Ns 4000 - Kongskilde

Transcript

NS 4000 0. Contents 1. General Page Foreword Technical specifications Accessories Safety precautions 1.1 1.2 1.3 1.4 2. Mounting and adjustment Commissioning Coupling Mounting of tank unit Mounting of coulter kit Row spacing Marker shifter Markers Marker arms, spring bolts Marker arms in transport position Hydraulic hose, marker Removal Removal of coulter set Removal of tank unit Following harrow Mounting of following harrow Tramlining Pre-emergence markers 2.1 2.2 2.2 2.4 2.5 2.6 2.6 2.6 2.6 2.7 2.7 2.7 2.7 2.8 2.8 2.9 2.10 3. Adjustment Test sowing General Test sowing of the drill Agitator shaft Bottom flaps Seed housing shutters Emptying of machine Version NS 4000 B 3.1 3.1 3.1 3.1 3.1 3.1 3.1 0.1 NS 4000 0. Contents Page Test sowing Gear cassette position Scale setting Blower Bottom flaps under seed housings Filling of seed Starting the seed flow Turning the test sowing handle Weighing Calculation of sowing rate Adjusting the sowing rate Discrepancies in the sowing rate After test sowing Blower Special crops Special crops Sowing of grass seed Warning Sowing of small round seeds Mounting of fine seed fingers Disengagement of sowing wheels Mounting of peg wheels Sowing table Sowing table Coulter pressure/sowing depth Coulter pressure/sowing depth Coulter tightening Markers Adjustment of markers Centre marking Marking track Following harrow Adjustment of following harrow Transport position 0.2 Version NS 4000 B 3.2 3.2 3.2 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.4 3.4 3.4 3.4 3.4 3.4 3.4 3.5 3.5 3.5 3.5 3.7 3.7 3.8 3.8 3.8 3.9 3.9 3.9 3.9 3.10 3.10 3.10 NS 4000 0. Contents Page 4. Operation Generally Driving speed Emptying of seed hopper Land wheel Lid 4.1 4.1 4.1 4.2 4.2 5. Maintenance and lubrication Adjustment of chains Fine adjustment of bottom flaps Cleaning of seed outlets and sowing rollers Lubrication Winter storage 5.1 5.1 5.1 5.1 5.2 6. Spare parts Register Version NS 4000 B 6.1 0.3 1.General Foreword Nordsten would like to congratulate you on your new NS 4000 seed drill which we are convinced will serve you well in your work. In order to use the machine correctly and safely, we recommend that you familiarise yourself with it by studying this instruction manual. The correct use of the machine, along with careful maintenance, lubrication and storage, will help to keep it in good working order. Type of machine:............................ Date of purchase:........................... Manufacture number:..................... Version NS 4000 B 1.1 1. General Technical specifications Machine type NS 4030 Working width, cm 300 300 400 400 Overall height, cm (HK30S) 180 180 180 180 Overall width, cm (HK30S) 300 300 300 300 Filling height, cm (HK30S) 170 170 170 170 Row spacing, Euro coulters 24 24EU Row spacing disc coulters NS 4030 24ER NS 4040 32EU NS 4040 32ER 32 24 32 Row distance, cm 12,5 12,5 12,5 12,5 Distance between coulter rows, cm 36 36 36 36 Hopper capacity, liter 800 800 800 800 Hopper capacity, kg wheat 615 615 615 615 Weight of hopper 325 325 325 325 Weight of coulter section 400 425 450 480 Weight of coulter section w/rear harrow 490 515 540 570 Total weight (hopper, coulter section and rear harrow) 815 840 865 895 1.2 Version NS 4000 B 1.General The seed drill can be fitted with the following accessories: Following harrow type Max-Flow. The following harrow has rearwardfacing tines which ensure that plant residue, such as straw and similar materials, is less likely to drag. Following harrow type Wing-Flow. The following harrow has rearward-curved L-tines. Recommended in connection with disc coulters since dragging and visible ridges are avoided. Following harrow type Twin-Flow. A double following harrow can be mounted, instead of the traditional following harrow, by fitting on the rearmost set of Euro coulters. Electronic tramlining system AGRO TRAM 2100. This can be mounted on the seed drill in order to make tracks of up to nine bouts of the seed drill’s width. AGRO TRAM 2100 is equipped with seed shaft control and acremeter for measuring both part and total area. The sowing rate is automatically reduced, to take account of tramlining. Accessories 2100. Pre emergence markers for making tracks for fertilisation and spraying before germination. Only available with AGRO TRAM 2100 and MaxFlow/Wing-Flow following harrows. Mechanical regulation of sowing rate whilst driving, allowing the rate to be controlled from the tractor cab. Direct mechanically driven areameter. Depth limiters for Euro coulters. Depth limiters for disc coulters. Grass seed foot for mounting on the Euro coulters. Enables sowing of grass seed in 80 mm row widths when the soil is suitably dry and free of foreign bodies. Seed hopper extension 400 l. Hydraulic top link for lifting of coulter set. Electronic level control indicator for hopper capacity. Used in connection with AGRO TRAM 2100. Extension cable for AGRO TRAM Version NS 4000 B 1.3 1. General These instructions and safety notes in this instruction manual must be followed. Safety distances The safety distance to the seed drill while in operation is 4 metres. Persons must under no circumstances be on the seed drill while it is running. Safety when lifting the seed drill The indicated lifting eyes should be used when lifting the seed drill and when carrying out repair of the seed drill’s main frame. Safety precautions concerning guards Guards for chains, gear wheels and rotating shaft ends etc. must be fitted to comply with the required safety regulations. Loose guards, which include calibration trays and seed hopper lid, should be fitted and closed when the machine is running. The agitator shaft in the hopper is not shielded. Therefore, to avoid injury, hand stirring of the sowing material whilst the machine is running must be avoided. 1.4 Safety precautions Fixed guards should be removed and fitted using tools. Safety precautions concerning hydraulics Safety precautions whilst driving Hydraulic systems with a working pressure of up to 200 bar must be treated with care. When carrying out repairs, the hydraulic system must be without pressure. Air in the hydraulic system can lead to incorrect functioning of the machine, and thus should be expelled before the machine is used. When driving on public roads, road traffic laws concerning lights, safety, etc. should be followed. Lift arm pins and top link pins should be properly secured in order to avoid accidents. On safety grounds, marker arms should always be locked in position when driving on public roads. Locking is carried out using lock fittings which are mounted on the locking pin and secured with a ring pin. See fig. 2M and 2N. Safety precautions concerning tightening Safety precautions when parking Product liability Always place the seed drill on firm, horizontal ground when it is removed from the tractor. Ensure that the support legs are mounted and secured by the locking pin. Safety when cleaning Cleaning and maintenance of the seed drill should only be carried out when the machine is not running. Version NS 4000 B Tighten all bolts after the first 25 hours of operation. All bolts should be subsequently tightened before the start of each season. Nordsten’s product liability covers machines which are defective on delivery. Product liability no longer applies if modifications are made to the seed drill or its accessories without Nordsten’s explicit written permission. It is also a condition of the product liability that the seed drill is only used for purposes described in this instruction manual or for purposes which have Nordsten’s permission. 