Transcript
Installation Guide
NXA-TTS43X-BL Table-Top Stand for NXD-430/435 1.
Overview The NXA-TTS43X-BL Table Top Stand (FG2262-40) for the NXD-430 and NXD-435 4.3" Modero® Wall/Flush Mount Touch Panels (panel not included) provides a table top installation option for conference rooms and residential applications (FIG. 1). NXA-TTS43X-BL Bezel
NXD-43X Faceplate
Gently lift up on the Bezel from the top edge to disengage the plastic tabs on the top edge of the panel from the notches on the Bezel. Note: Be careful not to damage the button cable that connects the NXD-43X panel to the Bezel (see FIG. 2). 2. Disconnect the button connector cable from the Bezel. 3. Remove the Bezel from the two bottom prongs.
Step 3: Remove the NXD-43X Back Box To remove the plastic back-box from the NXD-43X: 1. Remove the two plastite mounting screws from the bottom front of the touch panel (FIG. 3). These screws secure the panel to the back-box.
NXD-43X Touch Panel NXD-43X panel
NXA-TTS43X-BL Enclosure FIG. 1 NXA-TTS43X-BL with NXD-430 touch panel installed (Touch Panel not included)
NXD-43X back-box
NXA-TTS43X-BL Specifications Compatible With:
NXD-430 (FG2262-02) and NXD-435 (FG2262-04) 4.3" Modero® Wall/Flush Mount Touch Panels The NXD-43X Touch Panel is sold separately. Note: The NXA-TTS43X-BL Table-Top Stand is designed specifically for use only with the NXD-430and NXD-435. Do not mount any other device in the NXA-TTS43X-BL.
Enclosure:
Metal with matte black finish
Dimensions (HWD):
• Decimal inches: 3.790” x 7.0” x 5.255” • Fraction Inches: 3 13/16” x 7” x 5 1/4” • Metrics: 9.63cm x 17.78cm x 13.35cm
mounting screws FIG. 3 Removing mounting screws from the bottom front of the touch panel Note: Discard these plastite screws; they should not be re-used. 2. Remove the touch panel from the back-box (FIG. 4): Tab Tab
Weight:
1.2 lbs. (0.54 kg)
Included Accessories:
• Strain Relief Bracket (62-1800-06) • Strain Relief (45-0004-04) • (2) Mounting Screws, #4-40 x .250 LG, PPH, Zinc (80-0110)
NXD-43X panel NXD-43X back-box
Installation The following sections describe each step required to install an NXD-43X Touch Panel into the NXA-TTS43X-BL Table-Top Stand. This procedure involves first removing the NXD-43X from it’s back-box, then installing the NXD-43X panel into the NXA-TTS43X-BL Table-Top Stand. Note: Before touching the device, discharge the static electricity from your body by touching a grounded metal object.
Step 1: Disconnect Touch Panel Wiring If the panel is connected, disconnect all wiring from the NXD-43X: • Ethernet Port - The NXD-43X has no power input port. Instead, all power is supplied via the Power over Ethernet (PoE) protocol. With PoE, the power is supplied directly through the Ethernet port from either a PoE-enabled switcher, or through a PoE Injector (such as the PS-POE-AF). • Mini-USB Port - The mini-USB port is used solely for software upload.
Step 2: Remove the Bezel from the NXD-43X
FIG. 4 Removing the NXD-43X Back Box a. b.
Gently pull the panel from the bottom edge. Note that the top edge is secured to the back-box with two metal tabs. Disengage the metal tabs on the top of the panel from the notches on the back-box.
Step 4: Establish Internal Connections The NXA-TTS43X-BL Table-Top Stand is equipped with internal connectors that connect to the touch panel via pre-installed adapter cables (FIG. 5). This allows the Table-Top Stand to provide external connectors on the rear panel for ease-of-access.
The Bezel snaps on and off the NXD-43X, no screws are used or required. To remove the Bezel from the NXD-43X (FIG. 2):
Tab
Tab
from ETHERNET/POE port on NXD-43X
from USB port on NXD-43X
Panel Button Connector
NXD-43X Bezel
notch
notch
FIG. 2 Removing the Bezel from the NXD-43X
FIG. 5 NXA-TTS43X-BL - Internal Connectors To connect the Touch Panel to the internal connectors in the Table-Top Stand:
1.
