Operating Instructions Sony Mhc-grx9900

Transcript

You can read the recommendations in the user guide, the technical guide or the installation guide for SONY MHC-GRX9900. You'll find the answers to all your questions on the SONY MHC-GRX9900 in the user manual (information, specifications, safety advice, size, accessories, etc.). Detailed instructions for use are in the User's Guide. User manual SONY MHC-GRX9900 User guide SONY MHC-GRX9900 Operating instructions SONY MHC-GRX9900 Instructions for use SONY MHC-GRX9900 Instruction manual SONY MHC-GRX9900 You're reading an excerpt. Click here to read official SONY MHCGRX9900 user guide http://yourpdfguides.com/dref/1103237 Manual abstract: @@Model No. _______________ Serial No. @@Refer servicing to qualified personnel only. @@These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. @@@@@@@@This stereo system is equipped with the Dolby Btype noise reduction system*. * Manufactured under license from Dolby Laboratories Licensing Corporation. DOLBY and the double-D symbol a are trademarks of Dolby Laboratories Licensing Corporation. CAUTION The use of optical instruments with this product will increase eye hazard. 2 Table of Contents Getting Started Step 1: Hooking up the system ... ..... .... 5 Step 2: Setting the time ...... .......... ..... .... 7 Step 3: Presetting radio stations . ......... 8 Saving the power in standby mode . .. 10 Sound Adjustment Adjusting the sound ........ ..... ..... .......... 28 Selecting the audio emphasis .......... ... 29 Changing the spectrum analyzer display .. ..... .......... .......... ..... ..... ........ 31 Selecting surround effects .. .......... ..... .. 31 Adjusting the graphic equalizer ... ...... 32 Making a personal audio emphasis file .... .......... ..... ..... .......... .......... ..... ..... .... 33 Basic Operations Playing a CD ...... .......... ..... ..... .......... ..... 11 Recording a CD ..... ..... ..... .......... .......... . 13 Listening to the radio .... ..... .......... ........ 14 Recording from the radio .. ..... ..... ........ 15 Playing a tape .. .......... ..... ..... .......... ........ 16 Recording from a tape .. ..... ..... .......... ... 18 Other Features Using the Radio Data System (RDS)* 34 Singing along: Karaoke ....... ..... ..... ..... 36 Falling asleep to music ..... .......... ..... .... 38 Waking up to music . .......... .......... ..... ... 39 Timer-recording radio programs .. ..... 40 The CD Player Using the CD display ..... .......... ..... ..... .. 19 Playing the CD tracks repeatedly ...... 20 Playing the CD tracks in random order .. .......... ..... ..... .......... .......... ..... 21 Programming the CD tracks ..... .......... 22 Playing CDs without interruption ..... 23 Optional AV components Connecting audio components ..... ..... 41 Connecting a VCR ..... .......... .......... ..... .. 43 Connecting the surround speakers ... . 43 Connecting outdoor antennas ......... ... 44 The Tape Deck Recording on a tape manually ....... .... 24 Recording a CD by specifying track order . ..... .......... .......... ..... ..... .......... .. 25 Additional Information Precautions ........ ..... ..... .......... .......... ..... . 45 Troubleshooting .... .......... .......... ..... ..... . 46 Specifications ......... .......... ..... ..... .......... . 49 Parts identification ......... ..... ..... .......... .. 54 Index ........ ..... ..... .......... .......... .. Back cover * European model only DJ Effects Looping part of a CD ... ..... .......... ......... 27 Flashing part of a CD . ..... ..... .......... ...... 27 3 Using this manual The instructions in this manual are for MHC-GRX9900/GRX70/GRX70J/GRX50/R770/RXD9/ RXD80/RXD7. The MHC-RXD80 is the model used for illustration purposes. Otherwise, the model name is indicated in the illustrations. The shape of the buttons on the MHC-GRX9900/ RXD9 is different from that of the MHC-GRX70, but the locations of the buttons are the same. Any differences in operation are clearly indicated in the text, for example, "MHC-GRX70 only" or "Europearn model only". MHCGRX70/GRX70J/GRX50/R770/ RXD80/RXD7 MHC-GRX9900/RXD9 * * This part of the MHC-GRX50/R770/RXD7 is different from other models as below: MHC-GRX50/R770/RXD7 EDIT DIRECTION REPEAT TUNER MEMORY STEREO/MONO MHC-GRX70/GRX70J/RXD80 MHC-GRX9900/RXD9 FILE GEQ P FILE EFFECT SELECT CONTROL MEMORY PLAY MODE DOLBY NR PTY** FILE SELECT EDIT PLAY MODE REPEAT DIRECTION DOLBY NR STEREO/MONO TUNER MEMORY PTY** ** "PTY" is for European model only. 4 Getting Started Step 1: Hooking up the system Do the following procedure 1 to 4 to hook up your system using the supplied cords and accessories. AM loop antenna FM antenna 2 3 1 4 Front speaker (Right) Front speaker (Left) 1 Connect the speakers. Connect the speaker cords of front speakers to the SPEAKER jacks as below. For the front speakers with jacks, connect the speaker cords to the speakers in the same way. Insert only the stripped portion. R Notes · Keep the speaker cords away from the antennas to prevent noise. · The type of speakers supplied vary according to the model you purchased (see "Specifications" on page 52). continued + L + Red/ Solid (`) Black/ Stripe (') 5 Step 1: Hooking up the system (continued) 3 For models with a voltage selector, set VOLTAGE SELECTOR to position of your local power line voltage. VOLTAGE SELECTOR 2 Connect the FM/AM antennas. Set up the AM loop antenna, then connect it. Jack type A AM loop antenna Extend the FM lead antenna horizontally. 230 - 240V FM 75 AM 4 Connect the power cord to a wall outlet. The demonstration appears in the display. When you press , the system turns on and the demonstration automatically ends. If the supplied adapter on the plug does not fit your wall outlet, detach it from the plug (only for models equipped with an adapter). Jack type B Extend the FM lead antenna horizontally. AM loop antenna FM CO 75 AX IAL To connect optional AV components See page 41. AM To deactivate the demonstration When you set the time (Step 2: Setting the time), the demonstration is deactivated. To activate/deactivate the demonstration again, press DISPLAY (MHC-RXD9/RXD80/ RXD7/R770) or DEMO (STANDBY) (MHCGRX9900/GRX70/GRX70J/GRX50) while the system is off. 6 22 0V 12 0V To attach the front speaker pads Attach the supplied front speaker pads to the bottom of the speakers to stabilize the speakers and prevent them from slipping. Step 2: Setting the time You must set the time before using the timer functions. The clock is on a 24-hour system for the European model, and a 12-hour system for other models. The 24-hour system model is used for illustration purposes. DISPLAY 2,4 3,5 Inserting two size AA (R6) batteries into the remote ] } ] } Tip With normal use, the batteries should last for about six months. When the remote no longer operates the system, replace both batteries with new ones. Note If you do not use the remote for a long period of time, remove the batteries to avoid possible damage from battery leakage. 