Transcript
GLO-RAY
®
Heated Display Cases GRCD & GRHD Series Installation & Operating Manual I & W #07.05.080.00
This manual contains important safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury. If you are unable to understand the contents of this manual, please bring it to the attention of your supervisor. Do not operate this equipment unless you have read and understood the contents of this manual.
Este manual contiene importante información sobre seguridad concerniente al mantenimiento, uso y operación de este producto. Cualquier falla en el seguimiento de las instrucciones contenidas en este manual puede resultar en un serio daño. Si usted no puede entender el contenido de este manual por favor pregunte a su supervisor. No opere este equipo al menos que haya leído y comprendido el contenido de este manual.
CONTENTS Important Owner Information..................................i Introduction.................................................................i Important Safety Instructions ..................................1 Model Descriptions ....................................................3
Operation..................................................................14 Non-Humidified Models ....................................14 Humidified Models ............................................15 Maintenance .............................................................16 General ...............................................................16 Cleaning .............................................................16 Removing Lime & Mineral Deposits.................16 Display Light Bulb Replacement.......................17 Accessories................................................................18 Hatco Limited Warranty.........................................20 Authorized Parts Distributors.................Back Cover
All GRCD Models....................................................3 All GRHD Models ...................................................4
Specifications..............................................................5 Electrical Rating Chart-GRCD Models ...............5 Electrical Rating Chart-GRHD Models ...............7 Plug Configurations .............................................9 Dimensions-GRCD Models .................................9 Dimensions-GRHD Models ...............................10 Installation ................................................................11 All Models..........................................................11 GRCD Models....................................................11 GRHD Models ...................................................12 Location..............................................................13
IMPORTANT OWNER INFORMATION Record the model number, serial number (located on the back of the unit), voltage and purchase date of your Glo-Ray® Heated Display Case in the spaces below. Please have this information available when calling Hatco for service assistance.
Business Hours: 8:00 a.m. to 5:00 p.m. Central Standard Time (Summer Hours: June to September – 8:00 a.m. to 5:00 p.m. C.D.T. Monday through Thursday 8:00 a.m. to 2:30 p.m. C.D.T. Friday) Telephone: (800) 558-0607; (414) 671-6350 Parts & Service Fax: (800) 690-2966 (414) 671-3976 (International) Additional information can be found by visiting our web site at www.hatcocorp.com.
Model No. Serial No. Voltage Date of Purchase
INTRODUCTION Display Cases. We recommend all installation, operating and safety instructions appearing in this manual be read prior to installation or operation of your Hatco Heated Display Case. Safety instructions that appear in this and the words manual after a warning symbol WARNING or CAUTION printed in bold face are very WARNING means there is the possibility important. of serious injury or death to yourself or others. CAUTION means there is the possibility of minor or moderate injury. CAUTION without the symbol signifies the possibility of equipment or property damage only.
Hatco Glo-Ray Heated Display Cases are designed to hold prepared foods for prolonged periods of time while maintaining that “just made” quality. Hatco Display Cases provide the best environment for food products by regulating the air temperature. Display models equipped with humidity control also balance the humidity level. The use of controlled heat maintains serving temperature and texture longer than conventional holding equipment. Glo-Ray Heated Display Cases keep all foods at optimum serving temperatures without affecting quality. These Glo-Ray warmers have prefocused infrared heat from above and a thermostatically controlled heated base to extend the holding times of most foods.
Your Hatco Glo-Ray Heated Display Case is a product of extensive research and field testing. The materials used were selected for maximum durability, attractive appearance and optimum performance. Every unit is thoroughly inspected and tested prior to shipment.
This manual provides the installation, safety and operating instructions for the Glo-Ray Heated Form No. GRCD/HDM-0703
i
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT! Read the following important safety instructions to avoid personal injury or death, and to avoid damage to the equipment or property. WARNINGS
CAUTIONS
To avoid any injury, turn the power switch OFF, unplug the unit from the power source and allow to cool before performing any maintenance.
Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury.
Plug unit into a properly grounded electrical outlet of the correct voltage, size and plug configuration. If the plug and receptacle do not match, contact a qualified electrician to determine the proper voltage and size and install the proper electrical outlet.
For safe and proper operation, the unit must be located a reasonable distance from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur. To prevent any injury or damage locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or its contents from accidentally falling, and strong enough to support the weight of the unit and food displayed.
Only light bulbs which meet or exceed N.S.F standards, specifically designed for food holding areas must be used. Breakage of light bulbs not specifically coated could result in personal injury and/or food contamination. Unit is not waterproof. To avoid electrical shock or personal injury, DO NOT submerge in water. Do not operate if it has been submerged in water.
The unit must be transported in an upright position. If laid on its side, all glass surfaces, pans rails and skirts must be secured with tape, and water must be removed from humidified units.
To avoid electrical shock or personal injury, do not steam clean or use excessive water on the unit.
The National Sanitation Foundation (NSF) requires units over 36" (914 mm) in length or weighing more than 80 lbs. (36 kg) to be either sealed or raised on the installation surface. If this unit cannot be sealed at the point of use, 4" (102 mm) legs are included to allow for proper cleaning access below unit.
To prevent any injury or damage to the unit do not pull unit by power cord. To prevent any injury, discontinue use if power cord is frayed or worn. To prevent any injury, do not place food directly on glass or stainless steel surfaces. Food product must be wrapped or boxed.
Unit is not weatherproof. For safe and proper operation locate the unit indoors where the ambient air temperature is constant and is a minimum of 70°F (21°C).
To avoid any injury, on GRCD-PDG and GRCDH-PDG series units do not allow liquids to spill onto the heated glass shelf.
To avoid any injury on GRCD-PDG and GRCDH-PDG series units do not come in contact with the heated glass shelf while unit is in operation.
To avoid any injury, on GRCD-PDG and GRCDH-PDG series units do not clean heated glass shelf when unit is energized or hot.
1
Form No. GRCD/HDM-0703
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT! Read the following important safety instructions to avoid personal injury or death, and to avoid damage to the equipment or property. WARNINGS
CAUTIONS
If service is required on this unit, contact your Authorized Hatco Service Agent, or contact the Hatco Service Department at 800-558-0607 or 414-671-6350; fax 800-690-2966 or International fax 414-671-3976.
Do not lay unit on the side with the control panel or the front of a curved glass unit, damage to unit could occur. To avoid damage to glass do not remove rubber shipping tabs or tape from glass until legs have been installed.
This product has no “user” serviceable parts. To avoid damage to the unit or injury to personnel, use only Authorized Hatco Service Agents and Genuine Hatco Parts when service is required.
