Transcript
Model 290
SECTION 3. PARTS INFORMATION 3-1. INTRODUCTION
This section lists the replaceable parts of the Henny Penny Model 290 fryer.
3-2. GENUINE PARTS
Use only genuine Henny Penny parts in your fryer. Using a part of lesser quality or substitute design may result in damage to the unit or personal injury.
3-3. WHEN ORDERING PARTS
Once the parts that you want to order have been found in the parts list, write down the following information: Item Number 2 Part Number 16738 Description High Limit
Example:
From the data plate, list the following information: Product Number 01100 Serial Number 0001 Voltage 208
Example:
3-4. PRICES
Your distributor has a price parts list and will be glad to inform you of the cost of your parts order.
3-5. DELIVERY
Commonly replaced items are stocked by your distributor and will be sent out when your order is received. Other parts will be ordered, by your distributor, from Henny Penny Corporation. Normally, these will be sent to your distributor within three working days.
3-6. WARRANTY
All replacement parts (except lamps and fuses) are warranted for 90 days against manufacturing defects and workmanship. If damage occurs during shipping, notify the carrier at once so that a claim may be properly filed. Refer to warranty in the front of this manual for other rights and limitations.
3-7. RECOMMENDED SPARE PARTS FOR DISTRIBUTORS
Recommended replacement parts, stocked by your distributor, are indicated with √ in the parts lists. Please use care when ordering recommended parts, because all voltages and variations are marked. Distributors should order parts based upon common voltages and equipment sold in their territory.
106
3-1
Model 290
3-8. INDEX OF PARTS LIST ILLUSTRATIONS
Title
Fig. No.
FRAME AND COVER ASSEMBLY .............................................................
3-1
3-3
ELEMENT ASSEMBLY ................................................................................
3-2
3-5
COUNTERWEIGHT SYSTEM .....................................................................
3-3
3-6
LID ASSEMBLY ...........................................................................................
3-4
3-7
CONTROL PANEL ASSEMBLY ..................................................................
3-5
3-8
BEHIND CONTROL PANEL COMPONENTS ...........................................
3-6
3-9
FILTER PUMP ASSEMBLY (SN: LG012JC & BELOW) .............................
3-7A
3-10
FILTER PUMP ASSEMBLY (SN: LG013JC & ABOVE) ..............................
3-7B
3-12
DRAIN VALVE & DRAIN SWITCH ASSEMBLIES ...................................
3-8
3-14
DRAIN PAN AND FILTER ASSEMBLY ......................................................
3-9
3-15
CARRIER, RACKS & JUNCTION BOX ASSY ..........................................
3-10
3-17
3-2
Page No.
104
Model 290
Figure 3-1. Frame and Cover Assembly
205
3-3
Model 290
Figure & Item No. 3-1 1 2 √ 3 4 5 6 7 8 9 10 11 12 12 13 14
Part No.
Description
39796 53669 29898 54225 53673 37246 SC03-005 66934 SC01-215 37291 35726 66933 14457 36337 SC02-023
FRAME & COVER ASSEMBLY WELDMENT – CONTROL PANEL FRONT .......... GUARD – POWER SWITCH ................................... SWITCH – POWER ................................................. 1" INSERT – LEG MACHINED ............................... CASTER, SWIVEL 4" ............................................... CASTER W/BRAKE & SWIVEL LOCK ................. SCREW - - #8 x 1/2” PH PHD .................................. SIDE PANEL – RIGHT ............................................. SCREW - 5/16-18 x 2.5” HEX HD BOLT ................ REAR SHROUD – ACCESS ASSEMBLY ................ TOP COVER – REAR SHROUD .............................. SIDE PANEL – LEFT ................................................ KIT - SOUND DEADENING ................................... DOOR – ACCESS .................................................... SCREW - #8-B x 3/8” PH THD SS ...........................
Qty.
1 1 1 4 2 2 4 1 4 1 1 1 1 1 5
√ recommended parts
3-4
106
Model 290
Figure & Item No. 3-2 1 2 3 4 5 6 √ 7 √ 7 √ 7 √ 7 8 9 10
Part No.
Description
SC01-083 35101 35100 SC01-074 35435 35462 35234 35598 48367 36290 16855 WA01-005 NS01-017
ELEMENT ASSEMBLY SCREW, (#10-32 x 1/2 PH FHD) .............................. SUPPORT, ELEMENT - LONG ................................ SUPPORT, ELEMENT - SHORT .............................. SCREW, (#10-32 x 1/2 PH THD S) ........................... BRACKET, HI LIMIT PROBE .................................. BRACKET, HI LIMIT PROBE .................................. HEAT ELEMENT ASSEMBLY, 8.5 KW 208V .......... HEAT ELEMENT, 8.5 KW 240V .............................. HEAT ELEMENT, 230 V(Int’l Only) .......................... HEAT ELEMENT, 220 V(Int’l Only) .......................... SEAL, O-RING ......................................................... WASHER, (5/8 DIA. TYPE A - SERIES N) ............... NUT, (5/8-18 B HEX) ................................................