1 1 Press CLOCK/TIMER SET. The hour indication flashes. When carrying this system Do the following to protect the CD mechanism. 1 @@2 Hold down LOOP and press "LOCK" appears in the display. so that 2 Turn the jog dial to set the hour. continued 7 Step 2: Setting the time (coninued) 3 Press ENTER/NEXT. The minute indication flashes. Step 3: Presetting radio stations You can preset the following number of stations: 2 band model: 20 for FM, 10 for AM. 3 band model: 20 for FM, 10 for MW, and 10 for SW, or 20 for FM, 10 for AM and 5 for UKV, depending on the model you purchased. (Power) Jog dial 4 5 Tip Turn the jog dial to set the minute. Press ENTER/NEXT. The clock starts working. 4 1 If you've made a mistake, start over from step 1. You're reading an excerpt. Click here to read official SONY MHCGRX9900 user guide http://yourpdfguides.com/dref/1103237 To change the time The previous explanation shows you how to set the time while the power is off. To change the time while the power is on, do the following: 1 2 3 4 Press CLOCK/TIMER SET. Turn the jog dial to select SET CLOCK. Press ENTER/NEXT. Perform steps 2 through 5 above. Note The clock settings are canceled when you disconnect the power cord or if a power failure occurs. 3 2 8 1 Press TUNER/BAND repeatedly until the band you want appears in the display. The bands you can receive vary depending on the model you purchased. Be sure to check which bands you can receive. Every time you press this button, the band changes as follows: 2 band model: FM ~ AM 3 band model: FM n MW n SW n or FM n AM n UKV* * "STEREO PLUS" is displayed when you select UKV. n To tune in a station with a weak signal Press + or repeatedly in step 2 to tune in the station manually. To set another station to the exist preset number Start over from step 1. After step 3, turn the jog dial to select the preset number you want to store the other station. You can add a new preset number after the last preset number. To erase a preset station 1 Keep pressing TUNER MEMORY until a preset number appears in the display. 2 Press and hold + or until the frequency indication starts to change, then release. Scanning stops when the system tunes in a station. "TUNED" and "STEREO" (for a stereo program) appear. 2 Turn the jog dial to select the preset number you want to erase. Select "ALL ERASE" when you want to erase all the preset stations. 3 Press ENTER/NEXT. "COMPLETE" appears. When you erase a preset number, the preset number decreases by one and all preset numbers following the erased one are renumbered. To change the AM tuning interval 3 Press TUNER MEMORY. A preset number appears in the display. The stations are stored from preset number 1. Preset number (Except for the European and Middle Eastern models) The AM tuning interval is factory set to 9 kHz (10 kHz in some areas). To change the AM tuning interval, tune in any AM station first, then turn off the power. While holding down the ENTER/NEXT button, turn the power back on. When you change the interval, AM preset stations will be erased. To reset the interval, repeat the same procedure. Tip The preset stations are retained for half a day even if you unplug the power cord or if a power failure occurs. 4 5 Press ENTER/NEXT. The station is stored. Repeat steps 1 to 4 to store other stations. 9 Saving the power in standby mode (For MHC-RXD9/RXD80/RXD7/R770) You can lower the power consumption to a minimum (Power Saving Mode) and save energy in the standby mode. POWER SAVE /DEMO (Power) Tips · Each time you press POWER SAVE/DEMO in the Power Saving Mode, the display switches between the Power Saving Mode and the demo mode. · indicator and timer indicator (when the timer is set) t to record from the reverse side, press TAPE B 9 to light its indicator after pressing CD SYNC. · When you record on both sides, be sure to start from the front side. If you start from the reverse side, recording stops at the end of the reverse side. · When you want to reduce the hiss noise in lowlevel high-frequency signals, press DOLBY NR so that "DOLBY NR" appears after pressing CD SYNC. Press § and insert a recordable tape into deck B. Note You cannot listen to other sources while recording. 13 Listening to the radio Preset Tuning Preset radio stations in the tuner's memory first (see "Step 3: Presetting radio stations"). (Power) 1 Press TUNERis off automatically turns the power on and starts tape playback if there is a tape in the deck (One Touch Play). When the system is in the Power Saving Mode, the One Touch Play function does not work. · You can switch from another source to the tape deck just by pressing TAPE A (or TAPE B) ( or 9 (Automatic Source Selection). · When you want to reduce the hiss noise in lowlevel high-frequency signals, press DOLBY NR so that "DOLBY NR" appears. 2 Press DIRECTION repeatedly to select A to play one side. Select ß* to play both sides. To play both decks in succession, select RELAY (relay play).** Searching for the beginning of a track (AMS*) During playback, turn the jog dial the same direction as the 9 or ( indicator to go forward. Turn the opposite direction to go back. (Or press = or + on the remote. ) The search direction, + (forward) or (back), and number of songs being skipped (1~9) appear in the display. Example: searching forward 2 songs 3 Press TAPE A (or TAPE B) ( (DECK A (or DECK B) ( on the remote). Press TAPE A (or TAPE B) 9 to play the reverse side. (Press DECK A (or DECK B) ( again on the remote to play the reverse side.) The tape starts playing. Basic Operations * The deck stops automatically after repeating the sequence five times. ** Relay play always follows the following sequence: Deck A (front side), Deck A (reverse side), Deck B (front side), Deck B (reverse side). To Stop play Fast-forward Rewind Adjust the volume Do this Press p. Press 0 or ). Press 0 or ). Turn VOLUME (or press VOL +/ on the remote). * AMS (Automatic Music Sensor) Notes The AMS function may not operate correctly under the following circumstances: When the unrecorded space between songs is less than 4 seconds long. If completely different information is recorded on the left and right channels. When there are continuous sections of extremely low level or low frequency sound (like those of a baritone sax). When the unit is placed near a television. (In this case, we recommend moving the unit farther away from the television or turning off the television.) Remove the cassette Press §. 17 Recording from a tape -- High-speed Dubbing You can use TYPE I (normal) or TYPE II (CrO2) tapes. The recording level is automatically adjusted. (Power) DOLBY NR 3 Press DIRECTION repeatedly to select A to record on one side. Select ß (or RELAY) to record on both sides. Press REC PAUSE/START. Dubbing starts. 