Transcript
Product Folder
Sample & Buy
Support & Community
Tools & Software
Technical Documents
Reference Design
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
UCC2753x 2.5-A and 5-A, 35-VMAX VDD FET and IGBT Single-Gate Driver 1 Features
3 Description
•
The UCC2753x single-channel, high-speed gate drivers can effectively drive MOSFET and IGBT power switches. Using a design that allows for a source of up to 2.5 A and 5-A sink through asymmetrical drive (split outputs), coupled with the ability to support a negative turn-off bias, rail-to-rail drive capability, extremely small propagation delay (17 ns typical), the UCC2753x devices are ideal solutions for MOSFET and IGBT power switches. The UCC2753x family of devices can also support enable, dual input, and inverting and non-inverting input functionality. The split outputs and strong asymmetrical drive boost the devices immunity against parasitic Miller turn-on effect and can help reduce ground debouncing.
1
• • • • • • • • • • • • • • • •
Low-Cost Gate Driver (Offering Optimal Solution for Driving FET and IGBTs) Superior Replacement to Discrete Transistor Pair Drive (Providing Easy Interface With Controller) TTL and CMOS Compatible Input Logic Threshold (Independent of Supply Voltage) Split Output Options Allow for Tuning of Turnon and Turnoff Currents Inverting and Noninverting Input Configurations Enable With Fixed TTL Compatible Threshold High 2.5-A Source and 2.5-A or 5-A Sink Peak Drive Currents at 18-V VDD Wide VDD Range From 10 V to 35 V Input and Enable Pins Capable of Withstanding up to –5-V DC Below Ground Output Held Low When Inputs are Floating or During VDD UVLO Fast Propagation Delays (17-ns Typical) Fast Rise and Fall Times (15-ns and 7-ns Typical With 1800-pF Load) Undervoltage Lockout (UVLO) Used as a High-Side or Low-Side Driver (If Designed With Proper BIAS and Signal Isolation) Low-Cost, Space-Saving 5-Pin or 6-Pin DBV (SOT-23) Package Options UCC27536 and UCC27537 Pin-to-Pin Compatible to TPS2828 and TPS2829 Operating Temperature Range of –40°C to 140°C
Device Information(1) PART NUMBER UCC27531
4.90 mm × 3.91 mm
SOT-23 (6)
UCC27536
SOT-23 (5)
2.90 mm × 1.60 mm
UCC27537 UCC27538
SOT-23 (6)
(1) For all available packages, see the orderable addendum at the end of the data sheet.
Driving IGBT Without Negative Bias UCC27531
EN 1
OUTH 6
IN
Switched-Mode Power Supplies DC-to-DC Converters Solar Inverters, Motor Control, UPS HEV and EV Chargers Home Appliances Renewable Energy Power Conversion SiC FET Converters
BODY SIZE (NOM)
SOIC (8)
UCC27533
2 Applications • • • • • • •
PACKAGE
+
2
OUTL 5
VDD
GND 3
+ –
4 GND Bouncing Up to -6.5 V
18 V
ISENSE
Controller
VCE(sense)
VCC + –
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA.
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
Table of Contents 1 2 3 4 5 6 7 8
Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Description (continued)......................................... Device Comparison Table..................................... Pin Configuration and Functions ......................... Specifications......................................................... 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8
9
1 1 1 2 4 4 5 6
Absolute Maximum Ratings ...................................... 6 ESD Ratings.............................................................. 6 Recommended Operating Conditions....................... 7 Thermal Information .................................................. 7 Electrical Characteristics........................................... 7 Switching Characteristics .......................................... 8 Timing Diagrams ....................................................... 9 Typical Characteristics ............................................ 10
Detailed Description ............................................ 15 9.1 Overview ................................................................. 15
9.2 Functional Block Diagrams ..................................... 16 9.3 Feature Description................................................. 18 9.4 Device Functional Modes........................................ 21
10 Applications and Implementation...................... 23 10.1 Application Information.......................................... 23 10.2 Typical Application ................................................ 24
11 Power Supply Recommendations ..................... 32 12 Layout................................................................... 32 12.1 Layout Guidelines ................................................. 32 12.2 Layout Example .................................................... 33 12.3 Thermal Consideration.......................................... 33
13 Device and Documentation Support ................. 34 13.1 13.2 13.3 13.4
Related Links ........................................................ Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................
34 34 34 34
14 Mechanical, Packaging, and Orderable Information ........................................................... 34
4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision E (July 2014) to Revision F
Page
•
Changed EN for UCC27531 From: Yes To: Yes / No in Device Comparison Table ............................................................ 4
•
Changed OUTPUT for UCC27531 From: Split To: Split / SingleDevice Comparison Table ................................................. 4
•
Added the 8-Pin SOIC package to the Pin Configuration and Functions section .................................................................. 5
•
Added UCC27531D to the Pin Functions table ..................................................................................................................... 6
•
Changed PMOS Symbol in Figure 32 ................................................................................................................................. 16
•
Changed PMOS and Logic Symbol in Figure 33 ................................................................................................................ 16
•
Changed PMOS and Logic Symbols in Figure 34................................................................................................................ 16
•
Changed PMOS and Logic Symbol in Figure 35 ................................................................................................................. 17
•
Changed PMOS Symbol in Figure 36 .................................................................................................................................. 17
•
Added Figure 37 .................................................................................................................................................................. 18
•
Changed PMOS Symbol in Figure 39 ................................................................................................................................. 20
•
Changed Enable Pin Column to Table 3 .............................................................................................................................. 21
•
Added Table 6 ..................................................................................................................................................................... 22
Changes from Revision D (April 2013) to Revision E •
Page
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Changes from Revision C (April 2013) to Revision D
Page
•
Added Startup Current UCC27537 Bias Current Parameters to the ELECTRICAL CHARACTERISTICS............................ 7
•
Added UCC27531 Start-Up Current vs. Temperature TYPICAL CHARACTERISTICS diagram. ...................................... 11
•
Added UCC27537 Start-Up Current vs. Temperature TYPICAL CHARACTERISTICS diagram. ...................................... 11
2
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
Changes from Revision B (April 2013) to Revision C •
Page
Added additional DESCRIPTION information. ..................................................................................................................... 15
Changes from Revision A (December 2012) to Revision B •
Page
Added UCC27533, UCC27536, UCC27537 and UCC27538 parts to the datasheet............................................................. 1
Changes from Original (December 2012) to Revision A •
Page
Changed Block Diagram......................................................................................................................................................... 4
Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
3
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
5 Description (continued) Leaving the input pin open holds the driver output low. The logic behavior of the driver is shown in the application diagram, timing diagram, and input and output logic truth table. Internal circuitry on VDD pin provides an undervoltage lockout function that holds output low until VDD supply voltage is within operating range. sba7
6 Device Comparison Table
4
UCC27531
UCC27533
UCC27536
UCC27537
UCC27538 2.5 A
ION PEAK
2.5 A
2.5 A
2.5 A
2.5 A
IOFF PEAK
5A
5A
2.5 A
5A
5A
PACKAGE
SOT-23-6 / SOIC-8
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-6
IN
Single
Dual
Single
Single
Dual
IN LOGIC
TTL/CMOS
TTL/CMOS
TTL/CMOS
TTL/CMOS
TTL/CMOS
EN
Yes / No
No
Yes
Yes
No
OUTPUT
Split / Single
Single
Single
Single
Split
INVERTING
No
Inverting/NonInverting
Yes
No
No
MAX VDD
35 V
35 V
35 V
35 V
35 V
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
7 Pin Configuration and Functions 5-Pin or 6-Pin SOT-23 DBV Package Top View UCC27531
UCC27533
EN
1
6 OUTH VDD
1
IN
2
5 OUTL GND
2
VDD
3
4 GND
UCC27536
5 OUT
IN+ 3
4 IN-
EN
1
GND
2
UCC27537
5 VDD
EN 1
4 OUT
5 VDD
VDD 1
6 OUTH
2
IN1
2
5 IN2
IN+ 3
4 OUT GND
3
4 OUTL
GND
IN- 3
UCC27538
8-Pin SOIC D Package Top View
Pin Functions PIN NAME
NO.