1.General Safety precautions Finally, it is also a condition that the seed drill is used with all fixed guards fitted. Version NS 4000 B 1.5 2. Mount. and adjustment Commissioning the seed drill Immediately after receiving the drill, it and any extra equipment should be checked to ensure that the items received are in accordance with the order and that there are no defects or missing parts. Any claims should be immediately forwarded to the dealer. Commissioning driving wheel, gearbox, agitator shaft and sowing shaft are correctly adjusted. This is particularly importtant if extra equipment with chain drive has been fitted. Any necessary adjustments should be carried out as described in section 5. Chains and linkages should be lubricated with oil. In the case of damage occurring during transport, claims should be forwarded to the transport firm used. Otherwise reference is made to Nordsten’s usual terms of sale and delivery. The coulter settings - and thus their relative spacing - may have changed during transport. The coulter settings should therefore be checked (see section coulter spacing) and any necessary adjustments carried out as described. Check that the chains between the Version NS 4000 B 2.1 2. Mount. and adjustment Mounting of tank unit on cultivation equipment We further refer to the spare parts list for coupling kit. The two hooks are mounted on the rear sides of the headstock of the cultivation equipment. See fig. 2A. On the Howard power harrow HK 32 the hooks are integrated in the machine and have, therefore, not to be mounted. The bracket to connect the tank unit to the top of the headstock is now mounted. See fig. 2B. The cultivation equipment can be placed under the tank unit and lifted up so that the suspension points of the tank unit are caught by the hooks. See fig. 2A and 2C. A pin is placed in the top bracket and locked by a ring pin. See fig. 2B. Locking bolts are mounted to lock the tank unit. See fig. 2C. The machine is lifted and the supporting legs can now be re-moved. Fig. 2C. Lock bolts. Machine with hydraulic driven blower The tank unit should be situated on a flat surface. The supporting legs are placed so that the cultivation equipment passes between the two legs. Fig. 2A. Mounting of hooks. Coupling In the case of an hydraulic driven blower the following demand is made on the hydraulic system of the tractor. Fig. 2B. Foremost top bracket. The blower requires up to 30 l/min at a pressure of about 125 bar. The hydraulic system of the tractor must be able to produce 8 kW continuously for runing the blower. On newer tractors it is possible to adjust the oil quantity on the individual oil outlets. The oil flow is adjusted at the tractor valve first, so that the values stated for blower pressure are observed. Max. 60 mbar. 2.2 Version NS 4000 B 2. Mount. and adjustment Coupling output. E.g. 1000 rpm PTO speed. 3. Screw in adjuster to get recommended air pressure. Fig. 2D. Hydraulic driven blower. On tractors without the possibility for controlling the flow of oil from the external hydraulic spool valves, the air pressure can be set on the regulator valve. See fig. 2D. On connecting hydraulic hoses the probes should be cleaned before installing. Connect the red hose P (pressure) to the tractor's external service. The green hose R (return) must be fitted to a free flow return (pressureless). On tractors without a freeflow return the dealer must establish one. On drills fitted with a PTO driven fan, a gearbox is mounted on the output shaft of the power harrow and is driven at 1000 rpm. The PTO shaft is connected to the gearbox splined shaft and locked with a bolt. The cardan joint on this end of the PTO shaft is lubricated for life. The other end of the shaft mounted to the drill should be lubricated after evry 16 hours work. See fig. 2F. Fig. 2F. PTO shaft. The V belt tension for the fan drive is via an idle tension roller. See fig. 2G. On Howard HK power harrows the levelling board handles are replaced with hexagon nuts. See fig. 2G. Fig. 2E. Mounting of gearbox. Fig. 2G. Tension roller. Set air pressure as follows: 1. Make sure valve is fully open (screwed out). 2. Run tractor with spool valve in flow at an engine speed equal to pto Version NS 4000 B 2.3 2. Mount. and adjustment Mounting of coulter kit on cultivation equipment We further refer to the spare parts list for coupling kit. Hoses from the seeding houses are installed, passing under the narrow foot board and to the distributor heads. A bracket is mounted on each end of the packer roller arm of the cultivation equipment. See fig. 2H. Remember to connect the seeding hoses, which are fitted with a coupling to reduce the sowing rate, to the distributor heads equipped with flap valves for tramlining. The coulter kit can now be mounted with link arms, top link and support spindles. Fig. 2H. Mounting of coulter kit. A cross bar between the link arms is mounted. The top link is now adjusted to place the coulter frame horizontal. 2.4 Coupling Version NS 4000 B Fig. 2I. Foot board. 2. Mount. and adjustment Row distance The distance between the coulters is measured directly on the coulters themselves - and thus not on the suspension arms. The use of a measuring implement with the actual row spacing marked is recommended. Remember to tighten all bolts after adjustment. Fig. 2J. Clamp with bolt. Row distance Fig. 2I. Row distance. Changing and adjusting the row spacing can be carried out by moving the suspension arms and clamp for each coulter sideways on the coulter bar. This can be done after the bolts under the clamps have been loosened. See figure 2J. Version NS 4000 B 2.5 2. Mount. and adjustment Markers The seed drill is fitted with hydraulic markers. If both markers are required in their working position, the marker system is activated in the following way: Marker shifter Marker arms in transport position When transporting the seed drill on public roads, the marker arms must be locked up. A single-acting hydraulic take-off from the tractor is used which activates a shuttle valve (see fig. 2K) in the following way: The marker which is in its working position is raised about 1 metre. The hydraulic pressure is then removed from the system, after which both markers will move into their respective working positions. On supplying hydraulic pressure to the marker system, both markers go to vertical. Marker arms, shear bolt By removing hydraulic pressure from the marker system, one marker will move into its working position. The marker arms are equipped with a shear bolt which is released when overloaded. Carrying an extra shear bolt (M6 x 75 grade 8.8) is recommended. See fig. 2L. In order to reduce the transport height on 4,0 m machines the marker arms are articulated. Both in the "folded" position (during transport) and in the working position the link must be locked with a locking pin, secured with a ring pin bolt. See fig. 2N. Fig. 2K. Shuttle valve for marker. Fig. 2L. Shear bolt. Fig. 2M. Locking pin for transport. 