Transcript
OCTOBYTE OCTOBY TE The Faster 4/8 Pole Interconnect System ©
T HE FA S T E R 4 / 8 PO L E IN TE RC O N N E C T SYS TEM FOR E T H E R N E T DATA AP PL ICATIO N S
for Ethernet Data Applications APRIL 2015
The Faster 4/8 Pole Interconnect System for Ethernet Data Applications ITH connector with Octobyte™ contacts is available with fully dedicated ETHERNET protocol or in a combo version where a mix of signal-power and Ethernet is required. RoHS compliant, IP67 (IP68 on request) exceeds performance expections typical in harsh environmental applications found throughout Rail and Industrial markets.
Adam E. Moreira
OCTOBYTE™ contacts are vibration resistant and available to work with ETHERNET cables from CAT 5 to CAT 7A, MVB-WTB, RG58 Coax.
Masakazu Matsumoto
Commuter Applications
Passenger Information Systems
ITH connectors with OCTOBYTE™ contacts are easy and fast to assemble, making them best solution for harsh environment applications where signal reliability is a must: • Commuter Rail • Passenger Information Systems (Audio/Video/Digital displays) • Monitoring and Control (Braking/Doors/Lighting/Data) • Heavy Industry • Data Control • Safety Systems Tested according to: ISO F0 STP: CAT 7A EN50173-1 F600-STP: CAT 7 EN50173-1 D STP: CAT 5E Tested for compliance according to EN50173-1 standards set for CAT5E and CAT7. Testing was conducted using 12 jumpers, each 7.5 mt. in length for a total of 90 mt.
ETHERNET CAT 7A Contacts Number of Contacts 8 = 8 Poles
Q
0 Contact Size
8
Alternative Colour (See Table II)
Cable Range (See Table I)
P - X Contact Gender P = Male S = Female
Ø15.6
B1 -
XXX
Gold Plating
See Table I
Ø15.1
See Table I
Contact Bucket Detail
ETHERNET CAT 7A Contacts
Wire Size : AWG 22 - AWG 28
Data Transmission Ethernet Contacts for: »» • ETHERNET UP TO CAT 7A
Ø0.9 Max
Featuring: »» Internal crimpable contacts »» Inspectable contact »» Integrated cable clamp »» Low mating force
Technical Characteristics: »» Current rating: 5A max »» Voltage drop (at 5A and 25°C): 70mV max
Materials and Finish: »» Copper alloy and gold plating
Inserts: »» Thermoplastic resin UL94V0
- 7A
Table I Wire Size Type A B C
Cable O.D. Range 6-7 7-8 8-9
Table II Colour Code Colour Omitted For Standard G14 Black G14GN Green G14GY Grey G14R Red G14Y Yellow
ETHERNET CAT 5 Contacts Number of Contacts 8 = 8 Poles
Q
0
8
Contact Size
Cable Range (See Table I)
P - X Contact Gender P = Male S = Female
B1 Gold Plating
See Table I
Ø15.1
See Table I
Ø15.1
ETHERNET CAT 5 Contacts Data Trasmission Contacts for:
Contact Bucket Detail Wire Size: AWG 22 - AWG 28
»» • ETHERNET UP TO CAT 6A
Featuring: »» - Internal crimpable contacts »» - Inspectable contact »» - Integrated cable clamp »» - Low mating force
Technical Characteristics: »» - Current rating: 5A max »» - Voltage drop (at 5A and 25°C): 70mV max
Materials and Finish: »» - Copper alloy and gold plating
Inserts: »» - Thermoplastic resin UL94V0-NFF16-102 I2F3 Exigence 3
Ø 0.9 Max
Table 1 Wire Size Type A B C
Cable O.D. Range 6-7 7-8 8-9
COAX Contacts Contact Gender P = Male S = Female
Q
0
CX
Gold Plating
P - RG58 Cables: RG58 - 50 Ohm RG59U - 75 Ohm
Contact Size
Ø5.2 - 4.2 (Cable Range)
Ø15.1
Ø5.2 - 4.2 (Cable Range)
COAX Contacts Data Trasmission Contacts for: »» RG58 »» RG59U
Featuring: »» Internal solder contacts »» Inspectable contact »» Integrated cable clamp »» Low mating force
Technical Characteristics: »» Current rating: 5A max »» Voltage drop (at 5A and 25°C): 70mV max
Materials and Finish: »» Copper alloy and gold plating
Inserts: »» P.T.F.E.
B1
CONTACT BUCKET DETAIL WIRE SIZE : AWG 18 - AWG 22
1.2mm Max RG 58 = ØØ1.4 RG 59 U = Ø 1.0 mm
Ø15.1
ETHERNET MVB - WBT Contacts
Number of Contacts (4 = 4 Poles)
Q
0 Contact Size
4
Cable Range
(See Table I)
P - X Contact Gender P = Male S = Female
B1 - AD Gold Plating
See Table I
ETHERNET MVB - WBT Contacts Data Trasmission Contacts for:
Ø 15.1
See Table I
»» MVB - Multifunctional Vehicle Bus »» WTB - Wired Train Bus
Featuring: »» Internal crimpable contacts »» Inspectable contact »» Integrated cable clamp »» Low mating force
CONTACT BUCKET DETAIL WIRE SIZE : AWG 18 - AWG 22
Ø 1.2 Max
Technical Characteristics: »» Current rating: 5A max »» Voltage drop (at 5A and 25°C): 70mV max
Materials and Finish: »» Copper alloy and gold plating
Inserts: »» Thermoplastic resin UL94V0-NFF16-102 I2F3 Exigence 3
Table I Wire Size Type A B C
Cable O.D. Range 6-7 7- 8 8-9
Ø 15.1
Crimp Tool
wire to length shown.