4 2 To stop dubbing Press p. Tips · When you dub on both sides, start recording from the front side. If you record from the reverse side, recording stops at the end of the reverse side. · If you set DIRECTION to ß when the tapes you use have different lengths, the tape in each deck reverses independently. If you select RELAY, the tapes in both decks reverse together. · You don't have to set DOLBY NR, since the tape in deck B is automatically recorded in the same state as the tape in deck A. 1 1 3 p 4 1 Press § and insert a recorded tape in deck A and a recordable tape in deck B. With the side you want to play/record facing forward 2 Press HI-DUB. Deck B stands by for recording. 18 The CD Player Using the CD display You can check the remaining time of the current track or that of the CD. You're reading an excerpt. Click here to read official SONY MHCGRX9900 user guide http://yourpdfguides.com/dref/1103237 When a CD TEXT disc is loaded, you can check the information stored on the disc, such as the disc titles or artist names. When the unit detects CD TEXT discs, the "CD TEXT" indication appears in the display. (Power) / Press DISPLAY. Each time you press the button during normal playback or in the stop mode, the display changes as follows: During normal playback n Playing time on the current track µ Remaining time on the current track µ Remaining time on current CD (1 DISC mode) or "--.--" display (ALL DISCS mode) µ Title name of the current track* µ Clock display (for eight seconds) µ Effect (P FILE) name or "EFFECT ON (OFF)" In the stop mode n Title name of the CD* µ Artist information* µ Total number of tracks and total playing time µ Clock display (for eight seconds) µ Effect (P FILE) name or "EFFECT ON (OFF)" * With CD TEXT discs only (certain characters cannnot be displayed). When the disc contains more than 20 tracks, CD TEXT is not displayed from track 21 on. DISPLAY 19 Playing the CD tracks repeatedly Repeat Play This function lets you repeat a single CD or all CDs in normal play, Shuffle Play and Program Play. (Power) PLAY MODE To cancel Repeat Play Press REPEAT so that "REPEAT" or "REPEAT 1" disappears from the display. REPEAT / Press REPEAT during playback until "REPEAT" appears in the display. Repeat Play starts. Do the following procedure to change the repeat mode. To repeat All the tracks on the current CD All the tracks on all CDs Only one track Press PLAY MODE repeatedly until "1 DISC" appears in the display. PLAY MODE repeatedly until "ALL DISCS" appears in the display. REPEAT repeatedly until "REPEAT 1" appears in the display while playing the track you want to repeat. 20 Playing the CD tracks in random order Shuffle Play You can play all the tracks on one CD or all CDs in random order. (Power) DISC 1~3 To cancel Shuffle Play Press PLAY MODE repeatedly until "SHUFFLE" or "PROGRAM" disappears from the display. The tracks continue playing in their original order. To select a desired CD Press DISC 1~3. Tips · You can start Shuffle Play during normal play by pressing PLAY MODE repeatedly to select "SHUFFLE". · To skip a track, turn the jog dial clockwise (or press + on the remote). 3 1 1 2 2 Jog dial Press FUNCTION repeatedly until "CD" appears in the display, then place a CD. Press PLAY MODE repeatedly until "1 DISC SHUFFLE " or "ALL DISCS SHUFFLE" appears in the display. "ALL DISCS" shuffles all the CDs in the player. "1 DISC" shuffles the CD whose DISC indicator is green. 3 Press CD (P. All the tracks play in random order. 21 Programming the CD tracks Program Play You can make a program of up to 32 tracks from all the CDs in the order you want them to be played. (Power) 1 2 3 4 Press FUNCTION repeatedly until "CD" appears in the display, then place a CD. @@Press one of the DISC 1~3 buttons to select a CD. Turn the jog dial until the desired track appears in the display. Disc number Total playing time (including selected track) 3 7 Track number 5 Press ENTER/NEXT. The track is programmed. The program step number appears, followed by the total playing time. 1 2 p 45 6 To program additional tracks, repeat steps 3 to 5. Skip step 3 to select tracks from the same disc. Press CD (P. All the tracks play in the order you selected. CD ( p =+ CHECK CLEAR 7 VOL +/ 22 To cancel Program Play Press PLAY MODE repeatedly until "PROGRAM" or "SHUFFLE" disappears from the display. To Check the program Press CHECK on the remote repeatedly. After the last track, "CHECK END" appears. CLEAR on the remote in stop mode. CHECK on the remote repeatedly until the number of the track to be erased lights up, then press CLEAR. 1 Select the disc tray with a DISC 1~3 button. 2 Select the track by turning the jog dial. 3 Press ENTER/NEXT. p once in stop mode or twice while playing. Playing CDs without interruption Non-Stop Play You can play CDs without pausing between tracks. Clear a track from the end Clear a specific track (Power) 3 Add a track to the program Clear the entire program Tips · The program you made remains in the CD player even after it has been played back. Press CD (P to play the same program again. · If "--.--" appears instead of the total playing time during programming, this means: you have programmed a track number which exceeds 20. the total playing time has exceeded 100 minutes. 1 1 2 2 Press FUNCTION repeatedly until "CD" appears in the display, then place a CD. Press NON-STOP to light the indicator. "NON-STOP PLAY" appears in the display. 3 Press CD (P. To cancel Non-Stop Play Press NON-STOP so that the indicator goes out and "NON-STOP OFF" appears in the display. 23 The Tape Deck Recording on a tape manually You can record from CD, tape, or radio as you like. For example, you can record just the songs you want or record from the middle of the tape. The recording level is adjusted automatically. (Power) 4 Press DIRECTION repeatedly to select A to record on one side. Select ß (or RELAY) to record on both sides. Press REC PAUSE/START. Recording starts. 5 6 Start playing the source to be recorded. DOLBY NR To Stop recording Pause recording Press p. REC PAUSE/START. Tips · If you want to record from the reverse side, press TAPE B 9 to light its indicator after pressing REC PAUSE/START in step 3. · When you want to reduce the hiss noise in lowlevel high-frequency signals, press DOLBY NR so that "DOLBY NR" appears after pressing REC PAUSE/START in step 3. · When recording from a CD, you can use the jog dial to select tracks during rec pause mode (after pressing REC PAUSE/START in step 3 and before pressing again in step 5). 