Transcript
NET-ACCESS Cabinet for Cisco Nexus 7018 Switch INSTRUCTIONS CM385E © Panduit Corp. 2009, 2010
TOOL LIST #2 Phillips Screwdriver #3 Phillips Screwdriver Needle Nose Pliers 1/8” Allen Key 1/2” Socket Wrench 3/8” Socket Wrench 5/16” Socket Wrench 7/16” Socket Wrench 3/8” Wrench
Component Guide
CN7018-EXT CN7018-EXTND* CN3 (1) Base Cabinet (2) Cable Management Finger Kits (1) Hardware Kit (2) #12-24 Threaded Equipment Rail Sets
(2) Top Side Extensions (2) Top Front/Rear Extensions (2) Bottom Door Shoe Extensions (2) Bottom Side Extensions (2) Split Door Sets (2) Vertical Side Supports (4) Lower Horizontal Supports (1) Hardware Kit
CNAE7018 (1) Inlet Duct Assembly (1) Exhaust Duct Assembly (1) Bottom Duct Assembly (1) Inlet Duct Seal Bracket (5) Mounting Brackets (1) Hardware Kit
*CN7018-EXTND does not contain doors
CNPS7018* (2) Side Panels (1) Hardware Kit
*(1) CNPS7018 kit is needed per cabinet side
For installation instructions for the CN3 cabinet, please reference instruction sheet CM317C. FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp Page 1 of 12
INSTRUCTIONS CM385E
CN3 Cabinet Preperation Remove J-Hooks Remove all (4) J-Hooks from CN3 cabinet by removing (2) #12-24 screws per J-Hook as shown.
Remove Door Shoe Bumpers and Bushing Remove (3) door shoe bumpers and (1) door rod bushing from each door shoe on the CN3 cabinet as shown. Door Rod Bushing
J-Hook #12-24 Screws
Bumpers
Reposition Equipment Rails All four rails are fully adjustable. To change depth, loosen three (3) 5/16 x 3/4” mounting bolts per cabinet rail using a 1/2” socket wrench and slide rails flush with cabinet posts. Retighten the mounting bolts to 14ft.-lbs. Proper torque ensures equipment rails are bonded to the cabinet frame.
5/16” Mounting Bolt (use 1/2” socket wrench)
5/16” Mounting Bolt (use 1/2” socket wrench)
Adjusted Rails
For Technical Support: www.panduit.com/resources/install_maintain.asp Page 2 of 12
INSTRUCTIONS CM385E
Requirements for Switch Installation CISCO NEXUS 7018 SWITCH CRADLE MUST BE mounted so that the shaded area shown below is kept clear to allow for proper fit of all switch ducting to cabinet. See view below for Panduit-suggested cradle position (refer to Cisco for cradle installation instructions). NOTE: If casters are installed on NET-ACCESS cabinet, SWITCH CRADLE MUST BE installed so that the bottom six (6) rack spaces are kept clear to allow for proper fit of all switch ducting to cabinet, and that cabinet casters do not interfere with switch ducting (11.25” above bottom edge of equipment rail).
THIS AREA MUST BE KEPT CLEAR TO ALLOW FOR SWITCH DUCTING INSTALLATION
See Detail View
Install switch cradle (Cisco p/n: N7KC7018-BSK=) so that slots of cradle align with tapped holes of equipment rails at 5th - 7th rack spaces (Bottom of switch cradle mounting flange will be positioned 7.75” above bottom edge of equipment rail).
7.75”
Detail View
For Technical Support: www.panduit.com/resources/install_maintain.asp Page 3 of 12
INSTRUCTIONS CM385E
Exhaust Duct Installation NOTE: DO NOT break yellow banding on ducting cartons until ducting is ready for installation. Install (2) universal ducting brackets on the top and bottom surfaces of the exhaust duct using (6) #10-32 pan head Phillips screws and (6) #10 lockwashers. Mount duct assembly to cabinet posts using (7) # 12-24 serrated hex head screws through ducting brackets and slotted flange as shown. The top flange of duct assembly should be positioned above the top surface of switch.
