Transcript
BLANK
MUST READ THIS BEFORE RUNNING Running a nitro kit is fun and easy, but to make this a safe and good experience you must observe a few rules. This kit is extremely fast, easily over 40MPH, and can seriously injure someone if you are not careful. Where to run car? • Any running area you choose must be dry. Do not run car near any water or wet dirt. • Do not run on public streets. It is very easy to have the car run over or damaged by hitting the curb. • Do not operate car in tight confined places. The car is very fast and will easily hit something. • Do not run near people or animals. The car is very fast and will too easily hit someone. • Due to noise, you will want to consider the surrounding area when operating the car. • Do not operate the car at night. You will not be able to drive it without hitting something. • Do not operate the car indoors. Engine exhaust is not healthy. Glow Fuel • Glow fuel is poisonous! • Glow fuel is flammable! • Do not leave in fuel bottle with lid off at any time. • Do not use any fuel other than glow fuel in this engine. First Time Starting the Engine Caution! When starting engine make sure the following is observed. • Set engine Master needle to 3 turns (rich setting) • Do not do this alone, get an experienced friend to help at first. • Fill fuel tank, try not to spill fuel. Do not spill fuel on receiver • Hold car off the ground, so it will not runaway when first starts • Turn on Radio and check the linkage before starting engine. • Turn on car receiver battery switch. • Always have an air filter on the carburetor to keep dirt out of engine. Engine Break-in • See Engine Page. Emergency Stopping Engine When Running • Remove air filter and cover carb. intake. • Squeeze fuel line and hold until engine stops. • With a rag, cover exhaust outlet. Storing Car After Running • Remove fuel from tank and fuel lines • Turn off radio in car • Put a few drops of after run in engine to keep it from rusting.
• Clean oil and dirt from chassis with a degreaser like Simple Green. Precautions • This kit is not a toy. Always run car with a second person as a spotter and pitman. • Hot Parts - The pipe, manifold, engine and head are very hot and will cause burns. • Rotating Parts - Keep hands away from the drive train, wheels, and engine when engine is running. • Radio - Check batteries life before running the car. If radio does not have full control of the car with steering and/or throttle/brake do not run until corrected. Failure to correct this will result in possible injury and damage to the car or property. • Glow fuel - Do not leave the glow fuel unattended with the lid off. Fuel contains Methanol and Nitro Methane both are flammable and poisonous. •Store fuel in cool ventilated location. Refer the glow fuel label for additional precautions. • Car Fuel tank - Never store fuel in car tank, it will ruin the engine if left in tank. • Always turn off the car BEFORE turning off radio. • DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY ISSUE.
IF YOU DO NOT BREAK-IN ENGINE CORRECTLY, MAINLY AT LOW RPM, YOU WILL BREAK THE CONNECTING ROD!
FAILURE TO NOT READ AND FOLLOW BREAK-IN ENGINE INSTRUCTIONS WILL VOID WARRANTY! CHECK RADIO SETTING, LINKAGE BEFORE STARTING.
REQUIRED FOR OPERATION THINGS NEED BESIDES THE KIT 3.5 cc (21 Class) ENGINE REAR EXHAUST OFNA/Picco P-9R EVO #51219
Glow Plug Long Heat with Battery & Charger # 10215....$27.95 (please note OFNA Glow Heats available) Glow Fuel 20%
Bottle’s with spout # 10160 - large 500cc # 10161 - large 500 ccAuto Stop # 10162 - small 250cc # 10164 - CNC spout 500CC # 10167 - CNC spout 800CC Off-Road Starter Box, 12V motor # 10250 - 1/8 scale Starter Box # 10253 - 1/8 scale Starter Box w/ Panel Off-Road Starter Box, two 550 motors # 10248 - 1/8 scale Starter Box # 10249 - 1/8 scale Starter Box,RTR Optional Parts # 92571 - Power Panel Glow Heater # 92572 - Cable for Glow Plug
Note: Pro kit does not include engine!
12V Battery for Starter Box (must have)
AA Batteries ( 12 pcs ) for radio
Radio must be set at neutral position before installing in the kit. SEQUENCE TO SET NEUTRAL
RADIO CONTROL UNIT
More Optional Parts . . .
#10202 NiHm Battery Hump Pack .. $34.95
Install AA batteries in Radio. Extend the antenna.(Transmitter) Install batteries into Car receiver . After installing the battery, connect the battery box. Extend the antenna. (Receiver)
# 10214 NiHm Battery Pack Charger.. $7.95
Set the trim-lever at center. Turn on the switch. (Transmitter)
Note: Carefully read the instruction manual of your 2 channel radio controller before using.
Turn on the switch. (Receiver) Make sure the servos are in command.
SUITABLE SERVO SIZE
When the operation stick is in neutral, servo horns must be in neutral as will. *Adjustment can be made by reinstalling the servo horn.
-41mm 36mm
# 51007 OFNA/Picoo Glow Plug .. $13.95
15mm - 21mm Turn off the switch. (Receiver) 11 Turn off the switch. (Transmitter)
29mm - 42mm
12 Retract the antenna. (Transmitter) 13
TOOLS NOT INCLUDED IN KIT Instant Cemment Cutter
Phillips Type Screw Drivers ( L ) Curved Scissors
INCLUDED WITH KIT Masking Tape 1.5mm Allen Wrench
Phillips Type Screw Drivers ( S ) Precision Caliper 2mm Allen Wrench
Brush Needle Nose Pliers
Knife
Paints
Cross Wrench
2.5mm Allen Wrench
4mm'5mm Allen Wrench
PLASTIC PARTS FOR USE 40533 FRONT AND REAR GEAR BOX
40537 REAR UPPER ARM
40538 DIFF. CASE
40717 FRONT AND REAR LOWER ARM
40716 FRONT UPPER ARM
40718 FRONT KNUCKLE ARM
31304 REAR UPPER RIGHT
40643 SHOCK PLASTIC
Parts For Not Use 40721 FRONT BUMPER 30800 Throttle Linkage Plastic
40040 CENTER DIFF. MOUNT PLASTIC PARTS
PLASTIC PARTS FOR USE 40539 SERVO SAVER
40541 RECEIVER BOX
40722 EXHAUST GAS DEFLECTOR
Parts for Not Use
40735 EXHAUST PIPE DETAIL PARTS AND BACK MIRROR
40719 ARM HOLDER
40720 SIDE IMPACT BUMPER AND BODY POST
40734 REAR WING AND WING MOUNT
SYMBOL USED THROUGHOUT THE INSTRUCTION MANUAL
Degrease With Motor Spray
Parts Bag Used
Do Not Over Tighten
Tighten
BAG Do Not Over Tighten
Screw Cement
Apply Screw Cement
Apply Oil Oil
Ensure Free Movement
True-To-Scale
1:1
Contact Adhesive Contact Adhesive
Tighten
Apply Grease Apply Grease
Ensure Free Movement
Anti-clockwise Rotation
Clockwise Rotation Rotate Direction
Rotate Direction
1 ASSEMBLY OF THE FRONT SHOCKS Step 1
*Assemble 2 seets for front
40636 *Fit the o-ring into groove beforeassembly.
