Transcript
One station Impact Printer Model: WP-300 Version : 1.03
WP-300 One Station Impact Printer INDEX 1. GENERAL SPECIFICATION ................................................................................... 2 1.1 DESCRIPTION ........................................................................................................ 2 1.2 CHARACTERISTICS ................................................................................................. 2 1.3 ACCESSORIES ....................................................................................................... 2 2. MAIN SPECIFICATION ........................................................................................... 3 3. ILLUSTRATION ....................................................................................................... 4 4. OPERATION ............................................................................................................ 5 4.1 CONNECTING POWER SUPPLY................................................................................. 5 4.2 CONNECTING CASH DRAWER .................................................................................. 5 4.3 INSTALLING RIBBON CASSETTE ............................................................................... 6 4.4 INSTALLING PAPER ROLL ........................................................................................ 7 5. CONTROL PANEL .................................................................................................. 9 5.1 BASIC OPERATION ................................................................................................. 9 5.2 STATUS ................................................................................................................. 9 5.3 TEST PATTERN OPERATING PROCEDURE ................................................................. 10 6. DIP-SWITCH SETTING ......................................................................................... 11 7. INTERFACE ........................................................................................................... 14 7.1 REPLACE INTERFACE ............................................................................................ 14 7.2 SERIAL INTERFACE ............................................................................................... 14 7.3 PARALLEL INTERFACE ........................................................................................... 15 8. CASH DRAWER OUT PUT ................................................................................... 17 8.1 SPECIFICATION .................................................................................................... 17 8.2 PIN ASSIGNMENT ................................................................................................. 17 8.3 CIRCUIT DIAGRAM ................................................................................................ 17 9. CODE TABLE ........................................................................................................ 18 9.1 CHINESE CHARACTER .......................................................................................... 18 9.2 INTERNATIONAL CHARACTER ................................................................................. 18 10. DIMENSION ......................................................................................................... 19
-1-
WP-300 One Station Impact Printer 1. General Specification 1.1 Description WP-300, one station impact printer, is applied to receipt printer, fiscal printer, computer peripheral and etc.
1.2 Characteristics (1). Printing Speed / 4.3 lines per second. (2). Interface USB, Serial Port and Centronic are available. (3). ESC/POS command compatible. (4). 16 Kbytes data receive buffer. (5). Containing 16 x 16 dots font, Traditional Chinese, Simple Chinese and Japanese are available. (6). Out put for two cash drawers. (7). 76mm and 58mm wide paper are available (8). Normal and black mark paper are available.
1.3 Accessories Following accessories are packed with the printer, please confirm. (1). WP-300 printer (2). Roll Paper (3). Ribbon (4). Power Supply (5). User’s Manual (6). Power Core (7). Cable
-2-
WP-300 One Station Impact Printer 2. Main Specification NO Item
Description
1
Printing method
9-pin serial impact dot matrix
2
Printing direction
Bi-direction printing and logical seeking
3
Printing speed
4.4 lines / sec
4
Command
ESC/POS
5
Driver
Windows and OPOS
6 Character structure 7
Columns
76mm/58mm
8
Character size
9
Fonts
10 Detectors 11 Paper 12 Paper size
Font A
Font B
Kanji
7×7
9×7
16×16
42 /34Columns
35/28 Columns
21/17 Columns
1.99(W)×1.88(H)
1.53(W)×1.88(H)
2.53(W)×2.95(H)
Multilingual code page*12, Chinese, Japanese, Korean and Others Paper end (Black Mark), Paper near end, cover, Cutter jam and Head lock. 1 original + 1 copy (carbon) 76 mm
76 ± 0.5 (W) x 80 (D) mm(Dia.)
58 mm
58 ± 0.5 (W) x 80 (D) mm(Dia.)