2 1 2 3 4 p 3,5 1 Insert a recordable tape into deck B. Press FUNCTION repeatedly until the source you want to record (e. g., CD) appears. Press REC PAUSE/START. Deck B stands by for recording. The indicator on TAPE B ( (for front side) lights up. 24 Recording a CD by specifying track order -- Program Edit You can record tracks from all the CDs in the order you want. When programming, make sure the playing times for each side do not exceed the length of one side of the tape. 1 2 3 4 5 Place a CD and insert a recordable tape into deck B. @@@@Press one of the DISC 1~3 buttons to select a CD. @@@@@@@@@@@@@@@@@@@@This lets you create original recordings. (Power) Flashing part of a CD -- Flash With the flash function, you can "flash" the CD sound during playback. You're reading an excerpt. Click here to read official SONY MHCGRX9900 user guide http://yourpdfguides.com/dref/1103237 This lets you create original recordings. (Power) LOOP Jog dial FLASH Jog dial / Press and hold LOOP during playback at the point you want to start the Loop function, and release to resume normal play. @@@@@@@@@@@@@@@@@@@@@@Press GROOVE again to return to the previous volume. @@@@@@@@@@@@@@@@@@@@@@The indicator turns off. The synchronized equalizer is canceled also when: -- -- -- -- -- cancel the effect select the effect from the music menu select the surround effect adjust the graphic equalizer sing along (karaoke). Notes · SYNC EQ does not work in KARAOKE mode. · For MHC-GRX9900/GRX70/GRX70J/RXD9/ RXD80, P FILE MEMORY does not work in SYNC EQ mode. · The names of classification are not related with the genre of the music source. 30 Changing the spectrum analyzer display You can enjoy changing the display while listening to the music. (Power) Selecting surround effects You can enjoy surround effects. (Power) SURROUND SPECTRUM ANALYZER / Press SURROUND repeatedly to select the surround effect you desire. Every time you press the button, the display changes as follows: SURROUND ON ( ) SURROUND OFF (off) ~ / Press SPECTRUM ANALYZER. Every time you press the button, the display changes as follows: IMAGE PATTERN NORMAL PATTERN ~ Tip For MHCGRX9900/GRX70/GRX70J/RXD9/ RXD80, if you want to memorize the effect, store it into a personal file (see "Making a personal audio emphasis file"). Note When you choose other sound effects, the surround effects will be canceled. 31 Adjusting the graphic equalizer (MHC-GRX9900/GRX70/GRX70J/RXD9/ RXD80 only) You can adjust the sound by raising or lowering the levels of specific frequency ranges. Before operation, first select the audio emphasis you want for your basic sound. 4 Turn the jog dial to adjust level. 5 6 Repeat steps 3 and 4. Press ENTER/NEXT when finished. (Power) 4 6 Note If you choose another menu audio emphasis (other than "EFFECT OFF"), the adjusted sound effect is lost. To retain the adjusted sound effect for future use, store it in a personal file. (See "Making a personal audio emphasis file".) 2 1 2 3 3 Select the audio emphasis you want for your basic sound (see "Selecting the audio emphasis" on page 29). Press GEQ CONTROL. Press + or repeatedly to select a frequency band. 32 Making a personal audio emphasis file -- Personal file (MHC-GRX9900/GRX70/GRX70J/RXD9/ RXD80 only) You can create a personal file of audio patterns (surround effect and graphic equalizer) and store them in the memory of the unit. Later, call up an audio pattern to play a favorite tape, CD, or radio program. Create up to five audio files. Before operation, first select the audio emphasis you want for your basic sound. (Power) 3 4 Use the jog dial to select the file number (P FILE 1~5) where you want to store the sound effect. Press ENTER/NEXT. The adjusted sound effects are stored under the selected file number. The settings previously stored at this memory location are erased and replaced by the new settings. To call up the personal file 1 Press FILE SELECT. 2 Use the jog dial to select the personal file you desire. 3 Press ENTER/NEXT. 23 4 FILE SELECT 1 2 Obtain the sound effect you want by using the graphic equalizer and surround effect. Press P FILE MEMORY. The personal file number appears in the display. 33 Other Features Using the Radio Data System (RDS) (For European model only) What is the Radio Data System? Radio Data System (RDS) is a broadcasting service that allows radio stations to send additional information along with the regular program signal. This tuner offers convenient RDS features like station name display and location of stations by program type. RDS is available only on FM stations.* Note RDS may not work properly if the station you are tuned to is not transmitting the RDS signal properly or if the signal strength is weak. * Not all FM stations provide RDS service, nor do they provide the same type of services. If you are not familiar with the RDS system, check with your local radio stations for details on RDS services in your area. To check the RDS information Each time you press DISPLAY, the display changes as follows: n Station name* µ Frequency µ Program type* µ Clock display µ Effect (P FILE) name or "EFFECT ON (OFF)" * If the RDS broadcast is not received, the station name and program type may not appear in the display. Locating a station by program type (PTY) You can locate a station you want by selecting a program type. The unit tunes in the type of programs currently being broadcast from the RDS stations stored in the tuner's preset memory. (Power) Receiving RDS broadcasts / Simply select a station from the FM band. When you tune in a station that provides RDS services, the station name appears in the display. 1 2,3,4,5 34 1 2 3 Press PTY while listening to the radio. Turn jog dial to select the program type you want. See the "List of program types" section below. @@@@@@POP Popular music programs. ROCK Rock music programs. EASY MUSIC Easy listening (middle of the road music). L. @@S. @@OTHER MUSIC Music, such as rhythm and blues and reggae. WEATHER Weather information. FINANCE Stock market reports and trading, etc. CHILDREN Programs for young. SOCIAL Programs about people and the things that affect them. RELIGION Programs of religious contents. @@TRAVEL Programs about travel. Not for announcements that are located TP/TA. @@@@AFFAIRS Topical programs that expand on current news. INFORMATION Programs about consumer affairs, medical advice. SPORT Sports programs. @@DRAMA Radio plays and serials. @@COUNTRY Country music programs. NATION Programs featuring the popular music of the country or region. OLDIES Programs featuring oldies music. FOLK Folk Music Programs. DOCUMENTARY Investigative features. ALARM TEST Test signal for emergency broadcasts. ALARM-ALARM Emergency broadcasts. @@You need to connect an optional microphone. (Power) 3 Notes "NO PTY" appears when the program type you selected is not currently being broadcast. 