3 Extraction and Crimping Tools Insertion, Insert wire into contact. The wire should be visible in the inspection hole.
Manual Crimping Tool 809-136
4
Manual Crimping Tool Turret Insert contact into crimp tool as shown. Make M.105015 809-138
sure that the contact is fully inserted into the tool. Squeeze handle completely. The ratchet mechanism will not allow a partial crimp. Release handle and remove contact.
Positioner
INSPECTION HOLE Positioner
809-005
3
5
Extraction Tool M.104010
Inspect crimped contact. Wire should be fully inserted and the crimp should be uniform in appearance.
Insertion / Extraction Tool
Insertion⁄Extraction 809-088 Tool 809-088 EXTRACTION TIP WHITE END
6
5
INSERTION TIP BLUE END
How to Order
Install contact into connector. Push the contact through the rear grommet until the contact locks into place. This can usually be done by hand without the need for a tool.Contact If the Gender wire gage is #26 030 = Rear Panel Mountingor Receptacle N0 = Without Backshell smaller, a tool is helpful. There are two techniques P = Male 06 = Straight Plug Please consul the factory Female for installing contacts with Sa =tool. One method is to push the contact in by hand, then use the tool to finish the insertion. The other method is to position the contact ITH 030the insertion A 5Ctip against 32-Q4 S shoulder, B0 N0 F6 then insert the contact. Use insertion/extraction tool 809-088 to install contacts. Slide the wire into Plating Insert Arrangements: See below. the groove on the blue end of theF6tool. Slide the For customized insert arrangement, = Electrodeposition of black paint (cataphoresis), tool please tip upconsult the contact until it touches the contact the factory RoHS compliant shoulder. USE CARE TO AVOID DAMAGING THE G3 = Cd + Olive drab, Not RoHS compliant CONNECTOR. Other Plating are available, Please consult the factory
6
7
Contact Extraction. Use tool 809-088. The white end is used for contact extraction. First, push 18-OB the wire into the groove of the metal tip. Slide the 1tipOCTOBYTE of the tool into the connector. Push the tool into the connector cavity until the tip bottoms in the connector. Avoid wiggling or rocking the tip. This may damage the cavity. A straight push is best. Pinch the wire between your finger and the white plastic grip and slide the tool and contact out of the connector. Wire insulation diameter greater than 0.045 inches 32-Q4 (1.14mm) is too large to work properly with the 4 OCTOBYTE extraction tool. connector damage is possible.
FRONT VIEW MALE INSERT
© 2010 Glenair, Inc.
28-OB4 2 OCTOBYTE 2 SIZE 8 CONTACTS
7 36-OB7 3 OCTOBYTE 4 SIZE 8 CONTACTS
Dimensions in inches (millimeters) and are subje CAGE Code 06324
Glenair Italia S.p.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 9120
Via del Lavoro, 7 - 40057 Quarto Inferiore - Granarolo dell’Emilia (BO) - Italy Tel.+39-051-782811 - Fax: +39-051-782259 -
[email protected] - www.glenair.it - www.glenair.com
www.glenair.com
Direct Link: www.glenair.com/octo/pdf/octo.pdf
A-4
01-JANUARY-2010
A World of
Interconnect Solutions Glenair, Inc.
1211 Air Way • Glendale, California • 91201-2497 Telephone: 818-247-6000 • Fax: 818-500-9912 •
[email protected] www.glenair.com
Telephone: Glenair Industrial Power and 203-741-1115 Signal Connector Group Facsimile: 25 Village Lane 203-741-0053 Wallingford, CT
[email protected] 06492
Glenair UK Ltd 40 Lower Oakham Way Oakham Business Park P.O. Box 37, Mansfield Notts, NG18 5BY England
Glenair Microway Systems 7000 North Lawndale Avenue Lincolnwood, IL 60712
Glenair Nordic AB Gustav III : S Boulevard 46 S - 169 27 Solna Sweden
Glenair Electric GmbH Schaberweg 28 D-61348 Bad Homburg Germany
Glenair Italia S.p.A. Via del Lavoro, 7 40057 Quarto Inferiore Granarolo dell’Emilia Bologna, Italy
© 2015 Glenair, Inc.
Telephone: 847-679-8833 Facsimile: 847-679-8849
Telephone: 49-6172-6816-0 Facsimile: 49-6172-6816-90
[email protected]
Telephone: 39-051-782811 Facsimile: 39-051-782259
[email protected]
Printed in Italy
Glenair Iberica C/ La Vega, 16 45612 Velada Spain
Glenair France SARL 7, Avenue Parmentier Immeuble Central Parc #2 31200 Toulouse France
Telephone: 44-1623-638100 Facsimile: 44-1623-638111
[email protected]
Telephone: 46-8-50550000 Facsimile: 46-8-50550001
[email protected]
Telephone: 34-925-89-29-88 Facsimile: 34-925-89-29-87
[email protected]
Telephone: 33-5-34-40-97-40 Facsimile: 33-5-61-47-86-10
[email protected]