I/O
DESCRIPTION
UCC27531DBV 1
EN
I
Enable (Pull EN to GND to disable output, pull it high or leave open to enable output)
2
IN
I
Driver non-inverting input
3
VDD
I
Bias supply input
4
GND
-
Ground (all signals are referenced to this node)
5
OUTL
O
5-A sink current output of driver
6
OUTH
O
2.5-A Source Current Output of driver
1
VDD
I
Bias supply input
2
GND
-
Ground (All signals are referenced to this node)
3
IN+
I
Driver non-inverting input
4
IN-
I
Driver inverting input
5
OUT
O
2.5-A source and 5-A sink current output of driver
UCC27533DBV
UCC27536DBV 1
EN
I
Enable (pull EN to GND to disable output, pull it high or leave open to enable output)
2
GND
-
Ground (all signals are referenced to this node)
3
IN-
I
Driver inverting input
4
OUT
O
2.5-A source and 2.5-A sink current output of driver
5
VDD
I
Bias supply input
UCC27537DBV 1
EN
I
Enable (Pull EN to GND to disable Output, Pull it high or leave open to enable Output)
2
GND
-
Ground (All signals are referenced to this node)
3
IN+
I
Driver non-inverting input
4
OUT
O
2.5-A source and 5-A sink current output of driver
5
VDD
I
Bias supply input
Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
5
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
Pin Functions (continued) PIN NAME
I/O
NO.
DESCRIPTION
UCC27538DBV 1
VDD
I
Bias supply input
2
IN1
I
Driver non-inverting input
3
GND
-
Ground (all signals are referenced to this node)
4
OUTL
O
5-A sink current output of driver
5
IN2
I
Driver non-inverting input
6
OUTH
O
2.5-A source current output of driver
1
NC
-
No connection
2
IN
I
Driver non-inverting input
3
GND
-
Ground (all signals are referenced to this node)
4
NC
-
No connection
5
NC
-
No connection
6
VDD
I
Bias supply input
7
OUT
O
5-A Sink Current Output of driver and 2.5-A Source Current Output of driver
8
NC
-
No connection
UCC27531D
8 Specifications 8.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) (2) (3) MIN
MAX
UNIT
Supply voltage
VDD
–0.3
35
V
Continuous
OUTH, OUTL, OUT
–0.3
VDD +0.3
V
Pulse
OUTH, OUTL, OUT (200 ns)
–2
VDD +0.3
V
–5
27
V
–6.5
27
V
–40
150
°C
Continuous IN, EN, IN+, IN-, IN1, IN2 Pulse IN, EN, IN+, IN–, IN1, IN2 (1.5 µs) Operating virtual junction temperature, TJ Lead temperature
Soldering, 10 sec.
300
Reflow
260
Storage temperature, Tstg (1) (2) (3)
–65
150
°C °C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to GND unless otherwise noted. Currents are positive into, negative out of the specified terminal. See Thermal Information of the datasheet for thermal limitations and considerations of packages. These devices are sensitive to electrostatic discharge; follow proper device handling procedures.
8.2 ESD Ratings VALUE V(ESD) (1) (2)
6
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±4000
Charged-device model (CDM), per JEDEC specification JESD22C101 (2)
±1000
UNIT V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
8.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) Supply voltage, VDD
MIN
NOM
10
18
MAX
UNIT
32
V
–40
140
°C
Input voltage, IN, IN+, IN-, IN1, IN2
–5
25
V
Enable, EN
–5
25
V
Operating junction temperature
8.4 Thermal Information THERMAL METRIC (1)
(2)
UCC27533, UCC27536, UCC27537
UCC27531, UCC27538
UCC27531
DBV
DBV
SOIC
5 PINS
6 PINS
8 PINS
UNIT
RθJA
Junction-to-ambient thermal resistance
178.3
178.3
129.9
RθJC(top)
Junction-to-case (top) thermal resistance (3)
109.7
109.7
79.9
RθJB
Junction-to-board thermal resistance (4)
28.3
28.3
68.1
14.7
14.7
22.7
27.8
27.8
69.8
(5)
ψJT
Junction-to-top characterization parameter
ψJB
Junction-to-board characterization parameter (6)
(1) (2) (3) (4) (5) (6)
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as specified in JESD51-7, in an environment described in JESD51-2a. The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDECstandard test exists, but a close description can be found in the ANSI SEMI standard G30-88. The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB temperature, as described in JESD51-8. The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining RθJA, using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining RθJA, using a procedure described in JESD51-2a (sections 6 and 7).
8.5 Electrical Characteristics Unless otherwise noted, VDD = 18 V, TA = TJ = –40°C to 140°C, 1-µF capacitor from VDD to GND, f = 100 kHz. Currents are positive into, negative out of the specified terminal. OUTH and OUTL are tied together for UCC27531/8. Typical condition specifications are at 25°C. PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VDD = 7.0, IN, EN=VDD
100
200
300
IN, EN = GND
100
217
300
VDD = 7.0, IN+ = GND, IN- = VDD
100
200
300
IN+ = VDD, IN- = GND
100
217
300
VDD = 7.0, IN- = GND, EN = VDD
100
217
300
IN- = VDD, EN = GND
100
217
300
VDD =7.0, IN+, EN = VDD
100
200
300
IN+, EN = GND
100
217
300
VDD = 7.0, IN1, IN2=VDD
100
200
300
IN1, IN2=GND
100
200
300
8
8.9
9.8
V
7.3
8.2
9.1
V
BIAS CURRENTS IDDoff
Start-up current (UCC25731)
IDDoff
Start-up current (UCC27533)
IDDoff
Start-up current (UCC27536)
IDDoff
Start-up current (UCC27537)
IDDoff
Start-up Current (UCC27538)
μA μA μA μA μA
UNDERVOLTAGE LOCKOUT (UVLO) VON
Supply start threshold
VOFF
Minimum operating voltage after supply start
VDD_H
Supply voltage hysteresis
0.7
Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
V
7
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
Electrical Characteristics (continued) Unless otherwise noted, VDD = 18 V, TA = TJ = –40°C to 140°C, 1-µF capacitor from VDD to GND, f = 100 kHz. Currents are positive into, negative out of the specified terminal. OUTH and OUTL are tied together for UCC27531/8. Typical condition specifications are at 25°C. PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
INPUT (IN, IN+, IN1, IN2) VIN_H
Input signal high threshold, output high
Output High, IN- = LOW, EN=HIGH, IN2 or IN1 = HIGH (other is INPUT)
1.8
2
2.2
V
VIN_L
Input signal low threshold, output low
Output Low, IN- = LOW, EN=HIGH, IN2 or IN1 = HIGH (other is INPUT)
0.8
1
1.2
V
VIN_HYS
Input signal hysteresis
1
V
INPUT (IN-) VIN_H
Input signal high threshold, output low
Output low, IN+ = HIGH, EN = High
1.7
1.9
2.1
V
VIN_L
Input signal low threshold, output high
Output high,, IN+ = HIGH, EN = High
0.8
1
1.2
V
VIN_HYS
Input signal hysteresis
0.9
V
ENABLE (EN) VEN_H
Enable signal high threshold
Output High
1.7
1.9
2.1
V
VEN_L
Enable signal low threshold
Output Low
0.8
1
1.2
V
VEN_HYS
Enable signal hysteresis
0.9
V
–2.5/+5
A