1,5 2 1 2 3 VOLUME Turn MIC LEVEL to 0 to turn down the microphone control level. Connect an optional microphone to MIX MIC. Press KARAOKE PON/MPX repeatedly to obtain the karaoke effect you desire. Every time you press the button, the display changes as follows: n KARAOKE PON n MPX R n MPX L EFFECT OFF (ON)* N * When an audio emphasis is selected, the effect name apears. 36 The h indicator appears in the display when a karaoke mode is activated. To sing karaoke with decreasing the vocal level of a CD, select "KARAOKE PON". To sing karaoke of multiplex CD or tape, select "MPX R" or "MPX L". 4 5 Start playing the music and adjust the volume. Adjust the microphone volume by turning MIC LEVEL. Mixing and recording sounds (Power) 4 When you are done Turn MIC LEVEL to 0 and disconnect the microphone from MIX MIC, then press KARAOKE PON/MPX repeatedly so that "h" disappears. You're reading an excerpt. Click here to read official SONY MHCGRX9900 user guide http://yourpdfguides.com/dref/1103237 Note With some songs, vocals may not be cancelled when you select "KARAOKE PON". Adjusting the microphone echo (For Middle Eastern models only) (Power) p 2,3 1 1 2 3 4 Do the procedures for singing along (steps 1 to 5 on page 36, 37). Then, insert a tape in deck B. Press REC PAUSE/START. Press REC PAUSE/START again. Recording starts. Press CD (P to start playing the CD player (or TAPE A ( for tape deck A). Playback starts. Start singing along with the music. ECHO LEVEL / Turn ECHO LEVEL to adjust the echo effect. To cancel the echoing Turn ECHO LEVEL to 0. continued 37 Singing along: Karaoke (continued) To stop recording Press p. Tips · If acoustic feedback (howling) occurs, move the microphone away from the speakers or change the direction of the microphone. · If you want to record your voice through the microphone only, you can do so by selecting the CD function and not playing a CD. · When high level sound signals are input, the unit automatially adjusts the recording level to prevent distortion of the recorded sound signal (Auto Level Control function). Falling asleep to music -- Sleep Timer You can let the system turn off at the preset time, so you can sleep to the music. You can preset the time to be turned off by 10 minutes. SLEEP Notes · If you press EFFECT (or ON/OFF on the remote) or recall a sound effect, the karaoke mode is cancelled. · The instrumental sound may be reduced as well as the singer's voice when the sound is recorded in monaural. · The singer's voice may not be reduced when: --only a few instruments are playing. --a duet is being played. --the source has strong echoes or chorus. --the singer's voice deviates from the center. --the voice on the source is singing in high soprano or tenor. / Press SLEEP. Every time you press the button, the minute display (the turn-off time) changes as follows: AUTO n 90min n 80min n 70min n ... n 10min n OFF n AUTO .. . When you choose "AUTO" The power turns off when the current CD or tape finishes playback (for up to 100 minutes). To check the remaining time Press SLEEP once. To change the time to turn off Select the time you want by pressing SLEEP. To cancel the Sleep Timer function Press SLEEP repeatedly until "SLEEP OFF" appears. 38 Waking up to music -- Wake-up Timer You can wake up to music at a preset time every day. Make sure you have set the clock (see "Step 2: Setting the time"). 4 Turn jog dial to select "DAILY 1 (or 2)", then press ENTER/NEXT. "ON" appears and the hour digits flash in the display. 9 TIMER SELECT 5 Set the time to start playback. Turn jog dial to set the hour, then press ENTER/NEXT. The minute indication starts flashing. Turn jog dial to set the minute, then press ENTER/NEXT. The hour indication flashes again. 6 7 Set the time to stop playback following the above procedure. Turn jog dial until the music source you want appears. The indications change as follows: n TUNER ~ CD PLAY N n TAPE PLAY N 3 4,5,6, 2 7,8 1 Prepare the music source you want to play. · CD: Insert a CD. To start from a specific track, make a program (see "Programming the CD tracks" on page 22). · Tape: Insert an tape with the side you want to play facing forward. · Radio: Tune in the preset station you want (see "Step 3: Presetting radio stations" on page 8). 8 Press ENTER/NEXT. The type of timer (DAILY 1 or DAILY 2), followed by the start time, stop time and the music source, appears, then the original display appears. 9 Turn off the power. 2 3 Adjust the volume. Press CLOCK/TIMER SET. "SET (DAILY 1)" appears. continued 39 Waking up to music (continued) To check the setting Press TIMER SELECT and turn the jog dial to select the respective mode (DAILY 1 or DAILY 2), then press ENTER/NEXT. To change the setting, start over from step 1. Timer-recording radio programs To timer-record, you must preset the radio station (see "Step 3: Presetting radio stations") and set the clock (see "Step 2: Setting the time") beforehand. To cancel the timer operation Press TIMER SELECT and turn the jog dial to select "TIMER OFF", then press ENTER/ NEXT. Tip The power turns on 15 seconds before the preset time. 7 TIMER SELECT 2 3,4,5 1 2 3 6 Tune in the preset radio station (see "Listening to the radio" on page 14). Press CLOCK/TIMER SET. "SET (DAILY 1)" appears. Turn jog dial to select "REC", then press ENTER/NEXT. "ON" appears and the hour digits flash in the display. 40 Optional AV components 4 Set the time to start recording. Turn the jog dial to set the hour, then press ENTER/NEXT. The minute indication starts flashing. Connecting audio components Select one of the following connections, depending on the equipment to be connected and method of connecting. Refer to the instructions of each component. Turn the jog dial to set the minute, then press ENTER/NEXT. The hour indication flashes again. 5 Connecting an MD deck for digital recording You can record from CD into the MD deck digitally by connecting an optical cable. To the DIGITAL IN jack of the MD deck Set the time to stop recording following the above procedure. The start time appears, followed by the stop time, the preset radio station to be recorded (e.g., "TUNER FM 5"), then the original display appears. 6 7 Insert a recordable tape. Turn off the power. When the recording starts, the volume level is set to the minimum. To check the setting Press TIMER SELECT and turn the jog dial to select "REC", then press ENTER/NEXT. To change the setting, start over from step 1. To cancel the timer operation Press TIMER SELECT and turn the jog dial to select "TIMER OFF", then press ENTER/ NEXT. Note If the power is on at the preset time, the recording will not be made. continued 41 Connecting audio components (continued) Connecting a super woofer speaker (except for MHC-RXD9 (European model)/RXD7 (European model)/ R770) You can connect an optional super woofer speaker. To super woofer Connecting an MD deck for analog recording Make sure to match the color of the plugs and the connectors. To listen to the sound of the connected MD deck, press FUNCTION repeatedly until "MD" appears. To the audio output of the MD deck To the audio input of the MD deck Tip When you connect a Sony MD deck, you can use the MD (, P, and p buttons on this unit's remote to perform play, pause, and stop operations. 