Qty.
As Required
5 5 As Required
3 3 2 2 2 2 4 8 4
√ recommended parts
106
3-5
Model 290
Figure & Item No. 3-3 1 √ 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Part No.
Description
35026 140225 NS01-025 LW01-010 35092 SC01-069 36839 SC01-042 36625 36627 36626 37362 37363 37364 SC01-081
COUNTERWEIGHT SYSTEM ARM, LID SUPPORT ..................................................... KIT-CABLE (2 CABLES) ............................................... NUT, HEX 5/16-18 SS ..................................................... WASHER, 3/8 SPLIT RING SS ...................................... CARRIAGE ...................................................................... SCREW, 3/8-16 X 1-1/2 HEX HD S2P ........................... SLIDE ............................................................................... SCREW, 3/8-16 X 1 HEX C ............................................. WELD ASSEMBLY, C/W CARRIAGE .......................... COUNTERWEIGHT BAR .............................................. SPACER, C/W FRAME .................................................. WHEEL, CARRIAGE ..................................................... SPACER, CARRIAGE WHEEL ..................................... SPINDLE .......................................................................... SCREW, 3/8-24 X 3/4 HEX HD SS .................................
Qty.
2 1 10 10 1 8 2 2 1 4 2 4 4 4 4
√ recommended parts 3-6
712
Model 290
Figure & Item No.
Part No.
3-4 1 2 3 4 5 6 7 7a 7b 8
65818 RR01-004 WA01-020 51531 SC01-041 55754 55756 59169 52498 51707 SC01-248
512
Description Lid Assembly Complete Ring - Retaining - 1/2 in. Washer - .513 ID-.750 OD-.05 THK Stop - Lid, Cast Screw - 5/16”-18 x 1 HEX HD C Handle Weld Assembly Assy. - Latch/Sleeve Coat Lid Latch Bracket Spring - Lid Latch Lid Latch Bracket Screw 10-32 x 1.25 PH THD SS
Qty. 1 1 1 2 1 1 1 1 1 2
3-7
Model 290
Figure & Item No. 3-5 √ 1 √ 1 √ 1 2 3 4 √ 5 6 7 8 9*
Part No.
Description
55848RB 93553 72160RB 50624 61748 NS02-005 51877 SC01-049 NS02-005 72500 14620
CONTROL PANEL ASSEMBLY CONTROL ASSY – KFC 290 SMS ...................... ASSY-CONTROL-KFC ZIGB 290-DOM ............ CONTROL ASSY – 290 SMS-W/O SETPOINTS CONTROL DECAL – 8 HEAD KFC .............. MENU CARD .................................................. NUT ................................................................. WIRE/SPEAKER ASSY .................................. SCREW ........................................................... NUT ................................................................. ASSY – CONTROL COVER STUD .............. KIT - CONTROL RETRO - 292 TO 290 ..............
√ recommended parts
3-8
Qty.
1 1 1 1 1 4 1 4 4 1 1
613
Model 290
7
1 6
5
4
2
Figure & Item No.
Part No.
√ √ √ √ √
3-6 1 1* 1* 2 3 4 √ 5 √ 5 √ 6
29942 65075 65074 30971 19405 17216 16738 60241 EF02-125
√ 6
18364
√ √ √ √ √
EF02-006 EF02-007 EF02-104 EF02-105 14335
6 6 6 6 7
3
Description
Qty.
BEHIND CONTROL PANEL COMPONENTS CONTACTOR - MERCURY 208/240 VAC ..............
1
ASSY.-240V E/M HEAT CONTACTOR-CE-240V (UK)
1
ASSY.-240V E/M HEAT CONTACTOR-CE-230V .. CAPACITOR-RESISTOR ASSY .............................. CONTACTOR KIT - 208/240 VAC .......................... BRACKET ASSY- HIGH LIMIT .............................. 450° F HIGH LIMIT .................................................. 425° F HIGH LIMIT - CE .......................................... BREAKER-PUSH BUTTON RESET-15 AMP .......... SN: BE0608003 & ABOVE FUSE HOLDER ASSY - 15 AMP .............................. SN: BE0608002 & BELOW FUSE HOLDER .................................................. FUSE - 15 AMP .................................................. FUSE HOLDER - 20A-250V .................................... FUSE - 15 AMP - CE ................................................ PROBE KIT ...............................................................
1 1 1 1 1 1 2 2 2 2 1 1 1
√ recommended parts/* not shown 307
3-9
Model 290
Pump Interior
3-7A. FILTER PUMP ASSEMBLY (SN: LG012JC & BELOW)
3-10
205
Model 290
Figure & Item No.
