz (Hz) The unit of measurement of frequency or bandwidth of one billion cycles per second. HHR A high headroom amplifier used in high performance off-air antenna or non bi-directional CATV systems. Homerun Wiring A wiring concept in which all branch wiring is run back to a central hub, or service entrance location. Hub A central point to connect and distribute common information to multiple locations.
72
© 2001–2003 Schneider Electric All Rights Reserved
04/03
www.squared.com/multilink
Glossary Structured Wiring Terms
IDC (Insulation Displacement Connector) A type of wire terminating in which the wire is “punched down” into a metal holder which cuts into the wire insulation, making contact with the conductor. Ingress A condition where unwanted RF signal leaks into a distribution system. Insertion loss Also called “feed through loss.” This is the loss that occurs as signals pass through a passive device. Insertion loss occurs in all devices which do not amplify the signal. IR signal Infrared signal, used to transmit functional commands to a remotely located device, such as a television, DVD, or VCR. ISDN (Integrated Services Digital Network) Provides a user up to 56 kpbs of data bandwidth on a telephone line that is also used for voice, or up to 128 kbps if the line is only used for data. KiloHertz (KHz) A unit of measurement of frequency or bandwidth of one thousand cycles per second. LAN (Local Area Network) A group of computers and peripherals set up to communicate with each other. LNB A low noise bandpass amplifier is located in the feed horn of a satellite dish and receives satellite signals that are reflected from the dish. MATV (Master Antenna Television System) A distribution system which is usually contained within a single building and receives its signals from an antenna or CATV system. Megabits (Mbps) Megabits (one billion bits) per second, a measurement of transmission speed. MegaHertz (MHz) A unit of measurement of frequency or bandwidth of one million cycles per second. Modulation Placing information, audio/video, onto a higher frequency carrier by means of amplitude, frequency, or phase adjustment. Section 15–Glossary
MTS (Multi-Television Stereo) NID (Network Interface Device) NTSC (National Television System Committee) A national organization formed to establish standards with regards to commercial television transmissions. Off-air Any channel which can be received by a conventional antenna system, including VHF and UHF broadcasts. Patch cords The cords interconnecting terminations at the central distribution panel. Typically these cords are terminated with modular plugs. Punch-Down block Refer to “110 Connector.” RF (Radio Frequency) Generally refers to data modulated over a high-frequency carrier for wireless transmission. RFI (Radio Frequency Interference) RG-6 cable A coaxial cable used for broadband video applications. RG-6 has an 18 gauge center conductor, allowing a higher bandwidth than the RG-59 cable, which has a smaller 20 gauge center conductor. RG-6 uses standard “F” connectors for video equipment connections. RG-6Q cable Quadruple, or “Quad Shield” cable, doubles the shielding of a standard RG-6 cable, using a second layer of foil and aluminum braid. RJ-11 Voice grade modular interface (jacks and plugs), accepts one pair of conductors. Commonly used for single line telephones, answering machines, and modems.
04/03
© 2001–2003 Schneider Electric All Rights Reserved
73
Glossary
www.squared.com/multilink
Structured Wiring Terms RJ-14 Voice grade modulator interface (jacks and plugs), accepts two pairs of conductors. Commonly used for dual line telephones and answering machines. RJ-25 Voice grade modular interface (jacks and plugs), accepts three pairs of conductors. Commonly used for KTS (Key Telephone System), a system that provides direct selection of an available line from a multiline telephone set. RJ-31X Modular interface (jacks and plugs), used with security systems only. RJ-45 Voice/data grade modular interface (jacks and plugs). Offering four pairs of connectors, RJ-45 is the interface of choice for all structured wiring installations. Signal-to-noise ratio (SIN) The ratio of desired signal level to the undesired noise level, expressed in dB. Signal strength The intensity of an RF signal measured in volts (V), millivolts (mV), microvolts (µV), or dBmV. Snow A large quantity of random noise in a television picture which results from a poor CON (earner-to-noise) ratio. Star Topology Wiring See “Homerun Wiring.” Tap A device inserted into a feeder line which allows a specific amount of signal to be removed from the feeder line and isolates the TAP port from the main through line. Terminator A resistive device which matches a cable, or the unused output of an active or passive system component to its characteristic impedance. Proper termination is required to prevent unused outputs from causing reflections back down the line.
