Preview only show first 10 pages with watermark. For full document please download

Operační Manuál

Rating
Date

August 2018
Size

3.9MB
Views

6,382
Categories

computers & electronics Print & Scan POS/mobile printers

Transcript

ＱＰ－０５１－Ｄ１ PMU2300ⅢSeries Product Specification Model name ：PMU2300ⅢSeries Destination ：CSJ, CSA, CSE, CSHK Revision ：1.00 Revision Date ：Jul 26th 2010 Assurance Quality ： Sales Support ： Engineering ： ZF74904-00F 0413_30468_3_E_G Revision List Revised First Draft Issue date Details chapter Approval Confirmation (page) 1.00 2010.07.26 Newly created Kohyama Revised by Inoue PMU2300ⅢSeries Product Specification Contents 1 PRODUCT OUTLINE .........................................................................................................................................1 1.1 Features ......................................................................................................................................................................................1 1.2 Accessories .................................................................................................................................................................................1 1.3 Product Classification..............................................................................................................................................................2 1.4 Product structure（Block Diagram）.................................................................................................................................3 2 GENERAL SPECIFICATION ...........................................................................................................................4 2.1 Printing Specification ..............................................................................................................................................................4 2.2 Basic model name.....................................................................................................................................................................5 2.3 Printing Paper...........................................................................................................................................................................7 2.4 Black Mark Specification (M type) (Optional) ..................................................................................................................9 2.5 Auto Cutter Specification......................................................................................................................................................11 2.6 Power Supply ..........................................................................................................................................................................13 2.7 Machine Reliability................................................................................................................................................................15 2.8 Safety (Applicable Standards) .............................................................................................................................................15 2.9 Environmental Conditions ...................................................................................................................................................16 3 OPERATION PANEL ........................................................................................................................................18 3.1 LED Panel................................................................................................................................................................................18 3.2 Details on Error and LED Indication ................................................................................................................................19 3.3 FEED SW ................................................................................................................................................................................22 3.4 External Output of Switch Operation................................................................................................................................26 4 INTERFACE.........................................................................................................................................................28 4.1 RS-232C Serial Interface......................................................................................................................................................28 4.2 Bidirectional Parallel Interface (IEEE1284).....................................................................................................................31 4.3 USB INTERFACE.................................................................................................................................................................38 5 PLACE OF DESTINATION.............................................................................................................................39 5.1 Memory switch .......................................................................................................................................................................39 5.2 Serial connector screw...........................................................................................................................................................39 5.3 ROM version...........................................................................................................................................................................39 6 PAPER HOLDER UNIT / KIT: OPTION......................................................................................................40 6.1 Paper Insertion Direction .....................................................................................................................................................41 6.2 Paper holder attachment position.......................................................................................................................................42 6.3 PNE (Paper near end ) Sensor.............................................................................................................................................43 7 FUNCTION SELECTION ................................................................................................................................46 7.1 Dip switch (serial interface)..................................................................................................................................................46 7.2 Memory Switches...................................................................................................................................................................47 8 SET UP ...................................................................................................................................................................51 8.1 Component Names.................................................................................................................................................................51 -i- PMU2300ⅢSeries Product Specification 8.2 Precautions...............................................................................................................................................................................54 8.3 How to Set Paper (Replacement)........................................................................................................................................56 8.4 How to Release Cutter Lock (Cutte Error).......................................................................................................................58 8.5 How to Remove Paper Jam..................................................................................................................................................59 8.6 Function of Presenter ............................................................................................................................................................62 8.7 Bezel function..........................................................................................................................................................................64 8.8 Maintenance............................................................................................................................................................................65 9 DIMENSIONAL DRAWINGS .........................................................................................................................66 9.1 PMU2300ⅢSN Outline Drawings......................................................................................................................................66 9.2 PMU2300ⅢSB Outline Drawings (Bezel equipped model)..........................................................................................67 9.4 PMU2300ⅢPB Outline Drawings (Bezel/Presenter equipped model).......................................................................69 9.5 PMU2300ⅢSB Outline Drawings (Bezel equipped) Holder PHU-102S attached...................................................70 9.6 PMU2300ⅢPB Outline Drawings (Bezel/Presenter equipped)Holder PHU-203 attached ...................................71 9.7 Installation ...............................................................................................................................................................................72 10 PRINT CONTROL COMMANDS................................................................................................................74 11 CHARACTER CODE ......................................................................................................................................78 11.1 Codepage................................................................................................................................................................................78 11.2 International Characters Code..........................................................................................................................................90 11.3 Kanji Code Chart.................................................................................................................................................................91 - ii - PMU2300ⅢSeries Product Specification 1 Product Outline - The contents of the specification applies exclusively to KIOSK Printer PMU2300ⅢSeries - The contents of this specification may be changed without warning. - The reprint, copy, duplicating and alteration of this specification without acceptance of our company are prohibited. 1.1 Features 1) The down-sizing is realized. 2) High-speed 150mm/s printing 3) High resolution printing with 8 dots/mm 4) Supports paper width of 80mm 5) Supports long life printer head, highly-reliable simple mechanism 6) Operating temperature range -10°C to +60°C. 7) Simple head / paper maintenance by adopting the new head open mechanism. 8) Interface serial, parallel, USB (printer class, virtual COM). 9) OEM available 10) Black mark (factory option) 11) Equipped with presenter function that enables the discharge / recovery of printed or cut paper. 12) Lights up printing paper discharge port by bezel LED display. 13) Supports paper holder with a large diameter (φ203mm) 1.2 Unpacking There are the following items. 1) User ‘s Setup manual ……………………………………………………… 1 2) Printer ……………………………………………………… 1 3) Cable for wiring power supply ……………………………………………………… 1 4) Cable for Parallel I/F (for Parallel I/F model only) ………………………………………… 1 -1- PMU2300ⅢSeries Product Specification 1.3 Product Classification 1.3.1 Model Name ＰＭＵ２３００ⅢＰＢ ‐ ＲＳＪＭ１ ① ② ③ ④ ⑤ ① Specification of mechanism S: Standard ● P: Standard＋presenter ② Bezel ● N: Not equipped with Bezel B: Equipped with Bezel ③ Interface (Serial P30, Parallel P33, USB P40;） RS: Serial UB: USB ④ Destination (See P41) J: Japan PA: Parallel U: North America/Europe ⑤ Sensor（Black Mark）(For Black Mark Specification, see P10） ● No mark: No sensor M1: Black Mark（left） M2: Black Mark（right） 1.3.2 Optional（Paper holder）ＰＨＵ - １０２Ｓ ① ② ① Maximum paper diameter 102: φ102mm 203: φ203mm ② Paper insertion direction S: Side insertion T: Top insertion 1.3.3 Precautions 1) Registration in the printer main unit Following items has been registered in the printer main unit as a factory option depending on the model and they cannot be changed by a user. - Model name of self printing (See P25) - ROM version of self printing (See P25) - Initial value when it is shipped from factory (initial value of command "reset all contents set by GS ( E function: 255 printer function setting mode) to the factory-setting status", varies depending on the model) * It is possible to change the setting to the same setting as that of other model by memory switch setting. -2- PMU2300ⅢSeries Product Specification 1.4 Product structure（Block Diagram） PMU2300Ⅲ SERIES BLOCK DIAGRAM Presenter MECHANISM CUTTER CUTTER MOTOR RETRACTION SENSOR HEAD Thermistor PE SENSOR PRESENTER SENSOR CUTTER SW Presenter MOTOR HEAD UP SENSOR PRINTER HEAD FEED MOTOR BEZEL BEZEL SENSOR BEZEL LED DRIVER DRIVER DRIVER FLASH MEMORY POWER LED SDRAM 16Mbit CPU ERROR LED POWER LED DC3.3V FEED SW DC24.0V OSC 4MHz ERROR LED RESET DIP SW FEED SW DC5.0V VOLT SENSOR POWER SUPPLY INTERFACE PNE SENSOR BM SENSOR Serial Interface RS-232C Parallel Interface USB Interface IEEE1284 Centronics Fig. 1-1 Block Diagram -3- DC24.0V PMU2300ⅢSeries Product Specification 2 General Specification 2.1 Printing Specification Table 2-1 Specification List Items PMU2300ⅢSeries PMU2300ⅢSN PMU2300ⅢSB Printing Method Dot configuration (Max.) Dot density Line thermal (thermal printing method) Printing speed ※1 MAX 150mm/sec. (1200 dot line / sec.) Paper feed 0.125mm Printing line columns (Max.) Font A : 48 digits Printing size Character type PMU2300ⅢPN PMU2300ⅢPB 72mm/576 dots 8 dots / mm Font B : 64 digits Kanji FontA : 24 digits Font C : 72 digits Kanji Font : 36 digits FontA：12×24 