Step 2
Step 3
Step 4
*Be careful not to damage shock shaft.
Fill the shocks with oil #80.
40640 40634 30403 40090 3.5mm O-Ring
40090 40090 2mm
40633
.....x4
40736
40643(Short)
40090 40090 1mm Washer
40090 2mm Washer
.....x2
Oil
40090 1mm 40090
2.6x5mm
40737
2.6x5mm
40638
.....x2
40060 Oil
.....x2
Step 5
1.Pull down piston and pour oil into shock cylinder. 2.To remove air bubbles by slowly moving piston up and down. 3.Pull down piston, attach pressure top and shock oil overflow with tissue paper.
Step 6
Tighten
CORRECT SHOCK ASSEMBLY Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ball end and the shock is 14mm. N.B. Do not over tighten as the plastic will strip.
40738
14mm
40090 7mm R-Ring
40643 OK
0
10
20
30
40
2 ASSEMBLY OF THE REAR SHOCKS Step 1
*Assemble 2 seets for rear
40636 *Fit the o-ring into groove beforeassembly.
Step 2
Step 3
Step 4
*Be careful not to damage shock shaft.
Fill the shocks with oil #80.
40640 40634 30403 40090 3.5mm O-Ring
40090 1mm Washer
40090
.....x4
40633
40090 2mm
40643(Short) 40054
40090 .....x2 40090 1mm
Oil
2.6x5mm
40090 40090 2mm Washer
.....x2
40638
40632
2.6x5mm Oil 40090 7mm R-Ring
.....x2
Step 5
CORRECT SHOCK ASSEMBLY Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ball end and the shock is 32mm. N.B. Do not over tighten as the plastic will strip.
Tighten
40751
32mm
1.Pull down piston and pour oil into shock cylinder. 2.To remove air bubbles by slowly moving piston up and down. 3.Pull down piston, attach pressure top and shock oil overflow with tissue paper.
40060
Step 6
OK
40643
0
10
20
30
40
1
4 ASSEMBLY OF THE FRONT AND REAR DIFF. Builds two differentials for front and rear.
NO.2
BAG
Step 1
Step 2 40513 Diff. Gear
Oil 40010 2.5x13.8mm Pin
36053 8X16mm Ball Bearing
.....x4
40538 Diff. Case 94034 4x4mm Set Screw
40010 2.5x13.8mm Pin
.....x2
40514 Cap Joint
40009 P6 O-Ring
40009 P6 O-Ring
40009 P6 O-Ring
.....x4
36053 8X16mm Ball Bearing
40517 43T Large Bevel Gear
40514 Cap Joint
4X4 mm Set Screw
40513 Diff. Gear (Large) 36053 8x16mm Ball Bearing
Oil
40010 2.5x13.8mm Pin
.....x4
5 ASSEMBLY OF THE FRONT AND REAR DIFF. Builds two differentials for front and rear.
NO.1 NO.12
BAG
Tighten
NB. It is very important to remove the 30776 washer if the gear mesh is too tight.
Step 1
Step 2 3X12mm Flat Head Hex Screw
30776 4X10mm Washer 30773 4mm Cross Pin
30776 4x10mm Washer
40513 Diff. Gear (Small)
40011 Diff. Gasket
.....x16
Tight the diff screws in this order.
94020 3x12mm Flat Head Hex Screw
30773 4mm Cross Pin
.....x8
D if f. Oi l
*Put the Diff. Oil #100000 for front and the #50000 for Rear *Fill the Diff. case to approx. 80% with the Diff. Oil
.....x4
6 ASSEMBLY OF THE FRONT AND REAR GEAR CASE NO.2 NO.4 BAG NO.5
94015 4x35mm Hex Screw
2
ew Scerment C
.....x8
40024 13X16X0.2 mm Shim
94011 4x16mm Hex Screw
4
Step 2
40519 Cap Joint
40533 Gear Case
36053 8x16mm Ball Bearing
3
Builds two gear case for front and rear. 94036 5x5mm Set Screw
Step 1
40024 13x16x0.2mm Shim
1
Apply Grease
36053 8X16mm Ball Bearing
.....x4
36053 8X16mm Ball Bearing
4X16mm Hex Screw
40516 13T Small Bevel Gear .....x4 40024 13X16X0.2mm Shim
.....x4
4X35mm Hex Screw
A ¡¯ d ju s th e b a c k l @ ¡ith w e s m .
2
40533 Gear Case
7 ASSEMBLY OF THE SERVO SAVER BAG
40037 Steering Plate Hex Screw
NO.3 40563 Servo Saver Tube(Hard-Coated)
Step 1
40073 4x8mm Flange Bearing
Step 2
*Tighten the steering plate hex screw all way down and then back it off 1/2 turn.
Oil 40539 Servo Saver Horn
40024 13x16x0.2mm Shim
40073 4x8mm Flange Bearing
40037 Steering Plate Hex Screw
40560 Alum. Servo Saver Connecting Plate (Hard-Coated)
40539 Servo Saver Horn
.....x2
40500 Servo Saver Spring (Black)
40024 13X16X0.2mm Shim
.....x2
Ensure Free Movement
40539 Servo Saver Horn
40034 Servo Saver Spring Tension Adjuster .....x2
Rotate Direction
* Notice the direction of the servo saver connecting plate.
8 ASSEMBLY OF THE SERVO SAVER 3x10mm Step 1
Step 2 40745
94041 3mm Nylon Nut
40531
.....x5 40539 3mm
94003 3x10mm Hex Screw
.....x5
40719 40719
40531 Shock Ball End Post
3mm
S Cecrew me nt
40719
.....x2
Right
Left
90018 3x25mm Cap Screw
ew Scrment Ce
3x25mm
*Set the left and right hand side upper arm adjuster in the same direction.
.....x2
9 ASSEMBLY OF THE SERVO SAVER BAG
NO.3
40074 6x10x3mm Ball Bearing
4x12mm Flat Head Hex Screw
Screw Cement
40074 6x10x3mm Ball Bearing
Screw Cement
94026 4x12mm Flat Head Hex Screw
40074 6x10mm Ball Bearing
.....x2
.....x4
40074 6x10x3mm Ball Bearing
40511 Servo Saver Post
3
10 ASSEMBLY OF THE STEERING TIE-ROD BAG
Assembly of the right and left hand side are the same.
NO.3
Step 2 40548 3mm Nylon Nut (Thin Type)
40038 7mm Ball
Step 1
40548 3mm Nylon Nut(Thin Type) .....x2
36700 7mm Steering Ball End 40038 7mm Ball
40126 3X6mm Flange Washer
.....x2 36790 4x46mm Turnbuckle
40038 7mm Ball
36700 7mm Steering Ball End
.....x4
40126 3X6mm Flange Washer
Screw Cemen t
1:1
94021 3x15mm Flat Head Hex Screw
Approx. 29.30 mm 29.30 mm 36700 7mm Steering Ball End
.....x4
11 ASSEMBLY OF THE SERVO SAVER AND FRONT UPPER ARMS
BAG
NO.3 NO.4
Assembly of the right and left hand side are the same.
