Transcript
VIID2
OPERATION INSTRUCTION 4-wire high definition video intercom system
USB INTERFACE & SD CARD RECORD VIDEO & PHOTO VIID2_PM 8/1/14
FEATURES
DESCRIPTION OF LED INDICATORS Three LEDs are provided in the upper left corner of the unit. These LED are described below: When this LED is lit red, this indoor unit is connected to main power supply. When this LED is flashing red slowly, an intercom communication from this unit is occuring. If the LED is flashing red rapidly, the other indoor unit is being operated and functionality on this indoor unit is disabled.
If the LED is lit red, this indoor unit is communicating with the 1st outdoor camera.
If the LED is lit green, this indoor unit is communicating with the 2nd outdoor camera.
Name
Description
DESCRIPTION OF SYMBOLS
TFT display
View visitor image displayed on the TFT screen
Displays the real time image from the camera at entrance
Speaker
Sound from outdoor camera
Microphone
Transmit the voice to outdoor camera
1. 2. 1. 2.
Monitoring
Allow you to observe the real time image from the camera at the entrance.
Release the door lock
Call transfer
Transfer call to an extension monitor
Adjusts the display brightness
Talk
Start conversation with outdoor camera
Adjusts the chroma of the TFT display
Unlock
Unlock the door lock by pressing this button
Increases/decreases the Talk volume
Navigation-key
Operate in menu mode by pressing these buttons
Increases/decreases the ring tone volume
9
Brightness
Adjust the brightness of TFT display
The expansion slot for an SD card
10
Chroma
Adjust the chroma of TFT display
USB interface
11
Talk Volume
Adjust the Talk volume
12
Ring Volume
Adjust the ring volume
13
SD card slot
Expansion slot for additional SD card
14
USB interface
Download/upload media files including MP3, WAV, WMA, JPG via a USB data cable
1. Scroll up (menu mode available) 2.Manual video record(A3 on page12) 3. Photo browse in standby mode (C2 on page 15) Scroll down (menu mode available) The shortcut-key for video playback (standby mode available) Scroll left (menu mode available only) The shortcut-key for playing music (standby mode available) Scroll right (menu mode available only) The shortcut-key for setting the date & time (standby mode available) 1. Confirm the items (menu mode available) 2. Manual photo capture (A4 on page12) 3. Enable menu mode (standby mode available)
Call transfer to other indoor monitor Call out the deletion sub-menu (menu mode available) Activates conversation mode Exit and return to the previous menu.
SYSTEM DIAGRAM
LINE CONNECTION DIAGRAM PRIMARY MONITOR
2P short pin plugged
CAMERA
OUTDOOR CAMERA1
To Access Control Module “Request to Exit” terminals
External switching power supply
Dry contact
CAMERA
2P short pin pulled
To Access Control Module "Request to Exit" terminals
OUTDOOR CAMERA2 EXTENSION UNIT
External switching power supply
NOTES ON WIRING CONNECTIONS Electric lock: A camera is not include in the package. Purchase an electric lock that is most suitable for the location. Normally, the system supports locks with a Normally Open (N.O.) door unlocking method. This means that in the normal state, the dry contacts are open, so the lock is in a constant closed state. If a door unlock push-button the is pressed, and the dry contacts close and the the lock is released. The 2P Short Pin is designed for programming the indoor monitor. The indoor monitor will be programmed to main monitor if you plug in the 2P Short Pin; the indoor monitor will be programmed to extension monitor if the 2P Short Pin is is pulled out. When the machine detects acceptable power after startup, SETUP OK is shown. Otherwise, setup the machine to detect electric power source. Indoor machine is powered with a built-in power source. External powering is optional. Refer to actual power source. For machines using the built-in power, the input voltage can range from AC110V - 240V. Please disconnect the AC power plug before installing the device (see below).
For wire selection, refer to the following. (The type of wire used has a large effect on the system) 1.4C ordinary unshielded and shielded wire connection mode:
OPERATION INTRODUCTION VISITOR CALL
Standby mode The visitor press the call button on outdoor camera 1
The visitor press the call button on outdoor camera 2
A 10s continuous Ding Dong tone is played inside and outside The visitor s image is automatically displayed on the screen
NOTE: If the call buttons of two outdoor camera are pressed at approximate to the same time, preference is given to the outdoor camera whose call button was pressed first, unless the call button is pressed again after the indoor monitor goes into standby mode. There is no indication on the second outdoor camera.
Press the Talk button
Stop ringing NOTE: Start conversation with outdoor camera
The indoor unit will automatically go to standby mode if you are not at home or do not reach the indoor unit within 60 seconds.