dots 1.50×3.00mm FontB：9×24 dots 1.13×3.00mm Font：8×16 dots 1.00×2.00mm Kanji Font A：24×24 dots 3.00×3.00mm Kanji Font C : 16×16 dots 2.00×2.00mm As the space in the character font is included, the actual character is smaller than the size shown above. Alphanumeric, International Characters (12 characters×16 countries), Code 437、850（858）、852、857、858、860、863、864、865、866 WPC1252, Katakana, Thai code18 Kanji (JIS Category 1, 2)､kana､JIS C 6226-1983 User memory 256KB(User generated character, created logo can be registered) Bar codes UPC-A/E, JAN(EAN)13digits/8digits, ITF, CODE39, CODE128, CODABAR, CODE93 PDF417, QR code Line feed rate 4.25mm (approx.1/6 inch) can be set with command Printing paper Interface Paper width: 80mm Paper thickness PMU2300Ⅲ：60～87μm Serial (RS-232C C compliant) Parallel（IEEE 1284 compliant)） USB (Printer class, Virtual COM) Presenter Minimum length of ticket :75mm ― ― (Valid at setting MSW11-6) Number of paper discharge:1 million times (65μm) Input buffer 4K/45 byte(only 4K for parallel) Power source Input voltage DC24V±10% power consumption 1.9A (9A at peak)*Optional AC Adapter 36AD1 compliant Weight 0.9kg 1.0kg 1.2kg 1.2kg Operating temperature －10～60°C (※36AD1 0～45°C when in operation) 10～80% (no condensation) Storage temperature －25～65°C 10～90% (no condensation) Machine reliability Printer head life: 100km, 100 million pulse (normal temperature, normal humidity, recommended paper) Auto cutter life:1 million cut (normal temperature, normal humidity, thickness 65μm when full cut) Applicable Standards *2 VCCI Class A UL､C-UL､FCC Class A TUV､GS､CE Marking *1 - The printing speed above should be under the conditions of voltage at 24.0V, 25°C, printing Duty12.5% - The printing speed may be slow depending on the setting of printing condition or combination of commands. *2 - The above specification applies exclusively when using dedicated AC adapter (36AD1) -4- PMU2300ⅢSeries Product Specification 2.2 Basic model name - The basic model is determined by the association of mechanism specification and bezel. - The basic model is a factory option and cannot be rearranged or changed by a user. ● Standard model PMU2300ⅢSN-□□□ Fig. 2-1-1 Standard model ● Bezel equipped model PMU2300ⅢSB-□□□ Fig. 2-1-2 Bezel equipped model -5- PMU2300ⅢSeries Product Specification ● Presenter equipped model PMU2300ⅢPN-□□□ Fig. 2-1-3 Presenter equipped model ● Bezel + Presenter equipped model PMU2300ⅢPB-□□□ Fig. 2-1-4 Bezel + Presenter equipped model - 6 - PMU2300ⅢSeries Product Specification 2.3 Printing Paper 2.3.1 Paper width and valid printing width (printing area) 1) Paper width All settings for paper width are factory options, and they cannot be changed by a user. Valid printing width Left margin 4±2 mm Printing paper feed direction HHHHHHHH･･･････HHH Valid printing width 63mm (MSW3-5：ON) HHHHHHHH･･･････HHHHHHH Valid printing width 72mm (MSW3-5：OFF) Paper width 80+0,-1 mm Figure 2-2 Paper width and effective printing width (printing area) 2) Valid printing width (Printing area） With MSW3-5 “Printing line column” setting, valid printing width (printing area) can be changed. Table 2-2 MSW3-5 Printing line column 42 ON column OFF 48 column Valid printing width (printing area) Font A Font B Font C Kanji FontA Kanji Font C 42 56 64 21 31 column column column column column 48 64 72 24 36 column column column column column Valid printing width 63mm 504 dots 72mm 576 dots * Effective printing width is based on left side 2.3.2 Printing size Table 2-3 Printing size FontA FontB Font C Kanji FontA Kanji Font C 12×24 dots 9×24 dots 8×16 dots 24×24 dots 16×16 dots 1.50×3.00mm 1.13×3.00mm 1.00×2.00mm 3.00×3.00mm 2.00×2.00mm *As the space in the character font is included, the actual character is smaller than the size shown in the table above. -7- PMU2300ⅢSeries Product Specification 2.3.3 Paper Diameter Paper width Paper diameter Core diameter Fig. 2-3 Paper size Table 2-4 Paper diameter Item Description Max. paper diameter Paper width Core diameter Φ203mm：diameter, Holder PHU-203T Φ102mm：diameter, Holder PHU-102S (also applicable for Holder 203T） 80 +0/-1 mm Inner Φ25.4±1 mm Exterior Φ31.4±1 mm Precautions *Use paper material for the core. Do not use any plastic materials. 2.3.4 Recommended thermal paper, Setting print density Print density setting should be changed according to the type and thickness of paper. It is recommended that print density be changed through GS switch and customized value （P47「See 7.2 」） Manufacturer Table 2-5 Recommended Thermal Paper Paper thickness Product name Features (μm) Nippon Paper TF50-KS-E2D normal type 67 Mitsubishi Paper HP220AB-1 high quality preservation type 75 Nippon Paper TF62KS-E normal type 87 Remarks Precautions * Use the specified thermal paper as the printing result is affected by the condition of used thermal paper (storage environment, aged deterioration).- If you use the paper other than the specified paper, the printing density may become low and the paper feed accuracy may degrade, so it is necessary to make an adjustment by raising the printing density or reducing the printing speed etc. * Be careful of storage temperature environment. The printing result may fade. 2.3.5 Others - Coloration: external side of roll paper. - End processing: Do not fix the paper and the shaft core. - Do not fold the paper end. - 8 - PMU2300ⅢSeries Product Specification 2.4 Black Mark Specification (M type) (Optional) The black mark sensor and the black mark sensor position (M1, M2) are factory option; they cannot be changed by a user. 2.4.1 Black mark position Black mark (printed on the rear face of printing paper) Paper feed direction Cut position 15mm Surface of printing 5mm 2.5mm 11mm or more A=42 Printing range ～300mm 5+0.03×Amm M2specification M1specification Fig.2-4 Black mark 2.4.2 Precautions - The printing range when the black mark is used should be within the use range shown in the figure above. - For the setting value of printing range in the paper feed direction, be sure to ensure the margin shown in the figure above not to exceed the pitch of the black mark. Take note that the defect of skipping page may be generated if the margin is not ensured. - The values are design center values and the printing area, right and left margins may be misaligned by up to 2mm depending on the paper position and the variation of parts. For the printing head alignment accuracy by black mark detection, consider the error of ±2mm for the standard printing position, and for the printing length, consider the error of ±5% for the setting value because there is variations of environmental temperature and platen diameter processing accuracy and if you use the printed paper, pay attention to the printing layout sufficiently. The pre-printing on the rear face of the paper is prohibited. - The PCS value of the black mark should be 0.90 or more. -9- PMU2300ⅢSeries Product Specification 2.4.3 Memory Switch Setting The memory switch setting related to the black mark is shown below. Table 2-6 Memory switch setting No. Function OFF ON MSW3-4 Paper Select Thermal Black MK MSW4-1 Auto Length Invalid Valid ■･･･Default (factory-setting) ● MSW3-4 Paper Select When "Thermal" is selected, the operation is based on the setting of the thermal paper as paper to be used and when "Black MK" is selected, the operation is based on the setting of the black mark paper as paper to be used. * If "black mark paper" is selected when the model does not support black mark sensor If MSW3-4 "Paper Select" is set to ON " Black MK " by mistake for the memory switch setting operation for the model on which the black mark sensor is not mounted, the setting cannot be changed by communication. In this case, set MSW3-4 " Paper Select " to OFF " Thermal " again by the manual operation in the memory switch setting mode (refer to P27 "3.3.3 ") and recover the system. In the memory switch setting mode, the black mark paper setting is released, so it is possible to change the setting using the thermal paper. ● MSW4-1 Auto Length If it ibis set to valid, the length measurement operation is automatically carried out when the power supply is turned ON. - 10 - PMU2300ⅢSeries Product Specification 2.5 Auto Cutter Specification 2.5.1 Specification Paper feed direction Auto cutter position 11mm Printing start position Fig. 2-5 Auto cuter cutting position Table 2-7 Auto cuter specification Item Cutting method Cutting mode Cutting duty Thickness of paper Minimum cutting length Description Slide cutter (V-shape movable blade) Full cut (Cut off ） Partial cut (substantially central position) supported 20 cut/minute 65μm to 150μm 30mm Error detection Home position is detected by mechanical sensor Cutting position Distance from printing position to cutting position is approx. 11mm Paper Paper Cutting line Cutting line Paper Paper Fig. 2-6-1 Full cut Fig. 2-6-2 Partial cut 2.5.2 Precautions - Usage duration depends upon print setting (density) or printing paper. Be sure to have enough space for cutting position - It is recommended to ensure 5mm or more of page margin from printing end to the cut position. - When presenter is set at valid, allow a space of 5mm or more between the printing edge and cut position specifically for full cut operation - 11 - PMU2300ⅢSeries Product Specification 2.5.3 Memory Switch Setting Memory switch setting for auto cutter is as follows Table 2-8 Memory switch setting for Auto cutter No. Function OFF ON MSW2-2 Auto Cutter Invalid Valid MSW3-1 Resume Cttr Err Valid Invalid MSW4-3 Feed&Cut at TOF Invalid Valid MSW4-8 Partial Only Invalid Valid ■…Default (Factory setting) ●MSW2-2 Auto Cutter When setting is valid, cutter operation will be executed. When the presenter is set to valid, the cutter operation is carried out regardless of the setting of MSW2-2. ●MSW3-1 Resume Cttr Err When it is set to valid, the system recovers from an error by pressing FEED switch when the cutter lock error is generated. However, the system may not recover from the error even if FEED switch is pressed depending on the status of the cutter lock. In that case, release the cutter lock error referencing P60 “8.4 How to Release Cutter Lock (Cutte Error)” ●MSW4-3 Feed&Cut at TOF When setting is valid, following operation will be executed MSW3-4 OFF：Selecting ”Thermal” - After auto loading, full cut operation - After opening-closing platen, full cut operation - When performing paper feed for 25mm or more with FEED SW, full cut operation MSW3-4 ON ：Selecting ”Black MK” - After auto measuring, full cut operation - After opening-closing platen, full cut operation - After setting at cue position with FEED SW, full cut operation MSW11-1ON: select "presenter valid" - After the full cut operation above, the paper is discharged. ●MSW4-8 Partial Only When setting is valid, all cut operation will be forced partial cut and full cut will not be performed. When the presenter is set to valid, all cut operations are set to full cut regardless of the setting of MSW4-8 and the partial cut operation is not carried out. - 12 - PMU2300ⅢSeries Product Specification 2.6 Power Supply 2.6.1 Power connector Pin configuration (CN101) Connectors available： B4PS-VH (JST(JST Mfg. Co., Ltd.)）or equivalent Table 2-9 Connector Pin Configuration (CN101) Connector lock section 1 2 3 Pin No. Signal name 1 +24V 2 GND 3 GND 4 GND 4 Main board Fig. 2-7 CN101Power connector 2.6.2 Specification - Operation voltage: DC24V±10% - Consumption current Table 2-10 Consumption current Paper width 80 mm (576 dots) Item Average voltage (24.0V, 25°C, Printing Duty12.5%) PMU2300ⅢSN PMU2300ⅢPB Approx.1.5A Approx.2.5A Peak voltage (at full dot printing) Approx. 9.0A At standby Approx. 90mA * The above specification applies exclusively when using separately sold AC adapter (36AD1) Input voltage AC100/120/230V±10% However, operating temperature will be 0°C to 45°C. 2.6.3 Included cable for the wiring of power supply Table 2-11 Cable specification Item Description Housing VHR-4N（JST(JST Mfg. Co., Ltd.)）or equivalent Terminal SVH-21T-P1.1 JST (JST Mfg. Co., Ltd) Cable AWG18(UL1007) or equivalent Cable length 300mm (cut off at the point) - 13 - PMU2300ⅢSeries Product Specification 2.6.4 Precautions 1) Before connecting or disconnecting the connector, be sure to turn OFF the power supply. 2) Be sure to use the input voltage within the specification range. 3) Be sure to use the product by connecting Vp and GND completely. 4) For the power supply, use the power supply from which the peak current can be obtained. 5) The excessive pulling of power supply cable will cause the operation failure due to voltage drop etc., so pay attention to the wire pulling length and the wire rod diameter. 6) If you use the power supply other than that is within specification, it may negatively affect the printing operation etc. 7) If you use the power supply from which the peak current cannot be obtained, the printing quality loss or the low-voltage error may be generated depending on the content of printing. 8) For precautionary measure, power supply should be enabled to be turned OFF easily. 9) Use the power supply with overvoltage protection, over current protection, and various protection circuits. 10) Pay attention to improper wiring and misuse. Improper use may damage the printer and affect the human body and other peripheral equipment etc. 11) The power supply voltage range is 24V±10%, however, the print density changes depending on the voltage. In that case, make an adjustment with MSW10-1 "Print Density". No. MSW10-1 Table 2-12 Customized value Function Setting Print Density 70% 75% 80% 85% 90% 95% 100% 105% 110% 115% 120% 125% 130% 135% 140% ■･･･Default (factory preset) - 14 - PMU2300ⅢSeries Product Specification 2.7 Machine Reliability 2.7.1 Life Duration - Machine usage duration : 23 million lines - Thermal Head : 100 million pulses, 100 km (An average of the head resistance fluctuation keeps under ±15%) - Auto Cutter : 1 million cut (65μm, at Full cut) - Average Printing Rate : 12.5% - Recommended thickness of thermal paper : 65μm - Number of paper discharge : 1 million times 2.7.2 MCBF - MCBF：2.3 million lines The definition of MCBF should be integrated mean time between failure which includes chance failure and wear-out failure until the lifetime of machine, 23,000,000 lines. - Precautions The lifetime of machine is adamantly 23,000,000 lines, and MCBF does not show the usable lifetime. 