4x10mm Hex Screw
Step 1
94020 3x12mm Flat Head Hex Screw
40533 Front Plate Bad .....x2
Front 94026 4x12mm Flat Head Hex Screw
94009 4x10mm Hex Screw
.....x4
.....x2
40525 3x48.1mm Arm Shaft .....X2
Step 2 40716 Front Upper Arm
40525 3x48.1mm Arm Shaft 40716 Caster Angle Adjuster (1mm and 3mm)
*Insert the upper arm adjust into shock stay.
40719 Upper Arm Adjuster
40716 Caster Angle Adjuster (2mm) 40525 3x48.1mm Arm Shaft
4x12mm Flat Head Hex Screw
Left 3x12mm Flat Head Hex Screw
Right
40719 Shock Stay *Set the left and right hand side upper arm adjuster in the same direction.
4
12 ASSEMBLY OF THE FRONT SHOCK STAY BAG
Assembly of the right and left hand side are the same.
NO.4 3x16mm Hex Screw
Ensure Free Movement
40719 Shock Mount(A)
40719 Shock Mount(B) 36742 Shock Cap Bushing
.....X2
35958 5x8x2.5mm Ball Bearing
.....X4
35958 5x8x2.5mm Ball Bearing
36742 Bushing
"L"make are for inside.
94005 3x16mm Hex Screw
.....x2
13 ASSEMBLY OF THE FRONT SHOCKS ONTO SHOCK STAY 3x8mm Washer
BAG
Assembly of the right and left hand side are the same.
3mm Nylon Nut
NO.1 40643 Shock Cap Washer Do Not Over Thigten
94041 3mm Nylon Nut
.....x2
94040 3x8mm Washer
.....x2
40643 Shock Cap Washer
94004 3x12mm Hex Screw
3x12mm Hex Screw
*Take the shock cap washer from the shock plastic tree.
.....x2
.....x2
14 ASSEMBLY OF THE REAR SHOCK STAY AND UPPER ARMS 13
Step 1
36850 7mm Ball
Assembly for both right and left side.
Step 2 40537 40750
.....x2
4x12mm 94003 3x10mm Hex Screw
.....x2 36850 36861
94010 4x12mm Hex Screw
.....x4
3x10mm
40065
1:1 Approx. 12.5 mm
15 ASSEMBLY OF THE REAR UPPER ARMS
Right
Left
40716(1mm)
*Set the left and right hand side upper arm adjuster in the same direction. 40716(2mm)
40719
40719
94011 4x16mm Hex Screw
.....x2
40546
40719 40546 3x42.7mm Arm Shaft
*Insert the caster angle adjuster onto arm shaft.
4x16mm
.....x2
16 ASSEMBLY OF THE REAR BRACE 4x12mm
40539 94010 4x12mm Hex Screw
.....x2
94011 4x16mm Hex Screw
.....x1
40539
4x16mm
17 ASSEMBLY OF THE TWO SPEED GEARS BAG
NO.7 35235 Clutch shoe Carrier
Step 1 94036 M5x5mm Set Screw
.....x1
35225 1st Spur Gear Holder (One-Way)
Anti-Clockwise
35248 1st Spur Gear (48T) 35230 8x12mm Flange Ball Bearing .....x2
Rotate Direction
ew t Scermen C
35230 8x12mm Flange Ball Bearing
35228 Alum. Nut
5x5mm Set Screw
Step 3
40112 2-Speed Shaft
* Place the set screw in the "D" cut.
35234 2nd Spur Gear Clutch Bell Step 2
35244 2nd Spur Gear (44T)
*Put the clutch shoe carrier to the edge of the groove on the shaft.
35219 Alum. Nut * Push the flange ballbearing into clutch bell. Clockwise Rotate Direction
6
18 ASSEMBLY OF THE TWO SPEED TRANSMISSION
Step 1 94036 5X5mm Set Screw
NO.7 3x15mm Hex Screw
3mm Nylon Nut
35237 Spring
.....x2
Step 2 36053 8x16x5mm Ball Bearing
35236 Clutch Shoe
40120 Brake Cap Joint Scre w Cem ent
BAG
*Screw the 3x15mm screw into the bottom and back off 5 turns. 3x15mm Screw
35237 6X6mm Set Screw
Ensure Free Movement
3x15mm Screw 35237 6X6mm Set Screw
5X5mm Set Screw
.....x2
35237 4mm Ball
35237 4mm Ball 94041 3mm Nylon Nut
.....x2
35237 4mm Ball
2nd Gear Assembly
40120 Brake Cap Joint
35237 Spring
3mm Nylon Nut
.....x2
94005 3x16mm Hex Screw
36053 8x16x5mm Ball Bearing
35236 Clutch Shoe
5X4mm Set Screw
w t re e n Sc em C
3x15mm Hex Screw
35237 6X6mm Set Screw
1st Gear Assembly
.....x2
7 THE CENTER MOUNT 19 ASSEMBLY OF THE TWO SPEED TRANSMISSION INTO 3x10mm Hex Screw
BAG
NO.7
Step 1
3x10mm Hex Screw
Step 2 40040 Center Diff. Mount
30212 5x8mm Flange Bearing
94003 3x10mm Hex Screw
40719 Center Diff. Mount Plate
.....x1
30212 5x8mm Flange Bearing
.....x4
40547 Brake Cam
40040 Center Diff. Mount
40512 Center Diff. Mount Post
20 ASSEMBLY OF THE BRAKE AND CENTER DIFF. MOUNT
BAG
4x4mm Set Screw
NO.7 3x3mm Set Screw
S r ew Cecm ent
94033 3x3mm Set Screw
.....x1
94034 4x4mm Set Screw
.....x2
30171 Brake Lever
Do Not Over Tighten
*Leave a 1.5 mm space between the two brake pads.
40714 Center Carry Handle 1.5mm
94011 3x16mm Hex Screw
.....x2
36659 Brake Pad
3x15mm Hex Screw
49009 CNC Brake Disk 36659 Brake Pad
*Insert the brake disc into brake cap joint before assembly.
21 ASSEMBLY OF THE ARM HOLDER ONTO CHASSIS *set the arm holder adjuster to the same direction.
BAG
NO.4 NO.5
A
A (Type A)
40748 Chassis
*set the arm holder adjuster to the same direction. 94027 4x16mm Flat Head Hex Screw
A
40719 Arm Holder Adjuster
A (Type A)
.....x8
4x16mm Flat Head Hex Screw
40719 Arm Holder (Front/Rear)
40719 Arm Holder (Rear/Rear)
40719 Arm Holder (Front/Front)
40719 Arm Holder Adjuster 40719 Arm Holder (Rear/Front)
4x16mm Flat Head Hex Screw
8
22 ASSEMBLY OF THE FRONT LOWER ARMS
Assembly of the right and left hand side are the same.