OUTPUTS (OUTH/OUTL) ISRC/SNK
Source peak current (OUTH)/ sink peak current (OUTL)
CLOAD = 0.22 µF, f = 1 kHz
VOH
OUTH, high voltage
IOUTH = -10 mA
VOL
OUTL, low voltage
VOL
OUTL, Low Voltage UCC27536
ROH
OUTH, pull-up resistance
ROL
OUTL, pull-down resistance
ROL
OUTL, pull-down resistance UCC27536
VDD –0.2
VDD –0.12
VDD –0.07
V
IOUTL = 100 mA
0.065
0.125
V
IOUTL = 100 mA
0.13
0.23
V
11
12
12.5
7
12
20
TA = 25°C, IOUT = –10 mA TA = –40°C to 140°C, IOUT = –10 mA TA = 25°C, IOUT = 100 mA
0.45
0.65
0.85
TA = –40°C to 140°C, IOUT = 100 mA
0.3
0.65
1.25
TA = 25°C, IOUT = 100 mA
0.9
1.3
1.7
TA = –40°C to 140°C, IOUT = 100 mA
0.6
1.3
2.3
Ω Ω Ω
8.6 Switching Characteristics over operating free-air temperature range (unless otherwise noted) PARAMETER tR
tF
Rise time
Fall time
TEST CONDITIONS
MIN
TYP
CLOAD = 1.8 nF, See Figure 1, Figure 2, Figure 3
15
CLOAD = 1.8 nF, See Figure 1, Figure 2, Figure 3
7
MAX
UNIT ns
ns
CLOAD (UCC27536DBV) = 1.8 nF, See Figure 1, Figure 2, Figure 3
10
tD1
Turn-on propagation delay
CLOAD = 1.8 nF, IN, IN+ = 0 V to 5 V, See Figure 1, Figure 2, Figure 3
17
26
ns
tD2
Turn-off propagation delay
CLOAD = 1.8 nF, IN, IN+ = 5 V to 0 V, See Figure 1, Figure 2, Figure 3
17
26
ns
tD3
Inverting turn-off propagation delay
CLOAD = 1.8 nF, IN- = 0 V to 5 V
17
28
ns
tD4
Inverting turn-on propagation delay
CLOAD = 1.8 nF, IN- = 5 V to 0 V
20
28
ns
8
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
8.7 Timing Diagrams
Figure 1. UCC27531: (Output = OUTH Tied to OUTL) Input = IN, (EN = VDD), or Input = EN, (IN = VDD) UCC27537: (Output = OUT) Input = IN+, (EN = VDD), or Input = EN, (IN+ = VDD) UCC27538: (Output = OUTH Tied to OUTL) Input = IN1, (IN2 = VDD), or Input = IN2, (IN1 = VDD)
High INPUT (IN+ pin) Low
High IN- pin Low 90% OUTPUT 10%
tD1 t r
tD2 tf
Figure 2. UCC27533: (Output = OUT) Input = IN+ UCC27536: (Output = OUT) Input = EN High INPUT (IN- pin) Low
High Enable pin Low 90% OUTPUT 10%
tD2 tf
tD2 tr
Figure 3. UCC27533: (Output = OUT) Enable = IN+ UCC27536: (Output = OUT) Enable = EN
Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
9
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
8.8 Typical Characteristics If not specified, INPUT refers to non-inverting input 25
12
10
Fall Time (ns)
Rise Time (ns)
20
15
10
8
6
4
5
2
0
10
20
30
40
Supply Voltage (V)
0
30
CLOAD = 1.8 nF
Figure 4. Rise Time vs. Supply Voltage
Figure 5. Fall Time vs. Supply Voltage 21
Input To Output Propagation Delay (ns)
12
8
4
TurnOn
20
30
TurnOff
19
17
15
0 10
40 C002
CLOAD = 1.8 nF
16
Fall Time UCC27536 (ns)
20
Supply Voltage (V)
20
0
10
C001
0
40
10
20
Supply Voltage (V)
30
40
Supply Voltage (V)
C003
C001
CLOAD = 1.8 nF Figure 7. Propagation Delay vs. Supply Voltage
Figure 6. UCC27536 Fall Time vs. Supply Voltage 30 OUT RISING, IN- 5V to 0V OUT FALLING, IN- 0V to 5V
25
VDD = 10V VDD = 18V VDD = 32V
25
23
Supply Current (mA)
IN- Input To Output Propagation Delay (ns)
27
21
19
17
20
15
10
5
15 0
10
20
30
40
Supply Voltage (V)
0 0
100
200
300
400
500
Frequency (kHz) C001
C001
CLOAD = 1.8 nF Figure 8. IN- Propagation Delay vs. Supply
10
Submit Documentation Feedback
Figure 9. Operating Supply Current vs. Frequency
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
Typical Characteristics (continued) If not specified, INPUT refers to non-inverting input 300
300 EN=IN=Vdd
IN- = VDD, IN+ = GND
EN=IN=GND 250
250 Startup Current (µA)
UCC27533 Startup Current (µA)
IN+ = VDD, IN- = GND
200
200
150
150
100
100 -50
0
50
100
-50
150
0
50
100
C005
C002
VDD = 7 V
VDD = 7 V Figure 10. UCC27533 Start-Up Current vs. Temperature
Figure 11. UCC27531 Start-Up Current vs. Temperature
300
300 IN- = GND, EN = VDD
IN1 = IN2 = VDD
IN- = VDD, EN = GND
IN1 = IN2 = GND
250
UCC27538 Startup Current (µA)
UCC27536 Startup Current (µA)
150
Temperature ( °C)
Temperature ( °C)
200
150
100
250
200
150
100 -50
0
50
100
150
-50
0
50
Temperature ( °C)
100
150
Temperature ( °C) C004
C005
VDD = 7 V
VDD = 7 V
Figure 12. UCC27536 Start-Up Current vs. Temperature
Figure 13. UCC27538 Start-Up Current vs. Temperature 4.5
300 IN+ = EN = Vdd
4.3
4.1
Idd (mA)
UCC27537 Startup Current (µA)
IN+ = EN = GND 250
200
3.9
150 3.7
3.5
100 -50
0
50
100
150
-50
0
50
100
C006
C003
VDD = 7 V Figure 14. UCC27537 Start-Up Current vs. Temperature
Copyright © 2012–2015, Texas Instruments Incorporated
150
Temperature ( °C)
Temperature ( °C)
CLOAD = 1.8 nF
VDD = 7 V
fSW = 100 kHz
Figure 15. Operating Supply Current vs. Temperature (Output Switching)
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
11
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
Typical Characteristics (continued) If not specified, INPUT refers to non-inverting input 2.4
9.6
Turn-On
UVLO Rising UVLO Falling
2 Input Threshold (V)
9.2 Vdd UVLO Threshold (V)
Turn-Off
2.2
8.8
1.8 1.6 1.4 1.2
8.4
1 8
0.8 -50
0
50
100
-50
150
0
7HPSHUDWXUH Û&
50
100
C007
C008
Figure 16. UVLO Threshold Voltage vs. Temperature
Figure 17. Input Threshold vs. Temperature
2.4
2.4 Enable
OUT FALL 2.2
Disable
2.2
OUT RISE
2
2 Enable Threshold (V)
IN- Input Threshold (V)
150
7HPSHUDWXUH Û&
1.8
1.6
1.4
1.8 1.6 1.4
1.2
1.2
1
1
0.8
0.8 -50
0
50
100
150
-50
0
Temperature (Ü&
50
100
150
7HPSHUDWXUH Û& C002
Figure 18. In- Input Threshold vs. Temperature
C009
Figure 19. Enable Threshold vs. Temperature 1.2
25 ROH
ROL
Output Pull-Down Resistance (Ω)
Output Pull-Up Resistance (Ω)
1 20
15
10
0.8
0.6
0.4
5
0.2 -50
0
50
100
150
Temperature ( °C)
-50
0
50
100
VDD = 18 V Figure 20. Output Pullup Resistance vs. Temperature
12
Submit Documentation Feedback
150
Temperature ( °C) C010
C011
VDD = 18 V Figure 21. Output Pulldown Resistance vs. Temperature
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
Typical Characteristics (continued) If not specified, INPUT refers to non-inverting input 0.6
30 IN=HIGH
Turn-On Turn-Off
0.5
25
Propagation Delay (ns)
Operating Supply Current (mA)
IN=LOW
0.4
0.3
20
15
0.2
10 -50
0
50
100
150
-50
0
Temperature ( °C)
50
100
150
Temperature ( °C) C012
C013
VDD = 18 V
VDD = 18 V
Figure 22. Operating Supply Current vs. Temperature (Output In DC On/Off Condition)
Figure 23. Input-To-Output Propagation Delay vs. Temperature 16
30 OUT RISING, IN- 5V to 0V OUT FALLING, IN- 0V to 5V
15
Rise Time (ns)
IN- Propagation Delay (ns)
26
22
18
14
13
12
14
11
10 -50
0
50
100
-50
150
0
50
100
150
Temperature ( °C)
Temperature ( °C)
C014
C003
CLOAD = 1.8 nF
VDD = 18 V
VDD = 18 V
Figure 25. Rise Time vs. Temperature