13 Paper thickness
0.05 ~ 0.14 mm
14 Drawer output
2
15 Reliability
Head
100 million characters
Mechanism
MCBF: 10 million lines
Cutter
500,000 times
16 Receive buffer
16K bytes
17 Power supply
+24VDC / 2.5 A
18 Interface
RS-232C, Parallel, USB and Ethernet are optional
19 Gross weight
3.40Kg
20 Dimension
160(W) x 238(D) x 167(H) mm
21 temperature
22 Humidity
Operation
0° to 45 °
Storage
-10° to 50°
Operation
10 ~ 80 ％RH
Storage
10 ~ 90 ％RH
-3-
WP-300 One Station Impact Printer 3. Illustration
1
Top Cover
2
Paper Exit
3
Operation Panel
4
Mid-Housing
5
Power Switch
6
Bottom Housing
7
Dip-Switch Window
8
Interface
9
Power Supply Outlet
10 Cash Drawer Terminal
-4-
WP-300 One Station Impact Printer 4. Operation 4.1 Connecting Power Supply (1) Confirm the power is off. (2) Plug power supply into power supply outlet.
(3) Pin assignment as following Pin Number Description 1 +24VDC 2 GND 3 NC Shell Frame GND
4.2 Connecting Cash Drawer (1) Confirm the power is off. (2) Prepare RJ11 phone jack as right picture. (3) Plug RJ11 phone jack into cash drawer terminal.
Caution: The cash drawer specification must be +24VDC. If not for +24VDC, it may cause some damages.
-5-
WP-300 One Station Impact Printer 4.3 Installing Ribbon Cassette (1) Turn off the power before installing ribbon cassette. (2) Turn knob clockwise for 2 to 3 times to tension the ribbon. Turn knob clockwise for 2-3 times
Holder
Knob
(3) Pass ribbon between the ribbon mask and the mechanism head. Then push ribbon cassette down.
(4) Turn knob for 2 to 3 times again to tension the ribbon. Caution: Please use CITIZEN ribbon cassette (model No: NH37701)
-6-
WP-300 One Station Impact Printer 4.4 Installing Paper Roll (1) Turn on the power and open the cover of printer. (2) Tear off the sticker from new paper roll, and set new paper roll to the direction as below picture. (3) Then put the new paper roll on the paper holder.
(4) Pull out the paper to the paper entrance, when the sensor recognizes the paper. It will feed paper automatically.
(5) Push feed button let paper out from the tear bar.
-7-
WP-300 One Station Impact Printer (6) Tear off the last paper. Installing paper roll complete.
(7) Close the cover.
Caution: thickness of paper less than 0.06-0.10 mm. Diameter is not in excess of 80mm.
-8-
WP-300 One Station Impact Printer 5. Control Panel 5.1 Basic Operation
(1)
LF
: Paper feed button
Pressing this button one time feeds one line (1/6 inch). Continually pressing this button feeds paper forward until releasing the button. (2)
BF
: Paper back Button
(3) Pressing this button one time get back one line (1/6 inch). Continually pressing this button keep paper backward until releasing the button. (4) Power : Power Indicator (Green LED) Green light indicates power works properly. (5) Paper : Paper Indicator (Yellow LED) z Continually bright indicates paper near end or paper end. z Continually slow flashing indicates self-testing. (6)
Error : Error Indicator (Red LED) Red Light indicates paper end, paper jam, cutter-lock and printer head lock.
5.2 Status Condition Paper end Black mark error Needle is to hot Cutter lock Head lock Self testing
Beep
Paper LED
3 times Light 3 times Light 3 times 4 times 5 times Flash slowly
-9-
Error LED Light Light Light Light Light -
WP-300 One Station Impact Printer 5.3 Test pattern operating procedure (1) Self-testing LF press
+ Turn on the power (Turn on the power and LF
button simultaneously. It will produce
sound “Beep”).
z
Self-testing will print out content of the version such as configure, font, status and etc as right picture.
z
To end this function needs to turn off the power.