42 Connecting a VCR Make sure to match the color of the plugs and the connectors. To listen to the sound of the connected VCR, press FUNCTION repeatedly until "VIDEO" appears. Refer to the instructions of each component. To the audio output of the VCR Connecting the surround speakers (MHCGRX70/GRX70J only) Connect the speaker cords from the surround speakers to the appropriate SURROUND SPEAKER jacks. You're reading an excerpt. Click here to read official SONY MHCGRX9900 user guide http://yourpdfguides.com/dref/1103237 Connect the solid cords to the red jacks and connect the striped cords to the black jacks. Keep the speaker cords away from the antennas to prevent noise. To surround speaker (R) To surround speaker (L) 43 Connecting outdoor antennas Connect the outdoor antenna to improve the reception. Refer to the instructions of each component. AM antenna Connect a 6- to 15- meter (20- to 50- feet) insulated wire to the AM antenna terminal. Leave the supplied AM loop antenna connected. Jack type A Insulated wire (not supplied) FM antenna Connect the optional FM outdoor antenna. You can also use the TV antenna instead. Jack type A AM FM 75 75-ohm coaxial cable (not supplied) Jack type B Insulated wire (not supplied) FM 75 FM CO75 AX IA AM L AM Jack type B IEC standard socket connector (not supplied) FM CO75 AX IA L AM 44 Additional Information Precautions On operating voltage Before operating the system, check that the operating voltage of your system is identical with the voltage of your local power supply. Notes on CDs · Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out. · Do not use solvents such as benzene, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs. · Do not expose the CD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight. On safety · The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. · Unplug the system from the wall outlet (mains) if it is not to be used for an extended period of time. To disconnect the cord (mains lead), pull it out by the plug. Never pull the cord itself. · Should any solid object or liquid fall into the component, unplug the stereo system and have the component checked by qualified personnel before operating it any further. · The AC power cord must be changed only at the qualified service shop. Cleaning the cabinet Use a soft cloth slightly moistened with mild detergent solution. To save a tape permanently To prevent a tape from being accidentally recorded over, break off the cassette tab from side A or B as illustrated. Detector slots On placement · Place the stereo system in a location with adequate ventilation to prevent heat build-up in the stereo system. · Do not place the unit in an inclined position. · Do not place the unit in locations where it is; -- Extremely hot or cold -- Dusty or dirty -Very humid -- Vibrating -- Subject to direct sunlight. Tab of side B Tab of side A Side A Break off the cassette tab of side A On operation · If the stereo system is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lens inside the CD player. Should this occur, the system will not operate properly. @@· When you move the system, take out any discs. If you have any questions or problems concerning your stereo system, please consult your nearest Sony dealer. If you later want to reuse the tape for recording, cover the broken tab with adhesive tape. However, be careful not to cover the detector slots which allow the tape player to automatically detect the type of tape. Tape type: CrO2/METAL NORMAL Detector slots continued 45 Precautions (continued) Before placing a cassette in the tape deck Take up any slack in the tape. Otherwise the tape may get entangled in the parts of the tape deck and become damaged. Troubleshooting If you run into any problem using this stereo system, use the following check list. First, check that the power cord is connected firmly and the speakers are connected correctly and firmly. Should any problem persist, consult your nearest Sony dealer. When using a tape longer than 90 minutes The tape is very elastic. Do not change the tape operations such as play, stop, and fast-winding etc. frequently. The tape may get entangled in the tape deck. General The display starts flashing as soon as you plug in the power cord even though you haven't turned on the power (demonstration mode). ·Press DISPLAY (MHCRXD9/RXD80/ RXD7/R770) or DEMO (STANDBY) (MHC-GRX9900/GRX70/GRX70J/ GRX50) when the power is turned off. The demonstration disappears. The demonstration mode appears automatically the first time you plug in the power cord or if there is a power outage lasting longer than half a day. The clock setting/radio presetting/timer is canceled. ·The power cord is disconnected or a power failure occurs longer than half a day. Redo the followings: -"Step 2: Setting the time" -- "Step 3: Presetting radio stations" If you have set the timer, also redo "Waking up to music" and "Timerrecording radio programs". There is no sound. ·Rotate VOLUME clockwise. ·The headphones are connected. ·Insert only the stripped portion of the speaker cord into the SPEAKER jack. Inserting the vinyl portion of the speaker cord will obstruct the speaker connections. ·There is no audio output during timer recording. Cleaning the tape heads Clean the tape heads after every 10 hours of use. When the tape heads become dirty; -- the sound is distorted -- there is a decrease in sound level -- the sound drops out -- the tape does not erase completely -- the tape does not record. Make sure to clean the tape heads before you start an important recording or after playing an old tape. Use separately sold dry-type or wet-type cleaning cassette. For details, refer to the instructions of the cleaning cassette. Demagnetizing the tape heads Demagnetize the tape heads and the metal parts that have contact with the tape every 20 to 30 hours of use with a separately sold demagnetizing cassette. For details, refer to the instructions of the demagnetizing cassette. 