Figure 24. IN– Input-To-Output Propagation Delay vs. Temperature 9
20
8
Fall Time UCC27536 (ns)
Fall Time (ns)
15
7
6
10
5 5
4
0 -50
0
50
100
150
-50
Temperature ( °C)
0
50
VDD = 18 V
Figure 26. Fall Time vs. Temperature
Copyright © 2012–2015, Texas Instruments Incorporated
150 C003
C015
CLOAD = 1.8 nF
100
Temperature ( °C)
CLOAD = 1.8 nF
VDD = 18 V
Figure 27. UCC27536 Fall Time vs. Temperature
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
13
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
Typical Characteristics (continued) 10
140
8
120
Rise Time (ns)
Supply Current (mA)
If not specified, INPUT refers to non-inverting input
6
4
100
80
60
2
Cload = 10nF 40
0 0
10
20
30
0
40
10
20
30
40
Supply Voltage (V)
Supply Voltage (V)
C017
C016
CLOAD = 1.8 nF
CLOAD = 1.8 nF
VDD = 18 V
Figure 29. Rise Time vs. Supply Voltage
Figure 28. Operating Supply Current vs. Supply Voltage (Output Switching) 120
70
60
Fall Time UCC27536 (ns)
100
Fall Time (ns)
50
40
30
80
60
40
20
10
20 0
10
20
30
40
Supply Voltage (V)
0
10
20
14
30
40
Supply Voltage (V) C018
C002
CLOAD = 1.8 nF
CLOAD = 1.8 nF
Figure 30. Fall Time vs. Supply Voltage
Figure 31. UCC27536 Fall Time vs. Supply Voltage
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
9 Detailed Description 9.1 Overview The UCC2753x family of devices are single-channel, high-speed, gate drivers capable of effectively driving MOSFET and IGBT power switches by up to 2.5-A source and 5-A sink (asymmetrical drive) peak current. Strong sink capability in asymmetrical drive boosts immunity against parasitic Miller turn-on effect. The UCC2753x device can also feature a split-output configuration where the gate-drive current is sourced through the OUTH pin and sunk through the OUTL pin. This pin arrangement allows the user to apply independent turnon and turn-off resistors to the OUTH and OUTL pins, respectively, and easily control the switching slew rates. The driver has rail-to-rail drive capability and extremely small propagation delay, typically 17 ns. The input threshold of UCC2753x is based on TTL and CMOS compatible low-voltage logic, which is fixed and independent of VDD supply voltage. The 1-V typical hysteresis offers excellent noise immunity. The driver has an EN pin with fixed TTL compatible threshold. EN is internally pulled up; pulling EN low disables the driver, while leaving EN open provides normal operation. The EN pin can be used as an additional input with the same performance as the IN, IN+, IN1, and IN2 pins. Table 1. UCC2753x Features and Benefits FEATURE
BENEFIT
High source and sink current capability, 2.5 A and 5 A (asymmetrical).
High current capability offers flexibility in employing UCC2753x device to drive a variety of power switching devices at varying speeds.
Low 17 ns (typ) propagation delay.
Extremely low pulse transmission distortion.
Wide VDD operating range of 10 V to 32 V.
Flexibility in system design. Can be used in split-rail systems such as driving IGBTs with both positive and negative(relative to Emitter) supplies. Optimal for many SiC FETs.
VDD UVLO protection.
Outputs are held Low in UVLO condition, which ensures predictable, glitch-free operation at power up and power down. High UVLO of 8.9 V typical ensures that power switch is not on in high-impedance state which could result in high power dissipation or even failures.
Outputs held low when input pin (INx) in floating condition.
Safety feature, especially useful in passing abnormal condition tests during safety certification
Split output structure option (OUTH, OUTL).
Allows independent optimization of turn-on and turn-off speeds using series gate resistors.
Strong sink current (5 A) and low pull-down impedance (0.65 Ω).
High immunity to high dV/dt Miller turn-on events.
CMOS and TTL compatible input threshold logic with wide hysteresis.
Enhanced noise immunity, while retaining compatibility with microcontroller logic level input signals (3.3 V, 5 V) optimized for digital power.
Input capable of withstanding –6.5 V.
Enhanced signal reliability in noisy environments that experience ground bounce on the gate driver.
Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
15
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
9.2 Functional Block Diagrams IN
VDD
2 VREF
EN
1
3
VDD
6
OUTH
5
OUTL
VDD GND
4
UVLO
EN Pull-Up Resistance to VREF = 500 kΩ, VREF = 5.8 V, IN Pull-Down Resistance to GND = 230 kΩ
Figure 32. UCC27531
IN+
VDD
3 VREF
IN-
4
1
VDD
5
OUT
VDD GND
2
UVLO
IN– Pull-Up Resistance to VREF = 500 kΩ, VREF = 5.8 V, IN+ Pull-Down Resistance to GND = 230 kΩ
Figure 33. UCC27533
EN
VDD
1 VREF
5
VDD
4
OUT
VREF IN-
3 VDD
GND
2
UVLO
EN Pull-Up Resistance to VREF = 500 kΩ, VREF = 5.8 V, IN- Pull-Up Resistance to VREF = 500 kΩ
Figure 34. UCC27536
16
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
Functional Block Diagrams (continued)
EN
VDD
1
5
VDD
4
OUT
1
VDD
6
OUTH
4
OUTL
VREF IN+
3 VDD UVLO
GND
2
EN Pull-Up Resistance to VREF = 500 kΩ, VREF = 5.8 V, IN+ Pull-Down Resistance to GND = 230 kΩ
Figure 35. UCC27537
IN1
IN2
VDD
2
5 VDD UVLO
GND
3
IN1 Pull-Down Resistance to GND = 230 kΩ, IN2 Pull-Down Resistance to GND = 230 kΩ
Figure 36. UCC27538
Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
17
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
Functional Block Diagrams (continued)
NC
VDD
1
8
NC
7
OUT
6
VDD
5
NC
VREF
IN
2
GND
3
VDD UVLO
NC
4
IN Pull-Down Resistance to GND = 230 kΩ, VREF = 5.8 V, Pull-Up Resistance to VREF = 500 kΩ
Figure 37. UCC27531D
9.3 Feature Description 9.3.1 VDD Undervoltage Lockout The UCC2753x device has internal UVLO protection feature on the VDD pin supply circuit blocks. To ensure acceptable power dissipation in the power switch, this UVLO prevents the operation of the gate driver at low supply voltages. Whenever the driver is in UVLO condition (when VDD voltage less than VON during power up and when VDD voltage is less than VOFF during power down), this circuit holds all outputs LOW, regardless of the status of the inputs. The UVLO is typically 8.9 V with 700-mV typical hysteresis. This hysteresis helps prevent chatter when low VDD supply voltages have noise from the power supply and also when there are droops in the VDD bias voltage when the system commences switching and there is a sudden increase in IDD. The capability to operate at voltage levels such as 10 V to 32 V provides flexibility to drive Si MOSFETs, IGBTs, and emerging SiC FETs.
