Preview only show first 10 pages with watermark. For full document please download

Operation Manual - Cascadia Video Products

   EMBED


Share

Transcript

DIGITAL VIDEO RECORDER PLE Series Server Operation Manual Please read these instructions and save this manual for future use www.cascadiadvrt.com / (888) 421-0050 1 SAFETY INSTRUCTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THIS PRODUCT HAS MULTIPLE-RATED VOLTAGES. ADJUST POWER INPUT SELECTOR SWITCH PROPERLY ON REAR OF UNIT BEFORE CONNECTING TO THE POWER SUPPLY. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not use near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the points where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense IMPORTANT The only way to disconnect power completely is to unplug the power cord Make sure at least one end of the power cord is within easy reach so that you can unplug the computer when you need to CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. www.cascadiadvrt.com / (888) 421-0050 2 Table of Contents 1. LAYOUT ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 5 FRONT VIEW ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 6 REAR VIEWㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 7 2. DISPLAY ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 8 ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 9 B A C K U P ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 9 ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 9 MAINTENANCE ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 9 ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 9 3. SETUP ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 10 ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 11 EVENT ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 12 ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 13 ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 14 CAMERA ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 14 MAINTENANCE ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 15 ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 16 CASCADE ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 17 4. QUICK USE 1 ㅡ ㅡ ㅡㅡ ㅡ ㅡㅡ ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 18 G E T T I N G S T A R T E D ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡㅡㅡㅡㅡㅡㅡㅡ 19 TIME & DATE ADJUSTMENT ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 20 DVR & REMOCON SETUP ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 21 HOW TO UPGRADE ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 22 ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡ ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 23 F O R C E R E C O R D I N G ㅡ ㅡ ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 24 SCHEDULE RECORDING ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 25 6. QUICK USE 3 ㅡ ㅡ ㅡㅡ ㅡ ㅡㅡ ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 26 QUICK PLAYBACK ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 27 NORMAL PLAYBACK ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 28 EVENT PLAYBACK ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 29 ALARM CASCADE SMART RECORD NETWORK USER STORAGE 5. QUICK USE 2 www.cascadiadvrt.com / (888) 421-0050 3 Table of Contents 7 . Q U I C K U S E 4 ㅡ ㅡ ㅡㅡ ㅡ ㅡㅡ ㅡ ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 30 STILL IAMGE SAVE ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 31 BACKUP ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 32 8 . Q U I C K U S E 5 ㅡ ㅡ ㅡㅡ ㅡ ㅡㅡ ㅡ ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 33 I P S E T T ING ㅡ ㅡ ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 34 DDNS SETTING/WEB VIEWER CONNECTING ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 35 E-MAIL SETTING & NOTIFICATOIN ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 36 USER P/W SETTING ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 37 9 . Q U I C K U S E 6 ㅡ ㅡ ㅡㅡ ㅡ ㅡㅡ ㅡ ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 38 PRESET & EVENT TRACKING ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 39 MOTION, SENSOR & ALARM SETTING ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 40 CONNECTING SENSOR ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 41 CONNECTING ALARM ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 42 CONNECTING PTZ ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 43 CONNECTING EXTERNAL STORAGE ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 44 INSTALLATION EXAMPLE 1 ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 45 INSTALLATION EXAMPLE 2 ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 46 10. CLIENT ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 47 INSTALLATION & CONONNECTION ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 48 11. CLIENT ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 50 SINGLE SEARCH ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 51 PTZ CONTROLㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 52 LIVE JPG, BMP, AVI SAVE ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 52 CMS P/W SETTING ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 53 CONFIG FILE SAVE/LOAD ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ 54 www.cascadiadvrt.com / (888) 421-0050 4 1. LAYOUT FRONT VIEW REAR VIEW www.cascadiadvrt.com / (888) 421-0050 5 FRONT VIEW 12 15 1 2 13 3 4 16 5 17 6 7 18 11 8 14 9 10 1. Display Button Shows the Display menu. 2. Search Button Go to the Search menu. 3. Setup Button Go to the Setup menu. 4. PTZ Button Pan / tilt a selected camera. 5. Zoom Button Zoom In/Out at 1CH Layout mode. 6. Backup Button Go to the Backup menu. 7. REC Button Record all cameras manually for emergency. 8. Rotate / Hold Button Rotates the Live Camera Display. Hold the search speed with Jog & Shuttle. 9. Lock Button Locks the DVR. 10. Playback Button Play, Pause, Reverse, Stop, End, Start. 11. Jog Dial Play recorded images frame by frame when this dial is rotated. 12. Shuttle Ring Play fast when this dial is rotated. 13. Direction / Camera Layout Button Move the cursor on the menu and shows camera Layout. UP: 1CH Layout, Right: 4CH Layout Down: 9CH Layout Left: 16CH Layout 14. Enter Button Determine the setting values. 15. ESC Button Go back to the previous status. 16. Power LED Light up when power is on. 17. HDD LED Light up when built-in HDD is working. 18. REC LED Light up when Manual recording is on. 19 22 21 20 19. Power Button 20. USB Port Plug USB memory stick Upgrade Software or Save Data. (USB 2.0) 21. Camera Button Choose a camera you want to see. 22. CD/DVD Eject Button www.cascadiadvrt.com / (888) 421-0050 6 REAR VIEW 1. Camera Input Connectors Connect cameras to these BNC connectors. 13. USB (1.1) Connect USB memory stick for Upgrade. 2. Camera Output Connectors (Loop Out) These BNC connectors supply video signals looped through the video input connectors. 14. LAN (10/100BASE-T) Connect this unit to a network compatible with 10BASET or 100BASE-Tx. 3. Quad1 Show quad out (Fixed, Rotation) and a slave DVR on an analogue monitor. 15. VGA Connect a VGA monitor with this connector. 4. Quad2 Show quad out on analogue monitor. (Fixed, Rotation) 5. Spot Rotate a camera on an analogue monitor in order. 6. Cascade In/Out (BNC) Connect with the CASCADE IN/OUT connector of another DVR for image transmission when using two or more units of DVR. 7. Audio Input Connectors (AUDIO IN 1 - 4) Input audio signal supplied from an external device such as a microphone amplifier. 8. IEEE1394 Connect to an external device like CD/DVD RW. 9. Audio Output Connector (AUDIO OUT) Connect a speak for audio out. 10. TV Connect a monitor to BNC connector. 12. S-VHS Connect a monitor to S-VHS connector. 16. RS232 (SERIAL) Connect a external device that supports this DSub 9-pin connector when controlling this unit. 17. PAL/NTSC Chooses a PAL/NTSC video signal. 18. PTZ Connect RS485 compatible combination cameras with these port. 19. Cascade In/Out (RJ-11) Connect with the cascade Out connector of another DVR for command signal when using two or more units of DVR. 20. RS422 Connect to Keypad. 21. ALARM IN Connect an external device such as a sensor or a door switch. 