Transcript
Raisecom Technology Co., Ltd.
Datasheet
OPCOM200-FE/GE Media Converter OPCOM200-FE/GE is modular Ethernet to CWDM wavelength converter of Raisecom's CWDM product line to realize the Ethernetsignal-to-CWDM-signal conversion. Industryleading functionalities such as bandwidth control (OPCOM200-FEU only), MDI/MDIX auto sensing, fault pass through and remote management are implemented on OPCOM200-FE/GEU1 converters, enabling a cost-effective and flexible Ethernet transmission over CWDM platform. OPCOM series CWDM products are capable of transporting multiple independent services from 2, 4, to 8 in one single pair of fiberI without interference to each
other. This series products are developed and designed for fully utilizing the existing fiber resources in metropolitan area and carrier's access networks with multiple capabilities of remote management, bandwidth control and auto negotiation. which can be widely used in various networks such as point-to-point, pointto-multi point, chain and ring networks.
Feature
Construction
Installed in 3U16 chassis together with RC series media converters, or in single slot chassis. Must work in pairs. SFP optical module is available. Bandwidth Control Bandwidth Control Function is supported at electrical interface, N*32k (OPCOM200-FEU1) Link faulty detection Support link trouble shooting in electrical link and optical link Auto Negotiation The auto negotiation of electrical port allows OPCOM200-FEU1 to perform automatic configuration to achieve the best possible mode of operation over a link. You also can disable this feature to avoid the mode of operation dropping to the least common denominator when connecting with a nonnegotiating device (i.e. 100Mbps, half-duplex). MDI/MDIX auto Automatically detects and configures the copper port on the converter to sensing the correct MDI or MDIX configuration. This feature eliminates an entire category of troubleshooting Fault-PassSupport Fault-Pass-Through function from electrical port to optical port and Through from optical port to electrical port Loopback Loopback function enables network diagnostics from local or remote site, this provides a flexible method for troubleshooting and is prohibitive to increase truck roll and other maintenance costs. Hot swapped Modular units can be hot swapped in RC002 chassis with high reliability Max Frame size Remote management
1916Bytes frame for OPCOM200-FEU1 No limitation for OPCOM200-GEU1 Configure and monitor the remote end unit through local module, this feature greatly decreases the truck roll and logistic costs. Media converter resetting of local site and customer site is supported through network management platform.
Typical Application
Raisecom Technology Co., Ltd. 620 Haitai Tower 229 Fourth North Loop Middle Road Haidian District, Beijing 100083
Tel: +86 10 8288 3305 Fax: +86 10 8288 3056 Email:
[email protected] http://www.raisecom.com
OPCOM200-FE/GEU1 Media Converter
Specification Port specification (OPCOM200FEU1) Port specification (OPCOM200GEU1) Dimension Power supply
Power consumption Working ambience Storage ambience Safety Compliance
1*10/100M coppor port with RJ-45 connector 1*100M optical port with SFP module 1*1000M coppor port with RJ-45 connector 1*1000M optical port with SFP module 76(W)*170(D)*25(H)mm AC: 90~264V, 47~63Hz DC: 36~75V (Installed in RC002 16-slot chassis) typical value: 4W Temp: 0~45 centigrade RH: 5~90% non-condensing Temp: -40~80 centigrade CE
@2006 Raisecom Technology, Co., Ltd All trademarks are the property of their respective owners. Technical information is subject to change without notice.
Raisecom Technology Co., Ltd.
Raisecom Technology Co., Ltd. 620 Haitai Tower 229 Fourth North Loop Middle Road Haidian District, Beijing 100083
Tel: +86 10 8288 3305 Fax: +86 10 8288 3056 Email:
[email protected] http://www.raisecom.com
@2006 Raisecom Technology, Co., Ltd All trademarks are the property of their respective owners. Technical information is subject to change without notice.
Raisecom Technology Co., Ltd.
Ordering Information
Compliance
Part Number Description OPCOM200-FEU1- 10/100M Ethernet to CWDM wavelength converter with SFP module for CSFP CWDM line site, remotely manageable CSFP-S1/L1/W S1=03, GB, 48 (155M, 1.25GB, 2.5G) L1=S, L (S indicates 40km and L indicates 80km) W indicates CWDM specific wavelength, including 1471nm, 1491nm, 1511nm, 1531nm, 1551nm, 1571nm, 1591nm and 1611nm. CSFP-03/S Rate: 155M, transmission distance: 40km, CWDM SFP optical module CSFP-03/L Rate: 155M, transmission distance: 80km, CWDM SFP optical module OPCOM200-GEU1- 1000M Ethernet to CWDM wavelength converter with SFP module for CSFP CWDM line site, remotely manageable CSFP-S1/L1/W S1=03, GB, 48 (155M, 1.25GB, 2.5G) L1=S, L (S indicates 40km and L indicates 80km) W indicates CWDM specific wavelength, including 1471nm, 1491nm, 1511nm, 1531nm, 1551nm, 1571nm, 1591nm and 1611nm. CSFP-GB/S Rate: 1.25G, transmission distance: 40km, CWDM SFP optical module CSFP-GB/L Rate: 1.25G, transmission distance: 80km, CWDM SFP optical module *OPCOM200-FEU1 and OPCOM200-GEU1 consist of two parts: optical wavelength converting card, CWDM SFP optical module (CSFP)
Standards & protocols
Raisecom Technology Co., Ltd. 620 Haitai Tower 229 Fourth North Loop Middle Road Haidian District, Beijing 100083
Tel: +86 10 8288 3305 Fax: +86 10 8288 3056 Email:
[email protected] http://www.raisecom.com
IEEE802.3x on full duplex on IEEE802.3 10BaseT IEEE802.3u 100BaseTX IEEE802.3ab 1000BaseT IEEE802.3z 1000BaseX
@2006 Raisecom Technology, Co., Ltd All trademarks are the property of their respective owners. Technical information is subject to change without notice.