VDD Threshold VDD
IN
OUT
Figure 38. Power Up
18
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
Feature Description (continued) 9.3.2 Input Stage The input pins of UCC2753x device are based on a TTL and CMOS compatible input threshold logic that is independent of the VDD supply voltage. With typical high threshold = 2 V and typical low threshold = 1 V, the logic level thresholds can be conveniently driven with PWM control signals derived from 3.3-V or 5-V logic. Wider hysteresis (typically 1 V) offers enhanced noise immunity compared to traditional TTL logic implementations, where the hysteresis is typically less than 0.5 V. This device also features tight control of the input pin threshold voltage levels which eases system design considerations and ensures stable operation across temperature. The very low input capacitance, typically 20 pF, on these pins reduces loading and increases switching speed. The device features an important safety function wherein, whenever the input pin is in a floating condition, the output is held in the low state. This is achieved using pull-up or pull-down resistors on the input pins as shown in the block diagrams. The input stage of the driver should preferably be driven by a signal with a short rise or fall time. Caution must be exercised whenever the driver is used with slowly varying input signals, especially in situations where the device is located in a separate daughter board or PCB layout has long input connection traces: • High dI/dt current from the driver output coupled with board layout parasitics can cause ground bounce. Because the device features just one GND pin which may be referenced to the power ground, this may interfere with the differential voltage between Input pins and GND and trigger an unintended change of output state. Because of fast 17 ns propagation delay, this can ultimately result in high-frequency oscillations, which increases power dissipation and poses risk of damage • 1-V Input threshold hysteresis boosts noise immunity compared to most other industry standard drivers. If limiting the rise or fall times to the power device to reduce EMI is necessary, then an external resistance is highly recommended between the output of the driver and the power device instead of adding delays on the input signal. This external resistor has the additional benefit of reducing part of the gate charge related power dissipation in the gate driver device package and transferring it into the external resistor itself. Finally, because of the unique input structure that allows negative voltage capability on the Input and Enable pins, caution must be used in the following applications: • Input or Enable pins are switching to amplitude > 15 V • Input or Enable pins are switched at dV/dt > 2 V/ns If both of these conditions occur, it is advised to add a series 150-Ω resistor for the pin(s) being switched to limit the current through the input structure. 9.3.3 Enable Function The Enable (EN) pin of the UCC2753x has an internal pull-up resistor to an internal reference voltage so leaving Enable floating turns on the driver and allows it to send output signals properly. If desired, the Enable can also be driven by low-voltage logic to enable and disable the driver. 9.3.4 Output Stage The output stage of the UCC2753x device is illustrated in Figure 39. The UCC2753x device features a unique architecture on the output stage which delivers the highest peak source current when it is most needed during the Miller plateau region of the power switch turn-on transition (when the power switch drain/collector voltage experiences dV/dt). The device output stage features a hybrid pull-up structure using a parallel arrangement of N-Channel and P-Channel MOSFET devices. By turning on the N-Channel MOSFET during a narrow instant when the output changes state from low to high, the gate driver device is able to deliver a brief boost in the peak sourcing current enabling fast turnon.
Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
19
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
Feature Description (continued) VDD
ROH RNMOS ,Pull Up
Anti ShootThrough Circuitry
Input Signal
OUTH OUTL Narrow Pulse at each Turn On ROL
Figure 39. UCC27531 Gate Driver Output Stage Split output depicted in Figure 39. For devices with single OUT pin, OUTH and OUTL are connected internally and then connected to OUT. The ROH parameter (see Electrical Table) is a DC measurement and it is representative of the on-resistance of the P-Channel device only, because the N-Channel device is turned on only during output change of state from low to high. Thus the effective resistance of the hybrid pull-up stage is much lower than what is represented by ROH parameter. The pull-down structure is composed of a N-channel MOSFET only. The ROL parameter (see Electrical Characteristics), which is also a DC measurement, is representative of true impedance of the pull-down stage in the device. In UCC2753x, the effective resistance of the hybrid pull-up structure is approximately 3 x ROL. The UCC2753x can deliver 2.5-A source, and up to 5-A sink at VDD = 18 V. Strong sink capability results in a very low pull-down impedance in the driver output stage which boosts immunity against the parasitic Miller turnon (high slew rate dV/dt turnon) effect that is seen in both IGBT and FET power switches . An example of a situation where Miller turnon is a concern is synchronous rectification (SR). In SR application, the dV/dt occurs on MOSFET drain when the MOSFET is already held in OFF state by the gate driver. The current charging the CGD Miller capacitance during this high dV/dt is shunted by the pull-down stage of the driver. If the pull-down impedance is not low enough then a voltage spike can result in the VGS of the MOSFET, which can result in spurious turnon. This phenomenon is illustrated in Figure 40. VDS
VIN
Miller Turn -On Spike in V GS
C GD
Gate Driver RG
COSS
ISNK CGS
ROL
VTH
VGS of MOSFET ON OFF
VIN
VDS of MOSFET
Figure 40. Low Pull-Down Impedance in UCC2753x (Output Stage Mitigates Miller Turn-On Effect) 20
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
Feature Description (continued) The driver output voltage swings between VDD and GND providing rail-to-rail operation because of the low dropout of the output stage. In many cases, the external Schottky diode clamps may be eliminated because the presence of the MOSFET body diodes offers low impedance to switching overshoots and undershoots.
9.4 Device Functional Modes The UCC2753x devices operate in normal mode and UVLO mode (see VDD Undervoltage Lockout section for information on UVLO operation). In normal mode, the output state is dependent on the states of the device, and the input pins. The UCC27531 features a single, non-inverting input, but also contains enable and disable functionality through the EN pin. Setting the EN pin to logic HIGH will enable the non-inverting input to output on the IN pin. The device uses a split output (OUTH, and OUTL) to allow for separate sourcing and sinking pins, which can help reduce ground de-bouncing. The UCC27533 features a dual input. One inverting (IN+), and one non-inverting (IN–). This device does not contain an enable feature, and has a single output. The UCC27536 is similar to the UCC27531, but uses an inverting input, and a single output. The UCC27537 is also similar to the UCC27531, but uses a single output. The UCC27538 is again similar to the UCC27531, but features dual inputs IN1 and IN2, rather than an enable and disable feature. The UCC27531D features a single input and a single output. The device is always enabled. See Table 2, Table 4, and Table 5 for lists of the output states of the different devices and their inputs: Table 2. Input/Output Logic Truth Table (For Single Output Driver) EN PIN
OUTH PIN
OUTL PIN
OUT (OUTH and OUTL pins tied together)
L
L
High-Impedance
L
L
L
H
High-Impedance
L
L
H
L
High-Impedance
L
L
H
H
H
High-Impedance
H
H
FLOAT
H
High-Impedance
H
FLOAT
H
High-Impedance
L
L
IN PIN UCC27531DBV
Table 3. Input/Output Logic Truth Table (For Single Output Driver with Enable Pin) EN PIN
IN- / IN+ PIN
OUT PIN
L
L
L
L
H
L
H
L
H
H
H
L
H
X
L
L
L
L
UCC27536DBV
UCC27537DBV L
H
L
H
L
L
H
H
L
H
X
H
Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
21
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
Table 4. Input/Output Logic Truth Table IN+ PIN
IN- PIN
OUT PIN
L
L
L
L
H
L
H
L
H
H
H
L
FLOAT
X
L
X
FLOAT
L
UCC27533DBV
Table 5. Input/Output Logic Truth Table (For Single Output Driver) IN2 PIN
OUTH PIN
OUTL PIN
OUT (OUTH and OUTL pins tied together)