22. ALARM OUT Connect a control switch when controlling this unit using an external device, or when controlling an alarm device such as a buzzer or a lamp. www.cascadiadvrt.com / (888) 421-0050 7 2. DISPLAY ALARM BACKUP CASCADE MAINTENANCE SMART www.cascadiadvrt.com / (888) 421-0050 8 DISPLAY MENU 1. Press “DISPLAY”. The SETUP MENU will be displayed. Move the curser to highlight the “ALARM”, “BACKUP”, MAINTENANCE”, “SMART” or “CASCADE” Icon and press the “Enter” button to show the appropriate information. 4. DISPLAY / CASCADE Select the slave DVR that will show up on Master DVR. 5. DISPLAY / MAINTENANCE 2. DISPLAY / ALARM DVR ID = Set ID to communicate with Keyboard. Keypad ID = Set ID to communicate with DVR. Status Bar Top = Show the information bar upward. 3. DISPLAY / BACKUP 6. DISPLAY / SMART Turn On/Off alarm. Backup the recorded data with CD/DVD RW. Show HDD status. (Only information) www.cascadiadvrt.com / (888) 421-0050 9 3. SETUP RECORD EVENT NETWORK USER CAMERA MAINTENANCE STORAGE CASCADE www.cascadiadvrt.com / (888) 421-0050 10 SETUP - RECORD MENU 1. Press “SETUP”. The SETUP MENU will be displayed. 4. SETUP / RECORD / HOLIDAY Select a date to designate a holiday. 2. SETUP / RECORD / RECORD Size = Resolution, Fps – Recording speed Quality = Recording Quality Pre & Post Rec = Pre & Post Recording time NOTE: Item selection: Move the cursor using the arrow buttons. Change the setting: Press “Enter” button. Selecting a submenu: Select a submenu using buttons and press “Enter” button. NOTE: Default P/W is “1111111”. 3. SETUP / RECORD / SCHEDULE Set recording schedule for each camera. www.cascadiadvrt.com / (888) 421-0050 11 SETUP - EVENT MENU 1. Press “SETUP”. The SETUP MENU will be displayed. 2. SETUP / EVENT / MOTION Region = Motion set area Sensitivity = Motion sensitivity 4. SETUP / EVENT / ALARM Duration = Set alarm duration time. 5. SETUP / EVENT / ALARM SCHEDULE Set alarm schedule for each alarm. NOTE: Alarm goes off when alarm schedule is set. 3. SETUP / EVENT / SENSOR Type = Normal Close, Normal Open Preset = Link sensor with Preset function of Camera NOTE: Item selection: Move the cursor using the arrow buttons. Change the setting: Press “Enter” button. Selecting a submenu: Select a submenu using the buttons and press “Enter” button. NOTE: Default P/W is “1111111”. www.cascadiadvrt.com / (888) 421-0050 12 SETUP / NETWORK MENU 4. SETUP / NETWORK / DDNS DDNS Use = Support Dynamic IP. Domain Name = Type ID to use Dynamic IP. Use Local IP = Connect DVR in same local network like LAN for DDNS. Registry = Register the DDNS information. 1. Press “SETUP”. The SETUP MENU will be displayed. 5. SETUP / NETWORK / SERVER 2. SETUP / NETWORK / IP SET DVR Name = Show DVR name in network S/W. Max. Connect = Number of Live Connected Users Max. Search = Number of Live Connected Users Network IMG Size = Resolution for network transmission. Network Fps = Network transmission speed. Network Quality = Image quality for network transmission. 3. SETUP / NETWORK / EMAIL System Notify = Send email when DVR has problem. NOTE: Item selection: Move the cursor using the arrow buttons. Change the setting: Press “Enter” button. Selecting a submenu: Select a submenu using buttons and press “Enter” button. NOTE: Default P/W is “1111111”. www.cascadiadvrt.com / (888) 421-0050 13 SETUP / USER & CAMERA MENU 3. SETUP / CAMERA / CAMERA 1. Press “SETUP”. The SETUP MENU will be displayed. 2. SETUP / USER Permission = Give user access permission. Hidden = Show/Hide camera. Enable = Camera On/Off. PTZ = Camera Protocol. ID = Camera PTZ ID. 4. SETUP / CAMERA / COLOR Channel = Camera No. NOTE: Item selection: Move the cursor using the arrow buttons. Change the setting: Press “Enter” button. Selecting a submenu: Select a submenu using buttons and press “Enter” button. NOTE: Default P/W is “1111111”. www.cascadiadvrt.com / (888) 421-0050 14 SETUP / MAINTENANCE MENU 1. Press “SETUP”. The SETUP MENU will be displayed. 3. SETUP / MAINTENANCE / LOG Show DVR working status. 2. SETUP / MAINTENANCE / SYSTEM Transparency = Transparency of Menu Window. Flicker = Flicker filter for TV Out. Deinterlace = Anti aliasing Filter. NOTE: Item selection: Move the cursor using the arrow buttons. Change the setting: Press “Enter” button. Selecting a submenu: Select a submenu using buttons and press “Enter” button. NOTE: Default P/W is “1111111”. www.cascadiadvrt.com / (888) 421-0050 15 SETUP / STORAGE MENU 1. Press “SETUP”. The SETUP MENU will be displayed. 