46 There is severe hum or noise. · A TV or VCR is placed too close to the stereo system. Move the stereo system away from the TV or VCR. "0:00" (or "12:00") flashes in the display. · A power interruption occurred. Set the clock and timer settings again. The timer does not function. · Set the clock correctly. DAILY 1, DAILY 2, and REC do not appear when you press the TIMER SELECT button. · Set the timer correctly. · Set the clock. The remote does not function. · There is an obstacle between the remote and the system. · The remote is not pointing in the direction of the system's sensor. · The batteries have run down. Replace the batteries. There is acoustic feedback. · Decrease the volume level. · Move the microphone away form the speakers or change the direction of the microphone. The color irregularity on a TV screen persists. · Turn off the TV set once, then turn it on after 15 to 30 minutes. If the color irregularity still persists, place the speakers farther away from the TV set. You're reading an excerpt. Click here to read official SONY MHCGRX9900 user guide http://yourpdfguides.com/dref/1103237 "PROTECT" and "PUSH POWER" appear alternately. · A strong signal was input. @@·Check the speaker connection and speaker placement. Sound lacks bass. @@·The CD is not placed properly. The CD will not play. ·The CD is not lying flat in the disc tray. ·The CD is dirty. ·The CD is inserted label side down. ·Moisture condensation has built up. @@Play does not start from the first track. ·The player is in program or shuffle mode. @@"OVER" is displayed. ·You have reached the end of the CD. Press and hold 0 to return. continued 47 Troubleshooting (continued) Tuner Severe hum or noise ("TUNED" or "STEREO" flashes in the display). ·Adjust the antenna. ·The signal strength is too weak. Connect the external antenna. A stereo FM program cannot be received in stereo. ·Press STEREO/MONO so that "STEREO" appears. Tape Deck The tape does not record. ·No tape in the cassette holder. ·The tab has been removed from the cassette (see "To save a tape permanently" on page 45). ·The tape has reeled to the end. The tape does not record nor play or there is a decrease in sound level. ·The heads are dirty. Clean them (see "Cleaning the tape heads" on page 46). ·The record/playback heads are magnetized. @@The tape does not erase completely. ·The record/playback heads are magnetized. @@There is excessive wow or flutter, or the sound drops out. ·The capstans or pinch rollers are dirty. Clean them (see "Cleaning the tape heads" on page 46). Noise increases or the high frequencies are erased. ·The record/playback heads are magnetized. @@@@· The cassette tape was not inserted correctly. @@2 Plug the power cord back in. 3 Press p, ENTER/NEXT, and at the same time. 4 Press to turn on the power. The system is reset to the factory settings. All the settings you made, such as the preset stations, clock, and timer are cleared. You should set them again. 48 Specifications AUDIO POWER SPECIFICATIONS: (MHC-RXD9 U.S. A. models only) POWER OUTPUT AND TOTAL HARMONIC DISTORTION: with 8 ohm loads both channels driven, from 70-20,000 Hz; rates 140 watts per channel minimum RMS power, with no more than 0.9% total harmonic distortion from 250 milliwatts to rated output. Amplifier section Canadian models: MHC-RXD80: Continuous RMS power output (reference) 100 + 100 watts (8 ohms at 1 kHz, 10% THD) Total harmonic distortion less than 0.07% (8 ohms at 1 kHz, 55 W) MHC-RXD7: Continuous RMS power output (reference) 70 + 70 watts (6 ohms at 1 kHz, 10% THD) Total harmonic distortion less than 0.07% (6 ohms at 1 kHz, 45 W) European models: MHC-RXD9: DIN power output (rated) 120 + 120 watts (8 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 150 + 150 watts (8 ohms at 1 kHz, 10% THD) Music power output (reference) 275 + 275 watts (8 ohms at 1 kHz, 10% THD) MHC-R770/RXD7: DIN power output (rated) 80 + 80 watts (8 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 100 + 100 watts (8 ohms at 1 kHz, 10% THD) Music power output (reference) 170 + 170 watts (8 ohms at 1 kHz, 10% THD) Other models: MHC-GRX9900: The following measured at AC 120, 220, 240 V 50/60 Hz DIN power output (rated) 200 + 200 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 250 + 250 watts (6 ohms at 1 kHz, 10% THD) MHC-GRX70/GRX70J: The following measured at AC 120, 220, 240 V 50/60 Hz DIN power output (rated) 130 + 130 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 170 + 170 watts (6 ohms at 1 kHz, 10% THD) MHC-GRX50: The following measured at AC 120, 220, 240 V 50/60 Hz DIN power output (rated) 110 + 110 watts (8 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 140 + 140 watts (8 ohms at 1 kHz, 10% THD) continued 49 Specifications (continued) Inputs MD IN: (phono jacks) VIDEO (AUDIO) IN: (phono jacks) MIX MIC: (phone jack) Tape player section Recording system Frequency response (DOLBY NR OFF) 4-track 2-channel stereo 40 13,000 Hz (±3 dB), using Sony TYPE I cassette 40 14,000 Hz (±3 dB), using Sony TYPE II cassette ±0.15% W.Peak (IEC) 0.1% W.RMS (NAB) ±0. 2% W.Peak (DIN) voltage 450 mV, impedance 47 kilohms voltage 250 mV, impedance 47 kilohms sensitivity 1 mV, impedance 10 kilohms Wow and flutter Outputs MD OUT: voltage 250 mV (phono jacks) impedance 1 kilohms PHONES: accepts headphones of (stereo mini jack) 8 ohms or more SPEAKER: MHCGRX9900/GRX70/GRX70J/RXD7 (Canadian model): accepts impedance of 6 to 16 ohms MHC-RXD9/RXD7 (European model)/RXD80/ R770/GRX50: accepts impedance of 8 to 16 ohms SURROUND SPEAKER: accepts impedance of 16 (MHC-GRX70/GRX70J ohms only) SUPER WOOFER: Voltage 1 V, impedance (except MHC-R770/ 1 kilohm RXD7 (European model)/ RXD9 (European model)) Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range Antenna Antenna terminals Intermediate frequency 87.5 108.0 MHz FM lead antenna 75 ohm unbalanced 10.7 MHz UKV tuner section (3 band (FM-AM-UKV) models only) Tuning range 65.0 74.0 MHz Stereo Plus CD player section Compact disc and digital audio system Laser Semiconductor laser (=780nm) Emission duration: continuous Laser output Max. 44.6 µW* *This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture. Wavelength 780 790 nm Frequency response 2 Hz 20 kHz (±0. 5 dB) Signal-to-noise ratio More than 90 dB Dynamic range More than 90 dB CD OPTICAL DIGITAL OUT (Square optical connector jack, rear panel) Wavelength 660 nm Output Level 18 dBm System 50 AM tuner section Tuning range 2 Band type: North American models: 530 1,710 kHz (with the interval set at 10 kHz) 531 1,710 kHz (with the interval set at 9 kHz) European models: 531 1,602 kHz (with the interval set at 9 kHz) Other models: 531 1,602 kHz (with the interval set at 9 kHz) 530 1,710 kHz (with the interval set at 10 kHz) 3 Band type: Middle Eastern models: MW: 531 1,602 kHz (with the interval set at 9 kHz) SW: 5.95 17.90 MHz (with the interval set at 5 kHz) Other models: MW: 531 1,602 kHz (with the interval set at 9 kHz) 530 1,710 kHz (with the interval set at 10 kHz) SW: 5.95 17.90 MHz (with the interval set at 5 kHz) Antenna AM loop antenna Antenna terminals External antenna terminal Intermediate frequency 450 kHz Speaker SS-GRX9900/GRX9900G for MHC-GRX9900 Speaker system 2-way, 5-unit, bass-reflex type Speaker units Woofer: 15 cm, cone type x2 Tweeter: 5 cm, cone type x3 Nominal impedance 6 ohms Approx. 250 x 430 x 355 mm Dimensions (w/h/d) Mass Approx. 