Use only non-abrasive cleaners. Abrasive cleaners could scratch the finish of your Glo-Ray Heated Display Case, marring its appearance and making it susceptible to dirt accumulation.
Genuine Hatco Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in Hatco equipment. It is essential to use Hatco Replacement Parts when repairing Hatco equipment. Failure to use Hatco Replacement Parts may subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn.
Form No. GRCD/HDM-0703
Do not allow the glass shelf to overheat on GRCD-PDG and GRCDH-PDG series units. Overheating may cause the food containers to melt or soften. Do not use food pans, ceramic dishes, or abrasive materials on heated glass shelves. Food pans, ceramic dishes, and abrasive materials may scratch the glass shelf marring its appearance and making it susceptible to dirt accumulation. It is recommended that glass shelves be used for food products contained in disposable paper or plastic containers or wrapping.
2
MODEL DESCRIPTIONS ALL GRCD MODELS All GRCD models are constructed of stainless steel and aluminum with a tempered curved front glass panel and glass sides. The display cases feature a specially designed thermostatically controlled heated base, infrared upper heating elements, incandescent lights, 4" (102 mm) appliance legs, and a cord and plug set.
GRCD-1P (Single Tier) The GRCD-1P is designed to hold up to one standard full size food pan. The unit has one hinged door.
GRCD-1PD (Dual Tier) The GRCD-1PD is designed to hold up to one half size or two 1/3 size standard food pans on the top stainless steel shelf, and one standard full size food pan on the bottom. The unit has one hinged door.
Figure 1. Glo-Ray Model GRCD-2PD Shown
GRCD-2P (Single Tier) The GRCD-2P is designed to hold up to two standard full size food pans. The unit has two sliding rear doors.
GRCD-2PD (Dual Tier) The GRCD-2PD is designed to hold up to one full size plus a 1/3 size standard food pan on the top stainless steel shelf, and two standard full size food pans on the bottom. The unit has two sliding rear doors.
GRCD-2PDG (Dual Tier) Figure 2. Glo-Ray Model GRCDH-2PD Shown
The GRCD-2PDG features an upper heated glass shelf designed to hold hot wrapped or boxed food and a lower heated base that holds two standard full size food pans. The unit has two sliding rear doors.
GRCDH SERIES (Humidified) The GRCDH Models (Humidified) are similar to the GRCD Models (Non-Humidified) listed above but come equipped with a thermostatically-controlled, adjustable humidity system. A 3 quart (2.8 liter) capacity heated water trough in the base provides humidity to extend food holding time up to four hours.
GRCD-3P (Single Tier) The GRCD-3P is designed to hold three standard full size food pans. The unit has two sliding rear doors.
GRCD-3PD (Dual Tier)
NOTE: GRCD models cannot be converted to GRCDH models.
The GRCD-3PD is designed to hold up to two full size standard food pans on the top stainless steel shelf and three standard food pans on the bottom. The unit has two sliding rear doors.
GRCD-3PDG (Dual Tier) The GRCD-3PDG features an upper heated glass shelf designed to hold hot wrapped or boxed food and a lower heated base that holds three standard full size food pans. The unit has two sliding rear doors.
3
Form No. GRCD/HDM-0703
MODEL DESCRIPTIONS ALL GRHD MODELS All GRHD models are constructed of stainless steel and aluminum with sliding doors on the back side, and full view tempered glass sides. The display cases feature a thermostatically controlled heated base, infrared upper heating elements, incandescent lights, 4" (102 mm) appliance legs, and a cord and plug set.
GRHD-2P (Single Tier) The GRHD-2P is designed to hold up to two standard, full size food pans.
GRHD-2PD (Dual Tier) The GRHD-2PD is designed to hold two half size standard food pans on the top shelf and two standard full size food pans on the bottom.
Figure 3. Glo-Ray Model GRHD-2P Shown
GRHD-3P (Single Tier) The GRHD-3P is designed to hold three standard food pans.
GRHD-3PD (Dual Tier) The GRHD-3PD is designed to hold three half size standard food pans on the top shelf and three standard food pans on the bottom.
GRHD-4P (Single Tier) The GRHD-4P is designed to hold four standard food pans.
GRHD-4PD (Dual Tier)
Figure 4. Glo-Ray Model GRHDH-2PD Shown
The GRHD-4PD is designed to hold four half size standard food pans or two full size standard food pans on the top shelf, and four standard food pans on the bottom.
NOTE: GRHDH models are equipped with humidity on the bottom shelf only. NOTE: GRHD models cannot be converted to GRHDH models.
GRHDH MODELS (Humidified) The GRHDH Models (Humidified) are similar to the GRHD Models (Non-Humidified) but come equipped with a thermostatically controlled, adjustable humidity system. A 3 or 6 quart (2.8 or 5.7 liter) capacity heated water trough in the base provides humidity to extend food holding time up to four hours.
Form No. GRCD/HDM-0703
4
SPECIFICATIONS ELECTRICAL RATING CHART - GRCD MODELS Model
Voltage
Watts
Amps
Plug Configuration
Shipping Weight
GRCD-1P
100 120 220-230CE 220 230-240CE 240
410 410 443 405 425 425
4.1 3.4 1.9 1.8 1.8 1.8
NEMA 5-15P NEMA 5-15P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
60 lbs. (27 kg) 60 lbs. (27 kg) 60 lbs. (27 kg) 60 lbs. (27 kg) 60 lbs. (27 kg) 60 lbs. (27 kg)
GRCD-1PD
100 120 220-230CE 220 230-240CE 240
860 860 989 905 905 905
8.6 7.2 4.3 4.1 3.8 3.8
NEMA 5-15P NEMA 5-15P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
98 lbs. (45 kg) 98 lbs. (45 kg) 98 lbs. (45 kg) 98 lbs. (45 kg) 98 lbs. (45 kg) 98 lbs. (45 kg)
GRCD-2P
100 120 220-230CE 220 230-240CE 240
780 780 776 710 780 780
7.8 6.5 3.4 3.2 3.3 3.3
NEMA 5-15P NEMA 5-15P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
104 lbs. (47 kg) 104 lbs. (47 kg) 104 lbs. (47 kg) 104 lbs. (47 kg) 104 lbs. (47 kg) 104 lbs. (47 kg)
GRCD-2PD
100 120 220-230CE 220 230-240CE 240
1210 1210 1177 1077 1285 1285
12.1 10.1 5.1 4.9 5.4 5.4
NEMA 5-15P NEMA 5-15P* CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
170 lbs. (77 kg) 170 lbs. (77 kg) 170 lbs. (77 kg) 170 lbs. (77 kg) 170 lbs. (77 kg) 170 lbs. (77 kg)
120
1130
9.4
NEMA 5-15P ♦
170 lbs. (77 kg)
GRCD-3P
100 120 220-230CE 220 230-240CE 240
1005 1005 1000 915 1005 1005
10.1 8.4 4.4 4.2 4.2 4.2
NEMA 5-15P NEMA 5-15P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
152 lbs. (69 kg) 152 lbs. (69 kg) 152 lbs. (69 kg) 152 lbs. (69 kg) 152 lbs. (69 kg) 152 lbs. (69 kg)
GRCD-3PD
120 220-230CE 220 230-240CE 240
1710 1570 1434 1710 1710
14.3 6.8 6.5 7.1 7.1
NEMA 5-15P* CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
218 lbs. (99 kg) 218 lbs. (99 kg) 218 lbs. (99 kg) 218 lbs. (99 kg) 218 lbs. (99 kg)
120
1725
14.3
NEMA 5-15P♦
218 lbs. (99 kg)
GRCD-2PDG
GRCD-3PDG
* NEMA 5-20P for Canada. † Not available for Canada with Backlit Base Sign Holder. ♦ NOTE: GRCD-PDG series contain a GFCI (Ground Fault Circuit Interrupt) built into the unit. The electrical information in the shaded areas pertains to Export models only.