2.7.3 Precautions Machine reliability specification above shows the value when the recommended thermal paper is used and the print density is set to 100%. Reliability cannot be assured for paper other than the recommended thermal paper. 2.8 Safety (Applicable Standards) 2.8.1 Safety Standard UL C-UL TUV PSE Law 2.8.2 EMI Standard - FCC - VCCI - EN55022 Main unit UL60950-1:2003 1st CSA22.2 NO.60950-1-03 1st EN60950-1/A11:2004 ― ClassA ClassA ClassA 2.8.3 CE Marking - EMC Directive、Low Voltage Directive - 15 - PMU2300ⅢSeries Product Specification 2.9 Environmental Conditions 2.9.1 Temperature, Humidity 1) During operation - Temperature - Humidity : －10°C to 60°C : 10％RH to 80％RH (no condensation) 100 ） Relative humidity (%RH) 40℃ 80％ 80 60 Operating Temperature range 40 20 60℃ 10％ 0 －20 0 20 40 60 Environment temperature (°C) 2) Not in operation (excluding rolled paper) - Temperature : －25°C to 65°C - Humidity : 10％RH to 90％RH (no condensation) * In this regard, the combination of 40°C and 90% RH (Non Condensing) shall be the worst value for high temperature, high humid restoring. - 16 - PMU2300ⅢSeries Product Specification 2.9.2 Vibration, Falling, Impact 1) Vibration test (when packed) Direction of vibration Vibration frequency Sweeping time Acceleration of vibration Applied time Wrapping Status XYZ Sine wave 10Hz to 55Hz Target sweeping 10 minutes (go and back) 2G (fixed) 1 hour (total 3 hours) Smallest There were no problems found in the appearance and the function after the vibration test. 2) Drop and impact test (when packed) Height of dropping 60cm Direction of Dropping 1 Corner 3 Sides 6 Surfaces Frequency of Dropping Once each (total 10 times) Packing Status Smallest There were no problems found in the appearance and the function after dropping 3) Impact test (when not packed) Height of dropping 5 cm Direction of Dropping 4 Sides Only one side was supported. Frequency of Dropping 5 times each (total 20 times) There were no problems found in the appearance and the function in operation after dropping during non-operation. 2.9.3 Noise Measurement Standard: Noise should be 65 dB or less. Note: The above noise value is by the print pattern for our evaluation. The noise value may change with the paper used, printing duty, and setting (print speed, print density). - 17 - PMU2300ⅢSeries Product Specification 3 Operation Panel Various operations and status can be checked on the operation panel on the right side of the printer. FEED Switch ERROR LED POWER LED Fig. 3-1 Operation panel 3.1 LED Panel 1）POWER LED (Green) ON : Power is supplied. Blinking : Memory check error. Hexadecimal dump mode, Memory switch setting mode, Self printing OFF : Power is not supplied. 2）ERROR LED（Red） ON : Memory check error, Platen open, Paper-end, Paper near end Blinking : Various kinds of error, Macro execution wait OFF : Normal operation - 18 - PMU2300ⅢSeries Product Specification 3.2 Details on Error and LED Indication Table 3-1 Error and LED Indication POWER LED (Green) Description 1) Error to recover automatically ① Head overheat error ② Platen open error (MSW3-8 OFF: Recover automatically) 2) Restorable error ① Platen open error (MSW3-8 ON: At the setting of recoverable feature) 3) Error impossible to restore 4 ) Other conditions 5) Black mark specification ERROR LED (Red) ON ON ON ② Cutter lock error ON ➂ Presenter error ON ① Memory check error ON ② Low voltage error ON ➂ High voltage error ON ① Paper near- end ON ON ② Paper-end ON ON ➂ Platen open ON ON ④ Waiting for a macro execution ON ① Black mark paper detection error ON 1) Error to recover automatically ① Head overheat error - Description : When the head temperature exceeds the specified range (higher than 75ºC), the head temperature sensor is activated to stop printing while blinking ERROR LED to protect the print head from overheating. Automatically returns when the temperature drops (lower than 70ºC). - POWER LED : ON - ERROR LED : Blinking (ON time is long) - Recovery condition : Automatically returns when the temperature drops ② Platen open error (MSW3-8 OFF: when the automatic recovery is set) - Description of error : If the platen is opened during the printing (the platen open lever is pushed up and the platen holding unit is opened) - POWER LED : Lighting - ERROR LED : Blinking with long lighting - Recovery condition : Close the platen (Close the platen holding unit and keep the platen open lever pushing up). - 19 - PMU2300ⅢSeries Product Specification 2) Restorable error ① Platen open error (When MSW3-8 is set to ON.) - Description : ERROR LED flashes when the printer cover is opened during paper feeding or printing.(lifting the platen open lever, platen hold unit is open) - POWER LED : ON - ERROR LED : Blinking (ON time is long) - Recovery condition : The errors should be resolved by commands. ② Cutter lock error - Description - POWER LED : Cutter cannot work. Abnormality occurred. : ON - ERROR LED : Two quick blinking and then one slow blinking - Recovery condition : Remove the trouble and press the FEED SW to restore or send DLE ENQ 1 or 2 commands to restore. See Command reference for details ➂ Presenter error - Description - POWER LED - ERROR LED - Recovery condition : Cannot discharge the paper or cannot collect the paper : ON : Two quick blinking and then two slow blinking : Open the platen or cover unit to remove the trouble. Set the cover unit. Then close the platen. 3) Error impossible to restore ①Memory check error - Description of error : When CPU carries out the self diagnosis of circuit and detects a defect in the external RAM memory - POWER LED : Short blinking - ERROR LED : Lighting - Recovery condition : The recovery is impossible. However, if you turn OFF the power supply and eliminate the cause of defect by replacing the external RAM etc., the system recovers. ②Low voltage error - Description : The voltage supplied to the printer is too low. The printer should be turned off immediately. - POWER LED : ON - ERROR LED : Three quick blinking, and then one slow blinking. (Repeated) - Recovery condition : The printer cannot be restored. However, if setting the VP DC24V±10% after turning OFF, it will be restored ③High voltage error - Description : The voltage supplied to the printer is too high. The printer should be turned off immediately - POWER LED : ON - ERROR LED : Four quick blinking, and then one slow blinking. (Repeated) - Recovery condition : The printer cannot be restored. However, if setting the VP DC24V±10% after turning OFF, it will be restored - 20 - PMU2300ⅢSeries Product Specification 4) Other conditions ①Paper near- end - Description : When the radius of the paper roll gets smaller (approx.ţ24 toţ30), the sensor detects that there is little paper left by lighting the POWER and PAPER LED. (MSW2-8 OFF：PNE valid setting) - POWER LED : ON - ERROR LED : ON - Recovery condition : Set another roll paper ②Paper-end - Description : When the roll paper runs out, the paper-end sensor in the paper pathway near the printing head detects the end of roll paper, and the POWER, ERROR, and PAPER LED light up to stop the printing operation. - POWER LED : ON - ERROR LED : ON - Recovery condition : Set another roll paper ③Platen open - Description : When the platen cover is opened during standby, ERROR LED light up to stop the printing operation. - POWER LED : ON - ERROR LED : ON - Recovery condition : Close the platen. ④Waiting for a macro execution - Description : The printer is waiting for a macro execution by ESC/POS‟s commands. - POWER LED : ON - ERROR LED : Blinking slowly (Repeated) - Recovery condition : Push the FEED SW. 5) Items related to black mark (option) specification ① Black mark detection error (automatic recovery error) - Description or error : If the black mark cannot be detected or the used paper is without the range of specification, the printer enters BUSY status. - POWER LED : Lighting - ERROR LED : After two times of long blinking, short blinking is repeated three times. - Recovery condition : Set the paper within the specification. * If the black mark paper is set for the memory switch setting operation by mistake for the model on which the black mark sensor is not supported, reset it to the thermal paper setting in the memory switch setting mode (refer to P9 "2.4 Black Mark Specification (M type) (Optional)"). - 21 - PMU2300ⅢSeries Product Specification 3.3 FEED SW 1) Paper feed function When pressed once, the printer feeds one line depending on the amount of line feed set by ESC 2 and ESC 3. However, the printer does not feed in the following cases. Table 3-2 No. 1 2 3 4 5 Condition when paper feed is not possible Condition When the FEED SW is disabled by ESC c 5. When paper-end sensor detected the end of roll paper,. When the platen cover is opened. When error occurs. When waiting for macro (execution of macro by FEED SW), it is executed by pressing FEED SW. 2) Cutter lock error release (MSW3-1 OFF:FEED switch is set to valid） While during cutter lock error, after eliminating the cause of error, press the FEED switch and the error will be released 3) Paper feed cut (MSW4-3 ON: when paper head alignment cut is set to valid) If the paper is fed by 25mm or more by pressing FEED switch, the cutting is carried out. MSW3-4 ON: When "black mark paper" is selected, the full cut operation is carried out after the head alignment by pressing FEED switch. MSW11-1 ON: When "presenter function valid" is selected, the paper is discharged after the paper feed of the minimum issue length or more and the full cut operation by pressing FEED switch. - 22 - PMU2300ⅢSeries Product Specification 3.3.1 Self Printing Mode 1) Function Function to enable the printer setting status to be verified by printing. 2) Starting the Self printing When the power is turned on with the FEED SW pressed and hold the print ready state, printer status is printed on the roll paper. The content of printing is shown as below. 1. Name of the printer ：PMU2300ⅢPB–RSUM1 (See P2) 2. ROM version ：DC21-XXXX(See P2） 3. BOOT version ：XXX.XX 4. FONT version ：XXX.XX 5. I/F Setup 6. Buffer size 7. Dip switch (Serial interface only) 8. Contents of the memory switch 9. Font A(20H～FFH) 10.Font B(20H～FFH) 11 Font C(20H～FFH) 12. Kanji Font A 192 characters (Only Kanji specifications:MSW9-3) 13. Kanji Font C 192 characters (Only Kanji specifications: MSW9-3） 3) Completing the Self printing. When the printing of certain printing pattern is terminated, the printer is reset and initialized. * If the self printing is carried out when the black mark paper is specified, the printing is carried out without executing the control related to the black mark, so the printing following the format of (2.4 Black mark specification) is not carried out. However, when the self printing is executed by the test printing command, the printing is carried out by executing the control related to the black mark. - 23 - PMU2300ⅢSeries Product Specification 3.3.2 Hexadecimal Dump Mode Printing 1) Function This is the function to print the data sent from host machine with hexadecimal number and its corresponding characters 2) Starting hexadecimal dump - Set the printing paper. While platen cover is open. - Turn the power supply to ON by holding down the FEED switch when the paper is set. Close the platen cover. - "HEX Dump printing mode" is printed on the roll paper, and the following data received is printed with hexadecimal number and its corresponding characters. Example) When hexadecimal dump printing is executed at Kanji valid setting (MSW9-3 Kanji: Valid ) ＨＥＸダンプ印字モード 1B 40 31 32 33 34 35 36 .@123456 37 38 39 30 0A 7890. Completed Example) When hexadecimal dump printing is executed at Kanji invalid setting (MSW9-3 Kanji: invalid ) HEX DUMP PRINT MODE 1B 40 31 32 33 34 35 36 .@123456 37 38 39 30 0A 7890. Completed - While executing hexadecimal dump, the command other than the real time command does not function. - When the printing data is less than one line, the line is printed by generating offline 3) Closing the hexadecimal dump - Push down FEED switch three times continually. - Turn off the printer or reset by I/F signal. - Receive rest command from I/F. - 24 - PMU2300ⅢSeries Product Specification 3.3.3 Memory Switch Setting Mode 1) Available setting for Memory switch MSW1、MSW2、MSW3、MSW4、MSW5、MSW7、MSW9、MSW10、MSW11、MSW12 2) Entering the memory switch setting mode With paper set and printer cover open, turn the printer power on while pressing and holding the FEED switch. Press the FEED switch twice, and close the printer cover, the mode is started. After the setting mode is started, the guidance of setting content and operation method is printed. 3) Selecting memory switch By pressing the FEED switch short (less than 0.5 second), the memory switches to be set shift in the following order. Moreover, by detecting the paper by applying the paper to the recovery sensor and pressing the FEED switch short in a same way, the memory switches to be set shift in the reverse order of order shown below. At that time, the status of the selected memory switch is printed. However, when (11) is selected, the confirmation of flash memory writing is printed. (1)MSW1 → (2)MSW2 → (3)MSW3 → (4)MSW4 → (5)MSW5 → (6)MSW7 → (7)MSW9 → (8)MSW10 → (9)MSW11 → (10)MSW12 → (11)Write / setting initialized Caution - While selecting 1. To 10, select the memory switch to be set and press FEED switch long (more than 2seconds). (step 4 below) entering memory switch) - While selecting 11, press FEED switch long (more than 2seconds), all of the setting of memory switch will be written in flash memory and reset. (step 5 below) exiting the memory switch setting mode) - While selecting 11, press FEED switch long (more than 2seconds), memory switch setting will be returned to the factory set values, and rest. (step 5 below) exiting the memory switch setting mode) 4) Memory switch setting ① The status of setting item that is currently set is printed. ② By pressing the FEED switch short (less than 0.5 second), the content of currently selected setting item is changed. At that time, if the status of the selected item is the currently set content, ERROR LED lights up. ③ By pressing the FEED switch long (2 seconds or more), the setting of current setting item is terminated and the setting shifts to the next setting item, and then the setting of the next setting item is started. ④ By opening the platen, the setting related to the currently selected memory switch is terminated. Then, the status of the memory switch after the change is printed by closing the platen and the operation shifts to "3) Memory switch selection". 