8.5 kg net per speaker SS-RX900D for MHC-RXD9 (German model) Speaker system 3-way, 5-unit, bass-reflex type Speaker units Woofer: 15 cm, cone type x2 Center Tweeter: 5 cm, cone type Side Tweeter: 5 cm, cone type x2 Nominal impedance 8 ohms Dimensions (w/h/d) Approx. You're reading an excerpt. Click here to read official SONY MHCGRX9900 user guide http://yourpdfguides.com/dref/1103237 250 x 430 x 355 mm Mass Approx. 7. 5 kg net per speaker SS-RXD9 for MHC-RXD9 (except for German model) Speaker system 2-way, 5-unit, bass-reflex type Speaker units Woofer: 15 cm, cone type x2 Tweeter: 5 cm, cone type x3 Nominal impedance 8 ohms Dimensions (w/h/d) Approx. 250 x 430 x 355 mm (10 x 17 x 14 in.) Mass Approx. 8.5 kg (16 lb 9 oz) net per speaker SS-RXD80 for MHC-RXD80/SS-RXD7S for MHC-RXD7 (European model) Speaker system 4-way, 5-unit, bass-reflex type, magnetically shielded type Speaker units Woofer: 17 cm, cone type Center Tweeter: 5 cm, cone type Side Tweeter: 5 cm, cone type x2 Super Tweeter: 4 cm, cone type Nominal impedance 8 ohms Dimensions (w/h/d) Approx. 230 x 340 x 320 mm Mass Approx. 5.5 kg net per speaker SS-R770 for MHC-R770 Speaker system 4-way, 5-unit, bass-reflex type Speaker units Woofer: 17 cm, cone type Center Tweeter: 5 cm, cone type Side Tweeter: 5 cm, cone type x2 Super Tweeter: 4 cm, cone type Nominal impedance 8 ohms Dimensions (w/h/d) Approx. 230 x 340 x 320 mm Mass Approx. 5. 5 kg net per speaker SS-GRX70/GRX70G for MHC-GRX70/SS-GRX70J for MHC-GRX70J Speaker system 4-way, 5-unit, bass-reflex type, magnetically shielded type Speaker units Woofer: 17 cm, cone type Center Tweeter: 5 cm, cone type Side Tweeter: 5 cm, cone type x2 Super Tweeter: 4 cm, cone type Nominal impedance 6 ohms Dimensions (w/h/d) Approx. 230 x 340 x 320 mm Mass Approx. 5.5 kg net per speaker continued 51 Specifications (continued) SSRXD7 for MHC-RXD7 (Canadian model) Speaker system 3-way, bass-reflex type Speaker units Woofer: 17 cm, cone type Tweeter: 5 cm, cone type Super Tweeter: 2 cm, dome type Nominal impedance 6 ohms Dimensions (w/h/d) Approx. 220 x 340 x 280 mm Mass Approx. 4 kg net per speaker SSGRX50/GRX50G for MHC-GRX50 Speaker system 3-way, bass-reflex type Speaker units Woofer: 17 cm, cone type Tweeter: 5 cm, cone type Super Tweeter: 2 cm, dome type Nominal impedance 8 ohms Dimensions (w/h/d) Approx. 220 x 340 x 280 mm Mass Approx. 4 kg net per speaker Mass U.S.A. models: MHC-RXD9: Canadian models: MHC-RXD7: MHC-RXD80: European models: MHC-R770/RXD7: MHC-RXD9: Other models: MHC-GRX50: MHC-GRX70/GRX70J: MHC-GRX9900: Supplied accessories: Approx. 10.6 kg (23 lb 6 oz.) Approx. 9. 2 kg Approx. 10.2 kg Approx. 10.1 kg Approx. 10.8 kg Approx. 10.0 kg Approx. 10.6 kg Approx. 12.2 kg AM loop antenna (1) Remote Commander (1) Batteries (2) FM lead antenna (1) Speaker cords (2 for front speakers with jacks only) Front speaker pads (8) Surround speaker SS-SR125 1-way, 1-unit, bass-reflex type 8 cm dia., cone type 16 ohms Approx. 220 x 100 x 195 mm Approx. 1.0 kg net per speaker General Power requirements North American models: 120 V AC, 60 Hz European models: 230 V AC, 50/60 Hz Australian models: 230-240 V AC, 50/60 Hz Mexican models: 120 V AC, 50/60 Hz Israel, South African and Thai models: 220 V AC, 50/60 Hz Other models: 120 V, 220 V or 230 - 240 V AC, 50/60 Hz Adjustable with voltage selector Power consumption U.S.A. models: MHC-RXD9: Canadian model: MHC-RXD7: MHC-RXD80: European models: MHC-R770/RXD7: MHC-RXD9: Other models: MHC-GRX50: MHC-GRX70/GRX70J: MHC-GRX9900: Dimensions (w/h/d) MHCGRX9900/RXD9 Other models: Optional accessories: (MHC-GRX70/GRX70J only) Speaker system Speaker units: Full range Nominal impedance Dimensions (w/h/d) Mass Design and specifications are subject to change without notice. 170 watts 130 watts 170 watts 165 watts 180 watts 160 watts 170 watts 240 watts Approx. 280 x 360 x 395 mm (131/8 x 141/4 x 155/8 in.) Approx. 280 x 340 x 395 mm (131/8 x 131/2 x 155/8 in.) 52 53 Parts identification MHC-GRX70/GRX70J/GRX50/R770/RXD80/RXD7 1 2 3 4 5 6 7 8 9 0 !¡ !TM !£ #º @ª @· @¶ @§ @ @¢ @£ @TM @¡ @º !ª !· !¶!§ ! !¢ 1 2 3 4 5 6 7 8 (power) button POWER SAVE/DEMO button DISC 1~3 buttons DISC SKIP/EXCHANGE button CD § button Disc tray Display CD/tape operating buttons: CD (P (play/pause) TAPE A ( (play) TAPE A 9 (play) TAPE B ( (play) TAPE B 9 (play) p (stop) 9 TUNER/BAND button 0 NON-STOP button KARAOKE PON/MPX button SYNC EQ button SYNC BASS button !¡ Operationg buttons for recording: REC PAUSE/START button HI-DUB button CD SYNC button !TM PHONES jack !£ DBFB button SURROUND button !¢ Deck B § button ! Deck B !§ VOLUME control !¶ ENTER/NEXT button !· 0/), +/ buttons !ª Jog dial @º GROOVE button @¡ Operating buttons for DJ Effects: LOOP button FLASH button 54 MHC-GRX9900/RXD9 1 2 3 4 5 6 7 #º @ª @· @¶ @§ @ @¢ 8 9 0 !¡ !TM !£ @£ @TM @¡ @º !ª !· !¶ !§ ! !¢ @TM @£ @¢ @ Deck A Deck A § button MIX MIC jack Clock/timer operating buttons: CLOCK/TIMER set button TIMER SELECT button @§ MIC LEVEL control @¶ DISPLAY button SPECTRUM ANALYZER button @· For MHC-GRX9900/GRX70/GRX70J/ RXD9/RXD80 only EDIT, DIRECTION, TUNER MEMORY button PLAY MODE, DOLBY NR(, PTY*) button REPEAT, STEREO/MONO button @ª For MHCGRX9900/GRX70/GRX70J/ RXD9/RXD80 EFFECT button FILE SELECT button GEQ CONTROL button P FILE MEMORY button For MHCGRX50/R770/RXD7 EDIT, DIRECTION, TUNER MEMORY button PLAY MODE, DOLBY NR(, PTY*) button REPEAT, STEREO/MONO button FILE SELECT button #º FUNCTION button * For European models only. 55 Index A Adjusting the audio emphasis 29 the sound 28 the volume 12, 14, 17 Antennas 6, 44 Automatic Source Selection 12, 15, 17 K Karaoke 36 S Saving recordings 45 Selecting the audio emphasis 29 Setting the time 7 Shuffle Play 21 Sleep Timer 38 Sound adjustment 28 Speakers 5 Station name 34 L, M Loop 27 N Normal Play 11 O One Touch Play 12, 15, 17 T, U, V Timer falling asleep to music 38 timer recording 40 waking up to music 39 Troubleshooting 46 Tuner 8, 14 Tuning interval 9 B Batteries 7 P, Q Personal file 33 Playing a CD 11 a preset station 14 a tape 16 tracks in random order (Shuffle Play) 21 tracks in the desired order (Program Play) 22 tracks repeatedly (Repeat Play) 20 Presetting radio stations 8 Preset tuning 14 Program Play 22 Protecting recordings 45 PTY 34 C CD player 11, 19-23 CD Synchro Recording 13 Clock setting 7 Connecting. See Hooking up W, X, Y, Z Wake-up timer 39 D, E Display 19 F, G Flash 27 H, I, J Hooking up optional components 41-44 the antennas 6, 44 the power 6 the system 5 R Radio Data System 34 Radio stations presetting 8 tuning in 14 Recording a CD 13 a radio program 15 timer recording 40 Repeat Play 20 Resetting the system 48 Sony 56 Corporation Printed in Hungary . You're reading an excerpt. Click here to read official SONY MHCGRX9900 user guide http://yourpdfguides.com/dref/1103237 Powered by TCPDF (www.tcpdf.org)