5
Form No. GRCD/HDM-0703
SPECIFICATIONS ELECTRICAL RATING CHART - GRCD MODELS Model
Voltage
Watts
Amps
Plug Configuration
GRCDH-1P
100 120 220-230CE 220 230-240CE 240
660 660 693 634 697 697
6.6 5.5 3.0 2.9 2.9 2.9
NEMA 5-15P NEMA 5-15P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
71 lbs. (32 kg) 71 lbs. (32 kg) 71 lbs. (32 kg) 71 lbs. (32 kg) 71 lbs. (32 kg) 71 lbs. (32 kg)
GRCDH-1PD
100 120 220-230CE 220 230-240CE 240
1038 1110 1201 1099 1177 1177
10.4 9.3 4.9 5.0 4.9 4.9
NEMA 5-15P NEMA 5-15P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
100 lbs. (45 kg) 100 lbs. (45 kg) 100 lbs. (45 kg) 100 lbs. (45 kg) 100 lbs. (45 kg) 100 lbs. (45 kg)
GRCDH-2P
100 120 220-230CE 220 230-240CE 240
976 1030 1026 939 1052 1052
9.8 8.6 4.5 4.3 4.4 4.4
NEMA 5-15P NEMA 5-15P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
124 lbs. (56 kg) 124 lbs. (56 kg) 124 lbs. (56 kg) 124 lbs. (56 kg) 124 lbs. (56 kg) 124 lbs. (56 kg)
GRCDH-2PD
100 120 220-230CE 220 230-240CE 240
1352 1460 1427 1306 1532 1532
13.5 12.2 6.2 5.9 6.4 6.4
NEMA 5-15P NEMA 5-15P* CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
174 lbs. (79 kg) 174 lbs. (79 kg) 174 lbs. (79 kg) 174 lbs. (79 kg) 174 lbs. (79 kg) 174 lbs. (79 kg)
120
1380
11.5
NEMA 5-15P♦
174 lbs. (79 kg)
GRCDH-3P
100 120 220-230CE 220 230-240CE 240
1201 1255 1251 1145 1277 1277
12.0 10.5 5.4 5.2 5.3 5.3
NEMA 5-15P NEMA 5-15P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
172 lbs. (78 kg) 172 lbs. (78 kg) 172 lbs. (78 kg) 172 lbs. (78 kg) 172 lbs. (78 kg) 172 lbs. (78 kg)
GRCDH-3PD
120 220-230CE 220 230-240CE 240
1960 1818 1663 1989 1982
16.0 7.9 7.6 8.3 8.3
NEMA 5-20P† CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
222 lbs. (101 kg) 222 lbs. (101 kg) 222 lbs. (101 kg) 222 lbs. (101 kg) 222 lbs. (101 kg)
120
1915
15.9
NEMA 5-20P♦
222 lbs. (101 kg)
GRCDH-2PDG
GRCDH-3PDG
* NEMA 5-20P for Canada. † Not available for Canada with Backlit Base Sign Holder. ♦ NOTE: GRCD-PDG series contain a GFCI (Ground Fault Circuit Interrupt) built into the unit. The electrical information in the shaded areas pertains to Export models only.
Form No. GRCD/HDM-0703
6
Shipping Weight
SPECIFICATIONS ELECTRICAL RATING CHART - GRHD MODELS Model
Voltage
Watts
Amps
Plug Configuration
Shipping Weight
GRHD-2P
100 120 220-230CE 220 230-240CE 240
940 940 1131 1035 940 940
9.4 7.8 4.9 4.7 3.9 3.9
NEMA 5-15P NEMA 5-15P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
120 lbs. (54 kg) 120 lbs. (54 kg) 120 lbs. (54 kg) 120 lbs. (54 kg) 120 lbs. (54 kg) 120 lbs. (54 kg)
GRHD-2PD
120 220-230CE 220 230-240CE 240
1310 1333 1220 1310 1310
10.9 5.8 5.6 5.5 5.5
NEMA 5-15P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
168 lbs. (76 kg) 168 lbs. (76 kg) 168 lbs. (76 kg) 168 lbs. (76 kg) 168 lbs. (76 kg)
GRHD-3P
120 220-230CE 220 230-240CE 240
1350 1601 1465 1350 1350
11.3 7.0 6.7 5.6 5.6
NEMA 5-15P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
150 lbs. (68 kg) 150 lbs. (68 kg) 150 lbs. (68 kg) 150 lbs. (68 kg) 150 lbs. (68 kg)
GRHD-3PD
120 220-230CE 220 230-240CE 240
1755 1749 1600 1755 1755
14.6 7.9 7.3 7.3 7.3
NEMA 5-15P* CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
188 lbs. (85 kg) 188 lbs. (85 kg) 188 lbs. (85 kg) 188 lbs. (85 kg) 188 lbs. (85 kg)
GRHD-4P
120 120/208 120/240 220-230CE 220 230-240CE 240
1785 1785 1785 2109 1930 1785 1785
14.9 7.7 7.7 9.2 8.8 7.4 7.4
NEMA 5-15P* NEMA 14-20P NEMA 14-20P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
215 lbs. (98 kg) 215 lbs. (98 kg) 215 lbs. (98 kg) 215 lbs. (98 kg) 215 lbs. (98 kg) 215 lbs. (98 kg) 215 lbs. (98 kg)
GRHD-4PD
120 120/208 120/240 220-230CE 220 230-240CE 240
2660 2660 2660 2661 2435 2661 2660
22.2 12.4 12.4 11.6 11.1 11.1 11.1
NEMA 5-30P‡ NEMA 14-20P NEMA 14-20P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
230 lbs. (104 kg) 230 lbs. (104 kg) 230 lbs. (104 kg) 230 lbs. (104 kg) 230 lbs. (104 kg) 230 lbs. (104 kg) 230 lbs. (104 kg)
* NEMA 5-20P for Canada. ‡ Not available for Canada. The electrical information in the shaded areas pertains to Export models only.