L
L
High-Impedance
L
L L
IN1 PIN UCC27538DBV L
H
High-Impedance
L
H
L
High-Impedance
L
L
H
H
H
High-Impedance
H
X
FLOAT
High-Impedance
L
L
FLOAT
X
High-Impedance
L
L
Table 6. Input/Output Logic Truth Table (For Single Input/Output Driver) IN PIN
OUT PIN
L
L
H
H
FLOAT
L
UCC27531D
22
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
10 Applications and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality.
10.1 Application Information High-current gate driver devices are required in switching power applications for a variety of reasons. To enable fast switching of power devices and reduce associated switching power losses, a powerful gate driver can be employed between the PWM output of controllers or signal isolation devices and the gates of the power semiconductor devices. Further, gate drivers are indispensable when sometimes it is just not feasible to have the PWM controller directly drive the gates of the switching devices. The situation will be often encountered because the PWM signal from a digital controller or signal isolation device is often a 3.3-V or 5-V logic signal which is not capable of effectively turning on a power switch. A level-shifting circuitry is needed to boost the logic-level signal to the gate-drive voltage in order to fully turn on the power device and minimize conduction losses. Traditional buffer drive circuits based on NPN/PNP bipolar, (or P- N-channel MOSFET), transistors in totem-pole arrangement, being emitter follower configurations, prove inadequate for this because they lack level-shifting capability and low-drive voltage protection. Gate drivers effectively combine both the level-shifting, buffer drive and UVLO functions. Gate drivers also find other needs such as minimizing the effect of switching noise by locating the high-current driver physically close to the power switch, driving gate-drive transformers and controlling floating power device gates, reducing power dissipation and thermal stress in controllers by moving gate charge power losses into itself. The UCC2753x is very flexible in this role with a strong current drive capability and wide supply voltage range up to 32 V. This allows the driver to be used in 12-V Si MOSFET applications, 20-V and -5-V (relative to Source) SiC FET applications, 15-V and -15-V (relative to Emitter) IGBT applications and many others. As a singlechannel driver, the UCC2753x can be used as a low-side or high-side driver. To use as a low-side driver, the switch ground is usually the system ground so it can be connected directly to the gate driver. To use as a highside driver with a floating return node however, signal isolation is needed from the controller as well as an isolated bias to the UCC2753x. Alternatively, in a high-side drive configuration the UCC2753x can be tied directly to the controller signal and biased with a nonisolated supply. However, in this configuration the outputs of the UCC2753x must drive a pulse transformer which then drives the power-switch to work properly with the floating source and emitter of the power switch. Further, having the ability to control turn-on and turn-off speeds independently with both the OUTH and OUTL pins ensures optimum efficiency while maintaining system reliability. These requirements coupled with the need for low propagation delays and availability in compact, lowinductance packages with good thermal capability makes gate driver devices such as the UCC2753x extremely important components in switching power combining benefits of high-performance, low cost, component count and board space reduction and simplified system design.
Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
23
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
10.2 Typical Application 10.2.1 Driving IGBT Without Negative Bias
UCC27531
EN
OUTH
1
6
IN
OUTL
+
2
5
VDD
GND 3
+ –
4 GND Bouncing Up to -6.5 V
18 V
ISENSE
Controller
VCE(sense)
VCC + –
Figure 41. Driving IGBT Without Negative Bias 10.2.1.1 Design Requirements When selecting the proper gate driver device for an end application, some design considerations must be evaluated first in order to make the most appropriate selection. The following design parameters should be used when selecting the proper gate driver device for an end application: input-to-output configuration, the input threshold type, bias supply voltage levels, peak source and sink currents, availability of independent enable and disable functions, propagation delay, power dissipation, and package type. See the example design parameters and requirements in Table 7. Table 7. Design Parameters DESIGN PARAMETER
EXAMPLE VALUE
IN-OUT configuration
Noninverting
Input threshold type
CMOS
Bias supply voltage levels
+18 V
Negative output low voltage
N/A
dVDS/dt
(1)
24
(1)
20 V/ns
Enable function
Yes
Disable function
N/A
Propagation delay
<30 ns
Power dissipation
<0.25 W
Package type
DBV
dVDS/dt is a typical requirement for a given design. This value can be used to find the peak source/sink currents needed as shown in Peak Source and Sink Currents.
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
10.2.1.2 Detailed Design Procedure 10.2.1.2.1 Input-to-Output Configuration
The design should specify which type of input-to-output configuration should be used. If turning on the power MOSFET or IGBT when the input signal is in high state is preferred, then a device capable of the non-inverting configuration must be selected. If turning off the power MOSFET or IGBT when the input signal is in high state is preferred, then a device capable of the inverting configuration must be chosen. If ground-debouncing is a potential issue, a split output device should be chosen (UCC27531, or UCC27538). On these devices, OUTH sources current to charge the MOSFET or IGBT gate when transitioning from an output LOW to HIGH, and OUTL sinks current to discharge the MOSFET or IGBT gate when transitioning from an output HIGH to LOW. If dual inputs are required, the chosen device should be either the UCC27533, or the UCC27538. Based on these requirements, the proper device out of the UCC27531, UCC27533, UCC27536, UCC27537, or UCC27538 should be selected. See the Device Functional Modes section for information on individual device functionality and the Device Comparison Table table. 10.2.1.2.2 Input Threshold Type
The type of Input voltage threshold determines the type of controller that can be used with the gate driver device. The UCC2753x devices feature a TTL and CMOS-compatible input threshold logic, with wide hysteresis. The threshold voltage levels are low voltage and independent of the VDD supply voltage, which allows compatibility with both logic-level input signals from microcontrollers as well as higher-voltage input signals from analog controllers. See the Electrical Characteristics table for the actual input threshold voltage levels and hysteresis specifications for the UCC2753x devices. 10.2.1.2.3 VDD Bias Supply Voltage
The bias supply voltage to be applied to the VDD pin of the device should never exceed the values listed in the Recommended Operating Conditions table. However, different power switches demand different voltage levels to be applied at the gate terminals for effective turnon and turnoff. With certain power switches, a positive gate voltage may be required for turnon and a negative gate voltage may be required for turnoff, in which case the VDD bias supply equals the voltage differential. With an operating range from 10 V to 32 V, the UCC2753x devices can be used to drive a power switches such as power MOSFETS and IGBTs (VGE = 15 V, 18 V). 10.2.1.2.4 Peak Source and Sink Currents
Generally, the switching speed of the power switch during turnon and turnoff should be as fast as possible to minimize switching power losses. The gate driver device must be able to provide the required peak current for achieving the targeted switching speeds for the targeted power MOSFET. Using the example of a power MOSFET, the system requirement for the switching speed is typically described in terms of the slew rate of the drain-to-source voltage of the power MOSFET (such as dVDS/dt). For example, the system requirement might state that a SPP20N60C3 power MOSFET must be turned on with a dVDS/dt of 20 V/ns or higher under a DC bus voltage of 400 V in a continuous-conduction-mode (CCM) boost PFC-converter application. This type of application is an inductive hard-switching application and reducing switching power losses is critical. This requirement means that the entire drain-to-source voltage swing during power MOSFET turn-on event (from 400 V in the OFF state to VDS(on) in on state) must be completed in approximately 20 ns or less. When the drain-to-source voltage swing occurs, the Miller charge of the power MOSFET (QGD parameter in SPP20N60C3 power MOSFET data sheet = 33 nC typical) is supplied by the peak current of gate driver. According to power MOSFET inductive switching mechanism, the gate-to-source voltage of the power MOSFET at this time is the Miller plateau voltage, which is typically a few volts higher than the threshold voltage of the power MOSFET, VGS(TH). To achieve the targeted dVDS/dt, the gate driver must be capable of providing the QGD charge in 20 ns or less. In other words a peak current of 1.65 A (= 33 nC / 20 ns) or higher must be provided by the gate driver. The UCC2753x series of gate drivers can provide 2.5-A peak sourcing current, and 5A peak sinking current which clearly exceeds the design requirement and has the capability to meet the switching speed needed. The 1.5x sourcing, and 3x sinking overdrive capability provides an extra margin against part-to-part variations in the QGD parameter of the power MOSFET along with additional flexibility to insert external gate resistors and fine tune the switching speed for efficiency versus EMI optimizations. However, in practical designs the parasitic trace Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