#10-32 Pan Head Phillips Screws
See Detail View
#10 Lockwashers
Duct Assembly Top Flange
Universal Ducting Bracket
Assembled
Exhaust Duct
Position Duct Assembly Top Flange Above Top Surface of Switch [7] #12-24 Serrated Hex Head Screws
FRONT OF SWITCH
(use 5/16” socket wrench)
For Technical Support: www.panduit.com/resources/install_maintain.asp Page 4 of 12
INSTRUCTIONS CM385E
Intake Duct Installation Assemble lower intake duct to upper intake duct using (3) #10-32 hex nuts with integrated lockwashers and (2) #10 washers (placed inside the ducting). Adjust intake duct to fit suggested installation location as shown below. Install (2) universal ducting brackets on the top and bottom surfaces of the intake duct using (6) #10-32 Phillips screws and (6) #10 lockwashers. Mount intake duct assembly to cabinet posts using (4) #12-24 serrated hex head screws through ducting brackets as shown. Install (1) #12-24 serrated hex head screw at back of intake ducting, securing intake ducting to cabinet equipment rail (see detail view). Ensure that lower intake duct rests on bottom cabinet beam. Upper Intake Duct 54.25” INSTALL TOP DUCT MOUNTING BRACKET AT 16th SET OF PAIRED HOLES FROM TOP OF CABINET POST
Lower Intake Duct (secure to upper intake duct wit [3] #10-32 hex nut and [2] #10 washer)
Universal Ducting Bracket
#10-32 Pan Head Phillips Screws and #10 Lockwashers
3.5” INSTALL BOTTOM DUCT MOUNTING BRACKET AT 1st SET OF PAIRED HOLES FROM BOTTOM OF CABINET POST
[1] #12-24 Serrated Hex Head Screw (use 5/16” socket wrench)
[4] #12-24 Serrated Hex Head Screws
REAR OF CABINET
(use 5/16” socket wrench)
For Technical Support: www.panduit.com/resources/install_maintain.asp Page 5 of 12
FRONT OF CABINET
INSTRUCTIONS CM385E
Intake Duct and Bottom Duct Installation Attach flap seal to bottom duct as shown below. Mount bottom duct to equipment rails using (4) #12-24 serrated hex head screws as shown. Attach rear mounting bracket to bottom duct using (2) #10-32 hex nuts with integrated lockwashers (there are (2) pre-installed press studs on the rear of the bottom duct). Adjust rear mounting bracket so that it rests against bottom of 7018 switch. Secure the bracket to rear equipment rails using (2) #12-24 serrated hex head screws as shown. Attach flap seal to intake duct seal bracket as shown. Mount intake duct seal bracket with flap seal to upper universal ducting bracket with (2) #10-32 hex nuts with integrated lock washers. Positioning of intake duct seal bracket is adjustable to allow for tight seal of intake duct to 7018 switch. Secure intake duct transition bracket to bottom duct and intake duct with (4) #10-32 hex nuts with integrated lockwashers as shown below.
[2] #10-32 Hex Nuts (use 3/8” socket wrench)
Intake Duct Seal Bracket Flap Seal
Flap Seal
Bottom Duct
FRONT OF CABINET
#12-24 Serrated Hex Head Screws (use 5/16” socket wrench)
Rear Mounting Bracket
Intake Duct Transition Bracket Intake Duct [2] #12-24 Serrated Hex Head Screws (use 5/16” socket wrench)
[2] #10-32 Hex Nuts REAR OF CABINET
(use 3/8” socket wrench)
[4] #10-32 Hex Nuts (use 3/8” socket wrench)
For Technical Support: www.panduit.com/resources/install_maintain.asp Page 6 of 12
INSTRUCTIONS CM385E
Top Cap Extension Assembly Installation of Top Side Extensions Remove (4) side knock-outs from original top cap. Install (2) top side extensions, using (2) 5/16” serrated flange lock nuts on each extension (there are pre-installed 5/16” press-studs in side extensions). Do not tighten side extensions until front and rear extensions are mounted and aligned with original top cap. Top front and back extension installation is shown at the bottom of this page.