7
Form No. GRCD/HDM-0703
SPECIFICATIONS ELECTRICAL RATING CHART - GRHD MODELS Model
Voltage
Watts
Amps
Plug Configuration
GRHDH-2P
100 120 220-230CE 220 230-240CE 240
1190 1190 1289 1179 1212 1212
11.9 9.9 5.6 5.4 5.0 5.0
NEMA 5-15P NEMA 5-15P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
120 lbs. (55 kg) 120 lbs. (55 kg) 120 lbs. (55 kg) 120 lbs. (55 kg) 120 lbs. (55 kg) 120 lbs. (55 kg)
GRHDH-2PD
120 220-230CE 220 230-240CE 240
1560 1671 1529 1582 1582
13.0 7.3 7.0 6.6 6.6
NEMA 5-15P* CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
175 lbs. (79 kg) 175 lbs. (79 kg) 175 lbs. (79 kg) 175 lbs. (79 kg) 175 lbs. (79 kg)
GRHDH-3P
120 220-230CE 220 230-240CE 240
1600 1731 1584 1622 1622
13.3 7.5 7.2 6.8 6.8
NEMA 5-15P* CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
162 lbs. (73 kg) 162 lbs. (73 kg) 162 lbs. (73 kg) 162 lbs. (73 kg) 162 lbs. (73 kg)
GRHDH-3PD
120 220-230CE 220 230-240CE 240
2005 2141 1959 2027 2027
16.7 9.3 8.9 8.4 8.4
NEMA 5-20P‡ CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
200 lbs. (91 kg) 200 lbs. (91 kg) 200 lbs. (91 kg) 200 lbs. (91 kg) 200 lbs. (91 kg)
GRHDH-4P
120 120/208 120/240 220-230CE 220 230-240CE 240
2285 2285 2285 2463 2253 2329 2329
19.0 9.8 9.8 10.7 10.2 9.7 9.7
NEMA 5-30P‡ NEMA 14-20P NEMA 14-20P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
215 lbs. (98 kg) 215 lbs. (98 kg) 215 lbs. (98 kg) 215 lbs. (98 kg) 215 lbs. (98 kg) 215 lbs. (98 kg) 215 lbs. (98 kg)
GRHDH-4PD
120 120/208 120/240 220-230CE 220 230-240CE 240
3160 3160 3160 3375 3088 3204 3204
26.3 13.9 13.9 14.7 14.0 13.4 13.4
NEMA 5-30P‡ NEMA 14-20P NEMA 14-20P CEE 7/7 Schuko CEE 7/7 Schuko BS 1363 BS 1363
240 lbs. (109 kg) 240 lbs. (109 kg) 240 lbs. (109 kg) 240 lbs. (109 kg) 240 lbs. (109 kg) 240 lbs. (109 kg) 240 lbs. (109 kg)
* NEMA 5-20P for Canada. ‡ Not available for Canada. The electrical information in the shaded areas pertains to Export models only.
Form No. GRCD/HDM-0703
8
Shipping Weight
SPECIFICATIONS PLUG CONFIGURATIONS Units are supplied from the factory with an electrical cord and plug. See Figure 5. ! WARNING Plug unit into a properly grounded electrical outlet of the correct voltage, size and plug configuration. If the plug and receptacle do not match, contact a qualified electrician to determine the proper voltage and size and install the proper electrical outlet.
NEMA 5-15P
NEMA 5-20P
NEMA 5-30P
NEMA 14-20P
CEE 7/7 Schuko
BS-1363
DIMENSIONS - GRCD MODELS Model GRCD-1P
(A) Width (B) Length (C) Height*
26" (660 mm) GRCD-1PD 26" (660 mm) GRCD-2P 26" (660 mm) GRCD-2PD 26" (660 mm) GRCD-2PDG 26" (660 mm) GRCD-3P 26" (660 mm) GRCD-3PD 26" (660 mm) GRCD-3PDG 26" (660 mm) GRCDH-1P 26" (660 mm) GRCDH-1PD 26" (660 mm) GRCDH-2P 26" (660 mm) GRCDH-2PD 26" (660 mm) GRCDH-2PDG 26" (660 mm) GRCDH-3P 26" (660 mm) GRCDH-3PD 26" (660 mm) GRCDH-3PDG 26" (660 mm)
20-5/8" (524 mm) 20-5/8" (524 mm) 32-1/2" (826 mm) 32-1/2" (826 mm) 32-1/2" (826 mm) 45-1/2" (1156 mm) 45-1/2" (1156 mm) 45-1/2" (1156 mm) 20-5/8" (524 mm) 20-5/8" (524 mm) 32-1/2" (826 mm) 32-1/2" (826 mm) 32-1/2" (826 mm) 45-1/2" (1156 mm) 45-1/2" (1156 mm) 45-1/2" (1156 mm)
24" (610 mm) 31-3/4" (807 mm) 24" (610 mm) 31-3/4" (807 mm) 31-3/4" (807 mm) 24" (610 mm) 31-3/4" (807 mm) 31-3/4" (807 mm) 24" (610 mm) 31-3/4" (807 mm) 24" (610 mm) 31-3/4" (807 mm) 24" (610 mm) 24" (610 mm) 31-3/4" (807 mm) 31-3/4" (807 mm)
Figure 5. Plug Configurations
A
B
C
Figure 6. Dimensions - GRCD Models
NOTE: On dual shelf units, the interior usable space dimension for the upper shelf is as follows: - 15" (381 mm) deep - 6-3/4" (172 mm) high with pan enclosure installed - 9" (229 mm) high without pan enclosure and metal shelf - 10-1/4" (260 mm) high without pan enclosure and glass shelf - 18" (457 mm) wide for -1PD model - 30" (762 mm) wide for -2PD models - 43" (1092 mm) wide for -3PD models NOTE: On dual shelf units, the lower shelf interior height dimension is as follows: - 8" (203 mm) with pan enclosure installed - 10-1/4" (260 mm) without pan enclosure NOTE: On single shelf units, the interior height dimension is as follows: - 12-1/8" (308 mm) with pan enclosure installed - 14-1/8" (359 mm) without pan enclosure
* Height includes 4" (102 mm) for legs.