Step 2
NO.6
BAG
Step 1 40717 Front Lower Arm 4x10mm Set Screw 94035 3x8mm Set Screw
36870 4x10mm Set Screw
.....x2
40719 Stabilizer mount 40719 Stabilizer Balance Adjuster
31308 Stabilizer
.....x2 40711 4mm Arm Shaft
3x8mm Set Screw 94005 3x16mm Hex Screw
.....x2
94006 3x18mm Hex Screw
.....x4
*A 3x8mm set screw is use for thighten or loose stabilizer.
3x18mm Hex Screw
40711 4mm Arm Shaft
(Left Side) 2mm
*Keep stabilizer ball in the center. Turn stabilizer adjuster to adjust the stabilizer to the same angle.
Adjuster Center
23 ASSEMBLY OF THE REAR LOWER ARMS Step 2
NO.6
BAG
Assembly of the right and left hand side are the same.
4x10mm Set Screw
Step 1 40719 Stabilizer mount 94035 3x8mm Set Screw
.....x2
40717 Rear Lower Arm
40719 Stabilizer Balance Adjuster
40711 4mm Arm Shaft 36870 4x10mm Set Screw
31308 Stabilizer 3x8mm Set Screw
.....x2 3x18mm Hex Screw
94005 3x15mm Hex Screw
.....x2
94006 3x18mm Hex Screw
.....x4
40717 Rear Lower Arm 31308 Stabilizer
*Keep stabilizer ball in the center. Turn stabilizer adjuster to adjust the stabilizer to the same angle.
40719 Stabilizer Balance Adjuster
4x10mm Set Screw
3x18mm Hex Screw
2mm
40719 Stabilizer mount 3x8mm Set Screw
Adjuster Center
24 ASSEMBLY OF THE FRONT AND REAR GEAR BOX ONTO THE CHASSIS NO.3 NO.5 NO.6
BAG
Step 2 3mm Nylon Nut
Step 1
94041 3mm Nylon Nut
94020 3x12mm Flat Head Hex Screw
94026 4x12mm Flat Head Hex Screw
Front Gear Box Assembly .....x4
3mm
.....x4
.....x2 3x12mm Hex Screw
4x16mm Flat Head Hex Screw 94027 4x16mm Flat Head Hex Screw
3x12mm 4x16mm
4x10mm Flat Head Hex Screw .....x8
25 ASSEMBLY OF THE FRONT KNUCKLE ARMS
Assembly of the right and left hand side are the same.
NO.6
BAG
*Notice the direction of the plastic washer.
Step 1 40718 Ball type Knuckle Arm(left)
Ensure Free Movement
L
94049 2.6x8mm Cap Screw
36903 14mm Steering Ball .....x8
40718 Plastic Washer 36904 12mm Alum. Nut
36904 14mm Alum. Nut
.....x4
Ensure Free Movement
36903 14mm Steering Ball
36903 12mm Steering Ball
Do Not Over Tighten
40718 Plastic Washer 36904 12mm Alum. Nut
.....x4
26 ASSEMBLY OF THE FRONT KNUCKLE AND FRONT SUSPENSION ARMS
BAG
Step 1 ..........X2
94034 4X4mm Set Screw
..........X2
94021 3x56mm Flat Head Hex Screw
..........X2
Step 2 *Put the drive shaft into cap joint before assembly.
36053 8x16mm Ball Bearing
36053 8x16mm Ball Bearing
36055 2.5x16.8mm Pin
36055 2.5x16.8mm Pin ..........X2
36053 8x16mm Ball Bearing ..........X4
3x56mm Flat Head Hex Screw
40521 Universal Joint (Front)
Scr Cemeew nt
94041 3mm Nylon Nut
NO.3 NO.6 NO.12
Assembly of the right and left hand side are the same.
5x4mm Set Screw
40724 Dust Boot Bushing 40126 3X6mm Flange Washer
40526 Alum Wheel Hub 3mm Nylon Nut
40724 Dust Boot Bushing
27 ASSEMBLY OF THE FRONT PUSH RODS
Assembly for both right and left side.
Step 1
Step 2
3x12mm
30403 30403 6mm Ball
.....x4
94004 3x12mm Hex Screw
40712
40063 .....x2
40063 94007 3x20mm Hex Screw
.....x2
30403
1:1 Approx. 34mm
3x20mm
28 ASSEMBLY OF THE REAR WHEEL HUB
Assembly for both right and left side.
Step 1
Step 2 36082
94036 5x4mm Set Screw 36055 2.5x16.8mm Pin
.....x2
31304 .....x2 36055 36053 36053
40526
.....x4 Ensure Free Movement
31307 31307 11mm Steering Ball
Scr Cm e ew en t
36053 8x16mm Ball Bearing
8x12x1mm
31305 5x4mm
.....x4 Do Not Over Tighten
31306
29 ASSEMBLY OF THE REAR SUSPENSION ARMS
Assembly for both right and left side.
*When assembling the steering balls into the arms,leave about one threads for the rear arm ,and leaveno room for front arm. 94041 3mm Nylon Nut
.....x2
94008 3x25mm Hex Screw
.....x2
(Front)
(Rear)
3mm
2.5mm Allen Wrench
34028 *Insert the drive shaft before assembly. 3x25mm
30 ASSEMBLY OF THE REAR SHOCK ABSORBER
Assembly for both right and left side. 3x25mm
94040 3x8mm Washer
.....x2
94041 3mm Nylon Nut
.....x2 40531 40643 3x8mm 3mm
40531 Shock Ball End Post
.....x2
94007 3x20mm Hex Screw
.....x2
90018 3x25mm Cap Screw
.....x2
3x20mm
31 ASSEMBLY OF THE TWO SPEED TRANSMISSION ONTO THE CHASSIS 40749
* Insert drive shaft into cap joint before assembly two speed onto chassis. 94026 4x12mm Flat Head Hex Screw
.....x4 40749
Sc re w Cem ent
4x10mm
32 ASSEMBLY OF THE CLUTCH BAG
NO.10 Step 1
Step 2
* Only use the 10091 pilot shaft for threaded crank shaft engine. 10091 Pilot Shaft (Not Included)
rew nt Sceme C
Threaded Crank Shaft
10330 Tapper Corn
*Place the clutch shoes with the clutch springs over the 3 pins of the flywheel. *Using a phillips screw driver or needle nose pliers and bend the small end lf the clutch spring behind the pilot shaft #174D or #180D than press down.
10101 Clutch Spring
40573 3 Pin Flywheel (35mm)
40573 3 Pin Flywheel (35mm)
SG Type Crank Shaft Engine
10010 Clutch Shoes
S Cecre m w en t
10330 7mml Tapper Corn
*Fit the flywheel using a pair of the plier and cross wrench.
