Transcript
SPORTY BLUETOOTH HEADPHONE music & call
Muses 1 INSTRUCTION
Start here Following items are included
Ear hoops
Ear caps
USB cable
Product overview 1. Ear cap 1
2. Multifunction button
2
3. Charge jack 4. Ear Hoop
3 4
6
5. Status indicator 6. Noise reduction mic
5 7
7. Track Back Volume -
8
8. Track forward Volume + 9
9. Talking mic 10. Line
10
Basic operation Volume control Press the "+" or "-" button to turn volume up or down, you hear beep once reach the maximum or minimum volume.
Status indicator Instruction
LED status
Voice prompts
Power on
Blink blue three times
Power on
Power off
Blink red three times
Power off
Standby
Blink blue once every 5 seconds
/
Pairing
Red and Blue alternately
Pairing
Incoming call
Blink blue continuous
/
Charging
Stay on red while charging, Stay on blue after fully charged
/
Pairing Pair one phone 1. Press and hold the Multifunction Button until LED flashes blue and red alternately, you hear "Power on" and "Pairing", now headphone is in pairing mode. 2. Activate Bluetooth on your phone and set it to search for new devices.
Bluetooth
ON
Scan
3. Select "Muse1". If your phone asks, enter 0000 (four zeros) for the passcode or accept the connection. The LED indicator stops flashing red and blue once successfully paired, you hear "Connection successful". Some phone list an option to "Play through headphone", select to use the headphones.
Bluetooth
ON
Muses1
Connect
Pair another phone Multipoint technology enables you to pair another phone and take a call from either. To pair with another mobile phone, follow the steps for "Pair one phone". After pairing successfully, restart the headphone to connect to 2 paired mobile phone automatically.
Bluetooth
ON
Muses1
Bluetooth
ON
Muses1
Connect Connect
Call Answer a call Press volume button (+ or -) to answer an incoming call. End a call Press and hold the volume button (+ or -) for about 2 seconds to end a call. Redial last call Double-press the volume button "-", the mobile phone will redial the last call number. Automatic switch between music and calls When a call rings during a music playing, the music automatically pauses to allow you to answer or ignore the call. Once the call is ignored or ends, the music is resumed.
Music (Need music player supports.)
Trackback Press and hold "▲" for about 2 seconds when playing music, and the previous song will be played. Trackforward Press and hold "▼" for about 2 seconds when playing music, and the next song will be played. Pause/Play Press "-" and "+" button simultaneously once to play / pause music. (Some phones may require you to start a media player first)
More features Battery Indicator When the headphone is connected to a device with iOS system, a battery indicator will appear at the upper right of the system, indicating battery status of the headphone.
Auto power-off When the distance between the headphone and the mobile phone is beyond effective range, a voice prompt "Connection lost" and headphone disconnects with the mobile phone, the headphone will power off automatically once no active for 10 minutes.
Effective range
30min
muses1
?
10min
?
Automatic connection after powering on When the headphone and phone have been paired once, they will automatically connect when the headphone is on and Bluetooth is activated on the phone.
Power off To power off the headphone, press and hold the multifunction button for about 4 seconds, the LED blink red three times, you hear "Power off", then power off the headphone.
Charging Your headphone has enough power to complete the pairing and a few calls. When battery is low, you will hear the voice prompt "Battery low". It takes 1.5 hours to fully charge the headphone. The red LED turns on during charging. The red LED will turn off and the blue LED will turn on after being fully charged. Note: The lifetime of the battery will be significantly reduced if your headphone is left uncharged for a long period. We recommend that you recharge your headphone at least once a month.
Connection standby After successful pairing and connection, you will hear the voice prompt "Connection successful". the headphone will be in turning on mode or standby mode automatically and the blue LED will flash once every 5 seconds, when the headphone dis connect the phone, you will hear the voice prompt "Connection lost".
Hard reset In turning on mode, press and hold the multifunction button with the charger plugged to reset the headphone. Then the red LED will light (you can release the multifunction button 2 seconds after mounting the charger).