4. SETUP / STORAGE / IEEE1394 Show IEEE1394 device information. Format = Format media on backup use. 2. SETUP / STORAGE / IDE Show IDE device information. Format = Format media on backup use. NOTE: Item selection: Move the cursor using the arrow buttons. Change the setting: Press “Enter” button. Selecting a submenu: Select a submenu using buttons and press “Enter” button. NOTE: Default P/W is “1111111”. 3. SETUP / STORAGE / USB Show USB device information. Format = Format media on backup use. www.cascadiadvrt.com / (888) 421-0050 16 SETUP - CASCADE MENU 1. Press the SETUP button. The SETUP MENU will be displayed. NOTE: 2. SETUP / CASCADE / CASCADE Cascade Type = Set DVR as Master or Slave. VGA/TV Out = Show slave DVR to VGA/TV out. Quad1 = Show slave DVR to Quad1 out. Item selection: Move the cursor using the arrow buttons. Change the setting: Press “Enter” button. Selecting a submenu: Select a submenu using buttons and press “Enter” button. NOTE: Default P/W is “1111111”. www.cascadiadvrt.com / (888) 421-0050 17 4. QUICK USE 1 GETTING STARTED TIME & DATE ADJUSTMENT DVR & REMOCON ID SETUP HOW TO UPGRADE www.cascadiadvrt.com / (888) 421-0050 18 GETTING STARTED 1. Insert the “Power Plug” to an outlet 2. Turn the power button “ON”. Boot up Window will be displayed like the below. NOTE: Boot up window will only be displayed when on Factory default 3. Select “Language”, “GMT”, “Date/Time”. 4. Format the HDD. NOTE: Standard: Max. 4 HDDs will be available inside. CD/DVD (Option): Max. 2 HDDs will be available inside. 5. Go to Live mode. Show the “Loading……” and go to Live mode. www.cascadiadvrt.com / (888) 421-0050 19 TIME&DATE ADJUSTMENT It is recommended to check the clock before installation and put the clock right if it shows the wrong time. 4. Move the cursor to “Date & Time”. 1. Press “SETUP”. 5. Press “OK” button. The SETUP MENU will be displayed on the monitor. Change the GMT and then time & date. Press “OK” button to save the changed time. 6. Press “ESC” button to go back to LIVE mode. DVR will restart and the below warning window will show up. 2. Press “Setup” button again and No.1,2,3 and P/W window will show up. Input the P/W and A/S MENU will be displayed on the monitor. 7. Press “OK” button. Press “OK” to adopt the changed time and Backup window will show up. NOTE: The above warning message is to confirm the changed time. Select “OK” to confirm the time. Select “Cancel” to ignore the changed time. 8. Press “ESC” button to exit without Backup. Press “ESC” button to exit without Backup when Backup window shows up. And then the Live image will be displayed and the Selected time & date will be applied on the information bar. www.cascadiadvrt.com / (888) 421-0050 20 DVR & REMOTE CONTROLLER ID SETUP ID Setting of DVR Set remote controller ID as described below. ID Setting of Remote Controller Set remote controller ID as described below. 1. Face controller to IR receiver of DVR. 1. Press “DISPLAY”. The DISPLAY MENU will be displayed. 2. Holding the “ID” button of the remote controller. Power LED will twinkle. 3. Press No. of controller ID you set on DVR. 2. Go to DISPLAY / MAINTENANCE Select a Remocon ID No. 4. Press “Enter” button. Power LED will stop twinkle. NOTE: 3. Press “ESC” button to save and exit. When “Remocon ID” of DVR matches the remote controller ID, the LED on the front of the POWER stops twinkling. www.cascadiadvrt.com / (888) 421-0050 21 HOW TO UPGRADE Please perform the following instructions. 3. Plug in USB memory stick with UPGRADE file to DVR. 4. Go to “UPGRADE”. Upgrade window will show up. 1. Press “SETUP”. The SETUP MENU will be displayed on the monitor. 5. Press “Upgrade” button. DVR will restart and go to live mode. NOTE: If DVR hangs at the screen of “LOADING…” for 10 minutes after upgrade, please contact your local distributor. 2. Press “Setup” button again and No.1,2,3 and P/W window will be show up. Input the P/W and A/S MENU will be displayed on the monitor. www.cascadiadvrt.com / (888) 421-0050 22 5. QUICK USE 2 FORCE RECORDING SCHEDULE RECORDING www.cascadiadvrt.com / (888) 421-0050 23 MANUAL RECORDING 1. Start “Manual Recording”. Press the “REC” button to start manual recording. The indicator of REC will light and recording will start. Images from all the connected cameras will be recorded manually with the current recording rate. NOTE: When manual recording is performed, schedule recording will not be performed until manual recording stops. 