9
Form No. GRCD/HDM-0703
SPECIFICATIONS DIMENSIONS - GRHD MODELS Model
(A) Width (B) Length (C) Height*
Model
(A) Width (B) Length (C) Height*
GRHD-2P
26" (660 mm)
32-1/2" (826 mm)
25" (635 mm)
GRHDH-2P
26" (660 mm)
33-3/8" (848 mm)
25" (635 mm)
GRHD-2PD
26" (660 mm)
32-1/2" (826 mm)
30" (762 mm)
GRHDH-2PD
26" (660 mm)
33-3/8" (848 mm)
30" (762 mm)
GRHD-3P
26" (660 mm)
45-1/2" (1156 mm)
25" (635 mm)
GRHDH-3P
26" (660 mm)
46-3/8" (1178 mm)
25" (635 mm)
GRHD-3PD
26" (660 mm)
45-1/2" (1156 mm)
30" (762 mm)
GRHDH-3PD
26" (660 mm)
46-3/8" (1178 mm)
30" (762 mm)
GRHD-4P
26" (660 mm)
58-1/2" (1486 mm)
25" (635 mm)
GRHDH-4P
26" (660 mm)
59-3/8" (1508 mm)
25" (635 mm)
GRHD-4PD
26" (660 mm)
58-1/2" (1486 mm)
30" (762 mm)
GRHDH-4PD
26" (660 mm)
59-3/8" (1508 mm)
30" (762 mm)
* Height includes 4" (102 mm) for legs.
* Height includes 4" (102 mm) for legs.
B
A
C
Figure 7. Dimensions - GRHD Models
Form No. GRCD/HDM-0703
10
INSTALLATION ALL MODELS
Leg Adjustment
! CAUTION The National Sanitation Foundation (NSF) requires units over 36" (914 mm) in length or weighing more than 80 lbs. (36 kg) to be either sealed or raised on the installation surface. If this unit cannot be sealed at the point of use, 4" (102 mm) legs are included to allow for proper cleaning access below unit.
Adjust leg using a 9/16” (14 mm) open-end wrench and turning bottom of leg accordingly.
Leg Installation
CAUTION To avoid damage to glass do not remove rubber shipping tabs or tape from glass until legs have been installed.
GRCD MODELS 1. Remove plastic bag containing 4 adjustable legs from inside the unit.
Figure 8. Adjustable Legs
2. Remove pan rail (GRCD units) or pan skirts, water trough (GRCDH units) and front glass.
Left Rear Door*
Right Rear Door* Door Glides (2 ea. door)
3. Carefully lay unit on its side (requires 2 people). Install legs to bottom of unit as shown in Figure 8. Hand tighten legs until snug. Do not overtighten. Return unit to the upright position.
Front Curved Glass
CAUTION Do not lay unit on the side with the control panel or the front of a curved glass unit, damage to unit could occur. NOTE: Legs are adjustable for leveling the unit. Use a 9/16" (14 mm) open-end wrench to make leveling adjustments once the unit is placed in final position.
Pan Divider (GRCDH models)
4. Remove rear doors on 2-pan and 3-pan models by grasping the door edges then lifting up and out of the bottom channel. Discard the protective cardboard from top of each door. NOTE: Do not remove the plastic glides from top of door glass. See Figure 9.
Water Trough (GRCDH models)
5. Remove tape and protective film from all outside surfaces of unit. 6. Remove front curved glass by rotating it partially forward and lifting straight up and off. Discard rubber packing strips. 7. Remove tape and protective film from all internal parts and surfaces.
Pan Rail (GRCD models)
8. Install pan rail (GRCD units) or pan skirts and water trough (GRCDH units).
Pan Skirt (GRCDH models)
* 1-Pan models have a hinged door.
9. Install rear doors and front curved glass.
Figure 9. Exploded View - GRCD Models
11
Form No. GRCD/HDM-0703
INSTALLATION GRHD MODELS Rear Doors
1. Remove plastic bag containing 4 adjustable legs from inside the unit. 2. Remove all components from inside the unit. See Figure 10.
Door Glides (2 ea. door)
3. Remove all doors by grasping the door edges then lifting up and out of the bottom channel. See Figure 10. Discard the protective cardboard from top of each door. NOTE: Do not remove the plastic glides from top of door glass. See Figure 10. 4. Carefully lay unit on its side (requires 2 people). Install legs to bottom of unit as shown in Figure 8. Hand tighten legs until snug. Do not overtighten. Return unit to the upright position. NOTE: If your unit is equipped with optional Slant Leg Kit, see Accessories for installation instructions. CAUTION Do not lay unit on the side with the control panel or the front of a curved glass unit, damage to unit could occur.
Pan Divider (GRHDH models) Side Glass Water Trough (GRHDH models)
NOTE: Legs are adjustable for leveling the unit. Use a 9/16" (14 mm) open-end wrench to make leveling adjustments once the unit is placed in final position. 5. Remove tape and protective film from all surfaces of unit. 6. Install pan rail (GRHD units) or pan skirt, divider and water trough (GRHDH units).
Pan Rail (GRHD models)
7. Re-install rear doors.
Pan Skirt (GRHDH models)
Figure 10. Exploded View - GRHD Models
NOTE: If your unit is equipped with optional Sandwich Chutes and/or Display Sign Holder, see Accessories for installation instructions.
Form No. GRCD/HDM-0703
12
INSTALLATION ! WARNING Unit is not waterproof. To avoid electrical shock or personal injury. DO NOT submerge in water. Do not operate if it has been submerged in water.
LOCATION - ALL MODELS ! CAUTION The unit must be transported in an upright position. If laid on its side, all glass surfaces, pans rails and skirts must be secured with tape, and water must be removed from the unit.
! CAUTION Unit is not weatherproof. For safe and proper operation locate the unit indoors where the ambient air temperature is constant and is a minimum of 70°F (21°C).
! CAUTION To prevent any injury or damage locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or its contents from accidentally falling, and strong enough to support the weight of the unit and food displayed. ! CAUTION For safe and proper operation, the unit must be located a reasonable distance from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur.
13
Form No. GRCD/HDM-0703
OPERATION ! CAUTION Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury.
Center Heat Control* Top & Center Heat Indicators*
! WARNING To prevent any injury or damage to the unit do not pull unit by power cord.