5) Exiting the memory switch setting mode Setting will be saved, returns to initial state and exits the memory switch setting mode to return to the normal standby state. - 25 - PMU2300ⅢSeries Product Specification 3.4 External Output of Switch Operation It is possible to output the signal of each LED and FEED switch to external setting 3.4.1 Connector pin assignment (CN105) Connector: 53014-0510(Molex） Outer covering POWER LED ERROR LED FEED SW Main Board 1 CN105 Fig. 3-2 No. 1 2 3 4 5 5 Position of Main Board CN105 Connector pin assignment (CN105) Table 3-3 Signal Name Input/Output Function Power on circuit VCC － ( +5V） FEED SW Input FEED SW input － GND GND for signal POWER LED Output POWER LED output ERROR LED Output ERROR LED output Fig. 3-3 Opening/closing of the Main Board CN105 exists on the main board. The main board can be exposed by unscrewing one screw that fixes the main board cover and removing it by sliding it. - 26 - PMU2300ⅢSeries Product Specification 3.4.2 Precautions - Be sure to carry out the work after pulling out the paper, interface, and the power supply connector. - Take care not to clip cables etc. when you close the main board cover. - Be sure to close the main board cover after the work. Do not use the product when it is exposed. - The resistance (47Ω) has been attached to the LED of POWER and ERROR on the circuit side, however, be sure to attach the resistance according to the rating of LED to be used (the saturation voltage between collector and emitter of transistor is VCE (sat) = 0.3V (max) and the rated current is 100mA (max)). - For the FEED switch input terminal, refer to the circuit above. The ceramic capacitor is inserted on the circuit side for preventing the chattering, however, take note that the chattering becomes large depending on the switch. - Do not use the connector for any purpose other than the operation external output. The wrong usage may damage the printer and negatively affect the human body and the peripheral equipment etc. Control Board コントロールボード 3.3V VCC 3.3ｋΩ FEED FEED SW スイッチ GND GND 1000pF POWER POWER LED LED ERROR LED LED ERROR Fig. 3-4 Connection example - 27 - PMU2300ⅢSeries Product Specification 4 Interface 4.1 RS-232C Serial Interface 4.1.1 Connector PIN Assignment (CN301) No. 1 2 3 4 5 6 7 8 9 Table 4-1 Signal name NC RD TD DTR GND DSR RTS NC NC Connector PIN (CN301) Input/Output Function － Input Output Output － Input Output －－ No connection Receiving data Sending data Printer BUSY signal GND for signal Data set ready Printer BUSY signal No connection No connection Host 9pin Serial I/F Printer CN301 2 3 4 5 6 7 RD TD DTR GND DSR RTS TD RD DSR GND DTR CTS Fig. 4-2 Connectors available (D-Sub connector) 5 6 9 Fig. 4-1 CN301Connector Printer Cable Note : 17LE-23090-027 (DDK or its equivalent) : 17JE-13090-02 (DDK or its equivalent : RS-232C signal supports EIA RS-232C Host 25pin Serial I/F Printer CN301 2 3 4 5 6 7 3 2 6 5 4 8 １ RD TD DTR GND DSR RTS TD 2 RD 3 DSR 6 GND 7 DTR 20 CTS 5 9pin/25pin Serial I/F connection - If you make a connection to the interface other than 9pin/25pin serial I/F above, check the status of each signal and connect it correctly. 4.1.2 Specification Table 4-2 Item Synchronization Baud rate Per 1 word Signal polarity RS-232C Start bit Data bit Parity bit Stop bit Mark Space Specification Description Asynchronization 1200、2400、4800、9600、19200、38400、57600、115200bps (User selection) - For 1200, 38400, 57600, and 115200bps, only the setting by customized value are available. 1 bit 7 or 8 bit (User selection) Odd, even or no parity (User selection) 1 bit or more (User selection) Logic "1"(-3V~-12V) Logic "0"(+3V ~+12V) - 28 - PMU2300ⅢSeries Product Specification 4.1.3 Description of Input/Output Signals 1) Input/Output Signals Table 4-3 Input/Output Signals Signal Function name RD Receiving Data The unstable TD signal generated at host power start-up (shut-down), etc., under host connected, shall be a break signal and its data is discarded. (Unstable status happens on TD when cutting off the host power. Avoid printing characters after collecting.) TD Transmit Data DSR Transmit data after confirming the signal is space in case of selecting DTR/DSR control. Enables switching valid/invalid by the setting (MSW1-7) Transmit data ignoring DSR when XON/XOFF control is selected. DTR The printer is in BUSY status by Space. Mark enables printer to Receive Ready RTS condition. The condition to be BUSY is selectable by the setting, (MSWI-3,). № Status to be DTR 1 From Reset (including reset by NV memory write command, I/F signal and Test Print Command) or just after Power ON to Printer Ready status 2 During Self Printing is performing 3 Status of Input Buffer-Full (Refer to Buffer-Full Status) 4 During Platen is Open 5 During New Line operation by FEED Switch 6 Waiting FEED Switch Depression at Macro Execution 7 Status, Empty Paper 8 Status, Error At the above status, 1 through 3, it will be BUSY regardless of memory switch setting. No BUSY status happens in other cases. Note: When XON/XOFF control is selected, however, it will be Mark Status for the status1and 2, while it will be Space Status for other status at any time. This is used to know the connection status between printer and host. The status other than item 3 is defined as off-line. XON/XOFF Output Condition № XON Transmission 1 Time from Reset (including reset by NV memory write command, I/F signal, Test print Command) or just after power-on to Printer Operation Ready status. When the input buffer-full status is cancelled. But does not output when the printer is off-line even if the memory switch setting is off. When off-line changed to on-line. But does not output when buffer-full status. 2 3 № XOFF Transmission 1 When the input buffer becomes buffer-full status. 2 When on-line changed to off-line. But does not output when buffer-full status - 29 - PMU2300ⅢSeries Product Specification 2) Buffer-Full Status Buffer-full status is defined when the remained capacity of input buffer becomes the following status: Setting Value 4K Bytes 46 Bytes Table 4-4 Input Buffer-Full Buffer-Full Cancel Remaining 384 Bytes Remaining 512 Bytes Remaining 16 Bytes Remaining 26 Bytes The received data is discarded when the remaining input-buffer capacity reached to zero. 3) Data Receive Error When any of the following error occurs, data is printed as "?" or read and discarded depending on the setting of MSW1-4. Parity error Framing error Overrun error Note: When a command accompanying flash ROM write is used, the printer may become BUSY (DTR) temporarily at write operation. In this case, as the printer cannot process anything, the transmitted data may possibly be discarded 4) Electrical Feature RS-232C Interface (SP3232 Equivalent) [Printer] Input (RD, DSR) Output (DTR, TD) Fig. 4-3 Electrical Feature - 30 - [Host] PMU2300ⅢSeries Product Specification 4.2 Bidirectional Parallel Interface (IEEE1284) 4.2.1 Connector PIN Assignment (CN401) Connector: 53313-2065 (Molex) No. 10 1 20 11 Fig. 4-4 CN401Connector 1 2 3 4 5 6 7 8 9 10 Table 4-5 Connector PIN Assignment (CN401) Input/Output Signal name No. Input/Output Input nSTB 11 Output Input/Output DATA0 12 Output Input/Output DATA1 13 Output Input/Output DATA2 14 Input Input/Output DATA3 15 Input Input/Output DATA4 16 Output Input/Output DATA5 17 Input Input/Output DATA6 18 － Input/Output DATA7 19 － Output nACK 20 － Signal name BUSY PE SELECT nAUTOFD nINIT nFAULT nSELECTIN GND GND ＋5V 4.2.2 Supplied I/F wiring cable specification Table 4-6 Item Used housing Used terminal Used cable Cable length Cable specification Description 51089-2005 50212 (Molex) AWG26 (UL1007) and other equivalent product 300mm (tip is cut off) 4.2.3 Parallel port connection Printer CN401 Host 36pin Parallel I/F Fig. 4-5 Printer CN401 Host 25pin Parallel I/F 36pin/25pin Parallel port connection - If you make a connection to the connector other than above, check the status of each signal and connect it correctly. - 31 - PMU2300ⅢSeries Product Specification ② ① Fig. 4-6 Opening and closing of main board cover CN401 exists on the main board. The main board can be exposed by unscrewing one screw that fixes the main board cover and removing it by sliding it. * Precautions - Be sure to carry out the work after pulling out the paper, interface, and the power supply connector. - Pull out the wiring external using the space ①. - After the wiring, fix the cable with a banding band etc. using the hole ② preventing the cable from being pulled from external. - Take care not to clip cables etc. when the cover is closed. - After the work, be sure to close the main board cover and do not use the product when it is exposed. - Do not use CN401 for any purposes other than communication. The wrong use may damage the printer and negatively affect the human body and the peripheral equipment etc. - 32 - PMU2300ⅢSeries Product Specification 4.2.4 Specification 1) Compatibility Mode (host machine → printer communication: conforms to Centronics) (1) Outline The Compatibility Mode defines the Centronics interface that has been widely used. (2) Specifications Table 4-7 Item Data transfer method Synchronous system Handshake Signal level Specification Description 8-bit parallel by externally supplied nSTROBE signal by nACK signal and Busy signal all signals are TTL compatible 2) Reverse Mode (printer → host machine communication) The transfer of status data from this printer to the host machine is implemented in Nibble or Byte Mode. [1] Outline This mode defines the data transfer from the asynchronous printer controlled by the host machine. The data transfer in Nibble Mode is implemented using the existing control line and the data is transferred by 4-bit (Nibble) unit. In Byte Mode, 8-bit data line is transferred by changing it to bidirectional. In each case, the communication cannot be executed at the same time as Compatibility Mode, so the communication becomes half-duplex. [2] Precautions The first "n" of signal name indicates "LOW" active signal. If even one signal above is omitted, the bidirectional communication cannot be performed. For each signal line for the interface, be sure to use the twisted pair line and connect the return side to the signal ground level. Every interface condition is based on TTL level and fulfills following characteristics. The rising and falling time of each signal should be 0.5μs. The data transfer by ignoring nAck signal or BUSY signal should not be implemented. If such a signal is ignored, the data may be discarded. The length of the interface cable should be minimum distance. - 33 - PMU2300ⅢSeries Product Specification 4.2.5 Description of Input/Output Signals 1) Input/Output Signals Description of Input/Output signals [1] Input/Output signals (Compatibility Mode) (1) Input signal to the printer Table 4-8 Input Signal DATA0 to 7 nSTROBE nINIT Input signal to the printer Function 8-bit parallel signal (positive logic) Strobe signal for reading 8-bit data (negative logic) Implements the reset using nINIT signal in Compatibility Mode (Can be disabled depending on the setting: MSW3-3) nSELECT IN nINIT 50ms or more Fig. 4-7 nINIT Input signal nSELECT IN Signal that sets "HIGH" when shifting to IEEE1284 mode (negative logic) However, the reset signal is invalid for nSELECT IN/1284-Active "H". - 34 - PMU2300ⅢSeries Product Specification (2) Output signal from the printer Table 4-9 Output signal from the printer Signal name Function nACK 8-bit data request signal (negative logic) BUSY Signal that indicates BUSY status of the printer № 1 2 3 4 5 6 7 8 SELECT nFAULT PE Status to be BUSY From Reset (including reset by NV memory write command, I/F signal and Test Print Command) or just after Power ON to Printer Ready status During Self Printing is performing Status of Input Buffer-Full (Refer to Buffer-Full Status) During Platen is Open During New Line operation by FEED Switch Waiting FEED Switch Depression at Macro Execution Status, Empty Paper Status, Error At the above status, 1 through 3, it will be BUSY regardless of memory switch setting. No BUSY status happens in other cases Always active ("HIGH") Signal that sets "LOW" in the error status of the printer (negative logic) Paper out status. Signal that is output in the near-end status (depending on the command setting) (positive logic) Precautions When a command accompanying flash ROM write is used, the printer may become BUSY (DTR) temporarily at write operation. In this case, as the printer cannot process anything, the transmitted data may possibly be discarded. [2] Power supply-related Table 4-10 Signal name +5VDC GND FG Power supply-related signal Function 5V that is pulled up by 3.3kΩ of resistance. GND for signal (common ground on the circuit) Security grounding (case ground) - 35 - PMU2300ⅢSeries Product Specification 2) Electric characteristics [1] Input signal level (nStrobe, Data0 to 7) Every input signal is at C-MOS level. Table 4-11 Input signal level Signal name ”HIGH ”level DATA line 2.0V MIN Other than DATA line 3.5V MIN ”LOW ”level 0.8V MAX 1.5V MAX [2] Output signal level Every output signal is at C-MOS level. Signal name Table 4-12 Output signal level ”HIGH ”level ”LOW ”level DATA line Other than DATA line 4.4V MIN 4.9V MIN 0.1V MAX 0.1V MAX [3] Input/Output condition The input/output signal excluding STB signal is pulled up at 3.3KΩ. ※The STB signal is pulled up at 1.2KΩ. Input ［Host］［Printer］ Vcc 3.3KΩ Twisted pair line Vcc Output 3.3KΩ Fig. 4-8 Twisted pair line Input/Output condition - 36 - PMU2300ⅢSeries Product Specification 3) Buffer-Full Status Buffer-full status is defined when the remained capacity of input buffer becomes the following status: Table 4-13 Buffer-Full Setting Value 4K Bytes 46 Bytes Buffer-Full Cancel Remaining 384 Bytes Remaining 16 Bytes Remaining 512 Bytes Remaining 26 Bytes The received data is discarded when the remaining input-buffer capacity reached to zero. 4) Sending the status from the printer The printer can send the status in Reverse Mode (Nibble/Byte) (GS a, DLE EOT n, GS r, GS I commands are used) - The send buffer of the printer is 99 bytes. The host machine side should shift to Reverse Mode to prevent the absence of status. If ASB is used, Reverse Idle status is desirable; however, if it is not possible, whether there is send data of the printer should be monitored at all time. The ASB status that is accumulated without being sent is collectively (OR) sent with the latest status. - Each of the status information can be identified as follows. Table 4-14 Identification of status Command, code GS I GS r XON XOFF DLE EOT ASB (first byte) ASB (second byte) - 37 - Status <0**0****>B <0**0****>B <00010001>B <00010011>B <0**1**10>B <0**1**00>B <0**0****>B PMU2300ⅢSeries Product Specification 4.3 USB INTERFACE 4.3.1 Connector PIN assignment (CN201) Plug B Series Table 4-15 Connector PIN assignment (CN201) 1 2 4 3 No. 1 2 3 4 Signal name VBus(+5V) -Data(D-) +Data(D+) GND Fig. 4-9 CN201Connector ※Do not use cable exceeding 5m 4.3.2 Specification Item Whole Specification Communication Speed Communication Method Power Supply Table 4-16 Specification Description Based on the specification of USB2.0. USB full-speed mode (12M bps) USB bulk forwarding method 0ｍA (all supplied from the printer main unit) Memory switch setting for selecting USB mode is as follows No. MSW5-3 Table 4-17 USB Mode Memory switch setting Function OFF USB Mode ON Virtual COM* Printer Class ■･･･Default(factory setting) * The USB port of PC mounted on Windows is operated as a virtual COM port (RS-232C communication port) by the virtual COM driver. * Flow control can be selected from memory switch MSW7-7. No. MSW7-7 Table 4-18 VCom flow control Memory switch setting Function Setting VCom Protocol PC Setting DTR/DSR XON/XOFF ― ■･･･Default(factory setting) - 38 - PMU2300ⅢSeries Product Specification 5 Place of destination The setting for each place of destination is shown below. The difference of function depending on the place of destination is only the difference of setting of "5.1 Memory switch" 5.1 Memory switch The default setting of memory switch for each place of destination is shown below. Table 5-1 Destination J:Domestic U:N.America/W.Euro Destination MSW9-1 Code page Katakana PC437 Memory switch setting MSW9-2 MSW9-3 Int’l character Kanji Japan Valid U.S.A Invalid 5.2 Serial connector screw For the serial I/F specification, the connector screw varies depending on the place of destination. It is a factory option and cannot be changed by a user. Table 5-2 Serial I/F connector screw Destination Model name J:Domestic PMU2300Ⅲ□□-□□J□□ U:N.America/W.Euro PMU2300Ⅲ□□-□□U□□ １ 5 6 9 Screw Screw Mm Inch Screw Fig. 5-1 CN301Connector (Serial I/F) 5.3 ROM version The ROM version name is determined depending on the place of destination as shown below. It is a factory option and cannot be changed by a user. Table 5-3 Destination ROM version Destination ROM version J:Domestic DC20-XXXX U:N.America/W.Euro DC21-XXXX - Variance depending on the ROM version applies only in self printing (SeeP23). - 39 - PMU2300ⅢSeries Product Specification 6 Paper holder unit / kit: option - There are two types of paper holder as shown below. - The selectable paper insertion direction varies depending on the type of paper holder. 1) Horizontal paper insertion holder kit for maximum paper diameter Φ102mm: PHU-102S (part number: ZF98901) Paper Shaft Attach the paper shaft at this position Attach the PNE sensor at this position PNE Sensor 2) Vertical paper insertion holder kit for maximum paper diameter Φ203mm: PHU-203T (part number: ZF98903） - 40 - PMU2300ⅢSeries Product Specification 6.1 Paper Insertion Direction The paper insertion direction for each paper holder is shown below. * For 2) PHU-203T, which is the upper insertion type, the printer main unit and the paper shaft are connected with a chain for preventing the paper shaft from being lost. 1) Horizontal paper insertion holder kit for PHU maximum paper diameter Φ102mm: PHU-102S (part number: ZF98901) Paper insert direction: Left insertion Paper insert direction: Right insertion 2) Vertical paper insertion holder kit for PHU maximum paper diameter Φ203mm: PHU-203T (part number: ZF98903） - 41 - PMU2300ⅢSeries Product Specification 6.2 Paper holder attachment position The paper holder attachment position to the printer main unit varies depending on the paper diameter / insertion direction as shown in the table below. * The paper holder is attached in the direction of figure in Table 6-1 for Figure 6-1 Paper holder attachment position. (3) (2) (1) (1) Left side (2) (3) Right side Fig. 6-1 Paper holder attachment position Table 6-1 Left side Paper diameter/ Insertion direction 1: φ102mm/Left Paper holder attachment position (3) (2) Right side (1) －－ 2:φ102mm/Right (1) Left side Insertion direction (3) - 42 - －－ Right side (1) 3: φ203mm/Upper (3) －－ Paper diameter/ (2) (1) (3) PMU2300ⅢSeries Product Specification 6.3 PNE (Paper near end ) Sensor 6.3.1 Installation position [1] Maxim mum paper diameter Φ102mm Horizontal paper insertion holder kit: PHU-102S Left insertion (same as right insertion) Fig. 6-2 PNE sensor installation position - The factory-setting position of PNE sensor is "scale that is second closest to shaft". - The PNE sensor is connected to the main board connector CN108. [2] Maximum paper diameter Φ203mm Vertical paper insertion holder kit: PHU-203T Fig. 6-3 PHU-203T PNE sensor setting position - The factory-setting position of PNE sensor is "scale that is second closest to shaft". - The PNE sensor is connected to the main board connector CN108. Main Board CN108 3 I/F Fig. 6-3 Opening/Closing the main board cover - 43 - 1 Power Figure 6-4 Position of main board CN108 PMU2300ⅢSeries Product Specification 6.3.2 Memory Switch Setting Mode PNE sensor can be set to Valid/Invalid with MSW2-8 Table 6-2 Function PNE sensor No. MSW2-8 Memory switch OFF ON Valid Invalid ■･･･Default(factory setting) 6.3.3 Adjustment method As the position of PNE sensor can be set at an arbitrary position, use the product by setting it to the optimum position. Loosen the screw slightly, and then slide the position of the PNE sensor (use △ mark and scale as a guide). If you decide the detection position, tighten the screw. ① ② ③ ① ② ③ Fig. 6-6 PHU-102S scale position / adjustment method Fig. 6-7 PHU-203T scale position/ adjustment method ク Fig. 6-8 △mark ① ② ③ Table 6-3 Scale position of PNE sensor External diameter of paper remaining amount Scale position when it is detected by PNE sensor (reference) Scale that is 1st closest to shaft φ32 Scale that is 2nd closest to shaft φ37 Scale that is 3rd closest to shaft φ42 - 44 - PMU2300ⅢSeries Product Specification 6.3.4 Precautions - The PNE sensor may malfunction due to ambient light, so when you use the PNE sensor, consider the installation of light shielding cover etc. for preventing the ambient light from entering. - The value of "external diameter roof roll paper when it is detected by PNE sensor" varies depending on the model and the type of roll paper, so use it as a referential value. - The paper near-end may be detected at the position that is not near the external diameter of roll paper shown above, so adjust the installation position in that case. - Do not use the PNE sensor other than that is made by our company. The wrong use may damage the printer and negatively affect the human body and peripheral equipment etc. - 45 - PMU2300ⅢSeries Product Specification 7 Function selection With this control board, some function can be set by default for using it. 7.1 Dip switch (serial interface) ON 1 2 3 5 4 6 7 8 Fig.7-1 Dip switch (SW301) The DIP switch is installed on the board with serial interface specification only. Turn the power OFF when changing the DIP switch setting Table 7-1 DIP switch ON No. Function DSW-1 Communication condition setting method Priority on DIP switch Priority on Memory switch DSW-2 Handshake XON／XOFF DTR／DSR DSW-3 7 bits With parity 8 bits DSW-4 Bit length Parity check DSW-5 Parity selection Even parity Odd parity DSW-6 DSW-7 DSW-8 Baud rate selection OFF None See Selecting Baud Rate table. Reserved Fixed ■･･･Default(factory setting) － Table 7-2 Baud rate Selecting Baud Rate No. DSW-6 DSW-7 2400 bps 4800 bps 9600 bps 19200 bps OFF OFF ON OFF OFF ON ON ON ■･･･Default(factory setting) Baud rate settings (1200 bps、38400 bps、57600 bps、115200 bps) other than the above can be changed by memory switch setting. - 46 - PMU2300ⅢSeries Product Specification 7.2 Memory Switches Memory switch is a generic name for the following: - Memory switches MSW1、MSW2、MSW3、MSW4、MSW5、MSW11、MSW12 - Customize value, Communication condition for Serial I/F 1) Memory switches MSW1、MSW2、MSW3、MSW4、MSW5、MSW11、MSW12 Table 7-3-1 Memory Switch Setting No. Function OFF ON MSW1-1 Power ON Info Valid Not Send MSW1-2 Buffer Size 4K bytes 45 bytes MSW1-3 Busy Condition Full /Err Full MSW1-4 Receive Error Print “?” No Print MSW1-5 CR Mode Ignored LF MSW1-6 Reserved Fixed — MSW1-7 DSR Signal Invalid Valid MSW1-8 Reserved Fixed — MSW2-1 Reserved — Fixed Invalid Valid MSW2-2 *1 Auto Cutter MSW2-3 Spool Print Invalid Valid MSW2-4 Full Col Print Line Feed Wait Data MSW2-5 Resume aft PE Next Top MSW2-6 Reserved Fixed — MSW2-7 Reserved Fixed — MSW2-8 PNE Sensor Valid Invalid MSW3-1 Resume Cttr Err Valid Invalid MSW3-2 Reserved Fixed — MSW3-3 Parallel 31 Pin Valid Invalid MSW3-4 *2 Black MK MSW3-5 Column Number Thermal 48 col MSW3-6 Reserved Fixed — MSW3-7 CBM1000 Mode Invalid Valid MSW3-8 Resume Open Err MSW4-1 Auto Length Close Invalid MSW4-2 Auto Loading Invalid Valid Valid MSW4-3 Feed&Cut at TOF Invalid Valid MSW4-4 Reserved Fixed — MSW4-5 Reserved Fixed — MSW4-6 Reserved Fixed — MSW4-7 Reserved Fixed — Invalid Valid MSW4-8 Paper Select Partial Only *3 - 47 - 42 col Command PMU2300ⅢSeries Product Specification No. Function OFF MSW5-1 Reserved Fixed ON — MSW5-2 Reserved Fixed — MSW5-3 USB Mode Virtual COM MSW5-4 Reserved Fixed Printer Class — MSW5-5 Reserved Fixed — MSW5-6 Speed / Quality Speed Quality MSW5-7 Reserved Fixed — MSW5-8 Reserved Fixed — Invalid Valid MSW11-1 Presenter *4 MSW11-2 Retract Function Invalid Valid MSW11-3 Retract Direction Rear Front MSW11-4 Store and eject Invalid Valid MSW11-5 No print with paper Invalid Valid MSW11-6 Min Receipt Length 75mm 120mm MSW11-7 Reserved Fixed ― MSW11-8 Reserved Fixed ― MSW12-1 Bezel Function *5 Invalid Valid MSW12-2 LED Control Valid MSW12-3 Reserved Invalid Fixed MSW12-4 Reserved Fixed ― MSW12-5 Show Error by LED Invalid Valid MSW12-6 No print with paper Valid MSW12-7 Reserved Invalid Fixed Reserved Fixed ― MSW12-8 ― ― ■･･･Default(factory setting) * 1: When the presenter function is set to valid (MSW11-1=ON), the full cut operation is carried out regardless of the setting of auto cutter operation (MSW2-2). * 2: The default setting of the paper selection varies depending on the model. Standard: OFF (Thermal) black mark specification: ON (Black MK) * 3: When the presenter function is set to valid (MSW11-1=ON), the full cut operation is carried out regardless of the setting of forcible partial (MSW4-8). * 4: The default setting of the presenter function varies depending on the model. presenter is not attached: OFF (invalid) presenter is attached: ON (valid) * 5: The default setting of the bezel function varies depending on the model. bezel is not attached: OFF (invalid) bezel is attached: ON (valid) - 48 - PMU2300ⅢSeries Product Specification 2) Customize value Customize value can be set by the GS ( E command. No. MSW7-1 Table 7-4-1 Function Baud Rate MSW7-2 Data Length MSW7-3 Stop Bit MSW7-4 Parity MSW7-5 Flow Control MSW7-6 Reserved MSW7-7 VCom Protocol MSW9-1 Code page Communication condition for Serial I/F Value 1200bps 4800bps 2400bps 9600bps 19200bps 38400bps 57600bps 115200bps 7 bits 8 bits 1 bit 2 bit NONE ODD EVEN DTR/DSR XON/XOFF — — PC Setting XON/XOFF DTR/DSR — PC437 Katakana PC850,858 PC860 PC863 PC865 PC852 PC866 PC857 WPC1252 Spacepage PC864 Thai MSW9-2 Int’Char Set MSW9-3 Kanji MSW9-4 JIS/ShiftJIS U.S.A France Germany England Denmark Sweden Italy Spain Japan Norway Denmark2 Spain2 Latin America Korea Croatia China - 49 - Valid Invalid JIS ShiftJIS PMU2300ⅢSeries Product Specification Table 7-4-2 Communication condition for Serial I/F No. Function Value MSW10-1 Print Density 70％ 75％ 80％ 85％ 90％ 95％ 100％ 105％ 110％ 115％ 120％ 125％ 130％ 135％ 140％ MSW10-2 Print Speed Level 1 Level 2 Level 3 Level 4 Level 4 Level 6 Level 7 Level 8 Level 9 MSW10-3 Reserved ― ― ■･･･Default(factory setting) MSW9-1, 9-2, 9-3 vary with destination - 50 - PMU2300ⅢSeries Product Specification 8 SET UP 8.1 Component Names 8.1.1 When the Presenter and bezel are not attached Printer mechanism Auto cutter Operation section FEED SW POWER LED ERROR LED Platen open lever Platen holder Printing head Tension bar FFC Main board cover Platen BM sensor (optional) DIP switch I/F (3types) Serial I/F Parallel I/F USB I/F Power connector - 51 - PMU2300ⅢSeries Product Specification 8.1.2 When the bezel is attached Bezel Bezel (For presenter) 8.1.3 Presenter section Cover unit Cover unit fixing screw Presenter unit Presenter roller Presenter paper detection sensor (when the cover is removed) Presenter paper retract sensor - 52 - PMU2300ⅢSeries Product Specification 8.1.4 Paper holder (optional) Paper shaft Dumper PNE sensor Shaft stopper Cord holder - 53 - PMU2300ⅢSeries Product Specification 8.2 Precautions 8.2.1 Failure 1) Never open the printer cover during printing and while the cutter is in operation. Otherwise, it may result in injury, printer or auto cutter may be broken. 