2.6 Version NS 4000 B Shifting between the markers (i.e. between left and right) is done by supplying, and then removing, hydraulic pressure from the system. The locking can be made by lock pins which are put under the support of the marker arms. The lock pins are secured with a ring pin. See fig. 2M. 2. Mount. and adjustment Removal Hydraulic hose, marker Removal of tank unit The hydraulic hose for the marker arms is connected to the tractor. Supporting legs are put onto the tank unit. If the tractor is provided with an outlet for an assistor cylinder, this outlet is used. The hydraulic hoses and any wires for light and tramlining are disconnected. If the tractor is not provided with such an outlet, the hydraulic hose is connected to the outlet of a singleacting remote cylinder. If necessary the air hoses from the cultivation appliance are loosened. Removal of coulter kit Always park coulter kit and tank unit on a horizontal and firm ground, when disengaging. In the case of PTO driven blower the pulley (behind blower) and the tension arm are loosened. Then the belts can be removed. See fig. 2F. Lock bolts and pin fig. 2B and 2C are removed. Supporting legs are put onto the coulter bar. Fig. 2N. "Folded" marker arm. Hoses for the distributors are removed. Remove the guard on the side of the tank unit to remove the long cassette for the land wheel. Link arms, top link pin and spindles are removed. Version NS 4000 B 2.7 2. Mount. and adjustment Mounting of following harrow The following harrow is delivered as harrow sections and mounting parts. The mounting parts include: Following harrow arms, U-brackets, tubes for track and folloiwng harrow module. Mounting is carried out as follows: The parallel suspended link arms are mounted on the main frame of the coulter bar. See fig. 2O. Fig. 2O. Following harrow arms. The top links are mounted from the upper arms to the uprights on the coulter bar. U-brackets are mounted on the following harrow module. Fig. 2P. Working angle of the following harrow. The angle adjusting plates are mounted around the frame of the following harrow and in the Ubracket. See fig. 2P. The working angle of the following harrow and the working depth are adjusted to obtain the harrowing effect wanted. See also chapter 3: Adjustment of following harrow. 2.8 Version NS 4000 B Following harrow 2. Mount. and adjustment Tramlining Tramlining Agro Tram 2100 can now be mounted for controlling tramlining. We further refer to instruction for Agro Tram 2100. On two distributor heads hydraulic cylinder for opening and closing of the outlets for the distributor is mounted. See fig. 2Q. A stainless disc closes two outlets in the distributor head. Fig. 2R. Wheel sensor. A solenoid valve for control of tramlining is mounted on the marker shuttle valve. See fig. 2R. The sowing rate is reduced automatically by a solenoid clutch on the side of the seeding housings. See fig. 2T. A wheel sensor is mounted on the input shaft on right side of the seed drill. See fig. 2S. The clutch stops the outer roller on left side, when tramlining. See fig. 2T. Fig. 2Q. Flap valve. Fig. 2S. Solenoid clutch. Version NS 4000 B Fig. 2T. Sensor for control of "tracknumbers" On the marker arm a sensor is mounted for control of "tracknumbers" for the tramlining. See fig. 2T. 2.9 2. Mounting of pre-emergence markers Fig. 2U. Solenoid Valve. Mounting of preemergence markers The pressure hose (A) on the change-over valve to the markers are dismounted. The supplied T-piece is mounted where the hose was before, and the valve block is mounted upon the T-piece. The pressure hose is mounted on the side branch of the T-piece. See fig. 2U. The bracket (B) is mounted on the following harrow with M10x130 bolts. The marker arm (C) is mounted on the bracket with U-bolts. The marker disc can be mounted both inwards and outwards. Fig. 2V. Left cylinder. On the bracket is also mounted the ring holding the hydraulic hoses. See fig. 2V. On the cylinder to the left the Tpiece is mounted with the side branch. The left cylinder is connected to the solenoid valve with the other hydraulic hose. See fig. 2X. On the cylinder to the left the angle is mounted. Right and left cylinders are connected to one of the hydraulic hoses, in a way that leads the hoses through the eyes on the harrow tines. See fig. 2X. 2.10 Fig. 2X. Right cylinder. The wire from the solenoid valve is connected to the 7 pin socket plug, on the coulter frame. Brown wire is connected to terminal 7/58L and blue wire to terminal 4/R. Version NS 4000 B 3. Adjustment Test sowing General Bottom flaps Seed housing shutters Before sowing begins, the following should be carried out: The bottom flaps should be as close as possible to the seed wheels without damaging or squeezing the seed. The shutters must not be used for adjusting the rate of sowing. - Test sowing of the drill - Setting coulter pressure/sowing depth The bottom flaps can be adjusted using the handle at the end of the hopper. See figure 3B. - Setting the drive wheel - Setting the markers. Test sowing of the drill Test sowing includes both a calibration depending on the weight/size of the seed (1000 grain weight), and the adjustment of the sowing rate per unit area. The scale setting for different seed sizes should be as follows: Fine seed Corn Peas, etc. : : : 1 2-3 3-6 Table 3A. Adjustment of bottom flap position. The shutters should always be completely open or closed. If you wish to start sowing with half the sowing width, the shutters at one side can be closed. Emptying of machine The calibration bags are mounted under the seed housings and the bottom flap handle is turned backwards. Exchange of seed wheel See special crops chapter 3.4. Agitator shaft The agitator shaft always runs. It is not necessary to disengage the agitator shaft when sowing large seed, e.g. peas and beans. Fig. 3B. Handle for bottom flaps. Version NS 4000 B Fig. 3C. Seed housing shutters. 3.1 3. Adjustment Test sowing Test sowing Gear cassette position The test sowing is carried out to ensure the correct sowing rate, and is carried out as follows: The gearbox allows continuously variable regulation of the seed roller’s speed. The correct sowing rate can be adjusted using the formula: The gearbox has two different working ratios: a low and a high, the high being a direct continuation of the low. By turning the gear cassette on the side of the gearbox, the high or low ratio can be selected. NO. OF PLANTS PER M² X TCW = KG / HECTARE GERMINATION PERCENT IN THE FIELD The position of the cassette is chosen according to the sowing table in this instruction. Table 3O page 3.6.. The cassette can be rotated only after removal of the ring pin in the centre. It is important to remember to replace the pin after changing ratios. TCW = 1000 grain weight After this preliminary adjustment the test sowing should be carried out. The low ratio is engaged when the cassette is positioned with the largest wheel upwards. This ratio is used for sowing small seeds such as rape and clover. The high ratio is engaged by positioning the casette with the largest wheel downwards. This ratio is used for grain and larger seeds. Fig. 3D. Cassette position, high (2). 3.2 Fig. 3E. Scale setting. Version NS 4000 B Scale setting, Vario-Exact gearbox Initially,the scale should be set to the correct sowing rate according to previous records or to the sowing table 3O on page 3.6. 