10098 SG Clutch Nut Engine rotation direction. Tighten
33 ASSEMBLY OF THE CLUTCH NO.10
BAG
Step 1
10099 3x7mm Washer
.....x1
10099 5x8x0.3mm Washer
.....x3
35255 20T-2nd Clutch Gear
w t re en Sc em C
35958 5x8mm Ball Bearing
Step 3
34110 5x10x4mm Ball Bearing
35242 Clutch Bell
35958 5x8mm Ball Bearing
.....x1
10099 5x8x0.3mm Washer
Step 2 S Ce cr m ew en t
34110 5x10x4mm Ball Bearing
10099 3x7mm Washer 10099 3x5mm Cap Screw
.....x1
w t re en Sc em C
10099 3x5mm Cap Screw
.....x1
34 ASSEMBLY OF THE MANIFOLD AND MUFFLER
3x12mm Cap Screw
Manifold(Option)
Not Included
NO.10
BAG
Screw Cement
Step 1
94038 3x12mm Cap Screw
*Adjust the backlash with the washer.
35240 16T-1st Clutch Gear
Step 2
Not Included 97501 1/8 Silicone Seal(Option)
.....x4
*The muffler and manifold may not be included in some kit.
97501 1/8 Spring
Muffler(Option)
Not Included
40574 Low Profile Engine Mount
Not Included
35 ASSEMBLY OF THE ENGINE ONTO THE CHASSIS 3x12mm Step 1
Step 2 Note book Paper.
94038 3x12mm Cap Screw
3x5mm Spring Washer
.....x4
3x5mm Spring Washer
*Use note book paper to set gear backlash between spur gear and clutch bell gear, applying pressure while retightening the engine. *If the space is not correct the spur gear will be damaged.
10114 5mm Engine Mount Screw .....x4
ew Scerment C
10114 40574
37 ASSEMBLY OF THE MANIFOLD ONTO THE ENGINE Step 1 94034 4x4mm Set Screw
Step 2
*The muffler and manifold may not included from different kit.
.....x1 Manifold(Option)
94036 5x4mm Set Screw
.....x1
1/8 Spring(Option) 94026 4x12mm Flat Head Hex Screw
.....x1
10069
Not Included
10120
1/8 Silicone Seal(Option)
4x4mm
ew t Scermen C
5x4mm S r ew Cecm e nt
Muffler(Option)
41050
10052
4x10mm
39 ASSEMBLY OF THE FUEL TANK ONTO THE CHASSIS 12 NO.3 NO.11
BAG
3x10mm Hex Screw
Step 1
Step 2
40543 Fuel Tank
Do Not Over Tighten
94019 3x10mm Flat Head Hex Screw
.....x2
94003 3x10mm Hex Screw
.....x2
Pressure Nipple
Do Not Over Tighten
40539 Fuel Tank Post
3x10mm Flat Head Hex Screw
40 ASSEMBLY OF THE RADIO TRAY BAG
Step 1
NO.9
34026 Servo Washer
40715 Alum. Throttle Pivot Post
Step 3
Step 2 3x8mm Hex Screw
40709 Alum. Radio Tray
3x8mm Washer
34026 Servo Mount Throttle Servo
3x8mm Hex Screw 3x16mm Hex Screw w t re e n Sc em C
94040 3x8mm Washer
94002 3X8mm Hex Screw
Put the protector rubber onto your servo.
34026 Servo Washer
.....X8
.....X7
40541 Radio Tray Post ( Plastic )
34026 Servo Mount Steering Servo
94005 3x16mm Hex Screw
.....X8
3x16mm Hex Screw
3x8mm Washer
3x8mm Hex Screw
41 ASSEMBLY OF THE RADIO TRAY AND RECEIVER BOX *Put the servo wire into receiver box and connect to receiver.
NO.9
BAG
Antenna 2X8mm Screw
Step 1
Step 2 30560 Antenna Pipe
2X8mm Screw
94002 3X8mm Hex Screw
40541 Receiver Box
.....X4
40541 Receiver Box Cover
40541 Receiver Box Cover
.....X2
*Use the original battery case or rechargeable hump pack battery.
40642 Antenna Pipe Fixing Nut
*Connect the switch wire to receiver.
*Connect battery wire to switch. 37410 Clips
10280 Switch Cover Switch
Battery
40580 Protective Foam for Receiver Box
40541 Switch holder
3X8mm Hex Screw *Use the screw provided with your switch
40580 Protective Foam for Receiver Box
40541 Receiver Box
Servo Wire
Receiver
42 ASSEMBLY OF THE THROTTLE LINKAGE 3x5mm Hex Screw Tighten BAG
NO.9 Step 1
3x3mm Set Screw
3x10mm Hex Screw
30800 Adjust Mount
.....x3
94033 3x3mm Set Screw
.....x3
3x8mm Washer
35958 5x8x2.5mm Ball Bearing
2.6x10mm Cap Screw Tighten
3x3mm Set Screw
10300 Alum Stopper
30800 2mm Adjust nut 30800 Adjust Mount
Ensure Free Movement 94003 3x10mm Hex Screw
Step 2
30172 2X68mm Brake Rod
30531 Throttle Spring
3x3mm Set Screw 30800 2.6x6mm Washer
30800 Throttle Ball End
10300 Alum Stopper
2.6x6mm Washer
.....x1
Completely Finished 40719 Servo Horn
94050 2.6x10mm Cap Screw
.....x1 37360 4mm Ball & Socket
43 ASSEMBLY OF THE THROTTLE LINKAGE INTO SERVO A
BAG
94035 3x8mm Set Screw
.....x1
NO.9
Cut off the servo saver as shown.
37650 4mm Ball End(Short)
A'
Parallel
3x8mm Set Screw 30403 6mm Ball End
.....x2 37650 4mm Ball End(Long)
*Ensure that servo gears are centered before attaching the servo horns. The best way to accomplish this is by connecting the servos to the radio system and setting the trim to the center.
*Use the screw provided with your servo.
37360 4mm Ball & Socket
10765 Servo Horn
10765 Servo Horn Adapter Sanwa/Airtronics
S
JR
J
Futaba
F
HiTech
H
* Choose the right servo horn adapter for your servo.
44 ASSEMBLY OF THE STEERING ROD AND RADIO TRAY ONTO THE CHASSIS Step 1
30403 6mm Ball End
94019 3x10mm Flat Head Hex Screw
.....x1
Step 2
NO.9
BAG
*Use the screw provided with your servo.
3x3mm Set Screw
10300 Alum Stopper
30403 6mm Ball 3X12mm Hex Screw 30403 6mm Ball
10765 Servo Horn Adapter
.....x8
10765 Servo Horn 94004 3X12mm Hex Screw
*Snap on.
