Transcript
EL1500CW
Outdoor Rated Ethernet & PoE Extender Description
Transmitter
The EL1500CW is another component of the NITEK EtherStretch line. Our EtherStretch solution allows for the utilization of existing cable infrastructure (coax or UTP) to transmit data from IP cameras and other network devices along with power (PoE) to operate these networked devices well beyond standard network limitations. The system can extend Ethernet up to 500m or 1640ft of coaxial cable making the EL1500CW is ideal for retrofitting existing installations. The EL1500CW is a system containing a transmitter housed in a NEMA 4X polycarbonate high-impact ABS molded enclosure which is ideal for use when installing the EtherStretch solution outdoors. The set also includes a receiver unit that requires very little installation time and no set up or configuration. The system quickly turns any ordinary RG59 coax cable into a high speed network communication and PoE path.
Receiver 6.732
4.764
Top (Side View)
0.591
NITEK
Top (Inside View)
1.07
Top (Outside View)
6.732
The EL1500CW is transparent to the network thus requiring no IP and MAC addressing. Simply connect your network devices to the networking port of the transmitter and receiver along with a cable between units and the system begins communicating. LED indicators show the status of network communication and PoE power. The EL1500CW requires no network settings to be changed or adjusted.
3.95" NITEK EL1500C
1.6
Made in USA Right
TOP
Left
Bottom
1.6
4.288 3.602
1.07
The units are constructed of industrial grade RoHS compliant plated aluminum which is finished with a corrosion resistant finish making it very durable.
4.95"
Bottom (Inside View)
Bottom (Outside View)
6.260
7.125
Bottom (Side View)
Features
7.125
Available PoE Wattage At PoE Device 26.3 25.0
18.4
Watts
15.0 15.4
●
Transmitter housed in a NEMA 4X rated enclosure for outdoor applications
● ●
Fully transparent to the network
● ● ● ● ●
Easy to install, no set up required
12.7
15.4 12.2
10.0
9.6
8.2
5.0 0.0
Supports 10/100 and PoE over RG59 cables up to distances of 500 meters (1640 feet)
22.2
20.0 15.0
●
100 Meters 328 Feet
200 Meters 650 Feet
300 Meters 1,000 Feet
400 Meters 1,300 Feet
500 Meters 1,640 Feet
802.3AT
26.3 Watts
22.2 Watts
18.4 Watts
15.0 Watts
12.7 Watts
802.3AF
15.4 Watts
15.4 Watts
12.2 Watts
9.6 Watts
8.2 Watts
NITEK
®
USA
* Results charted were calculated using RG59U coaxial cable with a 20AWG center conductor and power sourcing equipment using IEEE 802.3AF standard with starting voltage of 48 volts DC and IEEE 802.3AT standard with starting voltage of 54 volts DC. PoE Switches with internal power and current limits may change individual results.
Supports any network device, including mega-pixel technology IP cameras No MAC or IP addressing required LED indicators for network signals, link status and power Ground loop isolation Made in the U.S.A.
Patent Pending
IEC/UL 60950-1
5410 Newport Drive, # 24 Rolling Meadows, IL 60008 Phone: (847) 259-8900 Fax: (847) 259-1300 E-mail:
[email protected] WWW.NITEK.NET
EUROPE
1.640
De Schans 19-21 2a 8231 KA Lelystad Tel: +31(0)320-230005 Fax: +31(0)320-282186 E-mail:
[email protected] WWW.NITEK.NL
PRODUCT SPECIFICATION
10292013
TECHNICAL SPECIFICATION Network Transmission Device Network Port
RJ45 Connector
Link Port
BNC Coax Jack
Ethernet
100BASE-TX Full Duplex
Dimensions Transmitter Enclosure Receiver
6.73” x 4.76 X 2.17 1.1” x 1.6” x 5.1” including tabs & BNC
Operating Temperature
-15° to 75° C / 0° to 167° F
Shipping Weight
5 lbs
Common Installation Type Monitor
Outdoor IP Camera
PoE
PoE
Data
PoE NVR
Data Data
PoE Network Switch
P/T/Z Controller Monitor *PoE is introduced to the system by using a PoE injector (IP1054) in installations where the network switch in not capable of producing power
NVR PoE Data
PoE
Data
PoE Data
“No PoE” Network Switch P/T/Z Controller