3. Adjustment Test sowing Blower Starting the seed flow Weighing The blower must not be run during the calibration. Attach the test sowing handle and turn it clockwise until the seed flows from all of the outlets. Weigh the seed from the sowing tray(s) on an accurate pair of scales. Empty the contents of the calibration bags into the seed hopper. The spring loaded bottom flaps under each seed housing are opened. See fig. 3F. Calculation of the sowing rate Turning the test sowing handle To obtain the sowing rate for 1 ha., the measured weight must be multiplied by 20. The calibration bags are hooked below. See fig. 3H. Turn the test sowing handle according to the table 3G below: Bottom flaps under seed housings. Filling of seed Fill sufficient seed in the hopper such that the agitator shaft is still covered after a test sowing has been carried out. Fig. 3F. Bottom flaps below seed housings. 1/20 HA NS 4030 86 NS 4040 42 1/10 Acre 69 34 Table 3G. Turn the handle x number of revolutions per 1/20 ha. or 1/10 acre. Fig. 3H. Calibration bag. Adjusting the sowing rate If the calculated sowing rate corresponds to the required rate, then the machine is correctly adjusted. If the sowing rate is not correct, the following adjustment can be made by changing the scale setting. If a larger sowing rate is required, the regulating handle’s indicator should be adjusted to correspond to a higher value on the scale. After adjustment of the scale setting, a new test sowing should be carried out. Version NS 4000 B 3.3 3. Adjustment Discrepancies in the sowing rate If the test sowing has been carried out carefully, the actual and calculated sowing rates should correspond exactly. If this is not the case in practice, then the cause could be that the test has not been carried out corrrectly or that an inaccurate pair of scales has been used. However, another potential cause of discrepancies is unusual soil conditions. Very wet or very loose soil can cause inaccurate rolling of the drive wheel. If problems are caused by the soil conditions, then a supplementary calibration test in the field is recommended. Test sowing in the field follows essentially the same procedure as the standard test sowing. Special crops NS 4030 NS 4040 1/20 HA 1/10 Acre Special crops 167 m 125 m When sowing special crops, certain precautions may have to be taken. 148 yds 111 yds Tabel 3I. Drive x number of meters for 1/20 ha. or 1/10 acres. After test sowing The calibration bags are removed. The bottom flaps under the seed housings are closed. Blower The blower is engaged and the working pressure - read on the pressure gauge (fig. 3J) - is adjusted according to table 3O page 3.6. Fig. 3J. Pressure gauge, air pressure. Sowing of grass seed requires special attention since the seeds can „bridge“ in the hopper, thus affecting the actual sowing rate. This problem will be particularly acute if the hopper is exposed to vibration. It is therefore advisable to carry out test sowing with a limited amount of seeds in the hopper, and to avoid filling the hopper completely until in the field where sowing is due to take place. In addition, regular stops to manually stir the hopper contents is recommended in order to achieve uniform sowing. Warning However, instead of turning the test sowing handle through a specified number of revolutions, the seed drill is driven in normal working position a specified distance in the field with the calibrations bags mounted. See table 3I. 3.4 Sowing of grass seed Owing to the agitator shaft, stirring of the hopper contents should only be carried out when the machine is switched off. Version NS 4000 B 3. Adjustment Special crops Sowing of small round seeds Disengagement of sowing wheels When sowing small, round seeds, such as turnip, white mustard and rape the fluted sowing wheels are exchanged for peg wheels with fine seed fingers. The sowing rate is reduced to 1/9 and at the same time waste is avoided since the seeds are only fed out by the pegs. The covers above the seed wheels are disengaged by loosening the black thumbscrew at the front of the seed housing. Mounting of fine seed fingers The fine seed fingers are fitted by pressing them over the rollers. As the roller is turned, the fine seed fingers are pulled round to cover the roller. The fine seed fingers are shaped so that they are held in place. See figure 3K. The R-clip at left side of the seed housing (at bearing) is removed and the bearing is pushed out of the bearing retainer. The sowing shaft can now be pushed fully to the right, and the bearing at right side comes out of the bearing retainer. The sowing shaft can now be lifted out of the seed housing. See fig. 3L and 3M. Fig. 3K. Mounting of fine seed fingers. Fig. 3L. Removing of seed wheels/ shaft. The shaft connections on both sides of the seed housings are removed. The R-clips are removed. Version NS 4000 B Fig. 3M. Removing of seed wheels/ shaft. Mounting of peg wheels The solenoid clutch (for tramlining) is moved over to the peg wheel shaft. See fig. 3M and 3N. Fig. 3N. Sowing shaft with fine seed fingers. 3.5 3. Adjustment Special crops The sowing shaft is put down onto the seed housing and the seed wheels are slid down into the seed housing. The bearings are pushed back in position and locked by an R-clip. The shaft connections are now completed. When peg wheels with fine seed fingers are used the bottom flap handle is placed in position 1. 3.6 Version NS 4000 B 3. Adjustment Sowing table Sowing table The sowing table shows the calibration of the drill and the scale setting for the required amount per hectare. Note that the sowing table is only a guide, a test sowing should always be carried out to check the scale setting. Seed Barley Wheat Rape Peas Bottom flaps 2-3 2-3 1 3-6 Cassette position 2 2 1 2 Seed wheels Fluted wheels Fluted wheels Peg wheels fine seed fingers Fluted wheels Airpressure (bars) 60 60 30 60 Row spacing (cm) 12,5 12,5 12,5 12,5 1,1 1,5 1,9 133 Scale setting 5 10 15 20 25 30 35 40 45 50 100 115 130 145 160 116 133 151 168 186 2,3 2,7 3,1 3,5 3,9 154 175 196 218 240 55 60 65 70 75 176 191 206 221 236 204 221 239 256 274 4,3 4,7 5,2 5,6 6,0 263 286 309 333 358 80 85 90 95 100 252 266 282 292 6,4 Table 3O. Version NS 4000 B 3.7 3. Adjustment Couter pressure /sowing depth The coulter adjustment can be adjusted individually for each coulter. This is done by changing the position of each spring by moving the chain one or more links on the coulter arm. With this individual adjustment it is possible to obtain an increased coulter pressure on the coulters working behind the tractor wheels. See fig. 3Q. Coulter pressure/sowing depth In order to achieve the desired sowing depth on all coulters, it is necessary to adjust both the coulter pressure and the telescopic arms correctly. Coulter tightening The tension of the spring determines the sowing coulter’s working depth in the soil. Note also that a too-high forward driving speed can also result in non-uniform sowing depth. Central coulter adjustment can be carried out on all coulters at the same time. Machines with a working width of 4,0 m are provided with two spindles. Central coulter adjustment is carried out by turning the spindle with the calibration handle or openend spanner. See fig. 3P. 3.8 Fig.3Q. Individual coulter pressure. Fig. 3P. Central coulter adjustment. Version NS 4000 B 3. Adjustment Adjustment of markers The markers are used to make a marker track. The track ensures that the outer coulter in one row is both parallel to and correctly spaced with respect to the previous row. Centre marking The seed drill has centre marking. Thus the distance from the outer coulter track to the marker track should be half the width of the seed bed plus half a row spacing. This adjustment can be carried out most easily by driving forward a few metres with the markers and the sowing coulters lowered into their working positions, such