2) Note that static electricity on thermal head may cause breakage of driver IC, etc. Ensure that ground wire connection is properly made 3) Do not remove paper with printer cover closed. 4) As thermal head heater and driver IC are easy to break, do not contact metal and sand paper to them. 5) Do not block the paper exit. Never hold the paper during printing. 6) Do not print in the state where moisture is present on the head surface due to condensation, etc. 7) Set the roll paper properly not to generate bending. 8) Use the printer under stable condition without any vibration. 8.2.2 Print quality 1) In the case of intermittent printing where printing and paper feeding is interrupted by the status of waiting for data coming from the host, paper feed may sometimes be disordered in the 1 to 3 dot lines from the start of printing. Especially, care must be taken when printing graphics or the like. 2) If you set the paper and close the platen holder, the printer feeds the paper by a few dots and then cut the paper. The cutting operation is not executed when MSW4-3 is turned OFF (paper head alignment cutting invalid). 3) Never touch the heater of the head. Touching the heater by hand may cause degrading of print quality due to soiled head. 4) Use of paper not recommended may be a disclaimer of warranty in print quality or life of thermal head. Especially, inclusion of "Na+, K+, Cl−" in the component of recording paper may degrade the life of thermal head remarkably. 5) To close the platen holder, hold the center or both ends and close securely. Closing the cover with one end pressed may cause incomplete closing resulting in uneven printing. - 54 - PMU2300ⅢSeries Product Specification 8.2.3 Safety 1) Never touch the head by hand just after printing as it is heated during printing. Otherwise, there is a risk of burn. 2) Use care in handling the edged part (especially cutter blade) of the components of the printer. Erroneous handling may cause injury. 3) Do not insert hand into the exit of paper not only during printing but also when the printer is not operating. 4) Do not hold the parts shown below. FFC Gear cover Tension bar Bezel Cutter cable Sensor Gear Motor Static Eliminator Brush Paper shaft Dumper Shaft stopper PNE sensor cable Fig. 8-1 Keep your hands off 8.2.4 Others 1) This product uses plated sheet steel and may cause rust in the edge section. This will not affect the printer’s function. - 55 - PMU2300ⅢSeries Product Specification 8.3 How to Set Paper (Replacement) Follow the steps below to replace paper. 8.3.1 Paper Holder: PHU-102S 1) Remove shaft stopper. If paper core is remained, pull out the core. 3) After confirming the winding direction of paper, insert the core into the paper shaft to the position getting over a guard and press-in shaft stopper securely until it is locked. 2) In case if the end of paper for replacement is not aligned, cut straight cleanly with scissors, etc. 4) Insert the paper end into paper inlet. Automatic loading is started. (Automatic loading does not start when MSW4-2 is OFF) Caution - Be sure to use designated paper - If you use paper other than designated, there may be the case of printing quality and life, etc, are not guaranteed. - Set paper straight without any slackness - 56 - PMU2300ⅢSeries Product Specification 8.3.2 Paper Holder: PHU-203T 1) After confirming the winding direction of paper, insert the paper core into the paper shaft and set the paper shaft to the U-shaped gutter of paper holder. 2) In case if the end of paper for replacement is not aligned, cut straight cleanly with scissors, etc. Tension Bar 3) Insert the paper end into paper inlet after slipping through underneath of tension bar. Automatic loading starts. (Automatic loading does not start when MSW4-2 is OFF) Caution - Be sure to use designated paper - If you use paper other than designated, there may be the case of printing quality and life, etc, are not guaranteed.Set paper straight without any slackness. - 57 - PMU2300ⅢSeries Product Specification 8.4 How to Release Cutter Lock (Cutter Error) Follow the steps below to release cutter lock (cutter error). 1) Turn the power OFF, rotate the cutter motor with driver and store the cutter blade. 3) Remove the cause of cutter lock such as paper jam. 2) Open platen holder. Pay attention no to place fingers underneath to avoid nipping. 4) Close the platen holder. Securely press until it locks, then turn the power ON and set the paper again. Caution - Pay sufficient attention not to touch the blade part of cutter because there is the case of moving blade of cutter being jumped out. - Pay attention not to touch the print head with hands because the head becomes high temperature just after printing. - Do not touch the surface of print head heating element with bare hands, metal, etc. - 58 - PMU2300ⅢSeries Product Specification 8.5 How to Remove Paper Jam Follow the steps below to remove paper jam. 8.5.1 When Presenter is not installed 1) Turn the power OFF and cut the paper. 2) Open platen holder and remove the cause of paper jam. 4) Turn the power ON and set the paper again. 3) Close the platen holder. Press the holder securely until it locks. Caution - Be sure to conduct paper jam removal after the power being OFF. - Pay attention not to touch the print head with hand because the head becomes high temperature just after printing. - Do not touch the surface of print head heating element with bare hands, metal, etc. - 59 - PMU2300ⅢSeries Product Specification 8.5.2 Presenter Installed 2) Open platen holder and remove the cause of paper jam. 1) Turn the power OFF and cut paper. 3) Remove locking screw for cover unit by turning the screw. 4) Slide the cover unit to the arrow mark direction and release the lock. Caution - Be sure to conduct paper jam removal after the power being OFF. - Pay attention not to touch the print head with hand because the head becomes high temperature just after printing. - Do not touch the surface of print head heating element with bare hands, metal, etc. - 60 - PMU2300ⅢSeries Product Specification 5) Remove the cover unit. 6) Remove the cause of paper jam. 7) Close the platen holder. Press-in securely 9) Turn the power ON and set the paper until it locks. again. 8) Load the cover unit by sliding with the opposite procedures of removing and fix the cover unit by turning the locking screw. Caution - Be sure to conduct paper jam removal after the power being OFF. - Pay attention not to touch the print head with hand because the head becomes high temperature just after printing. - Do not touch the surface of print head heating element with bare hands, metal, etc. - 61 - PMU2300ⅢSeries Product Specification 8.6 Function of Presenter This printer has the function of recovering paper automatically after ejection. This function is transferable between valid and invalid with memory switch. - After cutting printed paper, the function recovers paper after certain time passed under the status of recovery sensor detecting paper. - If cut command is executed with the status of printing contents not reaching to minimum issue length, add the minimum paper feed length and conducts full cut. - The recovery time is able to be set by a command. - In case of conducting paper recovery, secure the paper path on the equipping surface and underneath of the main body, and prepare a recovery box. Please refer to 9.7 “Installation” on page 74 for details. *Refer to Command Reference for details of each command. 8.6.1 Memory Switch Setting Setting of presenter function is capable with MSW11. 1) MSW11-1 Function : Presenter : Selects the valid/invalid of presenter function. Operation at OFF (Invalid): Let the presenter function to be invalid. The setting of MSW11-2～MSW11-6 becomes invalid Operation at ON (Valid): Let the Presenter function to be valid The setting of MSW11-2～MSW11-6 becomes valid. 2) MSW11-2 Function : Retract Function : Selects the valid/invalid of recovery operation. Operation at OFF (Invalid): Let the recovery operation to be invalid Operation at ON (Valid): Let the recovery operation to be valid. After ejecting paper, the function performs paper recovery of forward ejection or rear side recovery after a certain time passed with the setting of MSW11-3 (Retract Direction). By the execution of Receipt Recovery Command GS R 0, conducts instant recovery operation. - The recovery time is able to be set with the Setting Command, GS ( E, of customized value. Also, the recovery time until power being OFF is changeable with the setting command, GS R 1, of the Receipt Recovery Timer value. Initial Value of Recovery Time: 5s 3) MSW11-3 Function : Retract Direction : Selects recovery direction at Recovery Operation Valid (MSW11-2 = ON) Operation at OFF (Rear): Recovers paper from rear side. Operation at ON (Forward): Ejects paper forward. 4) MSW11-4 Function : Store and eject : Selects valid/invalid of ejection after accumulation. Operation at OFF (Invalid): When paper is reached to Presenter Roller, synchronizes with printing line-feed without paper sagging and conducts paper ejection. Operation at ON (Valid): Paper ejection does not occur even when the paper reaches to the Presenter Roller and conducts paper ejection after paper sagging of maximum 220 mm. - 62 - PMU2300ⅢSeries Product Specification 5) MSW11-5 Function : No print with paper : When recovery sensor is detecting paper, selects valid/invalid of the next printing/ejecting operation. Operation at OFF (Invalid): Even when the recovery sensor detects paper, conducts the next printing/ejection operation. Operation at ON (Valid): When the recovery sensor is detecting paper, waits the next printing/ejection operation until the sensor fails to detect paper. 6) MSW11-6 Function : Min Receipt Length : Selects minimum receipt length. Operation at OFF (75mm): Sets the minimum length at 75mm. Operation at ON (120mm): Sets the minimum length at 120mm. - 63 - PMU2300ⅢSeries Product Specification 8.7 Bezel function This printer is equipped with a function for controlling the bezel LED during standby / printing / discharge. This function can be switched to valid / invalid using the memory switch. - For the bezel, two types; for main unit and for presenter are available. For the bezel for the main unit, the bezel paper detection sensor is attached in the bezel and the paper can be detected. * For details on each command, refer to the command reference. 8.7.1 Memory switch setting The bezel function can be set by MSW12. 1) MSW12-1 Function : Bezel Function : Validity / invalidity of bezel function is selected. Operation at OFF (invalid): The bezel function is disabled Setting of MSW12-2 to MSW12-6 is disabled. Operation at ON (valid): The bezel function is enabled. Setting of MSW12-2 to MSW12-6 is enabled. 2) MSW12-2 Function : LED Control : Validity / invalidity of bezel LED control (during standby / during printing / during discharge) is selected. Operation at OFF (invalid): The bezel LED control is disabled. Operation at ON (valid): The bezel LED control is enabled. - The bezel LED display status, bezel lighting time during standby, and bezel blinking time can be set by setting of customized value GS ( E command. Initial value of bezel LED display During standby: OFF During printing: lights up During discharge: blinks Initial value of bezel lighting time during standby 0: continuously lights up Initial value of Bezel blinking ON/OFF time 5: 500ms - The bezel LED display can be changed by contlolling bezel LED command GS R 2 regardless of setting of MSW12-2. 3) MSW12-5 Function : Show Error by LED : Validity / invalidity of LED abnormal display is selected. When an error is generated, the bezel LED is displayed by synchronizing it with the error LED. Operation at OFF (invalid): LED abnormal display is disabled. Operation at ON (valid): LED abnormal display is enabled. 4) MSW12-6 Function : No print with paper : When the bezel paper detection sensor detects the paper, validity / invalidity of next printing / discharge operation is selected. This function becomes effective only when the bezel for the main unit is attached. Operation at OFF (invalid): Even if the bezel paper detection sensor detects the paper, the next printing / discharge operation is carried out. Operation at ON (valid): If the bezel paper detection sensor detects the paper, the next printing / discharge operation is carried out after the sensor does not detect the paper. - 64 - PMU2300ⅢSeries Product Specification 8.8 Maintenance 1) Periodical cleaning of thermal head, platen unit, presenter roller, and cover unit - If dust or paper powder is attached to the thermal head, platen unit, presenter roller, and cover unit, the troubles such as printing quality loss and paper feed failure are caused. In order to use this product long, it is recommended to clean up the thermal head, platen unit, presenter roller, and cover unit periodically. 2) Index of cleaning implementation cycle - Platen unit, presenter roller, cover unit For every 10km of printing distance, or once a month - Thermal head As occasion demands when the printing quality descends 3) Cleaning method - Turn OFF the power supply and wipe off the dirt attached to the surface of heating element of head, presenter roller, surface of platen rubber part, and cover unit with a cotton applicator dipped with ethanol. Precautions - As the temperature of the print head is high immediately after the printing, do not touch it. - Do not touch the surface of heating element of print head with bare hands or metal etc. - 65 - PMU2300ⅢSeries Product Specification 9 Dimensional Drawings 9.1 PMU2300ⅢSN Outline Drawings 1) Size (mm) :W113×H98×D182 2) Weight : Approx. 