HATCO GLO-RAY ON
! WARNING To prevent any injury, discontinue use if power cord is frayed or worn.
OFF
Power Switch Top Heat Control
! WARNING To prevent any injury, do not place food directly on glass or stainless steel surfaces. Food product must be wrapped or boxed.
Base Heat Control *Dual tier models only. Figure 11. Control Panel – Non-Humidified Models
! CAUTION To avoid any injury on GRCD-PDG and GRCDH-PDG series units do not come in contact with the heated glass shelf while unit is in operation.
NON-HUMIDIFIED MODELS 1. Plug cabinet into a properly grounded electrical outlet of the correct voltage, size and plug configuration. See Specifications for details.
! WARNING To avoid any injury, on GRCD-PDG and GRCDH-PDG series units do not allow liquids to spill onto the heated glass shelf.
2. Turn the Power Switch to the ON position. See Figure 11. 3. On start-up set all heat controls at maximum to assure safe food holding.
CAUTION Do not allow the glass shelf to overheat on GRCD-PDG and GRCDH-PDG series units. Overheating may cause the food containers to melt or soften.
On dual tier models, the Top and Center Heat Indicators will light when controls are in the ON position.
CAUTION Do not use food pans, ceramic dishes, or abrasive materials on heated glass shelves. Food pans, ceramic dishes, and abrasive materials may scratch the glass shelf marring its appearance and making it susceptible to dirt accumulation. It is recommended that glass shelves be used for food products contained in disposable paper or plastic containers or wrapping.
NOTE: Temperature settings may vary depending upon product make-up and consistency. 4. Allow unit 30 minutes to reach operating temperature.
NOTE: Scratches on heated glass shelves are not covered under warranty.
Form No. GRCD/HDM-0703
14
OPERATION HUMIDIFIED MODELS
Center Heat Control*
Humidity Selector Control
1. Plug cabinet into a properly grounded electrical outlet of the correct voltage, size and plug configuration. See Specifications for details.
Reset Button
2. Remove the center slotted pan divider from the water trough.
Top & Center Heat Indicators*
HATCO GLO-RAY ON
OFF
3. Turn the Power Switch to the ON position. See Figure 12.
Power Switch Low Water Indicator Humidity On Indicator
4. Rotate the Humidity Selector Control to the desired position. The green Humidity On Indicator will light up to show that humidity is on. The red Low Water Indicator will light when the water trough is empty.
Top Heat Control Base Heat Control
*Dual tier models only.
5. Fill the water trough with softened or distilled water. The trough has a 3 quart (2.8 liter) capacity. If the red Low Water Indicator is on, press the Reset Button.
NOTE: Temperature and humidity settings may vary depending upon product make-up and consistency.
NOTE: Use of softened or distilled water is recommended to preserve the life of electrical and mechanical components. If hard water is used, the trough will require periodic cleaning and deliming. See Maintenance section for deliming instructions.
NOTE: The trough capacity permits uninterrupted operation for approximately 4 hours, depending on the settings and how frequently the door is opened. When the red Low Water Indicator lamp is lit, add water to the reservoir and press the Reset Button.
Figure 12. Control Panel – Humidified Models
6. Re-install the center Pan Divider.
8. Allow unit 30 minutes to reach operating temperature.
7. On start-up set all heat controls at maximum to assure safe food holding.
9. At the end of the day or shift, turn unit off and allow to cool down. Remove and clean the water trough.
On dual tier models, the Top and Center Heat Indicators will light when controls are in the ON position.
15
Form No. GRCD/HDM-0703
MAINTENANCE REMOVING LIME & MINERAL DEPOSITS - HUMIDIFIED MODELS
GENERAL Hatco Glo-Ray® Heated Display Cases are designed for maximum durability and performance, with minimum maintenance.
1. Turn the power switch off and unplug the unit from its power source.
! WARNING To avoid any injury, turn the power switch OFF, unplug the unit from the power source and allow to cool before performing any maintenance.
2. After the unit has cooled down, remove the water trough. 3. Fill the water trough with a mixture of water and delimer.
CLEANING
NOTE: The de-limer used should be a safe, non-toxic, non-corrosive solution. Follow the delimer’s instructions for proper mixture of water and de-limer solution.
To preserve the bright finish of the Glo-Ray Heated Display Case, it is recommended that the exterior and interior surfaces be wiped daily with a damp cloth. Food pans should be removed and washed. Stubborn stains may be removed with a good stainless steel cleaner or a non-abrasive cleaner. Hard to reach areas should be cleaned with a small brush and mild soap.
4. Allow the trough to stand with the mixture for the recommended period of time. (The time required will vary depending on the solution used and amount of deposits in the trough.)
CAUTION Use only non-abrasive cleaners. Abrasive cleaners could scratch the finish of your Glo-Ray Heated Display Case, marring its appearance and making it susceptible to dirt accumulation.
5. After the deliming period, drain the solution from the trough. 6. Continue to fill and rinse the trough with water only, until the trough is clean.
! WARNING To avoid electrical shock or personal injury, do not steam clean or use excessive water on the unit.
7. Install the trough into the unit. Plug the display case power cord into its power source and fill the trough as usual for daily operation.
! WARNING To avoid any injury, on GRCD-PDG and GRCDH-PDG series units do not clean heated glass shelf when unit is energized or hot.
NOTE: The lime and mineral content of the water used for daily operation will determine how often de-liming procedure must be performed.
Clean the glass sides and heated glass shelves using a common glass cleaner and soft non-abrasive cloth. NOTE: Scratches on heated glass shelves are not covered under warranty. NOTE: If the water used on GRCDH/GRHDH models (humidified) has an excessive amount of lime or mineral content, use the following instructions for periodic cleaning and de-liming of the water trough.
Form No. GRCD/HDM-0703
16
MAINTENANCE ! WARNING If service is required on this unit, contact your Authorized Hatco Service Agent, or contact the Hatco Service Department at 800-558-0607 or 414-671-6350; fax 800-690-2966 or International fax 414-671-3976.
DISPLAY LIGHT BULB REPLACEMENT The display lights are incandescent light bulbs which illuminate the warming area. These bulbs have a special coating to guard against injury and food contamination in the event of breakage. 1. To replace a light bulb, disconnect the power supply and wait until the unit has cooled.
! WARNING This product has no “user” serviceable parts. To avoid damage to the unit or injury to personnel, use only Authorized Hatco Service Agents and Genuine Hatco Parts when service is required.
2. Bulbs have a threaded base. Unscrew the light bulb from the unit and replace it with a new specially coated incandescent bulb.
