Transcript
Quick Start Guide TeleEye MX121E-HD Network Camera This Quick Start Guide will guide you how to install and configure the TeleEye MX121E-HD Network Camera for remote video monitoring.
1. Camera Installation Step 1
After mounting the camera on the wall or ceiling, connect the Ethernet cable to the LAN adapter. If PoE is not available, connect the 12VDC power supply to the power cable.
[Reference] Please refer to the section 2 for connecting the cable to RJ45 plug. Power Cable (12V DC)
Ethernet Cable
Network Switch / Router
12V DC Power Adapter (Optional)
Relay
Alarm Cable Audio In
Step 2
Audio Out
Internet
Start sureSIGHT or a web browser to start a remote video monitoring in order to adjust the camera.
[Reference] Please refer to the following sections to understand how to start video monitoring.
Step 3
After removing the camera cover, loosen the screws to adjust the viewing angle of the camera.
Adjust the viewing angle Loosen the screws
Step 4
Tighten the screws to fix the direction of the camera module. Close the camera cover. 1
2. RJ45 Wiring Step 1
Make sure whether Type A or Type B wiring scheme is used for the Ethernet cable (Type B is more common).
Step 2
The two colour codes indicated on the plug represent the wiring scheme for Type A and Type B cables. Type A Wiring Scheme Type B Wiring Scheme
Step 3
Open the tab of the plug
Step 4
According to the wiring scheme of the cable, follow the corresponding colour code on the plug to arrange the 8 wires. Close the tab after inserting the 8 wires into the wire holders.
Insert the 8 wires
Close the tab
3. Audio and Relay Installation Step 1
Loosen the 6 screws to open the up-cover.
6 Screws
2
Step 2
Connect the corresponding wire to the terminal block plug. Audio Input Audio Input Ground Audio Output Audio Output Ground Relay Terminal 1 Relay Terminal 2
Step 3
Plug in terminal block plug to terminal block. Terminal Block
Plug In
4. Micro SD Card Installation Step 1
Loosen the 6 screws to open the up-cover.
[Reference] Please refer to section 3 step 1 for opening the up-cover.
Step 2
Ensure the arrow sign on the Micro SD card upwards. Top
Bottom Arrow Sign
3
Step 3
Insert the Micro SD card to the Micro SD slot and push until “Click” sound.
Micro SD Slot
5. Default User Name and Password Default user name is “admin” while default password is “0” + “digits of serial number”. Here is an example:
Serial Number : MXC10210 User Name : admin Password : 010210
6. IP Setup Utility Step 1
After installing sureSIGHT and turning on the network camera, select “Run TeleEye IP Setup Utility” from the windows start menu.
Step 2
Search the target camera by its serial number, highlight the corresponding row from the list to select it. If the camera cannot be found, click the [Refresh] button.
Step 3
Press [Edit] button to change the network settings of the camera, including IP, ports, mask, etc.
Step 4
Enter user name and password to save the information when prompted.
[Reference] Please refer to section 5 for the default user name and password.
7. Live Monitoring with Web-Browser Step 1
Type the IP address of the network camera in a web browser. 4
Step 2
Input the user name and password.
[Reference] Please refer to section 5 for the default user name and password.
Step 3
Click the [Connect] button to connect the selected video stream. Video will then be displayed on the browser as follow.
8. Live Monitoring with sureSIGHT Step 1
After installing sureSIGHT and turning on the network camera, select “Run sureSIGHT Lite” from the windows start menu. Input the user name and password to log-in to the sureSIGHT. [Reference] Please refer to section 5 for the default user name and password.
Step 2
Click the [
] button on the top of the sureSIGHT.
5
Step 3
Search the target camera by its serial name and click its corresponding box on the left. you may choose more than one camera. Click [Next] after selection.
Step 4 Input the user name and the password. Then, click [Next].
[Reference] Please refer to section 5 for the default user name and password.
Step 5 You may click [Details] to change the site name and IP/sureLINK. After setting, click [Finish].
Step 6 The video will be displayed on sureSIGHT by double clicking the site on the left panel.
[Reference] For detail operations, please refer to sureSIGHT user manual. 6
