Transcript
Ness TCD
High Security Alarm Monitoring The Securitel Alternative! Multipath IP & GPRS
The Ness TCD provides a high security multipath monitoring system compatible with all Ness dialler control panels including M1/D8x/D16x/D24 & R16 and other panels capable of Contact ID.
■ Compatible with all Ness control panels ■ High security dual pathway signalling internet and GPRS ■ Works with any broadband service provider and the Optus mobile network ■ Requires NO dedicated PSTN line ■ NO call or connection charges ■ Meets all Australian and NZ standards ■ Minimal installation - simply plug in any Ness dialler
Compatible with
■ Easy commissioning - all details are handled by your central station
Client’s Premises
Ness Alarm panel
TCD Comms Interface
Internet
GPRS Network
Emizon Service
Emizon Service Platform
Central Station
IP Network Controllers
Operator Workstations
TCP/IP protocols Contact ID protocols Ethernet with AES encrypted protocol Ademco 685 protocol
Part No. 106-099 Ness TCD includes:
• TCD Module • Ness housing • 12v 7Ah backup battery • Power Supply • Telephone lead
Installer’s Q & A Secure Signalling with Global 21 and The Q. MCM TCD Q. What data services are required at the premises? How do I configure the router at the premises? A. ADSL broadband from any ISP and Optus mobile A. TCD only requires outbound TCP/IP ports 18000 coverage for dual path monitoring. Or just Optus to 18049 to be opened. TCD does not require any mobile coverage if opting for GPRS only service. inbound ports to be opened. PSTN Dial Capture RS232/RS485 Data ports for ease of installation and migration for serial interface to panel Q. Which central stationsservices are compatible? secure Q. Howand from analogue and for remote maintenance UDL is the TCD from takeovers by other installers or central stations? A. A number of central stations around Australia,
LED Status Display
including Ness Monitoring can monitor the TCD. Ask your central station if they subscribe to the Emizon network.
A. Similar to Securitel,for the TCD is locked to your central step-by-step installation station and cannot be decommissioned and diagnostics without authorisation. ie signal strength and IP connection path status Q. What is the ongoing cost for the service?
Q. How do I interface the TCD to my alarm panel? A. Install the TCD housing close to your alarm panel. Plug your dialler’s phone lead into the TCD’s phone socket. Connect a LAN patch cable to the TCD from the premises switch/router. Power up and commission as below and that’s it.
A. There are no separate or hidden costs. The client pays only monitoring fees at a rate comparable to Securitel. SIM CARD
ready for ‘fit and go’ installation Q. Can I still upload/download my control panel via the telephone line?
Q. How do I commission the TCD?
A. No. Your panel’sStandard dialler is now plugged into the TCD Antenna unit and not a PSTN phone line. Ness D8x and D16xConnection can be programmed using for easy migration NessComms software via direct connect cable to the from analogue services panel’s serial port while connected to the TCD. Ness ECO8x, R16 & D24 panels cannot be upload/ downloaded while connected to the TCD. Ness M1 retains full upload/download capabilities via the M1 Ethernet Module and LAN/WAN. A Ness M1 with an Ethernet Module also has full user control via M1 User Control software or an Ethernet Connector iPhone using a third party app. for wired connection to broadband/IP networks
A. Advise the central station of the TCD serial number. Power up TCD from 12 volts supply. Wait for “BC” (Boot Complete) to appear on the TCD display. Ask the central station to activate the TCD. Primary path & Secondary path LEDs turn ON. The central station sets up TCD to communicate to your panel in Contact ID and you are ready to send events.
‘One-Touch’ Set and Mode Programming Buttons
- to access to the latest software
Six simple steps to secure signalling STEP 1
Fit the TCD in the panel
Connect GSM antenna, Serial Tx and Rx (or telecom lead for Contact ID capture) and the12 Volts DC power. Connect the network cable from the TCD Ethernet port to the broadband router.
STEP 2
Boot up
Power-up the TCD. The GPRS and Ethernet activity LEDs will indicate that the signalling paths are available. The TCD is now ready for commissioning to the Monitoring Centre.
STEP 3
Software update
Check for updates by pressing the Mode and Set buttons together for 10 seconds.
STEP 4
Call Monitoring Centre
STEP 5
Commission
STEP 6
Test
Contact your Monitoring Centre with the TCD serial number. The Monitoring Centre will then match this with the customer order details and activate the service. After activation by the Monitoring Centre, press the Set button for 5 seconds.
The service is now ready for testing.
MCM Electronics Pty Ltd Unit 3/10 Abel Street, Penrith, NSW 2750, Australia SYDNEY 02 8825 9222
[email protected]
MELBOURNE 03 9875 6400
[email protected]
BRISBANE 07 3399 4910
[email protected]
PERTH 08 9328 2511
[email protected]
ADELAIDE 08 8152 0000
[email protected]
NFS (NZ) 09 580 1576
[email protected]
Tel: (02) 4721 8067
Fax: (02) 4721 8572 Web: www.mcmelectronics.com.au www.ness.com.au Email:
[email protected]
© 2009 Ness Security Products Pty Ltd ABN 28 069 984 372 Photographs are used for illustrative purposes only. Design and specifications may vary.
Copyright © Emizon Pty Ltd
2
IL-AU-GEN JULY 2008
