Transcript
MWS
D ES C R IPTION
MWS, Modular Wiring Systems, provide low cost installation of branch circuit wiring for lighting and power. Using modular components that plug together, MWS can be installed in a fraction of the time of hardwiring. Plus, MWS offers the advantage of relocating fixtures and outlets in future renovations.
®
Type
Catalog # Project
Date
Comments
The MWS Drop Cable (DC) supplies power to out of system units that are wall mounted or ceiling mounted.
Prepared by
MWS Drop cables may be plugged into the last fixture cable (FC) or from a Splitter (SP) anywhere within the system. DES IGN FEA TUR ES
• UL Listed under Standard 183 for make or break under load.
• Copper conductors are THHN insulated wire rated 90°C.
• Meets requirements of Article 604 of the National Electrical Code.
• Galvanized steel exterior with integral keying for voltage and amperage.
• MWS components assembled with 12 AWG/10 AWG conductors rated at 20 amperes with full size ground wire.
• Cable end supplied with 1/2" connector with locknut and 6" prestripped leads. • DC cable allows you to easily supply power to other system units such as j-boxes, receptacles or fixtures.
• Valox 365 constructed contact housings are approved for environmental air plenums.
DC DIMENS IONA L D A TA
DROP CABLE
SYSTEM VIEW (not to scale)
5/8" [16mm]
Side
Drop Cable
Extender Cable
1-7/8" [47mm]
Splitter or Circuit T
Modular Wiring System
Junction Box or any Out of System Unit supplied by others. Extender Cable
Drop Cable (DC) Supplies power to out of system units. (Fixtures, J-boxes, etc.). 4-3/8" [112mm]
Top
Typical MWS Wiring System Application shown utilizing Drop Cable (DC). Consult MWS Installation, Application and Specification Manual for additional comprehensive system information.
OR D ER ING INFOR M AT I O N S A M P L E N U M B E R : 2 7 D C 1 2 /2 G 1 1
MWS AUTOCAD DRAFTING MWS offers AutoCAD drafting to layout MWS, providing the contractor with additional benefits.
DC Component DC=DropCable
Conductors and Size 10/2G=#10, 2 Conductors Plus Ground 10/3G=#10, 3 Conductors Plus Ground 10/4G=#10, 4 Conductors Plus Ground 12/2G=#12, 2 Conductors Plus Ground 12/3G=#12, 3 Conductors Plus Ground 12/4G=#12, 4 Conductors Plus Ground
Cable Length (Feet) 05=5' 09=9' 11=11' 15=15'
Options 2N=2 Neutral (1)
MWS design layout time is reduced. Bills of material are computer-generated guaranteeing accuracy. MWS drawing symbols and details standardized. Layouts are available on CD or e-mail. To utilize this service and for additional information, contact the MWS Sales Department (888) 487-4887.
NOTES: (1)12/4G and 10/4G only. Specifications & dimensions subject to change without notice. Consult your Cooper Lighting Representative for availability and ordering information.
SH IP P ING D A T A
Install dust covers on unused open ends. Scale is exaggerated on fixtures and MWS system applications.
Specifications and dimensions subject to change without notice.
YS
ER
TEM S
Eaton’s Cooper Lighting Business 1121 Highway 74 South Peachtree City, GA 30269 P: 770-486-4800 www.cooperlighting.com
All electrical boxes, conduit, connections and switches by others.
C
Eaton 1000 Eaton Boulevard Cleveland, OH 44122 United States Eaton.com
Unit Standard Wt. Qty./Carton 2.0 lbs. 12 3.0 lbs. 9 3.5 lbs. 8
S
Cable Length 5' 9' 11'
D
Voltage 12=120V 20=208V 24=240V 27=277V 34=347V 48=480V
TIFIE
ADF031851 2015-01-15 09:36:13
