Network Security System

Transcript

Network Security System WJ-GXE900 WJ-GXD900 MPEG2 Encoder MPEG2 Decoder MPEG2 Encoder WJ-GXE900 MPEG2 Decoder WJ-GXD900 High-definition MPEG2 for monitoring of surveillance camera images at any location. With the new Panasonic WJ-GXE900 MPEG2 encoder and the WJ-GXD900 MPEG2 decoder, a high-quality video image monitoring system can be built by connecting camera surveillance points and the monitoring room. With conventional wide-area/large-size image surveillance systems, there exists the problem of increased deterioration of image quality the farther away the camera is located from the monitoring room. The Panasonic system compresses the camera image with a high-quality MPEG2 image encoder and transmits the data to IPs, while a decoder receives the data to be displayed on a monitor. This technology ensures that the image quality will not be affected by transmission distance, thus enabling image monitoring from anywhere with a high quality image equivalent to that of TV broadcasting. There are two types of image transmission systems the multicast system and the unicast system either of which can be selected and configured according to the type of system or application software. Major Advantages • High-definition MPEG2 • MPEG2 is an image compression technology used for DVD-video discs and digital satellite broadcasting. The technology ensures remote surveillance with high-quality video images. • Low delay of approximately 150ms • The difficulties of camera switching and PTZ control have been significantly reduced. • Camera control using a single coaxial cable • Camera functions, including panning, tilting, and zooming, can be controlled from the system controller by using CGI commands through a single coaxial cable. • Camera title display • A title can be superimposed on the camera image with up to 16 alphanumerics. • Multicast transmission • The transmission system reduces loads on the server, thus ensuring efficient utilization of the network. Broadband communications transmit camera images in high-quality video Video images from a camera connected to the encoder are digitally compressed and transmitted. A decoder receives the digital data and reproduces it on a monitor. The adoption of the MPEG2 system combined with Panasonic,s unique transmission technologies ensures video monitoring with natural and high-quality images. High-quality transmission in MPEG2 Multicast system MPEG2 image compression technology, employed in digital satellite broadcasting, is used to send and receive video images and voices at a rate of 9Mbps and 30frames/second maximum. You can monitor the status at remote locations with high-definition images. Image L2SW MPEG2 encoder WJ-GXE900 Four(4) Cameras 9Mbps max. 30frames/second max. Unicast system The multicast system is best suited to cases where the number of cameras exceeds that of monitors or where video images from one camera are monitored with multiple display monitors. The unicast system is best suited to cases where video images from specified cameras are displayed full-time on specified display monitors. Monitor L3SW MPEG2 decoder WJ-GXD900 Controls direction of rotation Low delay of approx. 150ms Operating PC Controls direction of camera rotation Simultaneous monitoring of four channels Low delay of approximately 150ms WJ-GXE900 WJ-GXE900 Panasonic,s unique technology has successfully reduced the delay time for sending data to the decoder from the encoder to as low as 150ms. The result is natural, smooth monitoring without the difficulties inherent in conventional systems when operating the camera. Conventional D C B The encoder has a 4-input design. You can connect various monitoring cameras, such as ultrasensitive cameras and dome cameras. The decoder is equipped with four video outputs and one 4-split screen video output, thus enabling monitoring of video images from four cameras. Panasonic D A C B A D D Slow image transmission Short delay C B WJ-GXE900 100BASE-TX 100BASE-TX 100BASE-TX B Camera A A 1.5Mbps Camera E Camera H Requires time for operating camera D 10BASE-T/ 100BASE-TX 10BASE-T/ 100BASE-TX 100BASE-TX/ 1000BASE-T 3Mbps A Switching hub (100Mbps/1000Mbps compatible) C A B Switching hub (100Mbps/1000Mbps compatible) C B Camera B Camera F Camera C Camera G Camera D Camera H 6Mbps Camera A WJ-GXD900 A Ensures smooth camera operation 9Mbps 100BASE-TX/ 1000BASE-T PC PC WJ-GXD900 Camera D Camera E Camera H Camera A Camera control through a single coaxial cable Panning, tilting, and zooming combinations of the camera can be controlled, without installing additional control cables, by sending CGI commands from the system controller. The system controller can be customized according to