The conversation duration is 120s at a time Press the unlock button on indoor monitor
Press the Talk button release the again door lock
End
Both the visitor's voice and image will not be switched off within 20s after the unlock button is pressed. This function allow you to make sure the visitor has enough time to enter. When the doorbell record for the video mode From the start of a call, the entire Process will be recorded. If you press recording will stop. When the doorbell record for the photo mode: The whole process will be captured; allows the user to manually press the key to capture an image, or press 2 for single manual capture. In monitoring the state: the machine can listen to the sound of the door machine, you can press button to call and press the button to open the lock. This allows the user to manually capture an image by pressing , or press the key for manual recording or to stop recording.
MONITORING
CALL TRANSFER TO ANOTHER EXTENSION
Connnection of 2 outdoor cameras to at least 1 indoor monitor is required for dual entrance monitoring.
At least 2 indoor units is required
Standby mode Press the monitoring button on indoor monitor
Display image from 1st outdoor camera on the screen.
Press the monitoring button on indoor monitor again
Display image from 2nd outdoor camera on the screen.
monitoring duration is up to 60s Press the Talk button
Press this button again to return to standby mode
Outdoor camera call indoor monitor and conversation is underway
Press this button to activate a call transfer to another extension.
NOTE: When you are transferring a call to other extension, the original conversation indoor unit will return to standby mode, the indoor unit which the call is being transferred to will also sound a continuous Ding Dong tone, and the video image will appear on its screen.
A continuous Ding Dong tone is played Press the Talk button on any indoor unit.
Start conversation with outdoor camera
NOTE: To release a door lock and end a conversation, please see VISITOR CALL on page 8. Start conversation with outdoor camera
Press the unlock button to release the door lock
INTERNAL COMMUNICATION AMONG INDOOR UNITS At least 2 indoor units are required.
Press the Talk button again
Standby mode End
NOTE: If you are using only one outdoor camera in monitoring mode, you can also end monitoring mode by pressing the monitoring button. Please note: If you are using two outdoor cameras and a blank display appears when you activate monitoring mode on an indoor unit, disconnect power from the indoor unit, then reappply power to it after 10 seconds. If you are using two indoor units, you can activate monitoring mode on the another indoor unit to display the same image on both screens. The image displayed on the screen depends on which outdoor unit is being activated from indoor unit, or which unit's monitoring button is pressed last. In monitoring mode, if a conversation with outdoor unit is underway and the visitor presses the call button on any outdoor unit, monitoring mode will be switched off. The visitor's image will appear on its screen and continuous ringing will occur. If you are using the indoor unit with a hands-free device, press the Talk button to reactivate the conversation with the visitor. For more detailed operations, please see VISITOR CALL on page 8. State monitoring,press to start Manual recording press to start Manual camera. In the standby mode,press to turn on/off the LCD backlight I and , view the recording. 7
Press the Talk button A continuous Ding Dong tone is played Press the Talk button on any of the indoor units
NOTE: In internal communication mode, if a visitor presses the call button on either of outdoor unit, the internal communication mode will be switched off. The just visitor' s image will appear on its screen and continuous ringing will be heard. You can press the Talk button to reactivate the conversation with the visitor. For more detailed operations, please see VISITOR CALL on page 8.
.
Start conversation among indoor units
Press the Talk button again
End
8
MENU OPERATIONS
C Memory device: press
NOTE As you know, the button on the front panel is dual-function including basic and extension function(marked as in the left picture). For the basic function, please refer to pages 8 - 10 for detailed operation. After you enter the menu mode, you can activate the extension function (see the icon and on page 4). For the navigation-key, please see the description on menu functions on the page 4.
and
key to view the information about the flash or SD card.
SD card
D
Default setting:Restore the factory default settings,press
NAME
to confirm, or press
to return.
DEFAULT
STANDBY MODE As shown in Figure 1 press the Menu key interface as shown below
to open the main menu interface. The main menu
In menu mode, you can press either of the Left /Right arrow keys to select RECORD MODE, SYSTEM SETTING, or MULTIMEDIA. If you need to confirm the just selected items, you can do that by pressing the Middle-key (see figure1). Pressing the button will exit the present menu and return to the previous menu.
Language
Time set
Language settings Press to save or return.
Time settings Press Press to save.
and
or
Memory
Default
to select a language, then press
to choose the date or time, then press
to select, then press
to be confirm.
again
A Door REC: Select the outdoor machine in the video mode or camera mode, factory default video mode.