that the tracks can be clearly seen in the soil. Markers Alternatively, the marker is set 3.0 m out, as measured from the centre of a 3.0 m seed drill, 4.0 m out on a 4,0 m machine etc. Marking track The marking track’s width can be adjusted by turning the cranked marker shaft. See figure 3S. The narrowest track is obtained by turning the shaft downwards such that the marker is parallel to the direction of travel. The widest track is obtained by turning the shaft such that the marker is angled backwards with respect to the direction of travel. Fig. 3R. Centre marking. Fig. 3S. Cranked marker shaft. The shaft should not be turned upwards or angled forwards with respect to the direction of travel as this can damage the shaft and give a poor track. The marker arms can be locked in a vertical position when driving on public roads or when driving close to fences, etc. Version NS 4000 B 3.9 3. Adjustment Following harrow Adjustment of following harrow The following harrow can be set for light or heavy harrowing, or placed in a transport position. Adjustment is carried out by turning the top links between the coulter bar and the harrow arms. Coarse adjustment can be made by moving the top links one hole in the upper marker arms. See fig. 3T. To obtain an optimum working effect it is possible to adjust the working angle of the harrow tine. See fig. 3U. Fig. 3T. Adjustment of harrowing depth. 3.10 Fig. 3U. Working angle of following harrow. Version NS 4000 B 4. Operation Generally that the chain drive is correctly adjusted. During operation check continously that no sowing coulters are blocked. that seed rollers and bottom flaps are intact. In order to avoid blockage of the coulters, it is advisable to only raise and lower the seed drill when driving forwards. that bottom flaps are able to move freely - this can be checked using a finger or a thin shaft. Regularly check that there is sufficient sowing material in the seed hopper. that coulters are intact (not worn out). that the coulter arms are able to move freely and have the correct spring tension. that the marker position is correct - check frequently. that the air pressure is correct during sowing. Regularly check whether the actual sowing rate corresponds to the calculated rate. Both before and during sowing work, attention should be paid to the following.: that the lift arms of the tractor are correctly working. that the coulter set is horizontal when the machine is lowered to its working position. that the gearbox is in a good condition - gear wheels and gear bearings. that the oil level in the gearbox is visible in the oil-level glass (Vario-Exact). Emptying of seed hopper The seed hopper is emptied by opening the bottom flaps below the seed housings and by hooking on the emptying bags. The handle for the bottom flaps should then be pulled back completely such that any excess sowing material is emptied into the emptying bag. See fig. 3H. Driving speed During the sowing work the speed should be 5-8 km/h. In general speed should depend on the prevailing conditions and, in particular, oscillation of the machine should be avoided. Version NS 4000 B Fig. 4A. Land wheel in transport position. 4.1 4. Operation Land wheel The land wheel must during transport be locked in a transport position. See fig. 4A. Lid The lid can be locked during transport. See fig. 4B. Fig. 4B. Lid. 4.2 Version NS 4000 B 5. Maintenance and lubrication Adjustment of chains Sprocket wheels for the adjustment of the chain should be loosened. The sprocket wheels should then be pushed upwards until the chains are at the correct tension, at which point the sprocket wheels should be tightened again. See figure 5A. Fine adjustment of bottom flaps Cleaning of seed outlets and sowing rollers Cleaning the seed outlets and seed rollers can be facilitated by removing the sowing shaft. See page 3.5. Lubrication The gearbox oil must be visible in the level eye, otherwise it must be refilled with one of the following types of oil: Texaco Raudo HD 15 Raudo HD 22 Raudo HD 32 Fig. 5B. Adjustment of bottom flaps. Shell Tellus Oil Tellus Oil (S) 32 Tellus Oil 32 Statoil Hydraway HM 15 Hydraway HM 32 ESSO Nuto H 15 Nuto H 32 The bottom flaps should be set to the highest position (position 1). Adjustment can then be carried out by turning the screw on the rear face of each bottom flap until the distance between the flap and the seed roller is 1 mm. See figure 5B. All chains should be lubricated regularly. After each season, the chains should be cleaned in petroleum and then lubricated with oil. Fig. 5A. Sprocket wheels. Before each new season all linkages and chain tighteners should also be lubricated. Version NS 4000 B 5.1 5. Maintenance and lubrication Wheel arm, marker arms, marker hub and the cardan joint should be regularly greased. See fig. 5C, 5D, 5E and 5F. For PTO driven blower the cardan shaft should also be greased regularly during the season. All bearings are self-sealed and do not require lubrication. Winter storage Careful cleaning of the seed drill after each season is recommended. The machine should also be prepared in plenty of time before the start of the new season. The seed drill should be protected from the elements during storage. To prevent vermin damage, during storage, it is important to fully clean the hopper and associated metering unit. Fig. 5C. Lubrication of wheel arm. Fig. 5D. Lubrication of marker arms. 5.2 Version NS 4000 B Fig. 5E. Lubrication of drive joint. Fig. 5F. Lubrication of marker hub. 6. Spare parts list Spare parts register and belonging drawings are divided as follows: Page Lid 6.4 Seed hopper 6.6 Transmission 6.8 Gearbox 6.10 Agitator parts for seed hopper 6.12 Fan, PTO 6.14 Fan, PTO 6.16 Fan, hydraulic 6.18 Hydraulics for fan 6.20 Scale 6.22 Supporting legs for tank 6.24 EURO coulters 6.26 Disc coulters 6.28 Plan EURO coulters 6.30 Plan disc coulters 6.31 Version NS 4000 B 6.1 6. Spare parts list Page Distributor 6.32 Landwheel 6.34 Inside marker arm 6.36 Outside marker arm 6.38 Hydraulic for marker kit 6.40 Following harrows 6.42 Foot board 6.44 Supporting legs for coulter kit 6.46 Pre-emergence marker 6.48 Hydraulic f. pre-emergence marker 6.50 6.2 Version NS 4000 B 6. Spare parts list Version NS 4000 B 6.3 6. Spare parts list 6.4 Lid Version NS 4000 B 6. Spare parts list Lid Position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 18 19 20 21 22 22 23 24 25 26 27 28 29 30 Version NS 4000 B Ref. Description 2155936 2152489 0602194 540225 546206 544106 2152491 547220 2152492 2155935 2155621 544609 550216 550220 546208 546508 544108 2152602 2152603 550230 2152493 600160 2152372 2152373 540490 43401 2152494 540470 356316 556840 356315 356310 Cover part, front Clamp Handle 30 x 170 mm Set screw M6 x 25 Face plate M6 Nut M6 din 934-8 Retainer Split pin Ø3,2x20 din94 Washer Ø17/Ø11,5/2,0 Cover part, rear Bracket Self-locking nut M8 din985 Set screw M8 x 16 Set screw M8 x 20 Face plate M8 Spring washer M8 Nut M8 din 934-8 Retainer for cover, right Retainer for cover, left Set screw M8 x 30 Chain nr. 40 - 16 led Handybolt std. 1/4" x 1/2" Bracket for gas spring, left Bracket for gas spring, right Steel bolt M8 x 90 Gas spring Strap for cover Steel bolt M8 x 70 Retainer f. rubber strap Pop rivet Ø4,0x10 mm Rubber strap Helmet retainer t. RH 1B 6.5 6. Spare parts list 6.6 Seed hopper Version NS 4000 B 6. Spare parts list Position Seed hopper Ref. Description 1 2 3 4 5 6 7 8 0602517 2152082 546208 550216 546508 544108 0602783 