25
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
inductance in the gate drive circuit of the PCB will have a definitive role to play on the power MOSFET switching speed. The effect of this trace inductance is to limit the dI/dt of the output current pulse of the gate driver. To illustrate this, consider output current pulse waveform from the gate driver to be approximated to a triangular profile, where the area under the triangle (½ ×IPEAK × time) would equal the total gate charge of the power MOSFET (QG parameter in SPP20N60C3 power MOSFET datasheet = 87 nC typical). If the parasitic trace inductance limits the dI/dt then a situation may occur in which the full peak current capability of the gate driver is not fully achieved in the time required to deliver the QG required for the power MOSFET switching. In other words, the time parameter in the equation would dominate and the IPEAK value of the current pulse would be much less than the true peak current capability of the device, while the required QG is still delivered. Because of this, the desired switching speed may not be realized, even when theoretical calculations indicate the gate driver can achieve the targeted switching speed. Thus, placing the gate driver device very close to the power MOSFET and designing a tight gate drive-loop with minimal PCB trace inductance is important to realize the full peakcurrent capability of the gate driver. 10.2.1.2.5 Enable and Disable Function
Certain applications demand independent control of the output state of the driver without involving the input signal. A pin which offers an enable and disable function achieves this requirement. For these applications, the UCC27531, UCC27536, or UCC27537 are suitable as they feature an input pin (IN– for UCC27536) and an Enable pin. Other applications require multiple inputs. Under those requirements, the UCC27533 or UCC27538 are suitable. The UCC27533 features an IN+ and IN– pin, both of which control the state of the output as listed in Table 3. Based on whether an inverting or non-inverting input signal is provided to the driver, the appropriate input pin can be selected as the primary input for controlling the gate driver. The other unused input pin can be conveniently used for the enable and disable functionality if needed. If the design does not require an enable function, the unused input pin can be tied to either the VDD pin (in case IN+ is the unused pin), or GND (in case IN– is unused pin) in order to ensure it does not affect the output status. The UCC27538 features two independent inputs IN1 and IN2. These contain the same functionality as the UCC27533, but instead both of these IN1 and IN2 pins are non-inverting. 10.2.1.2.6 Propagation Delay
The acceptable propagation delay from the gate driver is dependent on the switching frequency at which it is used and the acceptable level of pulse distortion to the system. The UCC27516 and UCC27517 devices feature 17-ns (typical) (20-ns for inverting turn-on) propagation delays which ensures very little pulse distortion and allows operation at very higher frequencies. See Switching Characteristics for the propagation and switching characteristics of the UCC2753x devices. 10.2.1.2.7 Power Dissipation
Power dissipation of the gate driver has two portions as shown in equation below: PDISS = PDC + PSW
(1)
The DC portion of the power dissipation is PDC = IQ x VDD where IQ is the quiescent current for the driver. The quiescent current is the current consumed by the device to bias all internal circuits such as input stage, reference voltage, logic circuits, protections etc and also any current associated with switching of internal devices when the driver output changes state (such as charging and discharging of parasitic capacitances, parasitic shootthrough). The UCC2753x features very low quiescent currents (less than 1 mA) and contains internal logic to eliminate any shoot-through in the output driver stage. Thus the effect of the PDC on the total power dissipation within the gate driver can be safely assumed to be negligible. In practice this is the power consumed by driver when its output is disconnected from the gate of power switch. The power dissipated in the gate driver package during switching (PSW) depends on the following factors: • Gate charge required of the power device (usually a function of the drive voltage VG, which is very close to input bias supply voltage VDD due to low VOH drop-out) • Switching frequency • Use of external gate resistors When a driver device is tested with a discrete, capacitive load it is a fairly simple matter to calculate the power that is required from the bias supply. The energy that must be transferred from the bias supply to charge the capacitor is given by: 26
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
EG =
1 CLOAD VDD2 2
where •
CLOAD is load capacitor and VDD is bias voltage feeding the driver.
(2)
There is an equal amount of energy dissipated when the capacitor is discharged. During turnoff the energy stored in capacitor is fully dissipated in drive circuit. This leads to a total power loss during switching cycle given by the following: PG = CLOAD VDD2 fsw
where •
ƒSW is the switching frequency
(3)
The switching load presented by a power FET and IGBT can be converted to an equivalent capacitance by examining the gate charge required to switch the device. This gate charge includes the effects of the input capacitance plus the added charge needed to swing the drain voltage of the power device as it switches between the ON and OFF states. Most manufacturers provide specifications of typical and maximum gate charge, in nC, to switch the device under specified conditions. Using the gate charge Qg, one can determine the power that must be dissipated when charging a capacitor. This is done by using the equivalence, Qg = CLOADVDD, to provide the following equation for power: PG = CLOAD VDD2 fsw = Qg VDD fsw
(4)
This power PG is dissipated in the resistive elements of the circuit when the MOSFET and IGBT is being turned on or off. Half of the total power is dissipated when the load capacitor is charged during turn-on, and the other half is dissipated when the load capacitor is discharged during turn-off. When no external gate resistor is employed between the driver and MOSFET and IGBT, this power is completely dissipated inside the driver package. With the use of external gate drive resistors, the power dissipation is shared between the internal resistance of driver and external gate resistor in accordance to the ratio of the resistances (more power dissipated in the higher resistance component). Based on this simplified analysis, the driver power dissipation during switching is calculated as follows:
æ ö ROFF RON PSW = 0.5 ´ Qg ´ VDD ´ fsw ç + ÷ ç (ROFF + RGATE ) (RON + RGATE ) ÷ è ø where •
ROFF = ROL and RON (effective resistance of pull-up structure) = 3 x ROL
Copyright © 2012–2015, Texas Instruments Incorporated
(5)
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
27
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
10.2.1.3 Application Curve The following application curves were observed using the UCC27531 on the UCC27531EVM-184. NOTE Legend: Green: EVM PWM Input, Blue: UCC27531 IN, Red: EVM GATE Output
Figure 42. UCC27531DBV Input vs. Output PWM Propagation Delay (High)
Figure 43. UCC27531DBV Input vs. Output PWM Propagation Delay (Low)
Figure 44. UCC27531DBV Input vs. Output PWM Rise Time
28
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
10.2.2 Driving IGBT With 13-V Negative Turn-Off BIAS UCC27531 EN
OUTH 1
IN
6 OUTL
+ 2
5
3
4
VDD + –
GND
18 V
+ –
13 V
Figure 45. Driving IGBT With 13-V Negative Turn-Off BIAS 10.2.2.1 Design Requirements Refer to the previous Design Requirements section. 10.2.2.2 Detailed Design Procedure Refer to the previous Detailed Design Procedure section. 10.2.2.3 Application Curve Refer to the previous Application Curve section.
Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
29
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
10.2.3 Single-Output Driver
UCC27533 IN4
OUT 5
IN+
+ 3
VDD
GND 1
+ –
2
18 V
+ –
13 V
Figure 46. Single-Output Driver 10.2.3.1 Design Requirements Refer to the previous Design Requirements section. 10.2.3.2 Detailed Design Procedure Refer to the previous Detailed Design Procedure section. 10.2.3.3 Application Curve Refer to the previous Application Curve section.
30
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
10.2.4 Using UCC2753x Drivers in an Inverter E/2
+ – Isol. UCC2753x
Isol. UCC2753x
Controller
Isol. UCC2753x
Isol. UCC2753x E/2
+ –
Figure 47. Using UCC2753x Drivers in an Inverter 10.2.4.1 Design Requirements Refer to the previous Design Requirements section. 10.2.4.2 Detailed Design Procedure Refer to the previous Detailed Design Procedure section. 10.2.4.3 Application Curve Refer to the previous Application Curve section.
Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
31
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
11 Power Supply Recommendations The bias supply voltage range for which the UCC2753x devices are rated to operate is from 10 V to 32 V. The lower end of this range is governed by the internal UVLO protection feature on the VDD pin supply circuit blocks. Whenever the driver is in UVLO condition when the VDD pin voltage is below the V(ON) supply start threshold, this feature holds the output low, regardless of the status of the inputs. The upper end of this range is driven by the 35-V absolute maximum voltage rating of the VDD pin of the device (which is a stress rating). Keeping a 3-V margin to allow for transient voltage spikes, the maximum recommended voltage for the VDD pin is 32 V. The UVLO protection feature also involves a hysteresis function. This means that when the VDD pin bias voltage has exceeded the threshold voltage and device begins to operate, and if the voltage drops, then the device continues to deliver normal functionality unless the voltage drop exceeds the hysteresis specification VDD(hys). Therefore, ensuring that, while operating at or near the 9.8 V range, the voltage ripple on the auxiliary power supply output is smaller than the hysteresis specification of the device is important to avoid triggering device shutdown. During system shutdown, the device operation continues until the VDD pin voltage has dropped below the V(OFF) threshold which must be accounted for while evaluating system shutdown timing design requirements. Likewise, at system start-up, the device does not begin operation until the VDD pin voltage has exceeded above the V(ON) threshold. The quiescent current consumed by the internal circuit blocks of the device is supplied through the VDD pin. Although this fact is well known, recognizing that the charge for source current pulses delivered by the OUT pin is also supplied through the same VDD pin is important. As a result, every time a current is sourced out of the output pin (OUT), a corresponding current pulse is delivered into the device through the VDD pin. Thus ensuring that local bypass capacitors are provided between the VDD and GND pins and located as close to the device as possible for the purpose of decoupling is important. A low-ESR, ceramic surface-mount capacitor is mandatory.
12 Layout 12.1 Layout Guidelines Proper PCB layout is extremely important in a high-current, fast-switching circuit to provide appropriate device operation and design robustness. The UCC2753x gate driver incorporates short propagation delays and powerful output stages capable of delivering large current peaks with very fast rise and fall times at the gate of power switch to facilitate voltage transitions very quickly. At higher VDD voltages, the peak current capability is even higher (2.5-A and 5-A peak current is at VDD = 18 V). Very high di/dt can cause unacceptable ringing if the trace lengths and impedances are not well controlled. The following circuit layout guidelines are strongly recommended when designing with these high-speed drivers. • Locate the driver device as close as possible to power device to minimize the length of high-current traces between the driver output pins and the gate of the power switch device. • Locate the VDD bypass capacitors between VDD and GND as close as possible to the driver with minimal trace length to improve the noise filtering. These capacitors support high peak current being drawn from VDD during turn-on of power switch. The use of low inductance SMD components such as chip resistors and chip capacitors is highly recommended. • The turn-on and turn-off current loop paths (driver device, power switch and VDD bypass capacitor) should be minimized as much as possible in order to keep the stray inductance to a minimum. High di/dt is established in these loops at two instances – during turn-on and turn-off transients, which induces significant voltage transients on the output pins of the driver device and gate of the power switch. • Wherever possible, parallel the source and return traces of a current loop, taking advantage of flux cancellation • Separate power traces and signal traces, such as output and input signals. • Star-point grounding is a good way to minimize noise coupling from one current loop to another. The GND of the driver should be connected to the other circuit nodes such as source of power switch, ground of PWM controller, and so forth, at a single point. The connected paths should be as short as possible to reduce inductance and be as wide as possible to reduce resistance. • Use a ground plane to provide noise shielding. Fast rise and fall times at OUT may corrupt the input signals during transition. The ground plane must not be a conduction path for any current loop. Instead the ground plane must be connected to the star-point with one trace to establish the ground potential. In addition to noise 32
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 www.ti.com
SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
Layout Guidelines (continued) shielding, the ground plane can help in power dissipation as well.
12.2 Layout Example
Figure 48. Layout Example: UCC27531DBV
12.3 Thermal Consideration The useful range of a driver is greatly affected by the drive power requirements of the load and the thermal characteristics of the package. In order for a gate driver to be useful over a particular temperature range the package must allow for the efficient removal of the heat produced while keeping the junction temperature within rated limits. The thermal metrics for the driver package is summarized in the Thermal Information section of the datasheet. For detailed information regarding the thermal information table, refer to Application Note from Texas Instruments entitled IC Package Thermal Metrics (SPRA953).
Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
33
UCC27531, UCC27533, UCC27536, UCC27537, UCC27538 SLUSBA7F – DECEMBER 2012 – REVISED JULY 2015
www.ti.com
13 Device and Documentation Support 13.1 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 8. Related Links PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL DOCUMENTS
TOOLS & SOFTWARE
SUPPORT & COMMUNITY
UCC27531
Click here
Click here
Click here
Click here
Click here
UCC27533
Click here
Click here
Click here
Click here
Click here
UCC27536
Click here
Click here
Click here
Click here
Click here
UCC27537
Click here
Click here
Click here
Click here
Click here
UCC27538
Click here
Click here
Click here
Click here
Click here
13.2 Trademarks All trademarks are the property of their respective owners.
13.3 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.
13.4 Glossary SLYZ022 — TI Glossary. This glossary lists and explains terms, acronyms, and definitions.
14 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
34
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: UCC27531 UCC27533 UCC27536 UCC27537 UCC27538
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jul-2015
PACKAGING INFORMATION Orderable Device
Status (1)
Package Type Package Pins Package Drawing Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking (4/5)
UCC27531D
PREVIEW
SOIC
D
8
75
TBD
Call TI
Call TI
-40 to 125
27531D
UCC27531DBVR
ACTIVE
SOT-23
DBV
6
3000
Green (RoHS & no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 140
7531
UCC27531DBVT
ACTIVE
SOT-23
DBV
6
250
Green (RoHS & no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 140
7531
UCC27531DR
PREVIEW
SOIC
D
8
2500
TBD
Call TI
Call TI
-40 to 125
27531D
UCC27533DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS & no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 140
7533
UCC27533DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS & no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 140
7533
UCC27536DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS & no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 140
7536
UCC27536DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS & no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 140
7536
UCC27537DBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS & no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 140
7537
UCC27537DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS & no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 140
7537
UCC27538DBVR
ACTIVE
SOT-23
DBV
6
3000
Green (RoHS & no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 140
7538
UCC27538DBVT
ACTIVE
SOT-23
DBV
6
250
Green (RoHS & no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 140
7538
(1)
The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jul-2015
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF UCC27531 :
• Automotive: UCC27531-Q1 NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION www.ti.com
9-Jul-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins Type Drawing
SPQ
Reel Reel A0 Diameter Width (mm) (mm) W1 (mm)
UCC27531DBVR
SOT-23
DBV
6
3000
179.0
8.4
B0 (mm)
K0 (mm)
P1 (mm)
W Pin1 (mm) Quadrant
3.2
3.2
1.4
4.0
8.0
Q3
UCC27531DBVT
SOT-23
DBV
6
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
UCC27533DBVR
SOT-23
DBV
5
3000
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
UCC27533DBVT
SOT-23
DBV
5
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
UCC27536DBVR
SOT-23
DBV
5
3000
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
UCC27536DBVT
SOT-23
DBV
5
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
UCC27537DBVR
SOT-23
DBV
5
3000
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
UCC27537DBVT
SOT-23
DBV
5
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
UCC27538DBVR
SOT-23
DBV
6
3000
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
UCC27538DBVT
SOT-23
DBV
6
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION www.ti.com
9-Jul-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
UCC27531DBVR
SOT-23
DBV
6
3000
203.0
203.0
35.0
UCC27531DBVT
SOT-23
DBV
6
250
203.0
203.0
35.0
UCC27533DBVR
SOT-23
DBV
5
3000
203.0
203.0
35.0
UCC27533DBVT
SOT-23
DBV
5
250
203.0
203.0
35.0
UCC27536DBVR
SOT-23
DBV
5
3000
203.0
203.0
35.0
UCC27536DBVT
SOT-23
DBV
5
250
203.0
203.0
35.0
UCC27537DBVR
SOT-23
DBV
5
3000
203.0
203.0
35.0
UCC27537DBVT
SOT-23
DBV
5
250
203.0
203.0
35.0
UCC27538DBVR
SOT-23
DBV
6
3000
203.0
203.0
35.0
UCC27538DBVT
SOT-23
DBV
6
250
203.0
203.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated
Mouser Electronics Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments: UCC27531DBVR UCC27531DBVT UCC27531D UCC27531DR