B Note Sound Select are limited to the
ringtones or MP3 ringtones Note Video mode and internal calls ringtones
C No Bell settings Switching time can be set to No Bell,can be cross-day setup to select the time, Press to setup,press to save
After the date article highlighting,press key. Year runner highlighted,press and to choose,press and to setup month and year, after setting press to save, the same as time Setting;Standby can choose to display or turn off the display
D
CAM REC Can set a timer recording time,and can be cross-day setup.Press select the time,press to setup,press to save.
and
to
DESCRIPTION ON SD CARD USAGE
SD card expansion slot Professional SD card (e.g.kingston) recommended
On the right side of the indoor monitor, there is an SD card expansion slot. You can use a SD cards to store images taken by the camera. Maximum supported capacity for the SD card is 32GB.
Each folder has a corresponding video and pictures subfolder. Each file is stored separately. The latest File has the largest sequence number. Old and new files are arranged in order of size.
In stand bymode ,to insert the card, align it with the slot (golden contacts facing towards the user) and push the card fully into the device until it engages with a click. To remove the card push it briefly in to release, after which you can easily pull it out. No software action is needed to remove the card. 2. If you are not using SD card, all media files(video,photo,music)will be recorded onto the internal flash memory with 128MB maximum capacity.
3. After you insert an SD card, all media files will be recorded onto the SD card, and not the internal flash memory. Into the corresponding file,press to play the selected file. Press and in the player interface to adjust the volume.Press and to play the previous file or the next file. Press to eject the Delete menu option to delete a single file or all files, press to confirm the selection; Press to cancel the return
4. In the VIDEO PLAYBACK/PHOTO BROWSE/MUSIC PLAY mode, with the SD card inserted, you can only preview the media files stored on the SD card. To view media files stored on the internal flash memory (if any) please remove the SD card.
Delete single Delete all
Into the corresponding file,press to play the selected file, Press and in the player interface to adjust the volume,press and to play the previous or next file, press to eject. Use the Delete menu to delete a single file or all files, press to confirm the selection; press to cancel and return.
USB interface to connect a PC, requiring hours of standby display interface
12
In standby mode, a USB icon will be appeared on the screen if you connect indoor unit to the Personal Computer(shown as below) .If you connect the USB to the computer, and then to the machine power, the machine will enter the software upgrade, The mode display will not have any display , but you can upgrade the machine program through a dedicated PC software. If you do not upgrade process,The sequence will not damage the machine.
INSTALLATION PROCESS OF INDOOR UNITS
Double-click[ My Computer], and then you will find two additional devices [portable hard G] and [Portable Hard H]
Portable hard G
Portable Hard H
NOTE Avoid installation of the device near strong radiation e.g. TV set, video recorder and PC etc.
Double-click the [portable hard G] or [portable hard H] you will see the following four folders
Maintenance should be complied with a qualified technician. Avoid hard shake , beating and collision ,otherwise the internal exact components maybe be damaged . Select the most suitable position where the monitor is located at user's eye level. Switch off power supply before installing.
folder
Used to store the camera picture and video files (via computer backup or delete) keep more than 30cm away from AC power supply to avoid external interference. Keep it away from the water and magnetic field.
To install the indoor unit , please follow these steps as below: Used to store the camera picture and video files (via computer backup or delete)
Plastic anchors
Bracket
Used to store the camera picture and video files (via computer backup or delete)
13
14
Connection cable
SD card compatibility list
SPECIFICATIONS Display
7 inch TFT LCD(16:9)
Resolution
800 H X3(RGB)X480
Video system
PAL/NTSC
Intercom mode Conversation duration
Duplex communication
Standby status
200MA max
Working status
500MA max
120seconds
After the test, the following list of SD card compatible This model is recommended to use. If the list is not related to models, users can test compatible. Band name
Type
Capacity(GB)
Kingston
2
Kingston
16
Micro SD
use micro sd adapter
Kingston
32
Micro SD
use micro sd adapter
Operation temp.
Sandisk
64
Micro SD
use micro sd adapter
Installation
Surface mount
Sandisk
4
Micro SD
use micro sd adapter
Internal flash memory
To prevail in kind
Sandisk
2
Picture format
JPEG standard
External memory
SD card with 32GB max
Power supply
DC12V
Micro SD use micro sd adapter
SD
PACKING LIST
INDOOR MONITOR Indoor monitor Plastic anchor Installation screw Installation bracket 4P plastic conductor USB data cable TF card to SD card Operation instruction External switching power supply AC Power cord Please note that such external switching power supply marked by the Wireframe as above are not included if you select the indoor monitor which is internal switching power supply 15
16