30401 Plastic Ball End
40713 3x64mm Turnbuckle
.....x1
1:1
3x10mm Flat Head Hex Screw
Approx. 49 mm ¬ 4 9 mù 30401 Plastic Ball End
3X12mm Hex Screw
3x10mm Flat Head Hex Screw
.....x2
45 ASSEMBLY OF THE FRONT BUMPER
BAG
NO.8 40721 Front Bumper Post
94026 4x12mm Flat Head Hex Screw
94020 3x12mm Flat Head Hex Screw
94042 4mm Nylon Nut
40721 Front Bumper Post
4mm Nylon Nut .....x3
40721 Front Bumper
.....x2
.....x3
Tighten 4x12mm Flat Head Hex Screw
3x12mm Flat Head Hex Screw Tighten
46 ASSEMBLY OF THE FRONT BUMPER BAG
Completely Finished 40117 Body Post
4x10mm Set Screw
NO.8 Step 1
Step 2 40720 Body Post
36870 4x10mm Set Screw
.....x2 40117 Body Post
94026 4x12mm Flat Head Hex Screw
.....x2
40721 Front Bumper Top Plate
31159 Body Clip
Approx. 4 mm ｬ4mm * The 4x10mm set screw is used to adjust down stop.
Tighten 4x12mm Flat Head Hex Screw Tighten
47 ASSEMBLY OF THE FRONT AND REAR BUMPER BAG
NO.8 4x10mm Hex Screw
3x12mm Flat Head Hex Screw
94042 4mm Nylon Nut
40721 .....x2
4mm 40725 Foam Bumper 94009 4x10mm Hex Screw
94020 3x12mm Flat Head Hex Screw
40721 .....x2
Tighten
.....x4
Tighten 94026 4x12mm Flat Head Hex Screw
4x12mm .....x2
3x12mm
48 ASSEMBLY OF THE BOOY AND PAINTNG. Cut out the body as shown.
31138 Body(Option)
Use a neutral detergent to remove any dirt and oil.
Cut Out
Before cutting and making holes on the body, put the unpainted body on the chassis to confirm the mounting position and location for holes and cutouts.
Mask the windows from the inside with masking tape.
Body Reamer (Not included.)
Making two holes on the front and two holes on the rear for body posts.
9mm
9mm
Paint the body with polycarbonate spray paints.
Spray Paint
49 ASSEMBLY OF THE ONTO FRONT KNUCKLE AND REAR HUB
Doubleside Tape
Nylon Screw Do Not Over Tighten
Step 1
Step 2
Doubleside Tape
Side Plate
Take off the doubleside paper before assembly. Cut Out
Side Plate
Nylon Nut
50 ASSEMBLY OF THE AIR FILTER NO.11
BAG
*Apply filter oil to the foam before use.
Connect to carburetor.
38400 Air Filter
10179 Fuel Tube
Connect to fuel tank.
Nylon Strap
Connect to pressure nipple.
Connect to fuel tank pressure nipple.
*Notice the direction and make two lift and right hand side tires are the same. *Check the rotation direction before gluing.
51 ASSEMBLY OF THE TIRES AND WHEELS (Right Hand Side) *Notice the direction of the tires. Make two the same for the left and 2 for the right. Check the rotation direction before gluing.
(Left Hand Side) *Notice the direction of the tires.
*Notice the direction of the tires.
86052 Tire
Contact Adhesive Contact Adhesive Contact Adhesive Contact Adhesive
86023 Wheel 86059 Inner Sponge (WidE) 86059 Inner Sponge (Narrow)
*Pull back the tire bead slightly and spot glue in four spots as shown. When dry, glue the rest of the wheel between the spots. Repeat the procedure on the other side of the wheel until fully glued.
INS TA GLUNT E
52 ASSEMBLY OF THE WHEELS ONTO THE FRONT KNUCKLE AND REAR HUB
Step 1
Assembly for both right and left side.
40550
40550 40550 Wheel Nut
.....x4
*Notice the direction of the tire pattern.
40550 *Tire and Wheel assembly.
40550
53 MOUNTING BODY 31159
31159
54 STARTING OF THE ENGINE How to start the engine: 1. 2. 3. 4.
Turn on transmitter and then receiver. Fill fuel tank with fuel bottle. Connect 1.2V glow plug igniter . Start engine with a 12V starter. ( Notice the direction of the starter.) 5. After the engine has started, remove the 1.2V glow plug igniter .
A 12V Starter Box ( Not Included)
Glow Plug (Not Included) 51007
Normal Plug
1.2V Glow Plug Igniter and Charger (Not Included)
10215 - Glow Heater, Extra Long W/Charger.
51006
* Follow the engine manufacturer instruction manuals regarding engine set-up, carburetor and maintenance.
Turbo Plug
10250 - Starter Box 1/8 scale On/Off-Road.
*There are 2 types of glow plugs available"NORMAL" or "Turbo" depending on the type of the engine.
*To start the car, attach a glow plug igniter to the glow plug, and use either a 12V electric starter or starter box applied to the flywheel exposed through the chassis.
1.2V
1.2V
*Applied to the flywheel exposed through the chassis.
Starter Box (Not Included)
ADJUSTING THE SHIFT POINT SHIFT UP TIMING ADJUSTMENT
Adjust the engine before adjusting the clutch shift timing. Adjust the engine as per engine instruction manual.
1. Once the engine adjustments have been completed, proceed to the adjustment of the clutch shoe shift timing. (Using a 2mm allen wrench to adjust the clutch shoe on either side.) 2mm Allen Wrench
3x15mm Hex Screw
Note: Clockwise--------Shift timing will become later. Counterclockwise---Shift timing will become quicker. 2. Adjust the clutch shift timing for your track conditions. As you tighten (Clockwise) the 3x15mm screw, the shift timing will become slower. As you loosen (Counterclockwise ) the 3x15mm screw, the shift timing will become quicker.
Clockwise (Tighten)
Anti-clockwise (Loosen)
3. Set the shift timing to the track conditions while the car is running.
2 SPEED GEAR RATION COMBINATIONS 6x6mm Set Screw
3x15mm Hex Screw
2 speed transmission allows the car to have more punch out of the corners and higher top speed. We offer many different pinion and spur gear combinations which can be used for different tracks. Spur Gear
Clutch Gear (4 tooth different) 15T-19T
49T/45T 48T/44T
21
16T-20T
17T-21T
Torque
Speed
SETTING GUIDE FRONT TOE-IN AND TOE-OUT SETTING
Use a 2.5mm allen wrench to adjust toe-in for front and rear. (Front) Adjust the length of the front steering rod to change the toe angle.
NEUTRAL POSITION
Making the steering rod longer will make the front tires become toe-in. Response will be slower and will over steer.
TOE-IN TOE-OUT
TOE-OUT
Making the steering rod shorter will make the front tires become toe-out. Response will be quicker and will under steer. We recommended adjusting the front toe-out to 1.5 degrees. (Rear) Adjust the length of the rear hub (12mm ball/rear) to change the toe angle. Making the 12mm ball longer will make the rear tires toe-in. Response will be under steer. Making the 12mm ball shorter will make the rear tires toe-out. Response will be over steer. We recommended adjusting the rear toe-in to 2 degrees.
