Transcript
Easy, Reliable & Secure
Installation Guide
Po w e rl i n e 200 Plus H o me N etwor k Adap ter (P L 2 0 0 P )
Trademarks Brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, On Networks reserves the right to make changes to the products described in this document without notice. On Networks does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. This symbol is placed in accordance with the European Union Directive 2002/96 on the Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union, this product should be treated and recycled in accordance with the laws of your jurisdiction implementing the WEEE Directive. For indoor use only in all EU countries and Switzerland. ATTENTION: Due to EU law, the country settings must be identical to the country where the device is operating (important due to nonharmonized frequencies in the EU).
2
LED Descriptions Item
Description
Power LED
• Solid green. The electrical power is on. • Blinking green. The adapter is in the process of setting up security. • Off. There is no electrical power. • Solid green. The Ethernet port is linked. • Off. There is no Ethernet connection. • Solid green. Link rate > 80 Mbps. • Solid amber. Link rate > 50 Mbps and < 80 Mbps. • Solid Red. Link rate < 50 Mbps. • Off. The adapter has not found any other compatible Powerline devices using the same encryption key.
Ethernet LED
Performance Indicator
3
Button Descriptions Ethernet port
Security button Reset button
Item
Description
Factory Reset button
Press the Reset button for 1 second, then release it to return the Powerline adapter to its factory default settings. After you plug in your new AV adapter, press the Security button for 2 seconds, then press the Security button on one of the other AV adapters in your existing network for 2 seconds. Both buttons must be pressed within 2 minutes.
Security button
4
Install Your Powerline Adapter For each Powerline adapter you are adding to your existing Powerline network, do the following: 1.
Plug each Powerline adapter into a power outlet. 2. Set up security on your Powerline adapter to add it to your existing Powerline network. Press the Security button for 2 seconds, then press the Security button on one of the other Powerline adapters in your existing network for 2 seconds. Both buttons must be pressed within 2 minutes. Note: Do not press the Security button on the Powerline adapter until installation is complete and the adapters are communicating with each other (indicated by the blinking Powerline LED). Pressing this button too soon can temporarily disable Powerline communication. If this situation occurs, press the Reset button to return the Powerline adapter to its factory default settings.
5
3.
Connect devices to your Powerline adapter. You can connect a device, such as a router or a computer, to the Ethernet port on the bottom of the Powerline adapter.
Safety Information •
• •
•
•
For national approvals (approval schemes other than CB), relevant national standards for plug, socket-outlet, and direct plug-in units (for example, US) shall also be consulted while testing and approving such products according to national standards. AC input rating (NA): 100–125V, 0.2A (Max); 50–60Hz excluding socket outlet rating. AC input rating (AU, UK, FR, EU): 200–250V, 0.2A (Max), 50–60Hz excluding socket outlet rating. Model Number ratings (maximum load): EU: 16A 250V~, UK: 13A 250V~, FR: 16A, 250V~, NA: 12A 125V~, AU: 10A, 250V~. Operating temperature: 0–40° C.
6
•
• •
•
•
Check the electrical current for any device plugged into the filtered AC socket. Do not exceed home and product outlet ratings and electrical requirements. The socket-outlet must be installed near the equipment and be easily accessible. Only power cords are allowed to be inserted into the filtered AC outlet; no other equipment with a direct plug-in is allowed. Power cord needs to be a maximum of 1 m long and a minimum of 0.75 mm square of cross-sectional area. Do not plug devices into the PL200P filtered AC outlet that exceed the product ratings. The output voltage of the filtered AC outlet is the same as the power outlet that the PL200P is plugged into. To help avoid damaging your system, be sure that the attached devices are electrically rated to operate with the power available in your location. If the input AC voltage is less than 100 Vac, the device plugged into the filtered AC socket of the PL200P might not perform as well as expected. 7
•
DO NOT PLUG MAJOR HOME APPLIANCES into the filtered AC socket or into an attached powerstrip. The device is not intended to be used with home appliances, such as air conditioners, power tools, space heaters, fans, hair dryers, ovens, or refrigerators.
8
Technical Support Thank you for selecting On Networks products. After installing your device, locate the serial number on the label of your product, and use it to register your product at http://www.on-networks.com/register. Registration is required to use our telephone support service. For product updates and web support, go to http://www.on-networks.com/products/powerline. For complete DoC, visit http://www.on-networks.com/doc.
9
10
11
August 2012