the size of the surveillance system and the operating methods. Equipment control with RS-485 cables is also possible. Surveillance camera CAMERA CONTROL page : WJ-GXE900 System controller Encoder L2SW L3SW CGI commands for camera control are sent to the encoder from the system controller. Encoder L2SW Encoder L2SW Decoder L3SW Single Screen Camera D Camera E System Examples 4-split screen Highly reliable system Existing system Up to now, the complicated cable wiring of surveillance systems for a complex facility has been one of the factors that deteriorate system reliability. Now, by installing Panasonic,s MPEG2 encoder and decoder at each surveillance point or monitoring room with dedicated fiber optics, you can arrange the cable wiring in a simpler way, thus ensuring highly secure system stability. WJ-GXD900 Flexible compatibility for further system expansion L3 switch System850 (WJ-SX850) Video images from multiple cameras can be distributed simultaneously by introducing the MPEG2 encoder and decoder, which are compatible with the multi-cast system featuring high-speed switching capability and dedicated large-capacity fiber optic cables. Now, you have the flexibility to expand surveillance points and monitoring rooms. WJ-GXD900 Network WJ-GXE900 Surveillance points identifiable with characters A variable transmission rate is available anytime The video transmission rate can be dynamically varied during an alert or through the CGI control from the system controller without rebooting the system. A title of up to 16 characters can be given to each camera on the network. You can identify camera locations with Alphanumeric characters, thus enabling reduction of false recognition. Hub WJ-GXD900 L3 switch MPEG MPEG is a standard constituted by the ITU-TS (International Telecommunication Union - Telecommunication Standardization Sector) and ISO (International Organization for Standardization) for the compression/expansion of digital video images and voice. The Motion Picture Experts Group, a subordinate organization to the ISO, which was responsible for setting the standard, simply represents the title of the standard. MPEG2 is a technology for digitally compressing video images. The data transmission rate covers a range from several Mbps to several tens of Mbps. It is capable of displaying 30 frames/second of 720 x 480-dot images. All in all, it features high-quality images that are also used for DVD-video discs and digital satellite broadcasting. WV-CU850 Hub WJ-MPU850 WV-CU850 MAJOR OPERATING CONTROLS APPEARANCE MPEG2 Encoder WJ-GXE900 2 Front View Rear View 6 7 8 9 10 11 12 TRIGGER OUT ALARM IN RESET 4 5 6 7 ON OFF 8 POWER 1 C ON SW2 3 RESET 4 5 6 Ethernet Port (100BASE -TX) 7 RS-485 Port (RS-485) 8 Trigger Output Terminal 9 Alarm Input Terminal 10 Reset Input Terminal Power Indicator Status Indicators Rotary Switch Dip Switches 1 - 8 Reset Button VIDEO IN VIDEO OUT AUDIO IN 13 14 15 2 ENCODER : WJ-GXE900 STATUS 1 LINK1 100 1000 ACT 2 3 4 5 6 7 DECODER : WJ-GXD900 16 17 3 8 4 9 1000BASE-T/ 100BASE-TX Rear View 10 2 7 13 12 1 V+ —G 4 3 210(8-1/4") 14 ON QUAD SIGNAL GND 4 3 5 6 7 8 Dip Switches Reset Button RS-232C Ethernet Port VIDEO OUT 9 Reset Terminal 10 Audio Output Connector 11 Video Output Connector 12 Cooling Fan 420(16-9/16") 15 OFF AUDIO OUT Power Indicator Network Status Indicators Status Indicators Rotary Switch 2 1 WJ-GXD900 5 6 11 MIX RESET RESET 10.5 8 SW2 40 1 ON 6.5 C 44 B SW1 POWER (7/16") (1-3/4") (1/4") A (1-9/16") OPERATE BLINKING TEMPERATURE WARNING 1 2 3 4 OFF SIGNAL GND 11 Cooling Fan 16 Signal Ground Terminal 12 POWER Switch 17 Power Cord 13 Video Input Connectors 14 Video Output Connector 15 Audio Input Connector MPEG2 Decoder WJ-GXD900 Front View ON 1 WJ-GXE900 3.6 44 6.5 (1/8") (1-3/4") (1/4") 1 2 3 4 5 4 3 2 1 G 4 3 2 1 GGV + —G 100BASE-TX TERM RS-485 4 3 2 B SW1 270(10-5/8") 3 A 350(13-3/4") 2 300(11-13/16") STATUS 1 OPERATE BLINKING TEMPERATURE WARNING 13 POWER Switch 14 Signal Ground Terminal 15 Power Cord Unit: mm (inches) SPECIFICATIONS DECORDER : WJ-GXD900 ENCORDER : WJ-GXE900 Basic Specification Power Source Power Consumption Ambient Operating Temperature Ambient Operating Humidity Weight Dimensions Input/Output Video Input Video Output Audio Input Video Compression Method Audio Compression Method Resolutions Frame Rate Bit Rate Serial Port Alarm Input Trigger Output Reset Input Network Interface Network Interface Compatible Network Protocols Security Measures 120 V AC 60 Hz 23 W -10 °C - +50 °C (14 °F - 122 °F) Less than 90% (no-condensing) Approx. 