Part No.
3-7A 1 2 √ 3 4 5 6 7 8 9 10 √ 11 12 √ 13 14 15 16 17 18 19 √ 20 √ 21 √ 22 √ 23 √ 24 √ 25 √ 26 √ 27 √ 28 29*
18107 54484 17476 18105 18644 51831 55836 16808 16809 17407 67583 62206 17430(use 69289) 16807 FP01-122 FP02-024 35472 FP02-007 17437 17454 17456 17451 SC01-016 SC01-026 SC01-132 17447 17446 17453 67589
Description FILTER PUMP ASSEMBLY CONDUIT CONNECTOR 3/8 X 90 .............................. BLOWER/PUMP – FLEXIBLE CONDUIT .................... PUMP SEAL KIT ............................................................ ANTI SHORT 3/8 INCH ................................................. CONDUIT CONNECTOR 3/8 X 90 .............................. PUMP CONDUIT BRACKET ........................................ ASSY – OIL RETURN LINE .......................................... SLEEVE, FITTING ................................................... NUT, FITTING ......................................................... CONNECTOR, 1/2 MALE ELBOW .............................. MOTOR – FILTER PUMP .............................................. ASSY - TUBE - PUMP TO DISCON - 590 ................... UNION, MALE FITTING .............................................. FITTING, CONNECTOR MALE ................................... REDUCER, 3/8 TO 1/2 ................................................... NIPPLE, CLOSE 3/8 ...................................................... CHECK VALVE - PRESSURE ....................................... NIPPLE 3/8 X 1-1/2 ........................................................ PUMP SUBASSY 8GPM ................................................ BODY - PUMP ......................................................... PUMP SHIELD ......................................................... COVER - PUMP ....................................................... PLUG 1/4 HEX COUNTERSUNK ........................... SCREW 5/16-18 X 3/4 HEX HD C .......................... 1/4-20 X 5/8 SOC HD CAP SCREW ....................... ROTOR - PUMP ....................................................... ROLLER - TEFLON SET ......................................... PUMP O RING GASKET ......................................... ASSY - FILTER PMP & 1/2 HP MOTOR .......................
Qty. 1 1 1 2 1 1 1 2 2 2 1 1 1 1 1 1 1 1 1 1 2 1 1 2 4 1 1 1 1
√ recommended parts
707
3-11
Model 290
Pump Interior
3-7B. FILTER PUMP ASSEMBLY (SN: LG013JC & ABOVE)
3-12
205
Model 290
Figure & Item No. 3-7B 1 2 √ 3 4 5 6 7 8 9 10 √ 11 12 13 14 √ 15 16 17 18 √ 19 √ 20 √ 21 √ 22 √ 23 √ 24 √ 25 √ 26 √ 27
Part No. 18107 54484 17476 18105 18644 51831 66618 16808 16809 FP01-169 67583 FP01-089 17407 62206 17430(use 69289) 21800 FP02-021 64218 SC01-132 23469 23468 23647 17456 23470 FP01-020 SC01-026 17453
Description FILTER PUMP ASSEMBLY CONDUIT CONNECTOR 3/8 X 90 ........................... BLOWER/PUMP – FLEXIBLE CONDUIT ................. PUMP SEAL KIT ......................................................... ANTI SHORT 3/8 INCH .............................................. CONDUIT CONNECTOR 3/8 X 90 ........................... PUMP CONDUIT BRACKET ..................................... ASSY – OIL RETURN LINE ....................................... SLEEVE, FITTING ................................................ NUT, FITTING ...................................................... CON-90 MALE 3/4 TUBE 3/4 NPT ............................ MOTOR – FILTER PUMP ........................................... BUSHING - REDUCING 3/4M TO 1/2F .................... CONNECTOR, 1/2 MALE ELBOW ........................... ASSY - TUBE - PUMP TO DISCON .......................... UNION, MALE FITTING ........................................... VALVE - 3/4 CHECK .................................................. NIPPLE - 3/4 NPT X 3 IN LG BL ............................... PUMP SUBASSY 8GPM ............................................. 1/4-20 X 5/8 SOC HD CAP SCREW .................... ROLLER - 7 GPM PUMP ...................................... ROTOR - 7GPM PUMP ........................................ BODY - 7 GPM PUMP .......................................... PUMP SHIELD ...................................................... CAP - 7 GPM PUMP ............................................. PLUG 1/4-18 HEX LEVEL SEAL .......................... SCREW 5/16-18 X 3/4 HEX HD C ....................... PUMP O RING GASKET ......................................
Qty. 1 1 1 2 1 1 1 2 2 2 1 1 1 √1 1 1 1 1 4 5 1 1 2 1 1 2 1
√ recommended parts
106
3-13
Model 290
Figure & Item No.
Part No.