! WARNING Genuine Hatco Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in Hatco equipment. It is essential to use Hatco Replacement Parts when repairing Hatco equipment. Failure to use Hatco Replacement Parts may subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn.
NOTE: Hatco shatter-resistant light bulbs meet N.S.F. standards for food holding and display areas. For 120, 120/208 and 120/240 Volt applications, use Hatco part #02.30.043.00. For 220 or 240 Volt applications, use Hatco part # 02.30.058.00. ! WARNING Only light bulbs which meet or exceed N.S.F. standards, specifically designed for food holding areas must be used. Breakage of light bulbs not specifically coated could result in personal injury and/or food contamination.
GROUND FAULT CIRCUIT INTERRUPT The GRCD-PDG series is supplied with a built in Ground Fault Circuit Interrupt (GFCI) which is designed to turn electrical power off to the internal components when there is a short circuit or electrical fault. To reset the “GFCI” push the red reset button in. If the “GFCI” continues to trip, contact your local Authorized Hatco Service Agency.
17
Form No. GRCD/HDM-0703
ACCESSORIES SLANT LEG KIT (GRHD Models Only without Humidity) The Slant Leg Kit tilts the unit in a forward position for optimum display of food product. 1. Remove the pan rail or sandwich chutes. 2. Carefully lay unit on its side (requires two people). CAUTION Do not lay unit on the side with the control panel or the front of a curved glass unit, damage to unit could occur. 3. Remove screws from bottom right side and bottom left side of unit. See Figure 13. Figure 13. Slant Leg Kit - GRHD Models without Humidity
4. Position slant leg over holes with long leg towards the rear, and install using original screws.
Knurled Thumbscrew End Piece
5. Feet have an adjustable range of 3/4" to 1-1/2" (3 - 6 mm). Return unit to upright position and adjust feet to desired height.
SANDWICH CHUTES (GRHD Models Only) Sandwich Chutes provide for upright display of sandwich products. NOTE: The following assembly procedure is the same for both single and double tier units. 1. Remove protective film from all parts. 2. Remove the side glass panels by pushing in the spring loaded pins and removing panels. 3. Install the end pieces to the unit using knurled thumbscrews. Tighten securely but do not overtighten. See Figure 14.
Figure 14. Sandwich Chutes - GRHD Models Only
4. Re-install side glass panels. 5. Install separator and sandwich chutes.
DISPLAY SIGN HOLDER (GRHD Models Only) The display sign holder allows you to customize your unit with product name and/or graphics. 1. Remove screws from upper left and right side of unit as shown in Figure 15. 2. Install sign holder using original screws. 3. Insert sign (not included) and plexiglas cover. Figure 15. Display Sign Holder - GRHD Models Only Form No. GRCD/HDM-0703
18
ACCESSORIES DESIGNER COLORS
BACKLIT BASE (GRCD 2-Pan and 3-Pan Models Only)
Choose an optional Designer color in place of the stainless steel exterior finish to match your décor.
The optional backlit base allows you to showcase your product by customizing your display cabinet.
DOUBLE-SIDED OPENING (GRHD Models Only)
MIRROR GLASS DOOR
GRHD models can be configured for double-sided opening by installing the optional front doors.
One way mirror enhances food displays on customer side while allowing operator to review food from rear.
SLIDING OR FLIP-UP STYLE DOORS (GRHD Models Only)
DISPLAY SIGN HOLDER (GRHD Models Only)
Sliding or flip-up style doors are available.
A metal holder with acrylic window is available to promote product (sign not included).
BREATH PROTECTORS (GRHD Models Only)
SLANT LEG KIT
7½" (191 mm) breath protectors are available in lieu of sliding doors.
Available for non-humidified models only.
PAN SKIRT
Stainless steel food holding pans are available in either 2½" (64 mm) or 4" (102 mm) depths. These pans are offered in full size, half size or third size. Optional wire trivets prevent foods from touching pan bottom.
PANS & TRIVETS
Available for top metal shelf on two tiered models and bottom shelf of non-humidified units.
19
Form No. GRCD/HDM-0703
HATCO LIMITED WARRANTY THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR PATENT OR OTHER INTELLECTUAL PROPERTY RIGHT INFRINGEMENT. Without limiting the generality of the foregoing, SUCH WARRANTIES DO NOT COVER: Coated incandescent light bulbs, fluorescent lights, lamp warmer heat bulbs, glass components, Product failure in booster tank, fin tube heat exchanger, or other water heating equipment, caused by liming, sediment buildup, chemical attack or freezing, Product misuse, tampering or misapplication, improper installation, application of improper voltage, or recalibration of thermostats or high limit switches, or transportation damage.
1. PRODUCT WARRANTY Hatco warrants the products that it manufactures (the “Products”) to be free from defects in materials and workmanship, under normal use and service, for a period of one (1) year from the date of purchase when installed and maintained in accordance with Hatco’s written instructions or 18 months from the date of shipment from Hatco. Buyer must establish the product’s purchase date by returning Hatco’s Warranty Registration Card or by other means satisfactory to Hatco in its sole discretion. Hatco warrants the following Product components to be free from defects in materials and workmanship from the date of purchase (subject to the foregoing conditions) for the period(s) of time and on the conditions listed below: a) One (1) Year Parts and Labor PLUS One (1) Additional Year Parts-Only Warranty: Toaster Elements (metal sheathed) Drawer Warmer Elements (metal sheathed) Drawer Warmer Drawer Rollers and Slides Food Warmer Elements (metal sheathed) Infra-Black® Elements (metal sheathed) Display Warmer Elements (metal sheathed air heating) Holding Cabinet Elements (metal sheathed air heating)
2. LIMITATION OF REMEDIES AND DAMAGES Hatco’s liability and Buyer’s exclusive remedy hereunder will be limited solely, at Hatco’s option, to repair or replacement by a Hatco-authorized service agency (other than where Buyer is located outside of the United States or Canada, in which case Hatco’s liability and Buyer’s exclusive remedy hereunder will be limited solely to replacement of part under warranty) with respect to any claim made within the applicable warranty period referred to above. Without limiting the generality of the foregoing, all portable Products (as defined in N.S.F. 4-4.28.4) shall be delivered by Buyer, at its sole expense, to the nearest Hatco-authorized service agency for replacement or repair. Hatco reserves the right to accept or reject any such claim in whole or in part. Hatco will not accept the return of any Product without prior written approval from Hatco, and all such approved returns shall be made at Buyer’s sole expense. HATCO WILL NOT BE LIABLE, UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS RESULTING FROM THE USE OF OR INABILITY TO USE THE PRODUCTS OR FROM THE PRODUCTS BEING INCORPORATED IN OR BECOMING A COMPONENT OF ANY OTHER PRODUCT OR GOODS.