0602785 9 10 11 0602787 2156009 0602524 12 13 14 15 16 17 18 19 20 21 22 23 23 24 25 26 27 28 29 30 31 32 33 0603009 2155820 586216 583106 2153944 2000624 0601883 2153915 25839 32072 37178 2155841 2155839 585325 2156398 2149268 583506 582106 2152049 521206 2156329 586214 580225 Position Manometer 0-100 m. bar Bracket for manometer Face plate M8 Set screw M8 x 16 Spring washer M8 Nut M8 din 934-8 Rubber lead-in 12 x 19 Connection piece 3/8" w. 1/4" BSP Clamp 13,3 Hose for manometer Nipple pressure gauge brass 1/8" Counter nut 1/8" RG Seed hopper top Set screw M6 x 16 A.2 Washer DIN 125A-A.2 M6 Guard for seed housing Thumbscrew Flexible hose Ø63/Ø73 Nozzle for seed housing Sowing wheel Fine seed finger R-clip Sowing shaft NS4030 Sowing shaft NS4040 Split pin Ø4,0 x25 A.2 DIN94 Sowing wheel w. hexagon Ball bearing, complete Spring washer A.2 M6 Nut M6 A.2 Dazzle for dosing unit Allen screw M6x6 MSP FZB Bed plate Set screw M6x14 A.2 Set screw M6x25 A.2 Version NS 4000 B 34 35 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 63 64 66 66 66 Ref. Description 356499 2155821 2155822 0603231 0603221 2153905 2157339 585115 2153912 2153947 82340 581220 2153909 2153849 583508 0603376 582608 582110 583510 583110 552510 29370 583108 29369 36921 580255 586416 0602103 25802 28152 2156737 2156738 513730 2156736 2156741 2156152 Fixation f. rubber strap Bottom NS 4030 Bottom NS 4040 Cover plug Ø 14,7/7,2 Ferrule Ø 8x17 Bottom flap Spring Ø1,5x67 Split pin Ø2,5x16 A.2 DIN 94 Shaft for bottom flap Guard for seed housing Self-tapping screw 1/4" Carriage bolt M8 x 20 A.2 Cover plate Shutter Spring washer A.2 M8 Disc spring 16,0x8,2x0,8 A.2 Self locking nut M8 A.2 Nut M10 A.2 Spring washer A.2 M10 Washer M10 DIN 125A-A.2 Plate bolt M10 x 20 Bottom flap, stainless Washer DIN 125A-A.2 M8 Spring13,5/2/10/2076 Adjustable piece Steel bolt A.2 M6 x 55 Set screw M8 x 16 A.2 Square nut M8 A.2 Bottom flap Nylon nut Bottom flap axle NS4030 Bottom flap axle NS4040 Clamp pin Ø 6 x 30 Handle f. bottom flap Hole plate NS4030 Hole plate NS4040 6.7 6. Spare parts list 6.8 Transmission Version NS 4000 B 6. Spare parts list Position Transmission Ref. Description 1 2 3 4 5 6 7 8 8 9 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 544110 546510 546110 515125 0602261 2155480 552510 2155846 2156308 2156114 2155433 2149972 547230 546210 28083 2150457 544106 29426 513630 2155848 2149268 2155850 2155899 2155845 547325 26049 25 26 27 28 29 110210 25095 35551 2153388 2155836 Position Nut M10 din934-8 Spring washer M10 Facet washer 3/8" Locking ring Ø25 din471 Ball bearing 6005 2RS Fixture for bearing Plate bolt M10 x 20 Chain wheel z20 NS4030 Chain wheel z13 NS4040 Guard NS4030 Guard NS4040 Chain wheel 33z 08B-1 Split pin Ø3,2 x 32 din94 Face plate M10 Tension wheel 11z Pivot for tightener Nut M6 DIN 934-8 Washer Clamp pin Ø5 x 30 Chain wheel z 25 Ball bearing, complete Bearing cassette Bushing Hex22x17 L=12 Transmission sowing shaft Split pin Ø4,0 x 25 DIN 94 Washer Ø24xHEx17x1 stainless Bushing 16/22x16 - 28x4 Bearing Shaft for chain tightener Pivot for tightener Chain 08B-1 75+1 Version NS 4000 B 30 31 32 33 33 34 Ref. Description 0602373 2155835 0602374 2155834 2156328 9603605 Chain joint link straight 08B-1 Chain 08B-1 57+1+1 Chain joint link short. 08B-1 Chain 08B-1 89+1 NS4030 Chain 08B-1 86+1 NS4040 Cover plug Ø 51,5x55 6.9 6. Spare parts list 6.10 Gearbox Version NS 4000 B 6. Spare parts list Position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Gearbox Ref. Description 2153200 550255 600430 2149788 2149806 2149971 600724 515130 2149446 0602304 0602302 2153206 2153201 515140 0602308 37772 2153210 547325 25156 25095 405930 2149420 106025 2150940 513750 550220 2150415 544108 2150299 2149442 Position Vario-Exact gearbox Set screw M8X55 Copperwasher Ø 13x8x1 Lid Sealing Chain wheel 16 Z 08B-1 Clamp Ø6X36 Circlip Ø30 DIN 471 Nylon washer Ø 48x30,5x1 Sealing ring Ø 30x37x4 Ball bearing free-wheeling Chainwheel 16 Z 08B-1 Entry shaft Circlip Ø40 DIN 471 Disc spring 61,5x40,5x0,7 Chain wheel 20 Z 08B-1 Intermediate shaft Split pin Ø4X25 Selflubricating bush Bearing O-ring Ø 59,99x2,62 Bearing housing Ball bearing 6006 Cog wheel Clamp pin Ø6X50 Set screw M8X20 Gearbox housing Nut M8 Hitch pin for cassette Crossbar Version NS 4000 B Ref. Description 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 2150297 405927 2150416 2150311 2149791 548460 2149718 2150414 515135 0602309 0602303 016639 2149421 020717 2149437 0602320 552510 546510 544110 0602484 2153203 2153211 52 53 2153209 2150311 Output shaft O-ring 48,89x2,62 Bearing Driver complete Ring 48x30x8 Clamp Ø4X60 Spring Regulator shaft Locking ring Ø35 DIN 471 Disc spring 51,5x35,5x0,6 Sealing ring 22x28x4 O-ring Ø 40x3 Bearing Clamp pin Ø6X32 Regulation piece Oillevel glass M20x1,5 Carriage bolt M10X20 Spring washer M10 Nut M10 Disc spring 6,5x30,5x0,6 Intermediate piece Chain wheel w.bearing and sealing rings Input shaft mounted Driver complete 6.11 6. Spare parts list Agitator parts f.seed hopper 6.12 Version NS 4000 B 6. Spare parts list Agitator parts f.seed hopper Position Ref. Description 1 1 2 2156020 2155840 2156862 3 4 4 5 37178 2155841 2155839 26049 6 2157377 6 2157379 7 580330 8 583106 9 110210 10 25095 11 585325 12 2158382 12 2157380 13 21577376 13 2157375 14 2157383 14 2157381 Version NS 4000 B Intermediate shaft NS4030 Intermediate shaft NS4040 Double sliding socket for sowing shaft R-clip Sowing shaft NS4030 Sowing shaft NS 4040 Washer Ø24xHEX17x1 stainless Agitator shaft III NS 4030 Agitator shaft III NS 4040 Steel bolt A.2 M6x30 Washer DIN 125A -A.2 M6 Bushing 16/22x16x28x4 Bearing Split Ø 4,0x25 A.2 DIN 94 Agitator shaft II NS 4030 Agitator shaft II NS 4040 Intermediate shaft NS 4030 Intermediate shaft NS 4040 Agitator shaft I NS 4030 Agitator shaft I NS 4040 6.13 6. Spare parts list 6.14 Fan, PTO Version NS 4000 B 6. Spare parts list Fan, PTO Position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Version NS 4000 B Ref. Description 2156721 2156703 521213 106057 2156700 0602681 228113 2156705 9603558 2156724 546108 546508 550225 550320 544617 546116 546110 546510 544110 2156722 2156702 0602261 2155727 515125 2156714 2156694 544106 546506 544106 550112 2156692 2156864 2156863 Pulley with bearings Pulley Allen screw M6x13 MSP Ball bearing 6206 2 RS Bearing housing Ball bearing 6007 2 RS Nachi Key A8x7x32 Shaft M Pulley SPZ 1587 Console Fazet washer 5/16” Spring washer M8 Set screw M8 x 25 Set screw M10 x 20 Self locking nut M16 DIN985 Fazet washer 5/8” Fazet washer 3/8” Spring washer M10 Nut M10 DIN 934-8 Belt tightener, complete Pin Ball bearing 6005 2RS HICO Tension roller Cirslip Ø 25 DIN 471 Fan, mounted End piece Nut M6 DIN 934-8 Spring washer M6 Fazet washer 1/4” Set screw M6x12 Top guard Protection guard Washer 6.15 6. Spare parts list 6.16 Fan, PTO Version NS 4000 B 6. Spare parts list Fan, PTO Position Version NS 4000 B Ref. Description 1 2 0603491 0603490 3 4 603488 0602805 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 2156725 0603489 0602947 2156698 2156199 546508 550225 2152098 2152097 2155392 228116 2156699 228110 106030 2155393 546208 550230 521213 2156704 Clamp band Ø 160 mm Flex hose Ø 160 PU steel spiral Elbow 160 mm Sheet metal screw 4,8x9,5 DIN 7981 Sleeve Neck 160 mm Galvanized clamp ring Fan w. console Washer Ø 40/Ø 8 Spring washer M8 Set screw M8 x 25 Clamp band Grating Bushing f. bloweraxle Key A8x7x40 Axle Key A8x7x25 Ball bearing 6007 2RS Hub Face plate M8 Set screw M8 x 30 Allen screw