3-8 1 1 2 3 √ 4 5 6 7 7 8 9 10*
65520 66553 SC01-058 WA01-006 54228 NS02-005 52519 65522 67220 EF02-017 67617 76579
Description DRAIN VALVE & DRAIN SWITCH ASSEMBLIES DRAIN VALVE ASSEMBLY (SN: LG012JC & BELOW) DRAIN VALVE ASSEMBLY (SN: LG013JC & ABOVE) . SCREW #6-32 X 1 PH. PAN HD. .................................. WASHER #6 TYPE A ..................................................... DRAIN SWITCH W/BOOT ........................................... NUT #6-32 HEX ............................................................. CORD ASSY., DRAIN INTERLOCK ............................ BRACKET, SWITCH (BEFORE DEC. 29, 2003) .......... BRACKET, SWITCH (AFTER DEC. 29, 2003) ............. STRAIN RELIEF ............................................................ BRACKET - MICROSWITCH TRIGGERING .............. PLATE - D/I SWITCH COVER ......................................
Qty. 1 1 2 2 1 2 1 1 1 2 1 1
√ recommended parts
3-14
707
Model 290
3-9. DRAIN PAN AND FILTER ASSEMBLY 205
3-15
Model 290
Figure & Item No.
Part No.
Description
3-9 1 2 2 2 3 4 5 6 7
52194 03203 21471 24429 52496 52487 SC01-009 NS02-002 17505
DRAIN PAN AND FILTER ASSEMBLY CRUMB CATCHER (OPTIONAL) ............................ CRUMB CATCHER BASKET W/HANDLE (OPTIONAL) “COLD ZONE” CRUMB CATCHER BASKET ASSY HANDLE - CRUMB BASKET ................................... FILTER DRAIN PAN ASSEMBLY ............................ CASTER ....................................................................... SCREW 1/4-20 X 1/2 .................................................... NUT 1/4-20 ................................................................... FILTER CLIPS .............................................................
8 8 9 10 11 11
√ 12 √ 13
√ √ √
14 15 16 17 18 19 19 20 21 22 23 24 25 26
17503(use 14674) 65447 17502(use 14674) 36305 24212 14658 17431(use 69289) 17432(use 69289)
24211 23740 SC01-245 23804 OR01-007 23803 66535 62082 12102 65776 35771 35310 12126 65211
Qty.
1 1 1 1 1 2 8 8 2
BOTTOM FILTER SCREEN (SN:BE0503009 AND BELOW) .. BOTTOM FILTER SCREEN (SN: BE0503010 AND ABOVE) .. TOP FILTER SCREEN (SN:BE0503009 AND BELOW) ........... WASHER & STANDPIPE ...................................................... STANDPIPE ASSEMBLY (SN:BE0503009 AND BELOW) ...... KIT, 8 HEAD PICK-UP TUBE (SN BE0503010 & ABOVE)
1 1 1 1 1
UNION - MALE FITTING .......................................... UNION - HANDLE FITTING .................................... WELDMENT, FILTER TUBE AND WASHER ......... HANDLE, STANDPIPE 8 HEAD .............................. SCREW 10-32 X 1/2 ..................................................... INSERT, FILTER NUT ................................................ O-RING, FILTER NUT INSERT ................................. FILTER NUT (SN:BE0503009 AND BELOW) .......... FILTER NUT (SN BE0503010 & ABOVE) ................ FILTER DRAIN PAN COVER ASSEMBLY ............. FILTER ENVELOPE PAPER (100 PER CARTON) . ROD - LONG CLEAN OUT ....................................... BRUSH ......................................................................... STIRRER ...................................................................... BLACK L-BRUSH ...................................................... CRUMB CATCHER ....................................................
1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1
√ recommended parts
3-16
307
Model 290
Figure & Item No. 3-10 1 2 3 4 4 5 √ 6 7 8 8
9*
Part No. 67591 44782 35308 62126 62127 62106 51057 SC01-023 65180 65181 58146* 37560* 21519
Description CARRIER, RACKS & JUNCTION BOX ASSY CARRIER ASSY ............................................................. RACK HALF SIZE – 8 HEAD FRYER ........................... WELDMENT - RACK HANDLE ................................... JUNCTION BOX ASSY ................................................. JUNCTION BOX ASSY - CE ........................................ JUNCTION BOX - MACHINED ................................... ASSY - EMC FILTER - CE ............................................ SCREW #6-32 X 1/4 PH RHD C .................................... ASSY - MAIN POWER CORD ...................................... CORD - 291/591 POWER ........................................ PLUG-90, 60A, 3PH, 250V, #15-60P ....................... RECEPTACLE #15-60R ................................................. COVER - WIRE RACK (OPTIONAL) ..........................
Qty. 1 5 1 1 1 1 1 8 1 1 1 1 4
√ recommended parts/*not shown 1209
3-17