b) One (1) Year Parts and Labor PLUS Four (4) Additional Years Parts-Only Warranty on pro-rated terms that Hatco will explain at Buyer’s Request: Powermite® Gas Booster Heater Tanks Mini Compact Tanks (stainless steel) 3CS and FR Tanks c) One (1) Year Parts and Labor PLUS Four (4) Additional Years Parts-Only Warranty PLUS Five (5) Year Parts-Only Warranty on pro-rated terms that Hatco will explain at Buyer’s Request: Booster Heater Tanks (Castone®) d) One (1) Year Parts-Only Warranty for components not installed by Hatco: Accessory Components (including but not limited to valves, gauges and remote switches)
Form No. GRCD/HDM-0703
20
NOTES
21
Form No. GRCD/HDM-0703
HATCO AUTHORIZED PARTS DISTRIBUTORS
ALABAMA
IOWA
NEW YORK (continued)
TEXAS
Jones McLeod Appl. Svc. Birmingham 205-251-0159
Electric Motor Service Co. Davenport 319-323-1823
Alpro Service Co. Brooklyn
Stove Parts Supply Fort Worth
ARIZONA
KENTUCKY
Auth. Comm. Food Equip. Phoenix 602-234-2443
GCS Service Louisville
Appliance Installation Buffalo 716-884-7425
Armstrong Repair Service Houston 713-666-7100
Byassee Equipment Co. Phoenix 602-252-0402
LOUISIANA
Northern Parts Dist. Plattsburgh
518-563-3200
Commercial Kitchen Repair Co. San Antonio 210-735-2811
J.B. Brady, Inc. Syracuse
315-422-9271
San Antonio Rest. Equip. San Antonio 210-532-1660
CALIFORNIA Industrial Electric Huntington Beach
714-379-7100
Chapman Appl. Service San Diego 619-298-7106 P & D Appliance S. San Francisco
650-635-1900
Chandlers Parts & Service Baton Rouge 225-272-6620 Bana Comm. Parts, Inc. Shreveport 318-631-6550 MARYLAND Electric Motor Service Baltimore 410-467-8080
COLORADO
GCS Service Silver Spring
Hawkins Commercial Appliance Englewood 303-781-5548
MASSACHUSETTS
DELAWARE
502-367-1788
301-585-7550
Ace Service Co., Inc. Needham 781-449-4220
718-386-2515
NORTH CAROLINA
UTAH
Authorized Appliance Charlotte 704-377-4501
GCS Service Salt Lake City
OHIO
VIRGINIA
Akron/Canton Comm. Svc. Inc. Akron 330-753-6635
Daubers Norfolk
757-855-4097
Certified Service Center Cincinnati 513-772-6600
Daubers Springfield
703-866-3600
GCS Service Columbus
WASHINGTON 614-476-3225
MICHIGAN
Electrical Appl. Repair Service Independence 216-459-8700
FLORIDA
Commercial Kitchen Service Bay City 517-893-4561
E. A. Wichman Co. Toledo
Whaley Foodservice Repair Jacksonville 904-725-7800
Bildons Appliance Service Detroit 248-478-3320
OKLAHOMA
Nass Service Co., Inc. Orlando 407-425-2681
Midwest Food Equip. Service Grandville 616-261-2000
B.G.S.I. Pompano Beach
MINNESOTA
Krueger, Inc. Oklahoma City
GCS Service Minneapolis
OREGON
Food Equipment Service Wilmington 302-996-9363
954-971-0456
Comm. Appliance Service Tampa 813-663-0313 GEORGIA Adcox Service Co. Atlanta
GCS Service Kansas City 404-361-8010
Southeastern Rest. Svc. Norcross 770-446-6177
612-546-4221
MISSOURI 816-920-5999
Commercial Kitchen Services St. Louis 314-890-0700
HAWAII
Kaemmerlen Parts & Service St. Louis 314-535-2222
Burney’s Comm. Service, Inc. Honolulu 808-848-1466
NEBRASKA
Food Equip Parts & Service Honolulu 808-847-4871 ILLINOIS Parts Town Lombard
402-341-1414
NEVADA Burney’s Commercial Las Vegas 702-736-0006
708-865-7278
Eichenauer Elec. Service Decatur 217-429-4229 Midwest Elec. Appl. Service Elmhurst 630-279-8000 Cone’s Repair Service Moline 309-797-5323 INDIANA GCS Service Indianapolis
Anderson Electric Omaha
317-545-9655
Hi. Tech Commercial Service N. Las Vegas 702-649-4616 NEW JERSEY
817-831-0381
419-385-9121
Hagar Rest. Service, Inc. Oklahoma City 405-235-2184
801-487-3653
Restaurant Appl. Service Seattle 206-524-8200 WISCONSIN A.S.C., Inc. Madison
608-246-3160
A.S.C., Inc. Milwaukee
414-543-6460
CANADA
405-528-8883
BRITISH COLUMBIA
Bressie Electric Co. Portland
503-231-7171
Ron’s Service, Inc. Portland
Key Food Equipment Service Vancouver 604-433-4484
503-624-0890
ONTARIO
PENNSYLVANIA FAST Comm. Appl. Service Philadelphia 215-288-4800
R.G. Henderson Ltd. Toronto
416-422-5580
Choquette CKS Ottawa
613-739-8458
GCS Service Pittsburgh
412-787-1970
QUÉBEC
K & D Service Co. Harrisburg
717-236-9039
Choquette CKS Montreal
514-722-2000
Elmer Schultz Services Philadelphia 215-627-5401
Choquette CKS Québec City
418-681-3944
Electric Repair Co. Reading
610-376-5444
RHODE ISLAND Marshall Electric Co. Providence 401-331-1163
Jay Hill Repair Fairfield
973-575-9145
SOUTH CAROLINA
Service Plus Flanders
973-691-6300
Whaley Foodservice Repair W. Columbia 803-791-4420
NEW YORK
TENNESSEE
Acme American Repairs, Inc. Brooklyn 718-456-6544
Camp Electric Memphis
901-527-7543
HATCO CORPORATION P.O. Box 340500, Milwaukee, WI 53234-0500 U.S.A. (800) 558-0607 (414) 671-6350 Parts & Service Fax (800) 690-2966 Int’l. Fax (414) 671-3976 www.hatcocorp.com Printed in U.S.A. July 2003
Part No. 07.04.275.00 Form No. GRCD/HDM-0703