Section 15–Glossary
TIA (Telecommunications Industry Association) Body which authored the TIA/EIA 568-A “Commercial Building Telecommunications Wiring Standard” in conjunction with EIA. Tilt A linearized change in the frequency response of the CATV system caused primarily by the frequency dependent cable loss. Tilt is quantified by comparing the difference between the level of the highest channel’s video carrier and that of the lowest channel. UHF (Ultra High Frequency) Off-air television channel 14 through 69. UTP (Unshielded Twisted Pair) Twisted pair cable without either individual or overall shielding. VHF (Very High Frequency) Off-air television channels 2 through 13. 10 BASE-T 10 Mbps 802.3/Ethernet over standard unshielded twisted pair cable specification. 10 BASE-T supports network configurations over twisted pair transmission systems up to 100 meters in length without the use of a repeater. 100 BASE-T See “10 BASE-T,” except rated for 100 Mbps (fast Ethernet). 110 connector An Insulation Displacement Connection (see “IDC”) system used to terminate telephone and data cables. Commonly referred to as a 110 connector or 110 punch-down. A 110 punch-down tool is required to terminate the cable in the connector terminals.
74
© 2001–2003 Schneider Electric All Rights Reserved
04/03
Index
A Index
accessories adapter cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 amplifier adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 CAT-5/5E patch cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 coupling tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 isolation mounting brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 low pass filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 replacement snap locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 six-connector adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 wire spacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
B bridgeable CAT-5/5E hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
C CAT-5 jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Category 5 and 5E cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 channel injectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46–47, 50, 52 combination hubs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
data termination hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 dual LNB 18 in. satellite dish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
E enclosures and brackets AC power accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21–23 cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 20, 22–23 universal mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Ethernet hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29–30
G glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71–74
H HDTV dual-dual LNB 24 in. satellite dish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
04/03
© 2001–2003 Schneider Electric All Rights Reserved
75
Section 16–Index
D
Index
I IR emitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 IR target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
M modular connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 modulator combiner hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37, 39 modulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
P power supply channel injectors and two-input set top modulators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Ethernet hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 four-input and MTS stereo set top modulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 video hubs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 pre-wire schemes audio/video and television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 telephone and video camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 telephone wall plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 product configurations advanced home office . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Section 16–Index
advanced video and security camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 basic home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 basic home office . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 media center and security camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 punch-down connectors (110) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
R RG-6 coaxial cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
76
© 2001–2003 Schneider Electric All Rights Reserved
04/03
Index
S satellite and antenna distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 satellite and antenna distribution using diplexers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 satellite multi-switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 satellite outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 set top modulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48, 50, 53 single-channel digital video modulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45, 51–52 speaker distribution hub. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 splitter hubs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26, 33, 38