Side Extensions
Assembled
Remove Knock-outs 4 places
5/16” Serrated Flange Lock Nut (use 1/2” socket wrench)
Installation of Top Front and Back Extensions Remove the front and rear center key hole knock-out features from the original top cap. Attach (2) top front and rear extensions, using (4) #1032 nuts, (4) #10 lockwashers, (1) 1/4-20 carriage bolt, and (1) 1/4-20 serrated hex nut per extension piece (there are (4) pre-installed #10 press-studs in each extension). Align all top extension parts, leaving a minimal gap between side and front/rear parts. Ensure that all extension components are flush with top cap. Secure side extensions by tightening (4) 5/16” serrated flange lock nuts.
Assembled Ensure that these surfaces are flush with top cap
Rear Extension
Front Extension
Remove Center Key Hole Knock-outs 1/4-20 Carriage Bolt See Detail View See Detail View
#10 Lockwasher
1/4-20 Serrated Hex Nut (use 7/16” socket wrench) #10-32 Nut (use 3/8” socket wrench)
For Technical Support: www.panduit.com/resources/install_maintain.asp Page 7 of 12
INSTRUCTIONS CM385E
Door Shoe Extension Assembly Installation of Front and Back Bottom Door Shoe Extensions NOTE: Leveling legs to be installed ONLY if the base cabinet is raised off the ground on its leveling legs. Install (2) leveling legs in each door shoe extension by threading through bottom of door shoe extender. Adjust leveling legs with 3/8” socket wrench. Install (2) door shoe extensions to existing cabinet door shoes using (6) #12-24 pan head Phillips screws on each side and (6) #12 lockwashers; (4) screws vertical on front and (2) screws horizontal from behind. Install centering screw first (NOT TIGHT). Install (2) horizontal screws through rear of door shoe extender as shown. Install and tighten (3) vertical screws and tighten centering screw. #12-24 Pan Head Phillips Screws and #12 Lockwashers
Leveling Legs
Centering Screw
Door Shoe Extension
Centering Hole #12-24 Pan Head Phillips Screw and #12 Lockwasher
Existing Cabinet Door Shoe
Installation of Bottom Side Extensions Install (2) bottom side extensions as shown. Secure using (2) #12-24 serrated hex head screws on each extension.
Assembled
Bottom Side Extension
#12-24 Serrated Hex Head Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp Page 8 of 12
INSTRUCTIONS CM385E
Vertical Side Support Installation Mount (2) vertical side supports using (4) #10-32 nuts and (4) #10 lockwashers per post; (2) at top and (2) at bottom (there are (4) pre-installed press studs in each post).
Assembled
These surfaces must be flush with original top cap
NOTE: In order to install the vertical side supports, the top extenders must be flush with the top cap surface as described on page 6 of 10.
Vertical Side Supports
#10-32 Nuts and #10 Lockwashers (use 3/8” socket wrench) Vertical Side Supports
Installation of Lower Horizontal Supports Mount (4) lower horizontal supports, using (2) #10-32 flat head screws and (2) #10 lockwashers (at bottom side extension) and (1) 1/4-20 hex head screw (at door shoe extension) per lower horizontal support as shown. Assembled Lower Horizontal Supports
Lower Horizontal Supports
See Detail View
#10-32 Flat Head Screws and #10 Lockwashers (use 1/8” Allen Key)
#10-32 Flat Head Screws and #10 Lockwashers (use 1/8” Allen Key) 1/4-20 Hex Head Screw (use 7/16” socket wrench)
For Technical Support: www.panduit.com/resources/install_maintain.asp Page 9 of 12
INSTRUCTIONS CM385E
Split Door and Side Panel Installation Split Door Installation
Side Panel Spring Clip Installation
Lift split door and align fixed hinge pin with the bushing in the bottom door shoe extension. Swing door up and pull down the lever of the spring loaded hinge pin and align pin with the bushing in top cap extension. Release lever when aligned. Verify spring loaded hinge pin is fully engaged into bushing before proceeding. Reverse steps to remove door.
Spring Loaded Hinge Pin
Install four (4) spring clips per side of cabinet by first removing paint masking from area as shown. Slide spring clip in place until it clips into pilot hole. The spring clips bond the side panel to the cabinet frame.
