Transcript
OPERATION AND MAINTENANCE MANUAL MOBILE MODULAR SELF SERVICE MILK UNIT
MODEL: BMM-1000
GENERAL INFORMATION The BMM-1OOO series Self Serving Milk Units are equipped with refrigerated compartment to hold (12) 13" x 13" x 11" milk cases. UNPACKING: Examine the interior of the unit and make sure all packing materials, such as wood and cardboard removed before unit is plugged in to an outlet. Examine the exterior and interior of the unit to determine whether any damage was incurred during delivery. If so, notify the carrier or your dealer immediately to file a damage claim. All ATLAS equipment is carefully tested and inspected prior to shipment. When accepted for delivery by the carrier, the responsibility for safe arrival is assumed by the carrier. INSTALLING: These units have been carefully designed to meet your required operational needs: Prior to operating these units, it is important to check the following: 1. Supply cord and plug for possible damage due to shipping. (Loose wires, fraying, or cuts in cord.) 2. Temperature controls must not have any “play or movement with exception of control knob.” 3. Plug in to proper electrical receptacle as indicated on the rating plate of each unit . WARNING: SHOULD ANY DAMAGE BE FOUND AFTER GOING THROUGH THE ABOVE CHECK LIST, DO NOT ATTEMPT TO OPERATE UNIT. CALL YOUR DEALER IMMEDIATELY TO ARRANGE FOR FACTORY AUTHORIZED SERVICE. OPERATING: For equipment containing refrigeration units, allow adequate time after 'turn-on" for units to reach proper temperature. Time varies depending on ambient temperature and locations. The unit will maintain proper temperature, cycling on its pressure control, so field adjustment should not be necessary. MAINTENANCE: This equipment has been designed to require minimum maintenance and has been constructed to meet National Sanitation Foundation, Underwriters Laboratory Standards, and U.S. Public Health Service Standards. Non-toxic chemical cleaners or mild detergents are recommended for cleaning of fixtures. Do NOT use steel wools at any kind. Steel wool particles will work in to the grains of the metal causing corrosion. Also, these particles can cause a health hazard. Should scouring be required, use a non-abrasive type of cleaner. Do not use caustic solutions on your equipment. Hosing or steam cleaning should not be necessary to keep these fixtures clean and sanitary. Do not allow water or steam to come In contact with electrical components. WARNING: Be sure to disconnect power source before cleaning or servicing the unit. Liability for improper or careless use is the responsibility at the equipment owner or persons servicing the unit, including authorized service agents.
PARTS LIST ITEM NO.
DESCRIPTION
PART NO.
1
CONDENSING UNIT
2004-1
2
5” CASTER W/O BRAKE
1800-497
3
5” CASTER W/BRAKE
1800-499
4
LATCH, SASH. CHROME
1800-3870
5
SWITCH MAIN ON/OFF
1800-3955
6
COVER PLATE SWITCH
1800-4054
7
THERMOMETER CLIP-ON
4913-4
8
BOTTOM, FALSE
P40225-000
9
LOCK, FRONT DOOR
P41593-000
10
HINGE, LEFT LID
P42293-000
11
HINGE, RIGHT LID
P42294-000
12
HINGE, CENTER
P42295-000
13
LATCH, DOOR LOCK
P42760-000
14
BRACKET, TRAY SLIDE
70045-8
13
8
14
2
3
COMPRESSOR SCHEMATIC
TEMPERATURE CONTROL Should readjusting the temperature be necessary, turn the adjustment screw as illustrated below:
Adjust this screw only. Turn clockwise to achieve colder temperature. Turn counterclockwise to achieve warmer temperature. Turn approximately 1/4 turn for each degree of temperature change desired.
THIS CONTROL IS LOCATED IN THE COMPRESSOR COMPARTMENT
LIMITED WARRANTY Atlas Metal Industries, Inc. warrants to the Purchaser of this product that the same shall be free from defects in the workmanship and material for a period of one year from the date of original installation of the equipment, but not to exceed eighteen (18) months after date of shipment from factory. During this period of time Atlas Metal Industries, Inc. will replace all defective parts and will pay for authorized replacement labor. Replacement and installation of such parts and labor shall be provided only upon prior written authority of Atlas Metal Industries, Inc. The Refrigeration warranty is for a twenty (20) month time period and includes supplying the compressor at a no charge basis provided the damage to the compressor was not caused by the customer or end user. Authorized replacement labor will be paid for a period of one year from date of installation. Freight costs for defective unit to and from Atlas Metal Industries, Inc. are not included, and all defective parts must be returned to the factory freight prepaid for evaluation. ALL WARRANTY LABOR MUST BE AUTHORIZED BY ATLAS METAL INDUSTRIES, INC. PRIOR TO THE ACTUAL WORK BEING DONE. This warranty does not apply to any equipment or any part thereof, which has been subjected to shipping damage, improper voltage, alteration, abuse or misuses, and does not cover loss of food, other products, or damage to property due to mechanical or electrical malfunction. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEREOF. SELLER DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OF THE GOODS OR THE FITNESS OF THE GOODS FOR ANY PURPOSE AND BUYER AGREES THAT THE GOODS ARE SOLD “AS IS.”
WARRANTY INFORMATION In order to have your invoice approved for payment by the factory, please note the following: _______________________________________________ An authorization number must be obtained from the factory prior to performing any warranty service. _______________________________________________ Atlas Metal will not approve excessive labor due to poor access to the unit being serviced. If design does not allow reasonable access, contact the factory. _______________________________________________ All travel time that exceeds 100 miles round trip must be authorized by the factory. _____________________________________________________________________________________
Thank You: Warranty service Dept.