T telephone expansion hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 telephone interface hub/patch panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 telephone master hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
V video amplifier hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33–34, 38–39 video cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55–59 video distribution hubs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 video signal attenuator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 video wall plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61–62 Section 16–Index
voice and data network hubs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
04/03
© 2001–2003 Schneider Electric All Rights Reserved
77
Section 16–Index
Index
78
© 2001–2003 Schneider Electric All Rights Reserved
04/03
Model Number Index
Model Number Index
SDM10BW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 SDM10CW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 SDM10SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 SDM11VM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 SDM11VMB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 SDM11VMH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 SDM12WS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 SDM13VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 SDM14VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 SDM16A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 SDM16VAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 SDM18BW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 SDM18VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 SDM1A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 SDM1DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 SDM1IMB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 SDM1VC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 SDM1VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 SDM1VIR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 SDM1VWP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 SDM21VT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 SDM21VTST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 SDM24VD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 SDM2503. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 SDM2506. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 SDM26P14V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 SDM2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 SDM2DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 SDM2IMB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 SDM2VC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 SDM2VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 SDM2VIR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 SDM350079. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 SDM350082. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 SDM350086. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 SDM350087. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 SDM36BW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 SDM38VBIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 SDM38VHIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 SDM412PJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 SDM41VT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 SDM41VTST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 SDM46P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 SDM46P14V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 SDM48PX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 SDM4AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 SDM532172. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 SDM5DE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29–30 SDM600LPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
04/03
© 2001–2003 Schneider Electric All Rights Reserved
79
Section 17–Model Number Index
Model Numbers
Model Number Index
Section 17–Model Number Index
SDM6A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SDM81VC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SDM8AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SDM8D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SDM8DB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
© 2001–2003 Schneider Electric All Rights Reserved
04/03
65 37 21 28 28
81 04/03
© 2001–2003 Schneider Electric All Rights Reserved
82 © 2001–2003 Schneider Electric All Rights Reserved
04/03
Frequency Spectrum Band
Broadcast Chnl Off-Air
Chnl
Cable Television Std Hrc
1
VHF low
Midband
Superband
Hyperband
Band
Broadcast Chnl Off-Air
Chnl
Cable Television Std Hrc
Irc
72.0036
73.2625
14
471.2500
65
469.2500
468.0234
469.2625
2
55.2500
2
55.2500
54.0027
55.2625
15
477.2500
66
475.2500
474.0237
475.2625
3
61.2500
3
61.2500
60.0030
61.2625
16
483.2500
67
481.2500
480.0240
481.2625
4
67.2500
4
67.2500
66.0033
67.2625
17
489.2500
68
487.2500
486.0243