Steering Rod
REAR TOE-IN
REAR TOE-IN
2.5mm Allen Wrench
FRONT AND REAR CAMBER ANGLE SETTING
*Use 2.5mm hex wrench to adjust upper arm ball in front.
Note: Place the model car on a flat surface. Raise the chassis to it's maximum clearance before the wheels leave the ground. Adjust the length of the front and rear upper arms so that the wheels are right angles to the ground.
(REAR)
(FRONT)
+ Positive
-
-
+
+ Positive
Negative
-
-
Negative
+
Turnbuckle
Adjust the length of the turnbuckle on the rear upper arms can be change the rear camber. We suggest using 2 degress of negative camber for the rear.
The front camber adjustment can be made by moving the 14mm steering ball at the front upper arms on knuckles, clockwise or anticlockwise. We suggest using 1.5 degress of negative camber for the front.
FRONT AND REAR SHOCK ANGLE SETTING 1 2
Firm
Soft
Soft
(FRONT)
1234
(REAR)
Firm
Soft Firm front suspension, less steering. Soft front suspension, more steering.
12
Firm
Soft Firm rear suspension, over steering. Soft rear suspension, under steering.
12
Firm
3 4 3 0 3 D M 1-S P E C P R O P A R T S LIS T OFNA 10010 10040 10052 10069 10098 10101 10114 10120 10179 10185 10270 10282 10300 10330 10765 30171 30172 30212 30401 30401 30403 30531 30560 30773 30776 30800 30800 31159 31304 31305 31306 31307 31308 31991 31994 34026 34028 34110
D e s c r ip tio n 3 S h o e C lu t c h c a r b o n 3 P in F ly w h e e l . 2 1 C o r n T y p e S p r in g M u f f le r S t a y E x h a u s t C o n n e c to r P ilo t S h a f t , S G T y p e C lu t c h S p r in g E n g in e M o u n t S c r e w , 5 m m H e x M a n if o ld S p r in g F u e l T u b e (4 5 c m ) S ilic o n e J o in t T u b e B la c k F u e l T u b e C lip s S w it c h C o v e r , B la c k A lu m . S t o p p e r C o n e , 7 m m B ra s s T a p p e r U n iv e r s a l S e r v o H o r n B ra k e L e v e r B ra k e R o d 5 x 8 x 2 . 5 F r a n g e B e a r in g 6 m m B a ll E n d ( P la s tic ) P la s tic P a r t s S e t f o r D a m p e r 6 m m B a ll & S o c k e t T h r o t t le S p r in g A n t e n n a P ip e 4 m m C r o s s P in 4 x 1 0 x 0 .2 W a s h e r 2 m m B r a k e A d ju s t N u t T h r o t t le L in k a g e P la s tic B o d y C lip s R e a r H u b ( B a ll T y p e ) P la s tic W a s h e r f o r B a ll 1 2 m m A lu m . H e x S c r e w 1 1 m m B a ll & S c r e w S t a b liz e r ( S t e e l) ( L & R ) M a n if o ld , 2 1 W / S p r in g , P o lis h e d P ip e , 9 . 5 m m D M - 1 R T R P o lis h e d S e r v o F ix in g ( L a y d o w n ) D o g B o n e , 1 0 0 m m , U L T R A X -1 B a ll B e a r in g 5 X 1 0 X 4
35219 35225 35228 35230 35234 35235 35236 35237 35237 35237 35240 35242 35244 35248 35255 35958 36053 36055 36660 36661 36700 36742 36790 36850 36861 36903 36904 37360 37410 37650 38400 40009 40010 40011 40024 40034 40037 40038 40040 40042 40044 40060
A lu m . N u t (c lo c k w is e ) 1 s t S p u r G e a r H o ld e r (o n e -w a y) A lu m . N u t (a n ti-c lo c k w is e ) 8 x 1 2 F la n g e B e a rin g 2 n d S p u r G e a r C lu tc h B e ll C lu tc n S h o e C a rrie r C lu tc h S h o e S p rin g 4 m m B a ll 6 x 6 m m S e t S c re w C lu tc h G e a r (1 s t) 1 6 T C lu tc h B e ll 44T 2nd Spur G ear 48T 1st Spur G ear C lu tc h G e a r (2 n d ) 2 0 T 5 x 8 x 2 .5 B a ll B e a rin g 8 x 1 6 B a ll B e a rin g 2 .5 x 1 7 P in s B ra k e P a d s , 4 P C S . B ra k e P a d W a s h e rs , 4 P C S . S te e rin g 7 m m B a ll S e rv o S a v e r B u s h in g 4 x 4 6 T u rn b u c k le 7 m m B a ll 5 x 3 5 T u rn b u c k le S te e rin g B a ll 1 4 m m 1 4 m m A lu m . N u t 4 m m B a ll & S o c k e t B o d y P in (S ) 4 m m P la s tic B a ll J o in t 1 /1 0 A ir F ilte r P -6 O -R in g 2 .5 x 1 3 .8 p in D iff. G a s k e ts D iff B e v e l G e a r S h im 1 3 x 1 6 x 0 .2 m m A lu m . S e rv o S a v e r R in g A d ju s te r S te e rin g P la te H e x S c re w s 7 m m B a lls (B la c k ) C e n te r D iff M o u n t (p la s tic ) B ra k e D is c s , S te e l 4 P c s . S p rin g , B ra k e S e p e ra to rs , 8 P c s . M 2 .5 N ylo n N u t
R E T A IL 1 3 .9 5 1 4 .9 5 4 .9 5 6 .9 5 4 .9 5 4 .9 5 7 .9 5 4 .9 5 1 .9 5 4 .9 5 3 .9 5 3 .9 5 4 .9 5 2 .9 5 8 .9 5 1 .9 5 1 .5 0 5 .9 5 2 .9 5 2 .9 5 4 .9 5 2 .9 5 2 .9 5 3 .9 5 1 .9 5 6 .9 5 6 .9 5 4 .9 5 1 0 .9 5 8 .9 5 8 .9 5 8 .9 5 1 0 .9 5 2 5 .9 5 5 4 .9 5 7 .9 5 1 5 .9 5 6 .9 5
OFNA 40065 40073 40074 40090 40112 40117 40120 40126 40500 40511 40512 40513 40514 40516 40517 40519 40521 40522 40525 40526 40531 40533 40537 40538 40539 40541 40543 40546 40547 40548 40549 40550 40560 40563 40568 40580 40633 40634