0.9kg 3) Outline drawing - 66 - PMU2300ⅢSeries Product Specification 9.2 PMU2300ⅢSB Outline Drawings (Bezel equipped model) 1) Size (mm) :W113×H98×D208 2) Weight :Approx.1.0kg 3) Outline drawing - 67 - PMU2300ⅢSeries Product Specification 9.3 PMU2300ⅢPN Outline Drawings (Presenter equipped model) 1) Size (mm) :W113×H98×D234 2) Weight :Approx.1.2kg 3) Outline drawing - 68 - PMU2300ⅢSeries Product Specification 9.4 PMU2300ⅢPB Outline Drawings (Bezel/Presenter equipped model) 1) Size(mm) :W113×H98×D260 2) Weight :Approx. 1.2kg 3) Outline drawing - 69 - PMU2300ⅢSeries Product Specification 9.5 PMU2300ⅢSB Outline Drawings (Bezel equipped) Holder PHU-102S attached - 70 - PMU2300ⅢSeries Product Specification 9.6 PMU2300ⅢPB Outline Drawings (Bezel/Presenter equipped)Holder PHU-203T attached - 71 - PMU2300ⅢSeries Product Specification 9.7 Installation - The printer should be installed on the flat surface (flatness 0.3 or less) with a sufficient strength. - Take care not to be injured by an edge of plate when you install the printer. - Do not move the printer by holding a weak part such as harness because it may cause an unexpected accident. - This printer should be secured by four screws (M3x6 to 10mm) at the position shown below. - If the printer main unit does not contact the metallic part when you install it, make the ground connection using the FG connection screw shown below. - When you install the wall (positionA indicated Fig 9-4), the wall inside should be smooth and flat face to not be caught by the edge of paper. Under lower temperature environment, paper jam may occur while rear paper collection as well as minimum length of ticket is set at 75mm. Set accordingly at 120mm. Refer to P62 “8.6 Function of Presenter”. Installation example Fig. 9-2 FG fixing screw position Fig. 9-1 PMU with Paper holder: PHU-102S Fig. 9-3 PMU with Paper holder: PHU-203T - 72 - PMU2300ⅢSeries Product Specification Allow a spacefor removal in the upper section of the cover unit Allow a space accordingly as indicated below (unit: mm) Center of paper (※) The dimension indicate paper retract forward mode. At Rear retract mode, keep height enough so as not to hinder the dropping paper. Also consider the accumulation of the dropping paper. Fig. 9-4 - 73 - PMU2300ⅢSeries Product Specification 10 PRINT CONTROL COMMANDS ○ Print Control Commands Control Command Function MODE LF Printing and paper feed S·P CR Back to printing S·P FF Printing in page mode and recovery P ESC FF Printing data in PAGE MODE P ESC J Printing and feeding paper in minimum pitch S·P ESC d Printing and feeding the paper by "n" lines S·P GS P { ○Print Character Commands Control Command Function MODE CAN Canceling print data in PAGE MODE ESC SP Setting the right spacing of the character S·P ESC ! Collectively specifying the printing mode S·P ESC % Specifying/canceling download character set S·P ESC & Defining the download characters S·P ESC - Specifying/canceling underline S·P ESC ? Deleting download characters S·P ESC E Specifying/canceling emphasis printing S·P ESC G Specifying/canceling double strike printing S·P ESC M Selection of character fonts S·P ESC R Selecting the international character set S·P ESC V Specifying/canceling 90°-right-turned characters ESC t Selecting the character code table ESC { Specifying/canceling the inverted characters GS ! Specifying the character size S·P GS B Specifying/canceling the black/white inverted printing S·P GS b Specifying/canceling the smoothing S·P - 74 - GS P P S S·P S { PMU2300ⅢSeries Product Specification ○Print Position Commands Control Command Function MODE GS P HT Horizontal tab S·P ESC $ Specifying the absolute positions S·P ESC D Setting horizontal tab position S·P ESC T Selecting the character printing direction in PAGE MODE P ESC W Defining the print area in PAGE MODE P { ESC \ Specifying the relative position S·P { ESC a Aligning the characters S GS $ Specifying the absolute vertical position of characters in PAGE MODE P { GS L Setting the left margin S { GS W Setting the print area width S·P { GS \ Specifying the relative vertical position of a character in PAGE MODE S·P { MODE GS P { ○Line Feed Span Commands Control Command Function ESC 2 Specifying 1/6-inch line feed rate S·P ESC 3 Setting line feed rate of minimum pitch S·P { MODE GS P ○Bit Image Commands Control Command Function ESC * Specifying the bit image mode S·P GS * Defining the download bit image S·P GS / Printing the downloaded bit image S·P GS v 0 Printing of raster bit image S ○Status Commands Control Command Function MODE DLE EOT Sending status in real-time S·P ESC u Sending the status of peripheral equipment S·P ESC v Sending printer status S·P GS a Enabling/disabling ASB (Automatic Status Back) S·P GS r Sending status S·P - 75 - GS P PMU2300ⅢSeries Product Specification ○Paper Detecting Commands Control Command Function MODE ESC c 3 Selecting the Paper Sensor valid for Paper-end signal output S·P ESC c 4 Selecting the Paper Near-end Sensor valid for print stop S·P GS P ○Panel Switch Commands Control Command ESC c 5 Function Enabling/disabling the panel switches MODE GS P S·P ○Macro Commands Control Command Function MODE GS : Starting/ending macro definition S·P GS ^ Executing the macro S·P GS P ○Cutter Commands Control Command Function ESC i Full cut command ESC m Partial cut command GS V Cutting the paper MODE GS P S·P ○Bar Code Commands Control Command Function MODE GS H Selecting of printing position of HRI characters S·P GS f Selecting the font of HRI characters S·P GS h Specifying the height of the bar code S·P GS k Printing the bar code S·P GS w Specifying the horizontal size of the bar code S·P GS P ○Two-dimensional code Commands Control Command GS (k Function Setting and printing of two-dimensional code MODE GS P S ○Commands for Flash Memory Control Command Function MODE FS p Printing the bit image in flash memory S FS q Defining the bit image in flash memory S - 76 - GS P PMU2300ⅢSeries Product Specification ○Kanji Control Commands Control Command Function MODE FS ! Collectively setting Kanji print mode S·P FS & Setting Kanji mode S·P FS - Setting/canceling Kanji underline S·P FS . Canceling Kanji mode S·P FS 2 Defining external character S·P FS C Selecting Kanji code system S·P FS S Setting Kanji space amount S·P FS W Setting/canceling four times enlargement of Kanji S·P FS ( A Setting font attribute of Kanji S·P ○Black mark control command Control Name command GS FF Printing the ejecting the black mark paper ○Printer setting command Control Name command GS ( D Validity / invalidity of real-time command GS ( E User setting command GS ( K Selection of printing control method GS ( M Customization of printer ○Special command Control command GS R 0 GS R 1 GS R 2 GS S Name Retracting receipt immediately Setting timer for auto receipt retraction Controlling bezel LED Detecting next black mark MODE GS P { GS P S•P MODE GS P S S S S MODE GS P S S S S ○Other Commands Control Command Function MODE DLE ENQ Real-time request to printer S·P DLE DC4 Outputting specified pulse in real-time S·P ESC = Data input control S·P ESC @ Initializing the printer S·P ESC L Selecting PAGE MODE S ESC S Selecting STANDARD MODE P GS ( A Execution of test printing S GS I Sending the printer ID S·P GS P Specifying the basic calculation pitch S·P ① In the Mode column: S = STANDARD MODE, P = PAGE MODE ② { = shows the command affected by GS P. - 77 - GS P PMU2300ⅢSeries Product Specification 11 CHARACTER CODE 11.1 Codepage 11.1.1 Codepage 00H to 7FH & PC437 (USA、Europe Standard) 0 0 1 NU L DL E XO N 1 2 3 4 5 XOF F EO T EN Q 6 7 8 DC 4 CA N 9 A B HT C D E F FF FS CR GS LF ES C RS 2 3 0 4 @ 5 P 6 ` 7 p 8 Ç 9 É A á B ░ C └ D ╨ E α F ≡ ! 1 A Q a q ü æ í ▒ ┴ ╤ β ± " # $ 2 3 4 B C D R S T b c d r s t é â ä Æ ô ö ó ú ñ ▓ │ ┤ ┬ ├ ─ ╥ ╙ ╘ Γ π ∑ ≧ ≦ ⌠ % 5 E U e u à ò Ñ ╡ ┼ ╒ σ ⌡ & ' ( 6 7 8 F G H V W X f g h v w x å ç ê û ù ÿ a o ¿ ╢ ╖ ╕ ╞ ╟ ╚ ╓ ╫ ╪ μ τ Φ ÷ ≈ ｡ ) * + 9 : ; I J K Y Z [ i j k y z { ë è ï Ö Ü ¢ ⌐ ¬ ½ ╣ ║ ╗ ╔ ╩ ╦ ┘ ┌ █ θ Ω δ · √ , . / < = > ? L M N O ¥ ] ^ _ l m n o | } ~ € î ì Ä Å £ ¥ ¼ ¡ « » ╝ ╜ ╛ ┐ ╠ ═ ╬ ╧ ▃ ▌ ▐ ▄ ∞ ∈ ∩ - 78 - Pt ƒ ⁿ ² ￭ PMU2300ⅢSeries Product Specification 11.1.2 Codepage 00H to 7FH & Katakana 0 0 1 NU L DL E XO N 1 2 3 4 5 XOF F EO T EN Q DC 4 6 7 CA N 8 9 A B HT C D E F FF FS CR GS LF ES C RS 2 3 0 4 @ 5 P 6 ` 7 p 8 ▁ 9 ┴ ! 1 A Q a q ▂ ┬ " # $ 2 3 4 B C D R S T b c d r s t ▃ ▅ ▆ % 5 E U e u & ' 6 7 F G V W f g ( 8 H X ) * + 9 : ; I J K , . / < = > ? L M N O E ═ F × アチム ╞ 円 ┤ ├ ─ ┌ イツメ ┘ ウテモ、エトヤ ╪ ╡ ◢ 年月日 ▇ ＿･オナユ ◣ 時 v w █ ▉ 秒 x ▏ ◥ ◤ ♠ 分 h ｜ヲカニヨ ▕ ァキヌラ ┌ ィクネリ Y Z [ i j k y z { ▎ ▍ ▌ ┐ └ ┘ ゥケノルェコハレォサヒロ ♥ ♦ ♣ 市区町 ¥ ] ^ _ l m n o | } ~ € ▋ ▋ ▊ ＋ ╭ ╮ ╰ ╯ ャュョッ ● ○ ╱ ╲ 村人 ▒ SP - 79 - A B C D SP －タミ º シスセソフワヘンホ “ マ゜〒 PMU2300ⅢSeries Product Specification 11.1.3 Codepage 00H to 7FH & PC850 (Multilingual) 0 0 1 NU L DL E XO N 1 2 3 4 5 XOF F EO T EN Q 6 7 8 DC 4 CA N 9 A B HT C D E F FF FS CR GS LF ES C RS 2 3 0 4 @ 5 P 6 ` 7 p 8 Ç 9 É A á B ░ C └ D ð E Ó F ― ! 1 A Q a q ü æ í ▒ ┴ Ð β ± " # $ 2 3 4 B C D R S T b c d r s t é â ä Æ ô ö ó ú ñ ▓ │ ┤ ┬ ├ ─ Ê Ë È Ô Ò õ ＝ ¾ ¶ % 5 E U e u à ò Ñ Á ┼ € Õ § & ' ( 6 7 8 F G H V W X f g h v w x å ç ê û ù ÿ a o ¿ Â À © ã Ã ╚ Í Î Ï μ þ Þ ÷ ) * + 9 : ; I J K Y Z [ i j k y z { ë è ï Ö Ü ø ® ¬ ½ ╣ ║ ╗ ╔ ╩ ╦ ┘ ┌ █ Ú Û Ù ¨ · ¹ , . / < = > ? L M N O ¥ ] ^ _ l m n o | } ~ € î ì Ä Å £ Ø × ƒ ¼ ¡ « » ╝ ¢ \ ┐ ╠ ═ ╬ ¤ ▃ ý ￤ Ý Ì ― ▄ ′ ³ ₂ ￭ - 80 - ゝ ° PMU2300ⅢSeries Product Specification 11.1.4 Codepage 00H to 7FH & PC860 (Portuguese) 0 0 1 NU L DL E XO N 1 2 3 4 5 XOF F EO T EN Q 6 7 8 DC 4 CA N 9 A B HT C D E F FF FS CR GS LF ES C RS 2 3 0 4 @ 5 P 6 ` 7 p 8 Ç 9 É A á B ░ C └ D ╨ E α F ≡ ! 1 A Q a q ü À í ▒ ┴ ╤ β ± " # $ 2 3 4 B C D R S T b c d r s t é â ã È ô õ ó ú ñ ▓ │ ┤ ┬ ├ ─ ╥ ╙ ╘ Γ π ∑ ≧ ≦ ⌠ % 5 E U e u à ò Ñ ╡ ┼ ╒ σ ⌡ & ' ( 6 7 8 F G H V W X f g h v w x Á ç ê Ú ù Ì a o ¿ ╢ ╖ ╕ ╞ ╟ ╚ ╓ ╫ ╪ μ τ Φ ÷ ) * + 9 : ; I J K Y Z [ i j k y z { Ê è Í Õ Ü ¢ Ò ¬ ½ ╣ ║ ╗ ╔ ╩ ╦ ┘ ┌ █ θ Ω δ , . / < = > ? L M N O ¥ ] ^ _ l m n o | } ~ € Ô ì Ã Â £ Ù ¼ ¡ « » ╝ ╜ ╛ ┐ ╠ ═ ╬ ╧ ▃ ▌ ▐ ▄ ∞ ∈ ∩ - 81 - Pt Ó ≈ ° · √ ⁿ ₂ ￭ PMU2300ⅢSeries Product Specification 11.1.5 Codepage 00H to 7FH & PC863 (Canadian-French) 0 0 1 NU L DL E XO N 1 2 3 4 5 XOF F EO T EN Q 6 7 8 DC 4 CA N 9 A B HT C D E F FF FS CR GS LF ES C RS 2 3 0 4 @ 5 P 6 ` 7 p 8 Ç 9 É A ￤ B ░ C └ D ╨ E α F ≡ ! 1 A Q a q ü È ´ ▒ ┴ ╤ β ± " # $ 2 3 4 B C D R S T b c d r s t é â Â Ê ô Ë ô ú ¨ ▓ │ ┤ ┬ ├ ─ ╥ ╙ ╘ Γ π ∑ ≧ ≦ ⌠ % 5 E U e u à Ï ゝ ╡ ┼ ╒ σ ⌡ & ' ( 6 7 8 F G H V W X f g h v w x ¶ ç ê û ù ¤ ³ Î ╢ ╖ ╕ ╞ ╟ ╚ ╓ ╫ ╪ μ τ Φ ÷ ) * + 9 : ; I J K Y Z [ i j k y z { ë è Ï Ô Ü ¢ ⌐ ¬ ½ ╣ ║ ╗ ╔ ╩ ╦ ┘ ┌ █ θ Ω δ , . / < = > ? L M N O ¥ ] ^ _ l m n o | } ~ € Î = À § £ Ù ¼ ¾ « » ╝ ╜ ╛ ┐ ╠ ═ ╬ ╧ ▃ ▌ ▐ ▄ ∞ ∈ ∩ - 82 - Û ƒ ≈ ｡ · √ ⁿ ² ￭ PMU2300ⅢSeries Product Specification 11.1.6 Codepage 00H to 7FH & PC865 (Nordic) 0 0 1 NU L DL E XO N 1 2 3 4 5 XOF F EO T EN Q 6 7 8 DC 4 CA N 9 A B HT C D E F FF FS CR GS LF ES C RS 2 3 0 4 @ 5 P 6 ` 7 p 8 Ç 9 É A á B ░ C └ D ╨ E α F ≡ ! 1 A Q a q ü æ í ▒ ┴ ╤ β ± " # $ 2 3 4 B C D R S T b c d r s t é â ä Æ ô ö ó ú ñ ▓ │ ┤ ┬ ├ ─ ╥ ╙ ╘ Γ π ∑ ≧ ≦ ⌠ % 5 E U e u à ò Ñ ╡ ┼ ╒ σ ⌡ & ' ( 6 7 8 F G H V W X f g h v w x å ç ê û ù ÿ a o ¿ ╢ ╖ ╕ ╞ ╟ ╚ ╓ ╫ ╪ μ τ Φ ÷ ) * + 9 : ; I J K Y Z [ i j k y z { ë è Ï Ö Ü ø ⌐ ¬ ½ ╣ ║ ╗ ╔ ╩ ╦ ┘ ┌ █ θ Ω δ , . / < = > ? L M N O ¥ ] ^ _ l m n o | } ~ € Î Ì Ä Å £ Ø ¼ ¡ « ¤ ╝ ╜ ╛ ┐ ╠ ═ ╬ ╧ ▃ ▌ ▐ ▄ ∞ ∈ ∩ - 83 - Pt ƒ ≈ ｡ · √ ⁿ ₂ ￭ PMU2300ⅢSeries Product Specification 11.1.7 Codepage 00H to 7FH & PC852 (Eastern Europe) 0 0 1 NU L DL E XO N 1 2 3 4 5 XOF F EO T EN Q 6 7 8 DC 4 CA N 9 A B HT C D E F FF FS CR GS LF ES C RS 2 3 0 4 @ 5 P 6 ` 7 p 8 Ç 9 É A á B ░ C └ D đ E ó F - ! 1 A Q a q ü Ĺ í ▒ ┴ Đ β ” " # $ 2 3 4 B C D R S T b c d r s t é â ä í ú ö ó ú Ą ▓ │ ┤ ┬ ├ ─ Ď Ë ď Ó Ń ń 、 ˇ ˘ % 5 E U e u ů Ľ ą Á ┼ Ň ň § & ' ( 6 7 8 F G H V W X f g h v w x ć ç ł Ĭ Ś ś Ž ž Ę Â Ě Ş Ă ă ╚ Í î ĕ Š š Ŕ ÷ ) * + 9 : ; I J K Y Z [ i j k y z { ë Ő ő Ö Ü Ť ę ť ź ╣ ║ ╗ ╔ ╩ ╦ ┘ ┌ █ Ú ŕ Ű ¨ · ű , . / < = > ? L M N O ¥ ] ^ _ l m n o | } ~ € î Ź Ä Ć Ł × č Č ş « » ╝ Ż ż ┐ ╠ ═ ╬ ¤ ▃ Ţ Ů ▀ ý Ý ţ ´ Ř ř ￭ SP - 84 - ゝﾟ PMU2300ⅢSeries Product Specification 11.1.8 Codepage 00H to 7FH & PC866 (Russian) 0 0 1 NU L DL E XO N 1 2 3 4 5 XOF F EO T EN Q 6 7 8 DC 4 CA N 9 A B HT C D E F FF FS CR GS LF ES C RS 2 3 0 4 @ 5 P 6 ` 7 p 8 Α 9 Р A а B ░ C └ D ╨ E р F Ë ! 1 A Q a q Б С б ▒ ┴ ╤ с ë " # $ 2 3 4 B C D R S T b c d r s t В Г Д Т У Ф в г д ▓ │ ┤ ┬ ├ ─ ╥ ╙ ╘ т у ф Є є Ї % 5 E U e u Е Х е ╡ ┼ ╒ ц ї & ' ( 6 7 8 F G H V W X f g h v w x Ж З И Ц Ч Ш ж з и ╢ ╖ ╕ ╞ ╟ ╚ ╓ ╫ ╪ ц ч х ў ﾟ ) * + 9 : ; I J K Y Z [ i j k y z { Й К Л Щ Ъ Ы й к л ╣ ║ ╗ ╔ ╩ ╦ ┘ ┌ █ ш щ ъ ･ · ű , . / < = > ? L M N O ¥ ] ^ _ l m n o | } ~ € М Н О П Ь Э Ю Я м н о п ╝ ╜ ╛ ┐ ╠ ═ ╬ ╧ ▃ Ţ Ů ▀ ы э ю я No． - 85 - ¤ ￭ PMU2300ⅢSeries Product Specification 11.1.9 Codepage 00H to 7FH & PC857 (Turkish) 0 0 1 NU L DL E XO N 1 2 3 4 5 XOF F EO T EN Q 6 7 8 DC 4 CA N 9 A B HT C D E F FF FS CR GS LF ES C RS 2 3 0 4 @ 5 P 6 ` 7 p 8 Ç 9 É A á B ░ C └ D o E ó F ― ! 1 A Q a q ü æ í ▒ ┴ a β ± " # $ 2 3 4 B C D R S T b c d r s t é â à Æ ô ö ó ú ñ ▓ │ ┤ ┬ ├ ─ Ê Ë È ô ò õ ¾ ¶ % 5 E U e u ä ò Ñ Á ┼ Õ § & ' ( 6 7 8 F G H V W X f g h v w x å ç ê û ù Í Ĝ ĝ ¿ Â À © ã Ã ╚ Í Î Ï μ ÷ × ﾟ ) * + 9 : ; I J K Y Z [ i j k y z { ë è ï Ö Ü ø ® ¬ ½ ╣ ║ ╗ ╔ ╩ ╦ ┘ ┌ █ Ú Û Ù ¨ . ¹ , . / < = > ? L M N O ¥ ] ^ _ l m n o | } ~ € î £ Ø Ş ş ¼ ¡ « » ╝ ¢ ¥ ┐ ╠ ═ ╬ ¤ ▃ ¦ Ì ▀ Ì ÿ ´ ³ ² ￭ SP - 86 - I Ä Å ゝ PMU2300ⅢSeries Product Specification 11.1.10 Codepage 00H to 7FH & PC864 (Arabic) - 87 - PMU2300ⅢSeries Product Specification 11.1.11 Codepage 00H to 7FH & WPC1252 0 0 1 NU L DL E XO N 1 2 3 4 5 XOF F EO T EN Q 6 7 8 DC 4 CA N 9 A B HT C D E F FF ES C FS CR GS LF RS 2 3 0 4 @ 5 P 6 ` 7 p 9 A B ° C À D Ð E à F ð ! 