Transcript
OC192
Optical carrier multirate interface for up to OC192 (STM64) / 10GbE
Description The OC192 is a dual-port mezzanine board that pairs with a PCI / PCIe main board to support multiple standards. Port 0 provides an optional SFP for 1GbE (optical or electrical), OTU1, or OC3/12/48 (STM1/4/16). Port 1 provides an XFP for 10GbE (optical or electrical), OTU2/2e, or OC192 (STM64). The board has one programmable Xilinx Virtex 4 FPGA and 4 GB of DDR2 DRAM for snapshot recording and buffering. EDT provides FPGA configuration files to support 1GbE and 10GbE (at the PHY layer); OC3/12/48/192 (raw, framed, framed and descrambled, header, and payload); OTU1/2/2e (raw, framed, framed and descrambled); and demultiplexing. Custom files can be requested. The main board supplies DMA, plus additional memory and programmable FPGA resources.
Features Mezzanine board — pairs with an EDT main board (PCI or PCIe), which adds DMA, programmable FPGA resources, and memory Port 0: One optional SFP for 1GbE (electrical or optical), OTU1, or OC3/12/48 (STM1/4/16); optical signals can be 1550, 1310, or 850 nm Port 1: One XFP for 10GbE (electrical or optical), OTU2/2e, or OC192 (STM64); optical signals can be 1550, 1310, or 850 nm
Applications
FPGA: One programmable Xilinx Virtex 4 LX XC4VLX40
Telecommunications network monitoring
DRAM: 4 GB (DDR2) for snapshot recording and data buffering
Ethernet monitoring SONET/SDH to ethernet conversion
EDT, Inc. | 1400 NW Compton Drive, Suite 315 | Beaverton, Oregon 97006 USA | Tel: +1-503-690-1234 (800-435-4350) | Fax: +1-503-690-1243 |
[email protected] | edt.com
OC192
Specifications Product Type
Optical carrier multi-rate interface for up to OC192 (STM64) / 10GbE; it requires an EDT PCI / PCIe main board.
FPGA Resources
One programmable FPGA (Xilinx Virtex 4 LX XC4VLX40), plus FPGA resources on main board
Memory
DRAM (DDR2)
4 GB for snapshot recording and buffering
Clocks (XO)
Port 0 can be set to: Port 1 can be set to:
125, 155.52, 156.25, or 166.62857 MHz 125, 155.52, 156.25, 166.62857, 161.13281, 167.33165, or 173.37075 MHz
Data Rates
Dependent on such factors as data format, main board, and system variables.
Data Format (I/O)
Port 0: Port 1:
Transceivers
Two (port 0 has an optional SFP, while port 1 has an included XFP) are available, supporting data as shown below.
1GbE (optical or electrical) 1000 BASE-T or -X —
10GbE (optical or electrical) — 10G BASE-CX4 or -R
ITU-T G.709 (optical) OTU1 OTU2/2e
SONET (SDH) (optical) OC3/12/48 (STM1/4/16) OC192 (STM64)
ELECTRICAL OPTICAL Port 0 1GbE, OTU1, or (1 SFP, optional) 1GbE OC3/12/48 (STM1/4/16) 1550 nm 1310 nm 850 nm Output power — –2 to 3 dBm –9.5 to –3 dBm –9 to –2.5 dBm Center wavelength — 1500 to 1580 nm 1270 to 1360 nm 830 to 860 nm Sensitivity — –28 dBm –18 dBm –18 dBm Maximum input power — –9 dBm 0 dBm 0 dBm Connector RJ45 LC LC LC Port 1 10GbE, OTU2/2e, or (1 XFP, included) 10GbE OC192 (STM64) 1550 nm 1310 nm 850 nm Output power — –1 to 2 dBm –6 to –1 dBm –3 to –1 dBm Center wavelength — 1550 nm 1290 to 1330 nm 850 nm Sensitivity — –15 dBm –13 dBm –7.5 dBm Maximum input power — –1 dBm –0.5 dBm –1 dBm Connector CX4 LC LC LC Connectors
One RJ45, LC, or CX4 on each transceiver as shown above
Cabling
Consult EDT for purchase options.
Physical
Weight Dimensions
6.5 oz. typical 6.6 x 4.2 x 0.75 in. (with a main board)
Environmental
Temperature (operating / non-operating) Humidity (operating / non-operating)
0° to 40° C / -40° to 70° C 1% to 90%, non-condensing at 40° C / 95%, non-condensing at 45° C
System and Software
For details on system requirements and EDT-provided software driver packages, see specifications for your EDT main board.
Ordering Options - Main board: PCI GS or PCIe8 LX / FX / SX - Transceivers: 1 or 2 [options above] Bold is default. For more options, see main board detail. Ask about custom options.
Contact EDT to discuss engineer-to-engineer support, from phone consults to custom design of hardware, firmware, or software.
20150605