487.2625
5
77.2500
5
77.2500
78.0039
77.2625
18
495.2500
69
493.2500
492.0246
493.2625
6
83.2500
6
83.2500
84.0042
83.2625
19
501.2500
70
499.2500
498.0249
499.2625
20
507.2500
71
505.2500
504.0252
505.2625
88.1000
FM radio
VHF high
Irc
107.9000
See low-midband channels 95-99
21
513.2500
72
511.2500
510.0255
511.2625
7
175.2500
7
175.2500
174.0087
175.2625
22
519.2500
73
517.2500
516.0258
517.2625
8
181.2500
8
181.2500
180.0090
181.2625
23
525.2500
74
523.2500
522.0261
523.2625
9
187.2500
9
187.2500
186.0093
187.2625
24
531.2500
75
529.2500
528.0264
529.2625
10
193.2500
10
193.2500
192.0096
193.2625
25
537.2500
76
535.2500
534.0267
535.2625
11
199.2500
11
199.2500
198.0099
199.2625
26
543.2500
77
541.2500
540.0270
541.2625
12
205.2500
12
205.2500
204.0102
205.2625
27
549.2500
78
547.2500
546.0273
547.2625
13
211.2500
13
211.2500
210.0105
211.2625
28
555.2500
79
553.2500
552.0276
553.2625
14
121.2625
120.0060
121.2625
29
561.2500
80
559.2500
558.0279
559.2625
15
127.2625
126.0063
127.2625
30
567.2500
81
565.2500
564.0282
565.2625
16
133.2625
132.0066
133.2625
31
573.2500
82
571.2500
570.0285
571.2625
17
139.2500
138.0069
139.2625
32
579.2500
83
577.2500
576.0288
577.2625
18
145.2500
144.0072
145.2625
33
585.2500
84
583.2500
582.0291
583.2625
19
151.2500
150.0075
151.2625
34
591.2500
85
589.2500
588.0294
589.2625
20
157.2500
156.0078
157.2625
35
597.2500
86
595.2500
594.0297
595.2625
21
163.2500
162.0081
163.2625
36
603.2500
87
601.2500
600.0300
601.2625
22
169.2500
168.0084
169.2625
37
609.2500
88
607.2500
606.0303
607.2625
23
217.2500
216.0108
217.2625
38
615.2500
89
613.2500
612.0306
613.2625
24
223.2500
222.0111
223.2625
39
621.2500
90
619.2500
618.0309
619.2625
25
229.2625
228.0114
229.2625
40
627.2500
91
625.2500
624.0312
625.2625
26
235.2625
234.0117
235.2625
41
633.2500
92
631.2500
630.0315
631.2625
27
241.2625
240.0120
241.2625
42
639.2500
93
637.2500
636.0318
637.2625
28
247.2625
246.0123
247.2625
43
645.2500
94
643.2500
642.0321
643.2625
29
253.2625
252.0126
253.2625
95
91.2500
90.0045
91.2625
30
259.2625
258.0129
259.2625
96
97.2500
96.0048
97.2625
31
265.2625
264.0132
265.2625
97
103.2500
102.0051
103.2625
32
271.2625
270.0135
271.2625
98
109.2750
108.2500
109.2750
33
277.2625
276.0138
277.2625
99
115.2750
114.2500
115.2750
34
283.2625
282.0141
283.2625
44
651.2500
100
649.2500
648.0324
649.2625
35
289.2625
288.0144
289.2625
45
657.2500
101
655.2500
654.0327
655.2625
36
295.2625
294.0147
295.2625
46
663.2500
102
661.2500
660.0330
661.2625
37
301.2625
300.0150
301.2625
47
669.2500
103
667.2500
666.0333
667.2625
38
307.2625
306.0153
307.2625
48
675.2500
104
673.2500
672.0336
673.2625
39
313.2625
312.0156
313.2625
49
681.2500
105
679.2500
678.0339
679.2625
40
319.2625
318.0159
319.2625
50
687.2500
106
685.2500
684.0342
685.2625
41
325.2625
324.0162
325.2625
51
693.2500
107
691.2500
690.0345
691.2625
42
331.2625
330.0165
331.2625
52
699.2500
108
697.2500
696.0348
697.2625
43
337.2625
336.0168
337.2625
53
705.2500
109
703.2500
702.0351
703.2625
44
343.2625
342.0171
343.2625
54
711.2500
110
709.2500
708.0354
709.2625
45
349.2625
348.0174
349.2625
55
717.2500
111
715.2500
714.0357
715.2625
46
355.2625
354.0177
355.2625
56
723.2500
112
721.2500
720.0360
721.2625
47
361.2625
360.0180
361.2625
57
729.2500
113
727.2500
726.0363
727.2625
48
367.2625
366.0183
367.2625
58
735.2500
114
733.2500
732.0366
733.2625
49
373.2625
372.0186
373.2625
59
741.2500
115
739.2500
738.0369
739.2625
50
379.2625
378.0189
379.2625
60
747.2500
116
745.2500
744.0372
745.2625
51
385.2625
384.0192
385.2625
61
753.2500
117
751.2500
750.0375
751.2625
52
391.2625
390.0195
391.2625
62
759.2500
118
757.2500
756.0378
757.2625
53
397.2625
396.0198
397.2625
63
765.2500
119
763.2500
762.0381
763.2625
54
403.2500
402.0201
403.2625
64
771.2500
120
769.2500
768.0384
769.2625
55
409.2500
408.0204
409.2625
65
777.2500
121
775.2500
774.0387
775.2625
56
415.2500
414.0207
415.2625
66
783.2500
122
781.2500
780.0390
781.2625
57
421.2500
420.0210
421.2625
67
789.2500
123
787.2500
786.0393
787.2625
58
427.2500
426.0213
427.2625
68
795.2500
124
793.2500
792.0396
793.2625
59
433.2500
432.0216
433.2625
69
801.2500
125
799.2500
798.0399
799.2625
60
439.2500
438.0219
439.2625
126
805.2500
804.0402
805.2625
61
445.2500
444.0222
445.2625
127
811.2500
810.0405
811.2625
62
451.2500
450.0225
451.2625
128
817.2500
816.0408
817.2625
63
457.2500
456.0228
457.2625
129
823.2500
822.0411
823.2625
64
463.2500
462.0231
463.2625
130
829.2500
828.0414
829.2625
131
835.2500
834.0417
835.2625
132
841.2500
840.0420
841.2625
133
847.2500
846.0423
847.2625
134
853.2500
852.0426
853.2625
135
859.2500
858.0429
859.2625
136
865.2500
864.0432
865.2625
137
871.2500
870.0435
871.2625
138
877.2500
876.0438
877.2625
139
883.2500
882.0441
883.2625
140
889.2500
888.0444
889.2625
UHF and Ultraband
Low-Midband
UHF and Ultraband continued
Ultraband continued
Square D Company 1601 Mercer Road Lexington, KY 40511 1-888-SquareD (1-888-778-2733) www.SquareD.com
Catalog No. 1400CT0101R3/03 April 2003 © 2001–2003 Schneider Electric All Rights Reserved Replaces 1400CT0101R3/02 dated 04/02.