(2) Hexadecimal-testing BF + Turn on the power (Turn on the power and press
BF
button simultaneously. It will produce
sound “Beep”). z The transited data from computer to printer will be printed out as hex as right picture. z This function will help you to check the accuracy of hex-data from computer system to the printer. z To end this function needs to turn off the power.
- 10 -
WP-300 One Station Impact Printer 6. DIP-Switch Setting Please unlock Dip-Switch cover. And find Dip-Switch DIP1 and DIP2 as below picture.
6-1. Select 2-Pass characters print method SW1-2 OFF ON
print method Unidirectional Bidirectional
6-2. Select Handshaking Control SW1-3 OFF ON
Handshaking Control DTR/DSR XON/XOFF
6-3. Select Paper Near End Detect SW1-4 OFF ON
Paper Near End Enable Disable
6-4. Select Setting Mode SW1-5 OFF ON
Setting Mode DIP switch setting Memory switch setting
- 11 -
WP-300 One Station Impact Printer 6-5. Select Paper Type SW1-6 OFF ON
Paper Type Normal Paper Black Mark Paper
6-6. Baud Rate Setting SW1-7 OFF ON OFF ON
SW1-8 OFF OFF ON ON
Baud Rate 9600 bps* 19200 bps 38400 bps 115200 bps
6-7. Select Busy Condition SW2-1 OFF ON
Busy Condition Off line & buffer Full Buffer full, ASB on
6-8. Select Columns/Line SW2-2 76mm OFF 58mm 76mm ON 58mm
Columns/Line 40/33 CPL 31/26 CPL 42/35 CPL 34/28 CPL
6-9. Select Paper Width SW2-3 OFF ON
Paper Width 76mm 58mm
6-10. Select Print Energies SW2-4 OFF ON OFF ON
SW2-5 OFF OFF ON ON
Printing Strength Light Normal Heavy Heaviest
- 12 -
WP-300 One Station Impact Printer 6-11. Select Error Beep Alarm SW2-6 OFF ON
Error Beep Alarm Silence Alarm
6-12. Select Print Dot Alignment SW2-7 OFF ON OFF ON
SW2-8 OFF OFF ON ON
Print Dot Alignment 1 Dot 2 Dots 3 Dots 4 Dots
- 13 -
WP-300 One Station Impact Printer 7. Interface Various interfaces are available for WP-300 such as RS232，Centronic, USB and etc..
7.1 Replace Interface Turn off power before start replacing interface. Unlock screw and take interface out. Then place new interface and lock the screw.
7.2 Serial Interface 7.2.1 Specification (RS-232C) : Asynchronous : DTR/DSR control : 9600，19200，38400，115200 (Refer chapter 6-5) : 8 bit : None
Synchronous Connection Baud Rate Length of Data Parity
7.2.2 Pin Assignment No 2 3 6 20 7
Signal Title TXD RXD DSR DTR GND
I/O In put Out put In put Out put 13
25
Signal Title Transmit data Receive data Data set ready Data terminal ready Signal ground 1
14
- 14 -
WP-300 One Station Impact Printer 7.2.3 Timing Chart Head up or Paper end error RXD DTR Empty RECEIVE BUFFER
Near empty
Near full
256 bytes
Remainder 256 bytes
8K bytes
7.3 Parallel Interface 7.3.1 Specification (Same as Centronics) Data transmission format Synchronizing system Handshaking Signal level
: 8-bit parallel : According to the strobe pulses : According to the BUSY signal : TTL level
7.3.2 Pin Assignment No 1 2-9 10 11 12 13-15 16 17 18
Description STBDATA 1 – DATA 8 ACKBUSY PE NC GND F Ground NC
No
Signal Name
19-30 31 32 33 34-36
Full
TWISTED PAIR GND RESETFAULTGND NC
- 15 -
WP-300 One Station Impact Printer 7.3.3 Time line Buffer near empty release "BUSY" BUSY ACK5 us (Tpy.)