ETHERNET/POE Port on the NXD-43X: Connect the RJ45 connector inside the Table-Top Stand to the ETHERNET/POE port on the side panel of the NXD-43X. USB Port on the NXD-43X: Connect the USB connector inside the Table-Top Stand to the USB port on the side panel of the NXD-43X.
2.
Step 5: Install The NXD-43X Into the Table-Top Stand At this point the touch panel can be installed in the TTS enclosure: 1. Slide the touch panel into the Table-Top Stand until the front of the panel sits flush against the front panel of the Table-Top Stand. Note: Be careful not to pinch or otherwise damage the cables connecting the NXD-43X to the internal connectors in the Table-Top Stand. 2. Use the two mounting screws (included with the Table-Top Stand) to secure the touch panel to the Table-Top Stand enclosure (FIG. 6). NXA-TTS43X-BL
Step 7: Install the Bezel on the NXA-TTS43X-BL The final step is to install the Bezel on the Table-Top Stand: the Bezel slides onto the Table-Top Stand from the rear. Slide the Bezel on to the NXA-TTS43X-BL, from the rear of the enclosure, until it snaps into place on the Table-Top Stand. FIG. 8 provides an exploded view of the entire assembly including the NXA-43X Bezel, Panel, Table-Top Stand and NXA-TTS43X-BL Bezel: NXA-TTS43X-BL Bezel
NXD-43X Bezel
NXD-43X Panel
NXD-43X Panel
Table-Top Stand
mounting screws
FIG. 8 Installing the Bezel on the Panel/Table-Top Stand assembly
FIG. 6 Inserting the NXD-43X into the NXA-TTS43X-BL - secure with 2 mounting screws
NXA-TTS43X-BL Rear Panel Connectors
Note: Do not use excessive force or over-tighten the screws - doing so could damage the touch panel.
Use the rear panel connectors on the NXA-TTS43X-BL to connect the touch panel to the control system. Once connected, these connectors behave exactly the same as the ETHERNET/POE and USB ports on the touch panel itself.
Step 6: Re-Install the Bezel on the NXD-43X The Bezel snaps on and off the NXD-43X, no screws are used or required. To re-install the Bezel on the NXD-43X: 1. Connect the button cable from the panel to the button cable connector on the inside of the Bezel (FIG. 7).
Secure Mounting / Alternate Cable Routing The NXA-TTS43X-BL features a cable routing knockout on the bottom panel, mounting holes and internal strain relief to provide a secure table-top installation option (FIG. 9). Surface Mounting holes
NXD-43X Panel (front) Button Connector Cable
Surface Mounting holes are beneath the rubber feet
Button Connector
Cable knockout The Strain Relief Bracket (mounted inside the enclosure) also uses this mounting hole
Tab Tab
NXD-43X Bezel
FIG. 7 Button Connector location (Inside Bezel) 2. •
3. 4.
Carefully align the Bezel with the front of the NXD-43X panel. Note the positions of the tabs on the top-front edge of the Table-Top Stand (see FIG. 7), and the corresponding tabs on the inside (top-front edge) of the Bezel. Note: Make sure to align the Light, and PIR Motion sensor locations to their respective openings on the Bezel. Gently press the top edge of the Bezel onto the top edge of the Table-Top Stand, and engage the metal tabs on the Table Top Stand with the matching notches on the Bezel. Gently press the bottom edge of the Bezel on to the bottom edge of the TableTop Stand until it snaps into place.
(rear)
FIG. 9 Bottom Panel (Alternate Cable Routing) Refer to the TTS Secure Mounting / Alternate Cable Routing Installation Guide (available at www.amx.com) for instructions.
Additional Documentation Refer to the NXD-430/435 Operation/Reference Guide (available at ww.amx.com) for details on wiring and connection information for the NXD-43X panels.
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s). 2/10 ©2010 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without notice at any time. 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-2262-40
REV: B