Remove masking from this area
Fixed Hinge Pin
Install spring clip
Spring Clip Locations
Adjustment of Side Panel
Side Panel Installation Pull down the lever of the top spring loaded hinge pin and lock into position. Lift side panel and align bottom pin with the hinge point in the lower horizontal support. Swing door up and align pin with the hinge point in top cap extension. Release locked hinge pin lever. Pull and lock remaining spring loaded hinge pins and move side panel into position. Release levers when aligned. Reverse steps to remove side panels.
Adjust side panels by loosening the (2) hex head screws securing the bottom side extension to the cabinet frame and the (1) hex head screw securing the extension to the door shoe extender as shown. Reposition the bottom side extension and horizontal supports as necessary. Tighten the (3) hex head screws.
Hinge Pin Unlocked Position Top Spring Loaded Hinge Pin
Loosen these screws Hinge Pin Locked Position
Reposition Bottom Side Extension as necessary
Bottom Spring Loaded Hinge Pin
Loosen this screw
For Technical Support: www.panduit.com/resources/install_maintain.asp Page 10 of 12
Reposition Horizontal Support as necessary
INSTRUCTIONS CM385E
Ganging with Net-Access Cabinets Position Net-Access cabinet next to CN7018 cabinet. Install (2) top ganging brackets by passing through the slots in the top cap side extension and secure each with (1) #10-32 hex nut and (1) #10 lockwasher to the #10-32 press stud in the top cap side extension. Fasten top ganging brackets to Net-Access cabinet ganging tab using (1) #12-24 serrated hex head screw per each bracket. Install (2) bottom ganging brackets to CN7018 cabinet with (1) #12-24 serrated hex head screw per bracket as shown. Fasten bottom ganging bracket to the back side of Net-Access cabinet door shoe using (1) #12-24 serrated hex head screw per bracket. NOTE: Net-Access cabinet can be positioned so that it is flush with either the front or the rear of the CN7018.
Top Mounting Locations
To gang Net-Access cabinet flush with FRONT of CN7018, install top ganging brackets here
Pass top ganging bracket through slot in top cap side extension CN7018 cabinet
#10-32 hex nut and #10 lockwasher (use 3/8” wrench)
FRONT OF CN7018 CABINET
Net-Access cabinet Net-Access cabinet ganging tab
To gang Net-Access cabinet flush with REAR of CN7018, install top ganging brackets here
#12-24 serrated hex head screw (use 5/16” socket wrench)
CN7018 GANGED WITH NET-ACCESS CABINET Bottom Mounting Locations Bottom ganging bracket
Back side of existing cabinet door shoe
#12-24 serrated hex head screw (use 5/16” socket wrench) Bottom ganging bracket To gang Net-Access cabinet flush with FRONT of CN7018, install bottom ganging brackets here
#12-24 serrated hex head screw (use 5/16” socket wrench)
FRONT OF CN7018 CABINET To gang Net-Access cabinet flush with REAR of CN7018, install bottom ganging brackets here
For Technical Support: www.panduit.com/resources/install_maintain.asp Page 11 of 12
INSTRUCTIONS CM385E
Ganging of Two CN7018-EXT NOTE: Cabinets must be aligned and level prior to installation of ganging hardware. See latest revisions of CM317 and CM385. TOP CAP GANGING: Remove [2] circular knockouts on sides of top cap at front and rear ganging locations (remove knockouts prior to positioning of cabinet). With cabinet top caps touching, secure cabinet tops together with [1] 5/16” serrated bolt and [1] 5/16” serrated nut at each ganging location (use 1/2” [13mm] socket). BASE OF CABINET GANGING: With cabinet bases touching, secure cabinet bases together with [2] 1/4” x 2-1/2” bolts (use 7/16” [11mm] socket; bolts fasten into 1/4” tapped holes in cabinet base) at the front and rear of cabinet as shown below.
Remove [2] Knockouts
TOP CAP GANGING
5/16” Serrated Nut
5/16” Serrated Bolt
BASE OF CABINET GANGING (Front)
1/4” Tapped Hole BASE OF CABINET GANGING (Rear) 1/4” x 2-1/2” Bolt
For Instructions in Local Languages and Technical Support: www.panduit.com/resources/install_maintain.asp
www.panduit.com Page 12 of 12
1/4” x 2-1/2” Bolt
E-mail:
[email protected] Fax: (708)444-6448