DATA STROBEEmpty RECEIVE BUFFER
0.5 us(Min.) Near empty
Near full
256 bytes
Full
Remainder 256 bytes
8K bytes
- 16 -
WP-300 One Station Impact Printer 8. Cash Drawer Out Put 8.1 Specification (1) Data Transmission System ESC p: Generate cash drawer kick-out pulse ESC u: Transmit cash drawer status (2) Power Characteristic 1. Voltage : DC +24V 2. Current : maximum 0.8A (Less then 510 ms) 3. Switch Signal : Signal level; “L” = 0 to 0.5V “H” = 3 to 5V
8.2 Pin Assignment Number Description 1 2 3 4 5 6
I/O
NC Cash drawer out put 1 Cash drawer on/off signal +24V Cash drawer out put 2 Signal ground 1
Out put In put Out put -
6
8.3 Circuit Diagram
+24V
4 2 Drawer 2
5
Drawer 1
+5V 3 6 Printer Side
User Side
- 17 -
WP-300 One Station Impact Printer 9. Code Table 9.1 Chinese Character 00
10
20
30
40
50
60
70
80
90
A0
B0
C0
D0
E0
F0
NUL
DLE
SP
0
@
P
`
p
Ç
É
á
░
└
╨
α
≣
1
!
1
A
Q
a
q
ü
æ
í
▒
┴
╤
β
+
2
“
2
B
R
b
r
é
Æ
ó
▓
┬
╥
Γ
>
3
#
3
C
S
c
s
â
ô
ú
│
├
╙
π
<
0
4
EOT
$
4
D
T
d
t
ä
ö
ñ
┤
─
╘
Σ
⌠
5
ENQ
%
5
E
U
e
u
à
ò
Ñ
╡
┼
╒
σ
⌡
6
&
6
F
V
f
v
å
û
ª
╢
╞
╓
µ
÷
7
‘
7
G
W
g
w
ç
ù
º
╖
╟
╫
τ
≈
8
(
8
H
X
h
x
ê
ÿ
¿
╕
╚
╪
Φ
˚
9
HT
)
9
I
Y
I
y
ë
Ö
⌐
╣
╔
┘
θ
․
A
LF
*
:
J
Z
j
z
è
Ü
¬
║
╩
┌
Ω
•
+
;
K
[
k
{
ï
¢
½
╗
╦
▉
δ
√
,
<
L
\
l
|
î
£
¼
╝
╠
▄
∞
n
-
=
M
]
m
}
ì
¥
¡
╜
═
Ø
²
.
>
N
^
n
~
Ä
Pt
«
╛
╬
▐
є
■
/
?
O
_
o
SP
Å
ƒ
»
┐
╧
▀
∩
SP
ESC
B C D
CR
GS
E F
US
▌
9.2 International Character ASCII code Country
Hex Dec
23 35
24 36
40 64
5B 91
5C 92
5D 93
5E 94
60 96
7B 123
7C 124
7D 125
7E 126
USA
#
$
@
[
\
]
^
`
{
|
}
~
French
#
$
à
º
ç
§
^
`
é
ù
è
“
Germany
#
$
§
Ä
Ö
Ü
^
`
ä
ö
ü
ß
U.K
£
$
@
[
\
]
^
`
{
|
}
~
Denmark
#
$
@
Æ
∅
Å
^
`
æ
f
å
~
Sweden
#
É
Ä
Ö
Å
Ü
é
ä
ö
å
ü
Italy
#
$
@
º
\
é
^
ù
à
ò
è
ì
Span
Pt
$
@
¡
Ñ
¿
^
`
“
ñ
}
~
Japan
#
$
@
[
¥
]
^
`
{
|
}
~
Norway
#
É
Æ
∅
Å
Ü
é
æ
f
å
ü
Denmark II
#
É
Æ
∅
Å
Ü
é
æ
f
å
ü
$
- 18 -
WP-300 One Station Impact Printer 10. Dimension
- 19 -