1 A Q a q ‘ ¡ ± Á Ñ á ñ " # $ 2 3 4 B C D R S T b c d r s t ’ “ ” ¢ £ ¤ ² ³ ´ Â Ã Ä Ò Ó Ô â ã ä ò ó Ô % 5 E U e u ‧ ¥ µ Å Õ å Õ & ' ( 6 7 8 F G H V W X f g h v w x † ‡ ˆ ‐ ~ ¦ § ¨ ¶ · ¸ Æ Ç È Ö × Ø æ ç è ö ÷ ) * + 9 : ; I J K Y Z [ i j k y z { ‰ ™ Š š ‹ › © ª « ¹ º » É Ê Ë Ù Ú Û é ê ë ù ú û , . / < = > ? L M N O ¥ ] ^ _ l m n o | } ~ € Œ œ Ž ž Ÿ ¬ ® ¯ ¼ ½ ¾ ¿ Ì Í Î Ï Ü Ý Þ ß ì í î ï ü ý þ ÿ - 88 - 8 € ¸ ƒ ,, ... ø PMU2300ⅢSeries Product Specification 11.1.12 Codepage 00H to 7FH & Thaicode18 - 89 - PMU2300ⅢSeries Product Specification 11.2 International Characters Code 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Country name U.S.A. France Germany U.K. Denmark I Sweden Italy Spain I Japan Norway Denmark II Spain II Latin America Korea Croatia China 23 ＃＃＃ £ ＃＃＃ Pt ＃＃＃＃＃＃＃＃ 24 ＄＄＄＄＄ ¤ ＄＄＄ ¤ ＄＄＄＄＄￥ 40 5B 5C 5D 5E 60 7B 7C 7D 7E ] ^ ' { | } ~ ＠ [ ╲ à ° ç § ^ ' é ù È ¨ § Ä Ö Ü ^ ' ä ö ü β ] ^ ' { | } ~ ＠ [ ╲ ' æ ø å ~ ＠ Æ Ø Å ^ É Ä Ö Å Ü é ä ö å ü é ^ ù à ò è ì ＠ ° ╲ ^ ' ¨ ñ } ~ ＠ ¡ Ñ ¿ ^ ' { | } ~ ＠ [ ￥ ] É Æ Ø Å Ü é æ ø å ü É Æ Ø Å Ü é æ ø å ü á ¡ Ñ ¿ é ' ì ñ ó ú á ¡ Ñ ¿ é ü ì ñ ó ú ^ ' { | } ~ ＠ [ ₩ ] Ž Š Đ Ć Č ž š đ ć č ] ^ ' { | } ~ ＠ [ ╲ - 90 - PMU2300ⅢSeries Product Specification 11.3 Kanji Code Chart 11.3.1 JIS Non-Kanji Shift JIS JIS 813F 814F 815F 816F 8180 8190 819E 81AE 81BE 81CE 81DE 81EE 823F 824F 825F 826F 8280 8290 829E 82AE 82BE 82CE 82DE 82EE 833F 834F 835F 836F 8380 8390 839E 83AE 83BE 83CE 83DE 83EE 2120 2130 2140 2150 2160 2170 2220 2230 2240 2250 2260 2270 2320 2330 2340 2350 2360 2370 2420 2430 2440 2450 2460 2470 2520 2530 2540 2550 2560 2570 2620 2630 2640 2650 2660 2670 0 ＾＼｛ ÷ ＄ ∪ ∃ ∇ ０Ｐｐぐだばむゐグダバムヰ Π π 1 2 3 4 5 6 7 8 9 A B C D E F ￣～｝＝￠ ◆ 、＿ ∥ 〈 ≠ ￡ □ 。ヽ｜〉＜％ ■ ，ヾ … 《＞＃ △ ．ゝ ‥ 》 ≦ ＆ ▲ ・ゞ ‘ 「 ≧ ＊ ▽ ：〃 ’ 」 ∞ ＠ ▼ ；仝 “ 『 ∴ § ※ ？〆 ” 』 ♂ ☆ 〒！〇（【 ♀ ★ → ∈ ∧ ゛〇）】 ° ○ ← ∋ ∨ ゜ ― 〔＋ ′ ● ↑ ⊆ ￢ ∠ ´ ― 〕－ ″ ◎ ↓ ⊇ ⇒ ⊥ ｀ ‐ ［ ± ℃ ◇ 〓 ⊂ ⇔ ⌒ ¨ ／］ × ￥ ∩ ≡ １ＡＱａｑぁけちぱめゑァケチパメヱ Α Ρ α ρ ≒ Å ≪ ‰ ≫ ♯ √ ♭ ∽ ♪ ∝ † ∵ ‡ ∫ ¶ ２ＢＲｂｒあげぢひもをアゲヂヒモヲ Β Σ β σ ３ＣＳｃｓぃこっびゃんィコッビャン Γ Τ γ τ ４ＤＴｄｔいごつぴや５ＥＵｅｕぅさづふゅ６ＦＶｆｖうざてぶゆ７ＧＷｇｗぇしでぷょ８ＨＸｈｘえじとへよ９ＩＹｉｙぉすどべらＪＺｊｚおずなぺりイゴツピヤヴ Δ Υ δ υ ゥサヅフュヵ Ε Φ ε φ ウザテブユヶ Ζ Χ ζ χ ェシデプョエジトヘヨォスドベラ Η Ψ η ψ Θ Ω θ ω - 91 - ⊃ ∀ ∂ ∬ ◯ ＫＬＭＮＯｋｌｍｎｏかせにほるがぜぬぼれきそねぽろぎぞのまゎくたはみわオズナペリカセニホルガゼヌボレキソネポロギゾノマヮクタハミワ Ι Κ Λ Μ Ν Ξ Ο ι κ λ μ ν ξ ο PMU2300ⅢSeries Product Specification Shift JIS JIS 843F 844F 845F 846F 8480 8490 849E 84AE 84BE 84CE 84DE 84EE 2720 2730 2740 2750 2760 2770 2820 2830 2840 2850 2860 2870 0 О Ю о ю ┛ ╂ 1 2 3 4 5 6 7 8 9 A B C D E F А П Я а п я ─ ┗ Б Р В С Г Т Д У Е Ф Ё Х Ж Ц З Ч И Ш Й Щ К Ъ Л Ы М Ь Н Э б р в с г т д у е ф ё х ж ц з ч и ш й щ к ъ л ы м ь н э │ ┣ ┌ ┳ ┐ ┫ ┘ ┻ └ ╋ ├ ┠ ┬ ┯ ┤ ┨ ┴ ┷ ┼ ┿ ━ ┝ ┃ ┰ ┏ ┥ ┓ ┸ - 92 - PMU2300ⅢSeries Product Specification 11.3.2 JIS Level 1 Characters Shift JIS JIS 889E 88AE 88BE 88CE 88DE 88EE 893F 894F 895F 896F 8980 8990 899E 89AE 89BE 89CE 89DE 89EE 8A3F 8A4F 8A5F 8A6F 8A80 8A90 8A9E 8AAE 8ABE 8ACE 8ADE 8AEE 8B3F 8B4F 8B5F 8B6F 8B80 8B90 3020 3030 3040 3050 3060 3070 3120 3130 3140 3150 3160 3170 3220 3230 3240 3250 3260 3270 3320 3330 3340 3350 3360 3370 3420 3430 3440 3450 3460 3470 3520 3530 3540 3550 3560 3570 0 旭粟夷萎稲碓雲頴園艶屋伽火迦介外垣覚橿叶完汗莞巌基軌祇黍朽巨 1 2 3 4 5 6 7 8 9 A B C D E F 亜葦袷委衣茨院臼荏英堰苑押憶価珂過会魁咳柿角梶椛粥官漢観玩奇機輝義却求拒唖芦安威謂芋陰渦餌衛奄薗旺臆佳禍霞解晦害蛎赫鰍樺刈寛澗諌癌嬉帰飢蟻客汲拠娃鯵庵尉違鰯隠嘘叡詠宴遠横桶加禾蚊回械崖鈎較潟鞄苅干潅貫眼寄毅騎誼脚泣挙阿梓按惟遺允韻唄営鋭延鉛欧牡可稼俄塊海慨劃郭割株瓦幹環還岩岐気鬼議虐灸渠哀圧暗意医印吋欝嬰液怨鴛殴乙嘉箇峨壊灰概嚇閣喝兜乾患甘鑑翫希汽亀掬逆球虚愛斡案慰井咽右蔚影疫掩塩王俺夏花我廻界涯各隔恰竃侃感監間贋幾畿偽菊丘究許挨扱闇易亥員宇鰻映益援於翁卸嫁苛牙快皆碍廓革括蒲冠慣看閑雁忌祈儀鞠久窮距姶宛鞍椅域因烏姥曳駅沿汚襖恩家茄画怪絵蓋拡学活釜寒憾竿関頑揮季妓吉仇笈鋸逢姐杏為育姻羽厩栄悦演甥鴬温寡荷臥悔芥街撹岳渇鎌刊換管陥顔机稀宜吃休級漁葵虻以畏郁引迂浦永謁炎凹鴎穏科華芽恢蟹該格楽滑噛勘敢簡韓願旗紀戯喫及糾禦茜飴伊異磯飲雨瓜泳越焔央黄音暇菓蛾懐開鎧核額葛鴨勧柑緩館企既徽技桔吸給魚穐絢位移一淫卯閏洩閲煙奥岡下果蝦賀戒階骸殻顎褐栢巻桓缶舘伎期規擬橘宮旧亨悪綾依維壱胤鵜噂瑛榎燕往沖化架課雅拐貝浬獲掛轄茅喚棺翰丸危棋記欺詰弓牛享握鮎偉緯溢蔭窺云盈厭猿応荻仮歌嘩餓改凱馨確笠且萱堪款肝含喜棄貴犠砧急去京渥或囲胃逸 - 93 - 丑運穎円縁億何河貨駕劾蛙穫樫鰹姦歓艦岸器起疑杵救居 PMU2300ⅢSeries Product Specification Shift JIS JIS 8B9E 8BAE 8BBE 8BCE 8BDE 8BEE 8C3F 8C4F 8C5F 8C6F 8C80 8C90 C89E 8CAE 8CBE 8CCE 8CDE 8CEE 8D3F 8D4F 8D5F 8D6F 8D80 8D90 8D9E 8DAE 8DBE 8DCE 8DDE 8DEE 8E3F 8E4F 8E5F 8E6F 8E80 8E90 3620 3630 3640 3650 3660 3670 3720 3730 3740 3750 3760 3770 3820 3830 3840 3850 3860 3870 3920 3930 3940 3950 3960 3970 3A20 3A30 3A40 3A50 3A60 3A70 3B20 3B30 3B40 3B50 3B60 3B70 0 彊鏡勤謹駒薫契経劇倹鍵言湖伍乞弘浩腔項告紺裟歳材咋三酸姉死諮 1 2 3 4 5 6 7 8 9 A B C D E F 供怯響均近具掘訓形継戟倦検険諺狐午鯉后恒港膏香国此艮坐済罪搾察傘餐姿氏資侠恐饗巾金愚窟群径繋撃健権顕限糊呉交喉慌溝航高穀頃魂座災財昨拶参斬子獅賜僑恭驚錦吟虞沓軍恵罫激兼牽験乎袴吾佼坑抗甲荒鴻酷今些挫采冴朔撮山暫屍祉雌兇挟仰斤銀喰靴郡慶茎隙券犬鹸個股娯侯垢拘皇行剛鵠困佐債犀坂柵擦惨残市私飼競教凝欣九空轡卦慧荊桁剣献元古胡後候好控硬衡劫黒坤叉催砕阪窄札撒仕師糸歯共橋尭欽倶偶窪袈憩蛍傑喧研原呼菰御倖孔攻稿講号獄墾唆再砦堺策殺散仔志紙事凶況暁琴句寓熊祁掲計欠圏硯厳固虎悟光孝昂糠貢合漉婚嵯最祭榊索薩桟伺思紫似協狂業禁区遇隈係携詣決堅絹幻姑誇梧公宏晃紅購壕腰恨左哉斎肴錯雑燦使指肢侍匡狭局禽狗隅粂傾敬警潔嫌県弦孤跨檎功工更紘郊拷甑懇差塞細咲桜皐珊刺支脂児卿矯曲筋玖串栗刑景軽穴建肩減己鈷瑚効巧杭絞酵濠忽昏査妻崎崎鮭鯖産司孜至字叫胸極緊矩櫛繰兄桂頚結憲見源庫雇碁勾巷校綱鉱豪惚昆沙宰裁埼笹捌算史斯視寺喬脅玉芹苦釧桑啓渓鶏血懸謙玄弧顧語厚幸梗耕砿轟骨根瑳彩載碕匙錆纂嗣施詞慈境興桐菌躯屑鍬圭畦芸訣拳賢現戸鼓誤口広構考鋼麹狛梱砂才際鷺冊鮫蚕四旨詩持峡蕎粁衿駆屈勲珪稽迎月捲軒絃故五護向庚江肯閤克込混詐採剤作刷皿讃士枝試時強郷僅襟駈 - 94 - 君型系鯨件遣舷枯互醐康洪肱降刻痕鎖栽在削晒賛始止誌 PMU2300ⅢSeries Product Specification Shift JIS JIS 8E9E 8EAE 8EBE 8ECE 8EDE 8EEE 8F3F 8F4F 8F5F 8F6F 8F80 8F90 8F9E 8FAE 8FBE 8FCE 8FDE 8FEE 903F 904F 905F 906F 9080 9090 909E 90AE 90BE 90CE 90DE 90EE 913F 914F 915F 916F 9180 9190 3C20 3C30 3C40 3C50 3C60 3C70 3D20 3D30 3D40 3D50 3D60 3D70 3E20 3E30 3E40 3E50 3E60 3E70 3F20 3F30 3F40 3F50 3F60 3F70 4020 4030 4040 4050 4060 4070 4120 4130 4140 4150 4160 4170 0 式疾斜酌腫衆柔出準署尚樟笑鉦情唇神塵逗瑞整誓石窃扇前狙双操草 1 2 3 4 5 6 7 8 9 A B C D E F 次識質煮釈趣宗襲汁術潤書勝庄樵粧鍾擾拭娠秦壬吹髄澄星請積節撰繊善疏叢早荘滋鴫実社錫酒就讐渋述盾薯匠床沼紹鐘条植寝紳尋垂崇摺晴逝籍説栓羨漸疎倉曹葬治竺蔀紗若首州蹴獣俊純藷升廠消肖障杖殖審臣甚帥嵩寸棲醒績雪栴腺然礎喪巣蒼爾軸篠者寂儒修輯縦峻巡諸召彰渉菖鞘浄燭心芯尽推数世栖青脊絶泉舛全祖壮槍藻璽宍偲謝弱受愁週重春遵助哨承湘蒋上状織慎薪腎水枢瀬正静責舌浅船禅租奏槽装痔雫柴車惹呪拾酋銃瞬醇叙商抄焼蕉丈畳職振親訊炊趨畝清斉赤蝉洗薦繕粗爽漕走磁七芝遮主寿洲酬叔竣順女唱招焦衝丞穣色新診迅睡雛是牲税跡仙染詮膳素宋燥送示叱屡蛇取授秀集夙舜処序嘗掌照裳乗蒸触晋身陣粋据凄生脆蹟先潜賎糎組層争遭而執蕊邪守樹秋醜宿駿初徐奨捷症訟冗譲食森辛靭翠杉制盛隻碩千煎践噌蘇匝痩鎗耳失縞借手綬終什淑准所恕妾昇省証剰醸蝕榛進笥衰椙勢精席切占煽選塑訴惣相霜自嫉舎勺朱需繍住祝循暑鋤娼昌硝詔城錠辱浸針諏遂菅姓聖惜拙宣旋遷岨阻想窓騒蒔室写尺殊囚習充縮旬曙除宵昭礁詳場嘱尻深震須酔頗征声戚接専穿銭措遡捜糟像辞悉射杓狩収臭十粛楯渚傷将晶祥象壌埴伸申人酢錐雀性製斥摂尖箭銑曾鼠掃総増汐湿捨灼珠周舟従塾殉庶償小松称賞嬢飾信疹仁図錘裾成西昔折川線閃曽僧挿綜憎鹿漆赦爵種 - 95 - 蒐戎熟淳緒少梢章醤常侵真刃厨随政誠析設戦鮮楚創掻聡 PMU2300ⅢSeries Product Specification Shift JIS JIS 919E 91AE 91BE 91CE 91DE 91EE 923F 924F 925F 926F 9280 9290 929E 92AE 92BE 92CE 92DE 92EE 933F 934F 935F 936F 9380 9390 939E 93AE 93BE 93CE 93DE 93EE 943F 944F 945F 946F 9480 9490 4220 4230 4240 4250 4260 4270 4320 4330 4340 4350 4360 4370 4420 4430 4440 4450 4460 4470 4520 4530 4540 4550 4560 4570 4620 4630 4640 4650 4660 4670 4720 4730 4740 4750 4760 4770 0 属太対退宅丹胆弛逐註聴沈槻釣悌徹点登凍盗動得鳶奈軟念農俳楳柏 1 2 3 4 5 6 7 8 9 A B C D E F 臓賊汰耐逮托叩単蛋恥秩酎帖脹珍佃鶴抵邸撤伝菟刀淘董同徳苫那難如捻覗廃煤泊蔵族詑岱隊択但嘆誕智窒鋳帳腸賃漬亭挺鄭轍殿賭唐湯蕩堂涜寅内汝尿撚蚤拝狽白贈続唾帯黛拓達坦鍛池茶駐庁蝶鎮柘低提釘迭澱途塔涛藤導特酉乍二韮燃巴排買箔造卒堕待鯛沢辰担団痴嫡樗弔調陳辻停梯鼎鉄田都塘灯討憧督瀞凪尼任粘把敗売粕促袖妥怠代濯奪探壇稚着瀦張諜津蔦偵汀泥典電鍍套燈謄撞禿噸薙弐妊乃播杯賠舶側其惰態台琢脱旦弾置中猪彫超墜綴剃碇摘填兎砥宕当豆洞篤屯謎迩忍廼覇盃陪薄則揃打戴大託巽歎断致仲苧徴跳椎鍔貞禎擢天吐砺島痘踏瞳毒惇灘匂認之杷牌這迫即存柁替第鐸竪淡暖蜘宙著懲銚槌椿呈程敵展堵努嶋祷逃童独敦捺賑濡埜波背蝿曝息孫舵泰醍濁辿湛檀遅忠貯挑長追潰堤締滴店塗度悼等透胴読沌鍋肉禰嚢派肺秤漠捉尊楕滞題諾棚炭段馳抽丁暢頂鎚坪定艇的添妬土投答鐙萄栃豚楢虹祢悩琶輩矧爆束損陀胎鷹茸谷短男築昼兆朝鳥痛壷帝訂笛纏屠奴搭筒陶道橡遁馴廿寧濃破配萩縛測村駄腿滝凧狸端談畜柱凋潮勅通嬬底諦適甜徒怒東糖頭銅凸頓縄日葱納婆倍伯莫足遜騨苔瀧蛸鱈箪値竹注喋牒捗塚紬庭蹄鏑貼斗倒桃統騰峠突呑畷乳猫能罵培剥駁速他体袋卓只樽綻知筑虫寵町直栂爪廷逓溺転杜党梼到闘鴇椴曇南入熱脳芭媒博麦俗多堆貸啄 - 96 - 誰耽地蓄衷眺朕掴吊弟哲顛渡冬棟働匿届鈍楠年膿馬梅拍 PMU2300ⅢSeries Product Specification Shift JIS JIS 949E 94AE 94BE 94CE 94DE 94EE 953F 954F 955F 956F 9580 9590 959E 95AE 95BE 95CE 95DE 95EE 963F 964F 965F 966F 9680 9690 969E 96AE 96BE 96CE 96DE 96EE 973F 974F 975F 976F 9780 9790 4820 4830 4840 4850 4860 4870 4920 4930 4940 4950 4960 4970 4A20 4A30 4A40 4A50 4A60 4A70 4B20 4B30 4B40 4B50 4B60 4B70 4C20 4C30 4C40 4C50 4C60 4C70 4D20 4D30 4D40 4D50 4D60 4D70 0 醗叛釆彼誹桧廟賓斧武憤弊偏圃俸飽棒撲摩鱒粍明茂尤矢涌誉熔沃乱 1 2 3 4 5 6 7 8 9 A B C D E F 函髪帆煩悲費鼻姫描頻普舞福扮柄変捕包法鳳冒朴磨桝漫民盟妄戻厄諭猶輿用浴卵箱伐搬頒扉避柊媛病敏浮葡腹焚並片歩呆泡鵬紡牧魔亦蔓眠迷孟籾役輸猷預窯翌嵐硲罰斑飯批非稗紐秒瓶父蕪複奮蔽篇甫報烹乏肪睦麻俣味務銘毛貰約唯由傭羊翼欄箸抜板挽披飛匹百苗不符部覆粉閉編補奉砲亡膨穆埋又未夢鳴猛問薬佑祐幼耀淀濫肇筏氾晩斐樋疋謬錨付腐封淵糞陛辺輔宝縫傍謀釦妹抹魅無姪盲悶訳優裕妖葉羅藍筈閥汎番比簸髭俵鋲埠膚楓弗紛米返穂峰胞剖貌勃昧末巳牟牝網紋躍勇誘容蓉螺蘭櫨鳩版盤泌備彦彪蒜夫芙風払雰頁遍募峯芳坊貿没枚沫箕矛滅耗門靖友遊庸要裸覧幡噺犯磐疲尾膝標蛭婦譜葺沸文僻便墓崩萌妨鉾殆毎迄岬霧免蒙匁柳宥邑揚謡来利肌塙班蕃皮微菱氷鰭富負蕗仏聞壁勉慕庖蓬帽防堀哩侭密鵡棉儲也薮幽郵揺踊莱吏畑蛤畔蛮碑枇肘漂品冨賦伏物丙癖娩戊抱蜂忘吠幌槙繭蜜椋綿木冶鑓悠雄擁遥頼履畠隼繁匪秘毘弼瓢彬布赴副鮒併碧弁暮捧褒忙頬奔幕麿湊婿緬黙夜愉憂融曜陽雷李八伴般卑緋琵必票斌府阜復分兵別鞭母放訪房北本膜万蓑娘面目爺愈揖夕楊養洛梨鉢判藩否罷眉畢表浜怖附幅吻塀瞥保簿方豊暴僕翻枕慢稔冥麺杢耶油有予様慾絡理溌半販妃肥美筆評瀕扶侮服噴幣蔑舗菩朋邦望卜凡鮪満脈名摸勿野癒柚余洋抑落璃発反範庇被 - 97 - 逼豹貧敷撫墳平箆鋪倣鋒某墨盆柾妙命模餅弥湧与溶欲酪 PMU2300ⅢSeries Product Specification Shift JIS JIS 979E 97AE 97BE 97CE 97DE 97EE 983F 984F 985F 986F 9880 9890 4E20 4E30 4E40 4E50 4E60 4E70 4F20 4F30 4F40 4F50 4F60 4F70 0 琉寮緑類齢楼論椀 1 2 3 4 5 6 7 8 9 A B C D E F 痢留料倫令暦蓮榔倭湾裏硫梁厘伶歴連浪和碗裡粒涼林例列錬漏話腕里隆猟淋冷劣呂牢歪離竜療燐励烈魯狼賄陸龍瞭琳嶺裂櫓篭脇律侶稜臨怜廉炉老惑率慮糧輪玲恋賂聾枠立旅良隣礼憐路蝋鷲葎虜諒鱗苓漣露郎亙掠了遼麟鈴煉労六亘略亮量瑠隷簾婁麓鰐劉僚陵塁零練廊禄詫流両領涙霊聯弄肋藁溜凌力累麗 - 98 - 朗録蕨 PMU2300ⅢSeries Product Specification 11.3.3 JIS Level 2 Characters Shift JIS JIS 989E 98AE 98BE 98CE 98DE 98EE 993F 994F 995F 996F 9980 9990 999E 99AE 99BE 99CE 99DE 99EE 9A3F 9A4F 9A5F 9A6F 9A80 9A90 9A9E 9AAE 9ABE 9ACE 9ADE 9AEE 9B3F 9B4F 9B5F 9B6F 9B80 9B90 5020 5030 5040 5050 5060 5070 5120 5130 5140 5150 5160 5170 5220 5230 5240 5250 5260 5270 5320 5330 5340 5350 5360 5370 5420 5430 5440 5450 5460 5470 5520 5530 5540 5550 5560 5570 0 舒仞佩俥偃儖兩冩凰剞勸卆厥呀咒唹喟嗤噫嚼坩埓墅壜夭娑媽孃它寳 1 2 3 4 5 6 7 8 9 A B C D E F 弌弍仭佰倚假僉儕兪冪凵剔辧勹卅厮听呻咫啀啻嗔噤囁圈埀堊墹壤夲奸娜嫣孅宦尅丐于仟侑倨會僊儔兮冫凾剪劬匆丗厰吭咀哂啣啾嘔嘯囃國垈埖墟壟夸妁娉嫗孀宸將丕亞价佯倔偕傳儚冀决刄剴劭匈卉厶吼呶咤啌喘嗷噬囀圍坡埣墫壯夾妝娚嫦孑寃專个亟伉來倪偐僂儡冂冱刋剩劼甸卍參吮咄咾售喞嘖噪囈圓坿堋墺壺竒佞婀嫩孕寇對丱亠佚侖倥偈僖儺囘冲刔剳劵匍凖簒吶咐咼啜單嗾嚆囎團垉堙壞壹奕侫婬嫖孚寉尓丶亢估儘倅做僞儷册冰刎剿勁匐卞雙吩咆哘啅啼嗽嚀囑圖垓堝墻壻奐妣婉嫺孛寔尠丼亰佛俔伜偖僥儼冉况刧剽勍匏卩叟吝哇哥啖喃嘛嚊囓嗇垠塲墸壼奎妲娵嫻孥寐尢丿亳佝俟俶偬僭儻冏冽刪劍勗匕卮曼呎咢哦啗喩嗹嚠囗圜垳堡墮壽奚姆娶嬌孩寤尨乂亶佗俎倡偸僣儿冑凅刮劔勞匚夘燮咏咸唏唸喇噎嚔囮圦垤塢壅夂奘姨婢嬋孰實尸乖从佇俘倩傀僮兀冓凉刳劒勣匣卻叮呵咥唔唳喨噐嚏囹圷垪塋壓夊奢姜婪嬖孳寢尹乘仍佶俛倬傚價兒冕凛刹剱勦匯卷叨咎咬哽啝嗚營嚥圀圸垰塰壑夐奠妍媚嬲孵寞屁亂仄侈俑俾傅僵兌冖几剏劈飭匱厂叭呟哄哮喙嗅嘴嚮囿坎埃毀壗夛奧姙媼嫐學寥屆亅仆侏俚俯傴儉兔冤處剄劑勠匳厖叺呱哈哭喀嗟嘶嚶圄圻埆塒壙梦奬姚媾嬪斈寫屎豫仂侘俐們傲儁兢冦凩剋辨勳匸厠吁呷咨哺咯嗄嘲嚴圉址埔堽壘夥奩娥嫋嬶孺寰屓亊仗佻俤倆 - 99 - 儂竸冢凭剌勵區厦吽呰哢喊嗜嘸囂坏埒塹壥夬娟嫂嬾宀寶 PMU2300ⅢSeries Product Specification Shift JIS JIS 9B9E 9BAE 9BBE 9BCE 9BDE 9BEE 9C3F 9C4F 9C5F 9C6F 9C80 9C90 9C9E 9CAE 9CBE 9CCE 9CDE 9CEE 9D3F 9D4F 9D5F 9D6F 9D80 9D90 9D9E 9DAE 9DBE 9DCE 9DDE 9DEE 9E3F 9E4F 9E5F 9E6F 9E80 9E90 5620 5630 5640 5650 5660 5670 5720 5730 5740 5750 5760 5770 5820 5830 5840 5850 5860 5870 5920 5930 5940 5950 5960 5970 5A20 5A30 5A40 5A50 5A60 5A70 5B20 5B30 5B40 5B50 5B60 5B70 0 岼崟嶄巫幟廾彑徙怙恊悵慇慚憊懣抂拈捐捩攝攬收斟昃晟朧枩柞梳梵 1 2 3 4 5 6 7 8 9 A B C D E F 屐岷崛嶂已幢廖弃彖徘怐恆悄惘愾慫憑懶戞抉拜挾掾搗據擶攸斫旻晢曄霸杼柝栫梠屏峅崑嶢巵幤廣弉彗徠怩恍悛慍愨慴憫懺戡找拌捍揩搨擒擴畋斷杳晰暸朮杪柢桙梺孱岾崔嶝帋幇廝彝彙徨怎恣悖愕愧慯憮懴截抒拊搜揀搏擅擲效旃昵暃曖朿枌柮档椏屬峇崢嶬帚幵廚彜彡徭怱恃悗愆慊慥懌懿戮抓拂捏揆摧擇擺敖旆昶暈曚朶枋枹桷梍屮峙崚嶮帙并廛弋彭徼怛恤悒惶愿慱懊懽戰抖拇掖揣摯撻攀敕旁昴暎曠杁枦柎桾桾乢峩崙嶽帑幺廢弑彳忖怕恂悧惷愼慟應懼戲拔抛掎揉摶擘擽敍旄昜暉昿朸枡柆梟椁屶峽崘嶐帛麼廡弖彷忻怫恬悋愀愬慝懷懾戳抃拉掀插摎擂攘敘旌晏暄曦朷枅柧梏棊屹峺嵌嶷帶广廨弩徃忤怦恫惡惴愴慓懈戀扁抔挌掫揶攪擱攜敞旒晄暘曩杆枷檜梭椈岌峭嵒嶼帷庠廩弭徂忸怏恙悸惺愽慵懃戈扎拗拮捶揄撕擧攅敝旛晉暝曰杞柯栞梔棘岑嶌嵎巉幄廁廬弸彿忱怺悁惠愃慂憙懆戉扞拑拱掣搖撓舉攤敲旙晁曁曵杠枴框條椢岔峪嵋巍幃廂廱彁徊忝恚悍惓愡慄憖憺戍扣抻挧掏搴撥擠攣數无晞暹曷杙柬栩梛椦妛崋嵬巓幀廈廳彈很悳恁惧悴惻慳憇懋戌扛拏挂掉搆撩擡攫斂旡晝曉朏杣枳桀梃棡岫崕嵳巒幎廐廰彌徑忿恪悃忰惱慷憬罹戔扠拿挈掟搓撈抬攴斃旱晤暾朖杤柩桍檮椌岻崗嵶巖幗廏廴彎徇怡恷悚悽愍慘憔懍戛扨拆拯掵搦撼擣攵變杲晧暼朞枉枸栲梹棍岶嵜嶇巛幔 - 100 - 廸弯從恠恟惆愎慙憚懦扼擔拵捫搶擯攷斛昊晨朦杰柤桎桴 PMU2300ⅢSeries Product Specification Shift JIS JIS 9E9E 9EAE 9EBE 9ECE 9EDE 9EEE 9F3F 9F4F 9F5F 9F6F 9F80 9F90 9F9E 9FAE 9FBE 9FCE 9FDE 9FEE E03F E04F E05F E06F E080 E090 E09E E0AE E0BE E0CE E0DE E0EE E13F E14F E15F E16F E180 E190 5C20 5C30 5C40 5C50 5C60 5C70 5D20 5D30 5D40 5D50 5D60 5D70 5E20 5E30 5E40 5E50 5E60 5E70 5F20 5F30 5F40 5F50 5F60 5F70 6020 6030 6040 6050 6060 6070 6120 6130 6140 6150 6160 6170 0 椣楡榻槲樶欅歙殪麾汾洌淦湮滿溥澎濱瀰烙熕牋狎猥玻瑁甍畧痂痼瘰 1 2 3 4 5 6 7 8 9 A B C D E F 棔椡楞槃槧橸檗蘖歔殫氈汨沺浣涸渮渝滂漾澑濮瀾焉熨燹牘狒猾珀瑜瓠甕畫疳瘁瘻棧棆楝榧樅橇蘗櫺歛殯氓汳泛涓淆渙游溟漓濂濛瀲烽熬燿牴狢獎珥瑩瓣畭畭痃痰癇棕楹榁樮榱橢檻欒歟殲气沒泯浤淬湲溂潁滷潦瀉灑焜燗爍牾狠獏珮瑰瓧甞畸疵痺癈椶楷楪榑樞橙櫃欖歡殱氛沐泙浚淞湟溪漑澆澳瀋灣焙熹爐犂狡默珞瑣瓩甦當疽痲癆椒楜榲榠槭橦櫂鬱歸殳氤泄泪浹淌渾溘灌潺澣濺炙煥熾爛犁狹獗璢瑪瓮甬疆疸痳癜椄楸榮榜樔橈檸欟歹殷氣泱洟浙淨渣滉滬潸澡瀑炒煕燒爨犇狷獪琅瑶瓲甼疇疼瘋癘棗楫槐榕槫樸檳欸歿殼汞泓衍涎淒湫溷滸澁澤瀁炯熈燉爭犒倏獨瑯瑾瓰畄畴疱瘍癡棣楔榿榴樊樢檬欷殀毆汕沽洶涕淅渫滓滾澀澹瀏烱煦燔爬犖猗獰琥璋瓱畍疊痍瘉癢椥楾槁槞樒檐櫞盜殄毋汢泗洫濤淺湶溽漿潯濆濾炬煢燎爰犢猊獸珸璞瓸畊疉痊瘟癨棹楮槓槨櫁檍櫑欹殃毓汪泅洽涅淙湍溯滲潛澪瀛炸煌燠爲犧猜獵琲璧瓷畉疂痒瘧癩棠椹榾樂樣檠櫟飮殍毟沂泝洸淹淤渟滄漱濳濟瀚炳煖燬爻犹猖獻琺瓊甄畛疔痙瘠癪棯楴槎樛樓檄檪歇殘毬沍沮洙渕淕湃溲滯潭濕潴炮煬燧爼犲猝獺瑕瓏甃畆疚痣瘡癧椨椽寨槿橄檢櫚歃殕毫沚沱洵渊淪渺滔漲澂濬瀝烟熏燵爿狃猴珈琿瓔甅畚疝痞瘢癬椪楙槊權樌檣櫪歉殞毳沁沾洳涵淮湎滕滌潼濔瀘烋燻燼牀狆猯玳瑟珱甌畩疥痾瘤癰椚椰槝槹橲 - 101 - 櫻歐殤毯沛洒淇渭渤溏潘濘瀟烝熄牆狄猩珎瑙甎畤疣痿瘴 PMU2300ⅢSeries Product Specification Shift JIS JIS E19E E1AE E1BE E1CE E1DE E1EE E23F E24F E25F E26F E280 E290 E29E E2AE E2BE E2CE E2DE E2EE E33F E34F E35F E36F E380 E390 E39E E3AE E3BE E3CE E3DE E3EE E43F E44F E45F E46F E480 E490 6220 6230 6240 6250 6260 6270 6320 6330 6340 6350 6360 6370 6420 6430 6440 6450 6460 6470 6520 6530 6540 6550 6560 6570 6620 6630 6640 6650 6660 6670 6720 6730 6740 6750 6760 6770 0 皸眄睾矗碚祕秬穉窶竦箘篝簧籥粽絨綫縊縲辮羂羸耒聳胛膂臉與艢苣 1 2 3 4 5 6 7 8 9 A B C D E F 癲皹眩睹矚碌磧祓秡穡竅竭筺箟篩簪籬糀紂絮總縣縺繿罅羆譱耘聲胥隋膠臍舊艨苟癶皺眤瞎矜碣磚祺秣穢竄竰笄箍簑簟籵糅紜絏綢縡繧纈罌羃翅耙聰胙腆膕臑舍艪苒癸盂眞瞋矣碵磽祿稈穩窿笂筍箜簔簷粃糂紕絣綯縒繝纉罍羈翆耜聶胝脾膤臙舐艫苴發盍眥瞑矮碪磴禊稍龝邃笏笋箚篦簫粐糘紊經緜縱繖續罎羇翊耡聹胄腓膣臘舖舮苳皀盖眦瞠矼碯礇禝稘穰竇笊筌箋篥簽粤糒絅綉綸縟繞纒罐羌翕耨聽胚腑腟臈舩艱苺皃盒眛瞞砌磑礒禧稙穹竊笆筅箒籠籌粭糜絋絛綟縉繙纐网羔翔耿聿胖胼膓臚舫艷莓皈盞眷瞰砒磆礑齋稠穽竍笳筵箏簀籃粢糢紮綏綰縋繚纓罕羞翡耻肄脉腱膩臟舸艸范皋盡眸瞶礦磋礙禪稟窈竏笘筥筝簇籔粫鬻紲絽緘縢繹纔罔羝翦聊肆胯腮膰臠舳艾苻皎盥睇瞹砠磔礬禮禀窗竕笙筴箙簓籏粡糯紿綛緝繆繪纖罘羚翩聆肅胱腥膵臧艀芍苹皖盧睚瞿礪碾礫禳稱窕竓笞筧篋篳籀粨糲紵綺緤繦繩纎罟羣翳聒肛脛腦膾臺艙芒苞皓盪睨瞼硅碼祀禹稻窘站笵筰篁篷籐粳糴絆綮緞縻繼纛罠羯翹聘肓脩腴膸臻艘芫茆皙蘯睫瞽碎磅祠禺稾窖竚笨筱篌簗籘粲糶絳綣緻縵繻纜罨羲飜聚肚脣膃膽臾艝芟苜皚盻睛瞻硴磊祗秉稷窩竝笶筬篏簍籟粱糺絖綵緲縹纃缸罩羹耆聟肭脯膈臀舁艚芻茉皰眈睥矇碆磬祟秕穃竈竡筐筮箴篶籤粮紆絎緇緡繃緕缺罧羮耄聢冐腋膊臂舂艟芬苙皴眇睿矍硼 - 102 - 祚秧穗窰竢箝篆簣籖粹絲綽縅縷繽罸羶耋聨肬膀膺舅艤苡 PMU2300ⅢSeries Product Specification Shift JIS JIS E49E E4AE E4BE E4CE E4DE E4EE E53F E54F E55F E56F E580 E590 E59E E5AE E5BE E5CE E5DE E5EE E63F E64F E65F E66F E680 E690 E69E E6AE E6BE E6CE E6DE E6EE E73F E74F E75F E76F E780 E790 6820 6830 6840 6850 6860 6870 6920 6930 6940 6950 6960 6970 6A20 6A30 6A40 6A50 6A60 6A70 6B20 6B30 6B40 6B50 6B60 6B70 6C20 6C30 6C40 6C50 6C60 6C70 6D20 6D30 6D40 6D50 6D60 6D70 0 莪萓萸葯蒡薜蘋蚩蛟蜷螳蠕衾袱褓覦訐誂諤謳谿貔賽赭跟躇軅輟轢逅 1 2 3 4 5 6 7 8 9 A B C D E F 茵莟菫蔆葹蔡蕁蕷藾蚪蛛蜻蝓蟇蠢袞裃襃襦覬訌誄諱鞫譟豈豼賺赱跣蹇躅軈輛轣迹茴莢菎菻萵蓿蘂蕾藺蚋蛯蜥蝣蟆蠡衵裄褞襤覯訛誨謔謦譬豌貘賻赳跼蹉躄軋輌轤迺茖莖菽葭蓊蓴蕋薐蘆蚌蜒蜩蝪螻蠱衽裔褥襭覲訝誡諠謫譯豎戝贄趁踈蹌躋軛輦辜逑茲茣萃萪葢蔗蕕藉蘢蚶蜆蜚蠅蟯蠶袵裘褪襪覺訥誑諢謾譴豐貭贅趙踉蹐躊軣輳辟逕茱莎菘萼蒹蔘薀薺蘚蚯蜈蝠螢蟲蠹衲裙褫襯覽訶誥諷謨譽豕貪贊跂跿蹈躓軼輻辣逡荀莇萋蕚蒿蔬薤藏蘰蛄蜀蝟螟蟠蠧袂裝襁襴覿詁誦諞譁讀豢貽贇趾踝蹙躑軻輹辭逍茹莊菁蒄蒟蔟薈薹蘿蛆蜃蝸螂蠏蠻袗裹襄襷觀詛誚諛譌讌豬貲贏趺踞蹤躔軫轅辯逞荐荼菷葷蓙蔕薑藐虍蚰蛻蝌螯蠍衄袒褂褻襾觚詒誣謌譏讎豸貳贍跏踐蹠躙軾轂辷逖荅莵萇葫蓍蔔薊藕乕蛉蜑蝎蟋蟾衂袮裼褶覃觜詆諄謇譎讒豺貮贐跚踟踪躪輊輾迚逋茯荳菠蒭蒻蓼薨藝虔蠣蜉蝴螽蟶衒袙裴褸覈觝詈諍謚證讓貂貶齎跖蹂蹣躡輅轌迥逧茫荵菲葮蓚蕀蕭藥號蚫蜍蝗蟀蟷衙袢裨襌覊觧詼諂諡譖讖貉賈贓跌踵蹕躬輕轉迢逶茗莠萍蒂蓐蕣薔藜虧蛔蛹蝨蟐蠎衞袍裲褝覓觴詭諚謖譛讙貅賁賍跛踰蹶躰輒轆迪逵茘莉萢葩蓁蕘薛藹虱蛞蜊蝮雖蟒衢袤褄襠覘觸詬諫謐譚讚貊賤贔跋踴蹲軆輙轎迯逹莅莨萠葆蓆蕈藪蘊蚓蛩蜴蝙螫蠑衫袰褌襞覡訃詢諳謗譫谺貍賣贖跪蹊蹼躱輓轗邇迸莚菴莽萬蓖 - 103 - 薇蘓蚣蛬蜿蟄蠖袁袿褊覩訖誅諧謠豁貎賚赧跫躁躾輜轜迴 PMU2300ⅢSeries Product Specification Shift JIS JIS E79E E7AE E7BE E7CE E7DE E7EE E83F E84F E85F E86F E880 E890 E89E E8AE E8BE E8CE E8DE E8EE E93F E94F E95F E96F E980 E990 E99E E9AE E9BE E9CE E9DE E9EE EA3F EA4F EA5F EA6F EA80 EA90 6E20 6E30 6E40 6E50 6E60 6E70 6F20 6F30 6F40 6F50 6F60 6F70 7020 7030 7040 7050 7060 7070 7220 7230 7240 7250 7260 7270 7220 7230 7240 7250 7260 7270 7320 7330 7340 7350 7360 7370 0 邂鄒醫釵鉋鎔鐇鑰閠關隶霎靜鞐韶餔饑駮騾髏魄鮴鯰鰰鴃鶲鸚麸黴齔 1 2 3 4 5 6 7 8 9 A B C D E F 遏遽鄙醯釶鉐錙鎹鐐鑵閨闡陝隸霑靠鞜韵顱餘饒駱驕髑髻魃鯀鰕鱇鴆鵝鷄鸛麪黶齣遐邁鄲醪鈞銜錢鏖鐶鑷閧闥陟隹霏靤鞨頏顴餡饌駲驍髓鬆魏鯊鰔鰲鴪鵞鷁鸞麭黷齟遑邀鄰醵釿銖錚鏗鐫鑽閭闢陦雎霖靦鞦頌顳餝饕駻驛體鬘魍鮹鰉鱆鴦鵤鶻鹵靡黹齠遒邊酊醴鈔銓錣鏨鐵鑚閼阡陲雋霙靨鞣頸颪餞馗駸驗髞鬚魎鯆鰓鰾鶯鵑鶸鹹黌黻齡逎邉酖醺鈬銛錺鏥鐡鑼閻阨陬雉霤勒鞳頤颯餤馘騁驟髟鬟魑鯏鰌鱚鴣鵐鶺鹽黎黼齦遉邏酘釀鈕鉚錵鏘鐺鑾閹阮隍雍霪靫鞴頡颱餠馥騏驢髢鬢魘鯑鰆鱠鴟鵙鷆麁黏黽齧逾邨酣釁鈑鋏錻鏃鑁钁閾阯隘襍霰靱韃頷颶餬馭騅驥髣鬣魴鯒鰈鱧鵄鵲鷏麈黐鼇齬遖邯酥釉鉞銹鍜鏝鑒鑿闊陂隕雜霹靹韆頽飄餮馮駢驤髦鬥鮓鯣鰒鱶鴕鶉鷂麋黔鼈齪遘邱酩釋鉗銷鍠鏐鑄閂濶陌隗霍霽鞅韈顆飃餽馼騙驩髯鬧鮃鯢鰊鱸鴒鶇鷙麌黜皷齷遞邵酳釐鉅鋩鍼鏈鑛閇闃陏險雕霾靼韋顏飆餾駟騫驫髫鬨鮑鯤鰄鳧鵁鶫鷓麒點鼕齲遨郢酲釖鉉錏鍮鏤鑠閊闍陋隧雹靄鞁韜顋飩饂駛騷驪髮鬩鮖鯔鰮鳬鴿鵯鷸麕黝鼡齶遯郤醋釟鉤鋺鍖鐚鑢閔闌陷隱霄靆靺韭顫飫饉駝驅骭髴鬪鮗鯡鰛鳰鴾鵺鷦麑黠鼬龕遶扈醉釡鉈鍄鎰鐔鑞閖闕陜隲霆靈鞆齏顯餃饅駘驂骰髱鬮鮟鰺鰥鴉鵆鶚鷭麝黥鼾龜隨郛醂釛銕錮鎬鐓鑪閘闔陞隰霈靂鞋韲顰餉饐駑驀骼髷鬯鮠鯲鰤鴈鵈鶤鷯麥黨齊龠遲鄂醢釼鈿 - 104 - 鎭鐃鈩閙闖隴霓靉鞏竟餒饋駭驃髀鬲鮨鯱鰡鳫鶩鷽麩黯齒 PMU2300ⅢSeries Product Specification Shift JIS JIS EA9E EAAE EABE EACE EADE EAEE 7420 7430 7440 7450 7460 7470 0 1 2 3 4 堯槇遙瑤 5 6 - 105 - 7 8 9 A B C D E F

Operační Manuál

Rating

Date

Size

Views

Categories

Share

Transcript

Forgot your password?.