M6 x 13 MSP Pulley 6.17 6. Spare parts list 6.18 Fan, hydraulic Version NS 4000 B 6. Spare parts list Fan, hydraulic Position Version NS 4000 B Ref. Description 1 2 0603491 0603490 3 4 0603488 0602805 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 2156837 0603489 0602947 2156698 2156199 546508 550225 2152098 2152097 0603267 9603540 546208 0603388 544106 2156814 550116 550325 2156810 544611 2156812 546110 546510 544110 540260 Clamp band Ø 160 mm Flex hose Ø 160 PU steel spiral Elbow 160 mm Sheet metal screw 4,8x9,5 DIN 7981 Sleeve Neck 160 mm Galvanized clamp ring Blower w. console Washer Ø 40/Ø 8 Spring washer M8 Set screw M8x25 Clamp band Grating Supporting washer 22x32x2 Gear motor 6,3 without drain Face plate M8 Allen screw M8x60 CH Nut M6 DIN 934-8 Bottom guard Set screw M6x16 Set screw M10x25 Console Self locking nut M10 DIN 985 Upper guard Fazet washer 3/8” Spring washer M10 Nut M10 DIN 934-8 Steel bolt M6x60 6.19 6. Spare parts list 6.20 Hydraulics for fan Version NS 4000 B 6. Spare parts list Hydraulics for fan Position Version NS 4000 B Ref. Description 1 2 3 4 5 406130 9603552 405830 405842 405815 6 7 8 2156826 9603553 405758 9 10 11 12 13 14 9603546 2156825 9603550 9603551 2156829 404140 15 600399 16 600400 17 18 19 20 21 405140 0602960 9603541 9603543 540445 Sealing Bonded Seal PP45-D Nipple Ø 15x1/2” Olive-ring D15-L Sleeve M15-L Screwed connection V15-L u/Md Hydraulic tube L=135 Angle adjustable Ø 15 Screwed connection GA15-LR u/Md Sowing rate adjusting valve Hydraulic tube L=108 Banjo throttle free Ø 15x1/2” Banjo Ø 15x1/2” Hydraulic hose 1/2”X2700 Quick coupling male 1/2”RG E402 Dust cap f. male 1/2” red Dust cap f. male 1/2” green Hexagon nipple 1/2”X1/2” Non-return valve CA13 Tube holder pair 22 mm Top plate Steel bolt M8x45 6.21 6. Spare parts list 6.22 Scale Version NS 4000 B 6. Spare parts list Scale Position Version NS 4000 B Ref. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 0602825 0602826 0602827 0601971 0603292 546110 546510 544110 2154999 550116 583110 552510 544108 546508 546108 2155734 550220 2155830 2155801 0603291 543920 0603290 23 24 25 26 27 28 29 30 31 32 0603296 2155172 2155803 540445 0602447 544609 544607 2154998 521206 601053 Control handle Bracket Retainer for bracket Sheet metal screw Ø6,5x20 Adjusting cable 4000 mm Facet washer 3/8" Spring washer M10 Nut M10 din934-8 Bushing Set screw M6x16 Washer M10 din125A Plate bolt M10 x 20 Nut M8 din934-8 Spring washer M8 Facet washer 5/16" Retainer for scale Set screw M8 x 20 Scale Plate for scale Counter nut MS Carriage bolt M6 x 20 Screwed connection cable ZV Distance piece Ø16x8,5x8 Thumbscrew Pointer Steel bolt M8 x 45 Washer M8 din9021A Self-locking nut M8 din985 Self-locking nut M6 din985 Clamp Allen screw M6 x 20 Control handle 6.23 6. Spare parts list 6.24 Supporting legs for tank Version NS 4000 B 6. Spare parts list Supporting legs for tank Position 1 2 3 4 5 6 7 8 9 10 11 Version NS 4000 B Ref. Description 2156013 2156680 2156012 550320 546110 544611 0603222 41384 550010 0603228 552510 Parking stand, left Frame Parking stand, right Set screw M10x20 Facet washer 3/8" Self locking nut M10 DIN 985 Transport wheel Calibration handle Set screw M5x10 Tube holder Plate bolt M10x20 6.25 6. Spare parts list 6.26 EURO coulters Version NS 4000 B 6. Spare parts list Position EURO coulters Ref. Benævnelse 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 2149928 2149964 0602430 0602431 2149320 2153948 2151790 544611 546110 2151791 540592 0602383 2150246 2151796 544609 2151806 547450 2151872 2151810 550220 0602317 540640 2150651 2151807 2151800 2151811 26 2151812 27 28 2153825 544112 Position Antilocking flap Bushing Ø 10xØ 7x22 Rivet Ø6x28 Rivet Ø7x20 Coulter point euro Collar for hose PA6 black Long coulter Self locking nut M10 DIN 985 Facet washer 3/8" Short coulter Steel bolt M10x100 Bearing 16x20x20 Inner bushing Coulter suspension I Self-locking nut M8 din985 Spring fixture I Split Ø5x50 din94 Washer 31x31/ø56 Bearing Set screw M8x20 Facet washer M12 Set screw M12x40 Clamp Spring fixture II Coulter suspension II Square tube for spring feed NS4030 Square tube for spring feed NS4040 Spring feed arm Nut M12 DIN 934-8 Version NS 4000 B 29 30 31 32 33 33 34 35 36 Ref. Description 515135 2151804 2153439 2151818 2156470 2156471 544716 540850 2156217 Locking ring Ø 35 DIN 471 Coulter suspension III Coulter pressure spindle Thread piece for spindle Coulter bar NS 4040 Coulter bar NS 4030 Counter nut M16DIN 439B Set screw M16x50 Side suspension 6.27 6. Spare parts list 6.28 Disc coulters Version NS 4000 B 6. Spare parts list Position 1 2 3 4 5 6 7 8 9 10 11 11 12 13 14 15 16 17 18 18 19 20 21 22 23 24 25 26 27 28 29 30 Disc coulters Ref. Description 0603305 2157385 0602316 106037 0602318 515040 2150859 0602939 2156303 550112 2157398 2157397 2156815 2150800 544607 544611 555108 555110 2150814 2150815 2157019 2157021 2157020 2157022 2154168 2149466 540590 546110 0602383 2151796 2150246 544609 Position Steel bolt M10 x 95 Bushing Sealing ring 6203 ZAV Ball bearing 6203 2RS Fitting washer Ø 17x24x1,0 Circlip Ø 40 DIN 972 Hub Supporting washer 17x24x1,5 Disc coulter disc Ø 319 C75 Set screw M6 x 12 Retainer f. scraper, right Retainer f. scraper, left Scraper Clamp f. scraper Self locking nut M6 DIN 985 Self locking nut M10 DIN 985 Rivet Ø 4,0 x 8 RH Rivet Ø 4,0 x 10 RH Guide plate, right Guide plate, let Coulter arm L1 - L3 Coulter arm K1 Coulter arm L2 - L4 Coulter arm K2 Retainer f. hose Bottom bellow Steel bolt M10 x 90 Fazet washer 3/8” Bearing 16x20x20 Coulter suspension I Inner bushing Self locking nut M8 DIN 985 Version NS 4000 B Ref. Description 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 2151806 547450 2151872 2151810 550220 2150651 0602317 540640 2151807 2151800 2153825 544112 0602317 515135 2153439 2151818 2151804 2151811 48 2151812 49 49 50 51 52 2156470 2156471 544716 540850 2156217 Spring holder I Klik pin Ø 5 x 50 DIN 94 Washer 31x31/Ø 56 Bearing Set screw M8 x 20 Clamp Fazet washer M12 Set screw M12 x 40 Spring holder II Coulter suspension II Feeding arm Nut M12 DIN 934-8 Fazet washer M12 Circlip Ø 35 DIN471 Coulter pressure spindle Thread piece f. spindle Coulter suspension III Square tube f. feeding NS4030 Square tube f. feeding NS4040 Coulter bar NS4040 Coulter bar NS4030 Counter nut M16 DIN 439B Set screw M16x50 Side suspension 6.29 6. Spare parts list 6.30 Plan EURO coulters Version NS 4000 B 6. Spare parts list Plan disc coulters Version NS 4000 B 6.31 6. Spare parts list 6.32 Distributor Version NS 4000 B 6. Spare parts list Distributor Position Ref. Description 1 550110 2 546206 3 2156655 4 2153995 5 * 0603248 6 2156478 6 2156479 7 8 550216 2156711 8 2154270 9 0602938 10 * 0601883 * Version NS 4000 B Set screw M6 Face plate M6 Cover plate Elbow f. distributor head Flex hose Ø 25 pu Distributor bottom, drilled 8 outlets Distributor bottom, drilled 12 outlets Set screw M8x16 Vertical tube w. return NS4030/4040 Vertical tube, short NS4040 Ferrule DPD 25 Flex hose Ø 63/73 pu plus To be ordered in meters 6.33 6. Spare parts list 6.34 Landwheel Version NS 4000 B 6. Spare parts list Position Landwheel Ref. Description 1 2 3 3 4 5 6 7 8 9 10 11 2153359 513850 2157599 2157601 0602382 2157278 2155980 513730 0603360 547325 2155908 2149286 12 13 14 15 16 17 18 18 19 20 21 22 23 24 25 26 27 28 29 0602116 550480 2156018 020721 2150489 2150754 2157600 2157602 547330 2155909 2149268 2153327 2155271 0602740 2155712 2153335 106030 2153337 540570 Position Land wheel