D e s c r ip tio n R e a r U p p e r B a ll E n d B e a r in g , 4 x 8 F la n g e 6 x 1 0 B a ll B e a r in g S h o c k R e p a ir K it 2 -S p e e d S h a ft 1 /8 T ru c k B o d y M o u n t 8 m m C a p J o in t f o r B r a k e 3 x 6 x 2 . 5 F la n g e W a s h e r S e r v o S a v e r S p r in g ( B la c k ) S e rv o S a v e r P o s t C e n t e r D if f . M o u n t P o s t D if f . G e a r ( s m a ll & la r g e ) C a p J o in t f o r D if f . S t e e l B e v e l G e a r 1 3 T ( S m a ll) S te e l B e v e l G e a r 4 3 T (L a rg e ) C a p J o in t U n iv e r s a l J o in t , F r o n t R e a r D r iv e S h a f t R e a r L o w e r A r m S h a f t ( 3 x 4 8 .1 m m ) 17m m W heel H ub S h o c k B a ll E n d P o s t/ o n e - p ie c e /T o p G ear C ase F ro n t U p p e r A rm s D if f . C a s e ( F & R ) S e rv o S a v e r & C e n te r B ra c e r R e c e iv e r B o x Fuel Tank F r o n t A r m S h a f t 3 x 4 2 .7 m m B ra k e C a m M 3 N y lo n N u t ( T h in T y p e ) M u f f le r S t a y 17m m W heel N ut S e r v o S a v e r C o n n e c tin g P la t e A lu m . S e r v o S a v e r T u b e G r a p h it e F r o n t P la t e P r o t e c t F o a m f o r R e c e iv e r B o x Shock Cap, 13m m S h o c k S p r in g A d ju s te r
2 .9 5 2 6 .9 5 2 .9 5 1 2 .9 5 2 4 .9 5 5 .9 5 1 4 .9 5 9 .9 5 9 .9 5 9 .9 5 1 1 .9 5 2 4 .9 5 7 .9 5 7 .9 5 1 1 .9 5 3 .9 5 1 2 .9 5 3 .9 5 3 .9 5 3 .9 5 6 .9 5 1 .9 5 1 0 .9 5 3 .9 5 6 .9 5 7 .9 5 9 .9 5 4 .9 5 3 .9 5 6 .9 5 9 .9 5 2 .9 5 2 .9 5 3 .9 5 2 .9 5 5 .9 5 5 .9 5 9 .9 5 4 .9 5 1 0 .9 5 5 .9 5 4 .9 5
40635 40636 40637 40638 40640 40642 40643 40674 40694 40708 40709 40710 40711 40712 40713 40714 40715 40716 40717 40718 40719 40720 40721 40722 40723 40724 40725 40731 40734 40735 40736 40737 40738 40745 40746 40748 40749 40750 40751 86023 86052 86059
S h o c k S h a ft D u s t C o v e rs 1 5 x 1 O -R in g D u s t F e lt fo r S h o c k A b s o rb e r S h o c k P is to n , 1 3 m m S h o c k P re s s u re T o p , O ra n g e A n te n n a P ip e F ix in g N u t P la s tic S h o c k P a rts S e t E n g in e M o u n t T a ll F o r P u lls ta rt C N C 7 0 7 5 C h a s s is B ra c e , F & R C h a s s is 6 0 6 1 D M 1 R T R R a d io T ra y A lu m . D M 1 R T R C e n te r D riv e S h a ft 1 2 0 m m 4 x 9 0 m m A rm S h a ft 3 .5 x 4 8 m m T u rn b u c k le 3 x 6 4 m m T u rn b u c k le C e n te r H a n d le B a r T h ro ttle C o n n e c tin g A lu m . P o s t R e a r U p p e r A rm s F ro n t & R e a r L o w e r A rm s B a ll T yp e K n u c k le A rm s (L & R ) A rm H o ld e r P la s tic B o d y S id e B u m p e r F ro n t & R e a r B u m p e r E x h a u s t C o n n e c te r D u s t P ro o f C o v e r R u b b e r B u s h in g fo r H e x S c re w Foam Bum per C N C A lu m S h o c k S ta y, F W in g & W in g S ta y U n it R e a l M u ffle r & B a c k M irro r D M -1 S h o c k S h a ft S h o c k B o d y, 1 3 m m D M -1 S h o c k S p rin g F ro n t (R e d ), S o ft A lu m . F ro n t P la te B la c k A lu m . S e rv o S a v e r C n t. P la te B la c k C H A S S IS , 6 0 6 1 D M 1 S P E C C E N T E R D R S H F T D M 1 S 8 8 .5 /1 0 4 m m SH O C K T O W ER R R ALU M D M 1 SPEC S P R IN G S , R E A R R E D D M 1 S P E C 1 /8 M e s h W h e e ls (B la c k ) 1 /8 R a d ia l T ire G T P In n e r S p o n g e (L & S )
R E T A IL 4 .9 5 1 2 .9 5 1 7 .9 5 7 .9 5 9 .9 5 1 0 .9 5 1 1 .9 5 3 .9 5 3 .9 5 6 .9 5 1 3 .9 5 1 6 .9 5 1 3 .9 5 1 4 .9 5 3 8 .9 5 9 .9 5 4 4 .9 5 1 9 .9 5 6 .9 5 1 1 .9 5 9 .9 5 1 1 .9 5 6 .9 5 9 .9 5 1 1 .9 5 1 4 .9 5 1 6 .9 5 1 1 .9 5 8 .9 5 1 .9 5 4 .9 5 4 .9 5 1 2 .5 0 9 .9 5 3 1 .9 5 1 .9 5 1 8 .9 5 9 .9 5
5 .9 5 3 .9 5 1 .9 5 7 .9 5 5 .9 5 2 .9 5 9 .9 5 1 8 .9 5 5 9 .9 5 8 9 .9 5 1 2 .9 5 1 9 .9 5 7 .9 5 9 .9 5 9 .9 5 3 .9 5 7 .9 5 9 .9 5 1 9 .9 5 1 9 .9 5 1 5 .9 5 9 .9 5 1 9 .9 5 7 .9 5 7 .9 5 4 .9 5 1 4 .9 5 3 9 .9 5 1 2 .9 5 1 4 .9 5 7 .9 5 2 4 .9 5 1 4 .9 5 7 .9 5 9 .9 5 9 9 .9 5 1 9 .9 5 1 4 .9 5 9 .9 5 1 9 .9 5 1 9 .9 5 9 .9 5
OWNER’S REGISTRATION CARD OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment. The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date. In the event that the kit is incomplete or component parts are broken due to error in manufacturer, contact your dealer from which you purchased the kit for replacement part or call OFNA at (949) 586-2910 for your nearest dealer location. Other items such as radio and engine other covered by individual warranties. IMPORTANT! Please print or type, filling in the information listed below and mail immediately
MAIL TO: OFNA RACING 7 VANDERBILT IRVINE, CA. 92618 TEL: (949) 586-2910
Write in Your Model Name and Part Number
REGISTRATION CARD
RACER’S NAME
TEL:(
)
ADDRESS
CITY
STATE
DEALER’S NAME
ZIP
TEL: (
ADDRESS
CITY
OFNA 7 Vanderbilt Irvine, Ca. 92618
STATE
ZIP
)