2.9 kg (6.4 lbs.) 210 mm (W) x 44 mm (H) x 300 mm (D)[8-1/4" (W) x 1-3/4" (H) x 11-13/16" (D)] (Rubber feet excluded) 1.0 V[p-p]/75 Ω (Multiplex control signal), NTSC Composite, BNC (x4) 1.0 V[p-p]/75 Ω, NTSC Composite D-sub 9pin (x4) -10 dBv, more than 10 kΩ, Unbalanced, D-sub 9pin (x4) MPEG2-TS, SP@ML Dolby Digital® 720 x 480 pixels max. (Effective pixels: 704 x 480) 30 fps 1.5 Mbps, 3.0 Mbps, 3.8 Mbps, 4.6 Mbps, 6.1 Mbps, 9.2 Mbps RS-485, four-wire system, RJ-11, Termination resistor ON/OFF switch, 4,800 bps, 9,600 bps, 19,200 bps Dry contact, Terminal (x4) Open Collector output, Terminal (x4) Current loop or dry contact, Terminal (x1) 100BASE-TX, RJ-45 IP, ICMP, IGMP v2, BOOTP, TCP, UDP, HTTP, RTP, SNMP, NTP, FTP, DHCP Password authentication, Encryption of video and audio data (Hardware) Basic Specification Power Source Power Consumption Ambient Operating Temperature Ambient Operating Humidity Weight Dimensions Input/Output Video Output Quad Audio Output Audio Mixing output Video Compression Method Audio Compression Method Resolutions Frame Rate Bit Rate Serial Port Reset Input Network Interface Network Interface Compatible Network Protocols Security Measures 120 V AC 60 Hz 45 W -10 °C - +50 °C (14 °F - 122 °F) Less than 90% (no-condensing) Approx. 4.8 kg (10.6 lbs.) 420 mm (W) x 44 mm (H) x 350 mm (D)[16-9/16" (W) x 1-3/4" (H) x 13-3/4" (D)] (Rubber feet excluded) 1.0 V[p-p]/75 Ω, NTSC Composite, BNC (x4) 1.0 V[p-p]/75 Ω, NTSC Composite, BNC (x1) -10 dBv, 10 kΩ, Unbalanced, RCA (x4) -10 dBv, 10 kΩ, Unbalanced, RCA (x1) MPEG2-TS, SP@ML Dolby Digital® 720 x 480 pixels max. (Effective pixels: 704 x 480) 30 fps 1.5 Mbps, 3.0 Mbps, 3.8 Mbps, 4.6 Mbps, 6.1 Mbps, 9.2 Mbps RS-232C, D-sub 9pin, Only for maintenance Current loop or dry contact, Terminal (x1) 100BASE-TX, 1000BASE-T, RJ-45 IP, ICMP, IGMP v2, BOOTP, TCP, UDP, HTTP, RTP, SNMP, NTP, FTP, DHCP Password authentication, Decryption of video data/audio mixing (Hardware) SYSTEM REQUIREMENTS OS : Microsoft® Windows® 98 Second Edition / Microsoft® Windows® 2000 Professional Service Pack 3 / Microsoft® Windows® Millennium Edition / Microsoft® Windows® XP / Microsoft® Windows NT® Workstation 4.0 Service Pack 6a Computer : PC/AT Compatible CPU : Intel® Pentium® II (300 MHz) or higher Memory : 128 MB or more Monitor : 24-bit True color or better / Required to support XGA or higher picture resolution Network Interface : More than100Mbps Ethernet board must be installed Compatible Network Protocols : TCP/IP, UDP, HTTP, FTP, ARP, BOOTP CD-ROM Drive : Required to install the "Panasonic IP Setup" software and browse the operating instructions (pdf file) on the CD-ROM. Browser : Internet Explorer 5.5, 5.5SP2, 6.0, 6.0SP1 Acrobat® Reader : Required to browse the operating instructions on the CD-ROM. If Acrobat® Reader is not installed on the PC, download the latest version of Acrobat® Reader from the Adobe Systems Incorporated web site and install it. TRADEMARKS AND REGISTERED TRADEMARKS •Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation in the U.S. and/or other countries. •Intel and Pentium are trademarks of Intel Corporation. •Ethernet is a registered trademark of Xerox Corporation. •Adobe, Adobe logos, and Acrobat are registered trademarks of Adobe Systems Incorporated in the U.S. and/ or other countries. •Dolby Digital is a registered trademark of Dolby Laboratories. •Other names of companies and products contained in these operating instructions may be trademarks or registered trademarks of their respective owners. •Distributing, copying, disassembling, reverse compiling, reverse engineering, and also exporting in violation of export laws of the software provided with this product, is expressly prohibited. OPTIONAL COMPONENTS Weather Proof & Vandal Resistant Color Dome Camera WV-CW864A Super Dynamic II Color Dome Camera WV-CS854B Vandal Proof Super Dynamic II Color Cameras WV-CW474 Series 1/2-type CCD Color Surveillance Cameras Super Dynamic II Color Surveillance Cameras WV-CL920A Series WV-CP470 Series Lens : optional Color Monitors WV-CM2080 51cm (20") WV-CM1780 41cm (16") WV-CM1480 36cm (14") WV-CM1420 34cm (13") WV-CM1020 22cm (9") Lens : optional DISTRIBUTED BY: Panasonic Digital Communications & Security Company Unit of Matsushita Electric Corporation of America Security Systems Group http://www.panasonic.com/cctv Executive Office : Three Panasonic Way, Secaucus, New Jersey 07094 Zone Office Eastern : Three Panasonic Way, Secaucus, New Jersey 07094 (201) 348-7303 Central : 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205 Western : 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840 PANASONIC CANADA INC. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905) 624-5010 PANASONIC SALES COMPANY DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC. San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina, P.R. 00985 (809) 750-4300 Printed in Japan WJ-GXE900C (2P-516)