Clamp Ø8 x 50 Axle external NS 4030 Axle external NS 4040 Klik pin tube Ø6xØ35 Axle, short Cardan joint Clamp Ø 6x30 Rubber bellow Split pin Ø4,0x25 DIN 94 Axle HEX22/Ø 16 L=120 Compression spring 5x29x400-39v Clamp Ø 6 x 40 Set screw M12 x 80 Inner tube Clamp Ø 8 x 32 External tube Stop ring Axle, long NS 4030 Axle, long NS 4040 Split pin Ø 4,0 x 30 DIN 94 Axle HEX22/Ø 16 L=83 Ball bearing, complete Chain wheel 16z 08B-1 End piece Sheet metal screw Ø4,2 x 16 Swivel arm Chain wheel 16z 08B-1 Ball bearing 6007 2RS Bearing housing Steel bolt M10 x 70 Version NS 4000 B 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Ref. Description 2155907 2155905 0602373 546210 546510 544110 544613 546212 2155765 547325 405416 513645 2155490 544712 540560 544611 Axle HEX L=148 Chain 08B-1 79+1 Straight joint link Face plate M10 Spring washer M10 Nut DIN 934-8 Self locking nut M12 DIN 985 Face plate M12 Locking plate Split pin Ø 4,0 x 25 DIN 94 Lubrication nipple M6 x 1 H1 Clamp Ø 5 x 45 Bracket for wheel arm Counter nut M12 DIN 439B Steel bolt M10 x 60 Self locking nut M10 DIN 985 6.35 6. Spare parts list 6.36 Inside marker arm Version NS 4000 B 6. Spare parts list Inside marker arm Position 1 2 3 4 5 6 7 8 9 9 10 11 12 13 14 15 16 17 18 19 Version NS 4000 B Ref. Description 20447 405416 546220 547340 2151631 2156108 513960 540275 2152350 2152351 544607 544116 2151679 550660 2156046 547440 2151455 229520 513620 2156115 Extension spring Lubricating nipple M6x1 H1 Face plate M20 Split pin Ø4,0x40 din94 Arm Lamp bracket Clamp Ø10x60 Steel bolt M6 x 75 Marker arm, right Marker arm, left Self locking nut M6 din 985 Nut M6 din 934-8 Pin Set screw M16x60 Cylinder, complete Split pin Ø5,0x40 din94 Pin for cylinder Grip pin Ø4,0 Clamp 5x20 Locking pin Ø16x93 6.37 6. Spare parts list 6.38 Outside marker arm Version NS 4000 B 6. Spare parts list Outside marker arm Position Ref. Description 1 2157785 2 2157969 3 2157784 4 9603658 5 106040 6 9603656 7 405416 8 405936 9 544116 10 2153519 11 544030 12 2149882 13 511512 14 546110 15 546510 16 544110 17 540560 18 2149155 19 38689 20 33336 21 38687 22 2149179 23 2151775 24 2149140 25 15001960 26 540590 27 2151473 28 2151476 28 2151477 29 2151690 30 546210 31 544611 32 2151249 33 2157782 34 544609 Version NS 4000 B Marker hub complete End cover Marker shaft Seal ring 25x47x9 Ball bearing 6204 Ball bearing 6303 Lubrication nipple M6x1 H1 O-ring 50,30x3,53 Nut M16 DIN 934-8 Marker disc Ø406 Carriage bolt M8x30 U-bolt Sheet metal bolt M10x35 Facet washer 3/8" Spring washer M10 Nut M10 din934-8 Steel bolt M10 x 60 Bushing Clamp Marker clamp Clamp handle M12 Marker arm NS 4030 Marker arm NS 4040 External marker arm NS 4030 Dowel with split pin Steel bolt M10x90 Bushing Ø20/11x62 Right arm NS 4040 Left arm NS 4040 Outer arm NS 4040 Face plate M10 Self locking nut M10 Adjusting bracket Marker hub Ø406 Self locking nut M8 6.39 6. Spare parts list 6.40 Hydraulic for markers Version NS 4000 B 6. Spare parts list Hydraulic for markers Position Version NS 4000 B Ref. Description 1 2 3 4 5 6 7 8 544609 546208 2154517 0602851 0602850 540455 0602823 2157604 8 2157606 9 10 405330 2157605 10 2157607 11 12 13 14 15 16 17 2152025 600958 406120 401210 405130 406130 404140 18 406140 Self-locking nut M8 din985 Face plate M8 Distance piece Nipple 13BP0608 NV 27 mm Sealing bonded seal PP45CC Steel bolt M8x55 Marker valve Hydraulic hose 1/4” L=2125 NS4040 Hydraulic hose 1/4” L=1780 NS4030 Angle nipple 05 BK 04 Hydraulic hose 1/4”L=875 NS4040 Hydraulic hose 1/4”L=220 NS4030 Hydraulic hose 1/4” L=3600 Hexagon nipple 02BP06x04 Sealing bonded seal PP45-C Valve type FT-257/5-3/8 Hexagonnipple 02BP0806 Sealing bonded seal PP45-D Quick coupling male 1/2”RG E 402 Dusp cap f. male 1/2” black 6.41 6. Spare parts list 6.42 Following harrows Version NS 4000 B 6. Spare parts list Position Ref. Description Following harrows Position 1 2 3 4 5 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Version NS 4000 B Ref. Description 2152508 2152509 544110 41714 2153136 2156717 45885 2151941 36676 540640 0602317 2153131 540694 544613 37178 43157 540570 2150768 2150769 540592 2156720 2156718 546110 544611 2150246 0602383 2152005 2154392 0603268 540755 2154360 546114 544615 Following harrow tine, right Following harrow tine, left Nut M10 DIN 934-8 Clamp Ø 35xØ 10,5x4 Litter L=2940 Litter L=4200 Harrow tine m. bue U-bolt M10 Safety split pin f. RHS 40x40 Set screw M12x40 Fazet washer M12 Following harrow bracket Steel bolt M12x130 Self locking nut M12 DIN 985 R-clip w. big eye Locking pin Steel bolt M10x70 Clamp Extension piece Steel bolt M10x100 Console, right Console, left Fazet washer 3/8” Self locking nut M10 DIN 985 Inner bushing Bearing 16x20x20 Following harrow arm Following harrow arm Top link 33,0 - 47,0 Steel bolt M14x55 Link f. following harrow Fazet washer 9/16” Self locking nut M14 DIN 985 6.43 6. Spare parts list 6.44 Foot board Version NS 4000 B 6. Spare parts list Foot board Position Ref. Description 1 2157008 2 552510 3 2156742 4 2156657 5 550425 6 546112 7 544613 8 544611 9 546110 10 2156663 11 540595 12 2156641 13 540565 14 540675 15 2154500 16 550430 17 44560500 18 226328 19 20 21 22 23 24 25 26 27 Version NS 4000 B 2156707 540645 2156713 43117 2156696 550325 2156706 550435 306150 Foot board Plate bolt M10x20 Flap f. foot board Hinge f. foot board Set screw M12x25 Fazet washer 1/2” Self locking nut M12 DIN 985 Self locking nut M10 DIN 985 Fazet washer 3/8” Bracket Steel bolt M10x130 Frame for step Steel bolt M10x65 Steel bolt M12x75 Strop Set screw M12x30 Bolt Ø 25x105 Safety split pin Ø 10 ring Ø 41 Side member, right Steel bolt M12x45 Bushing Washer Ø 35/Ø 13x4 Foot board Set screw M10x25 Side member, left Set screw M12x35 Plug 50x50x4 sort 6.45 6. Spare parts list 6.46 Supporting legs Version NS 4000 B 6. Spare parts list Supporting legs Position 1 2 3 4 5 6 7 Version NS 4000 B Ref. Description 2156006 41197 2154503 550320 0603222 544611 546110 Supporting leg, left Safety split pin f. RHS 50x50 Supporting leg Set screw M10x20 Transport wheel Self locking nut M10 DIN 985 Facet washer 3/8" 6.47 6. Spare parts list 6.48 Pre-emergence marker Version NS 4000 B 6. Spare parts list Pre-emergence marker Position Version NS 4000 B Ref. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 2153980 0602383 2153969 2153982 547330 546220 2151617 544112 546512 546112 2153984 544110 546510 546110 2153975 2153971 540594 540691 2154558 2156882 2153986 22 23 24 25 26 27 28 29 30 2153978 2148874 2156877 540540 540640 544613 2153131 540694 544611 Arm Bearing 16x20x20 Cylinder, complete Locking pin Ø 20x93 Klik pin Ø 4,0x30 DIN 94 Face plate M20 Spring 4/26/236/49,25V Nut M12 Spring washer M12 Fazet washer 1/2” Eye Nut M10 DIN 934-8 Spring washer M10 Fazet washer 3/8” Retainer Inner bushing Ø 16x3, L=90 Steel bolt M10x120 Steel bolt M12x100 Bushing Hose retainer Locking pin w. chain Ø 15x110 Bracket U-bolt M10 (50x50) Bracket Steel bolt M10x40 Set screw M12X40 Self locking nut M12 DIN 985 Following harrow bracket Steel bolt M12x130 Self locking nut M10 DIN 985 6.49 6. Hydraulic for pre-emergence marker 6.50 Version NS 4000 B 6. Hydraulic for pre-emergence marker Position Version NS 4000 B Ref. Description 1 2 3 2154390 406120 405118 4 5 6 7 8 9 0603238 600958 2153987 356330 0602132 0602131 Solenoid valve Sealing bonded seal PP45-C Hexagon nipple 3/8”x3/8” sleeve T-nipple 34BP06 Hexagon nipple 02BP06X04 Hydraulic hose 1/4” L=2500 Cable binder 5,0x400 black T-nipple 14BP04 Angle 16BP04 6.51