2. Stop “Manual Recording”. Press the “REC” button again to stop recording. The indicator on the button will go off and recording will stop. Images from all the connected cameras will be recorded with the scheduled recording rate as schedule. www.cascadiadvrt.com / (888) 421-0050 24 SCHEDULE RECORDING Do the followings to do schedule recording. NOTE: Item selection: Move the cursor using the arrow buttons. Change the setting: Press “Enter” button. Selecting a submenu: Select a submenu using buttons and press “Enter” button. 3. Move to “SCHEDULE” and Press “Enter” button. The SCHEDULE MENU will be displayed. 1. Press “SETUP”. The SETUP MENU will be displayed on the monitor. How to set schedule 1.Choose CH (Camera) 2.Move the cursor on the time table 3.Press “No.” for Record like the following. 1 – None, 2 – NORMAL, 3 – MOTION, 4 – SENSOR, 5 – MOTION+SENSOR 4.Press “ESC” to change the CH (Camera) 2. Move the cursor to “RECORD” and Press “Enter” button. The RECORD MENU will be displayed on the monitor. SIZE = Resolution FPS = Recording rate Quality = Image Quality PRE = Pre-Record POST = Post - Record 4. Press “ESC” button again to “Save & Exit”. The Live image will be displayed and recording status will be displayed as circle on the right corner of each camera. www.cascadiadvrt.com / (888) 421-0050 25 6. QUICK USE 3 QUICK PLAYBACK NORMAL PLAYBCK EVENT SEARCH www.cascadiadvrt.com / (888) 421-0050 26 QUICK SEARCH It is possible to play recorded image without stopping recording. Playback image will be displayed on the monitor. 1. Press “Playback” button. Go to search mode directly. NOTE: It shows same camera layout of Display mode. To change the camera layout, press a direction button for 1CH, 4CH, 9CH, 16CH. 1CH – UP button 4CH – RIGHT button 9CH – DOWN button 16CH – LEFT button www.cascadiadvrt.com / (888) 421-0050 27 NORMAL SEARCH There are two ways to go to search mode and play it. - one is Normal Search. - the other is Event Search. 3. Move the cursor to Date and Press “Enter” button. Data map will be displayed for 24 hours. NOTE: Date with recorded data will be marked in yellow. 1. Press “SEARCH”. The SEARCH menu will be displayed on the monitor. 4. Select the start time and Press “Enter” button. Playback image will be displayed. 2. Press the CALENDAR button. The CALENDAR will be displayed on the monitor. NOTE: How to move the time indicator. Use the arrow buttons and jog dial. How to change the screen layout. Press Direction buttons of1-4-9-16 CH screen layout. NOTE: It could take a few minutes to bring out the recorded data according to HDD capacity. www.cascadiadvrt.com / (888) 421-0050 28 EVENT SEARCH There are two ways to go to search mode and play it. - one is Quick Search. - the other is Normal Search. 3. Select “Start” & “End” time. 1. Press “SEARCH”. The SEARCH menu will be displayed on the monitor. 2. Press the EVENT button. The EVENT menu will be displayed on the monitor. NOTE: EVENT search will help user to search recorded data as recording type and cam no. 4. Select “Recording Type” & “Cam No.”. 5. Select the list and Press “Enter” button. Playback image will be displayed. Playback image will be displayed on the monitor. NOTE: Please press “Lock” button to hide the backup window while doing backup process. www.cascadiadvrt.com / (888) 421-0050 29 7. QUICK USE 4 STILL IMAGE SAVE BACKUP www.cascadiadvrt.com / (888) 421-0050 30 STILL IMAGE SAVE PNG file save is only available at 1 CH screen layout at search. 1. Plug in USB memory stick to DVR. 5. Select 1CH screen layout. 2. Press “SEARCH”. The selected CH will be displayed on the monitor. The SEARCH menu will be displayed on the monitor. 6. Press “BACKUP” button. 3. Press the CALENDAR button. Save the still image as PNG file format. The CALENDAR will be displayed on the monitor. 4. Go to Playback Mode of Search. www.cascadiadvrt.com / (888) 421-0050 31 BACKUP To copy recorded images to the CD-RW or DVD disk, formatting (initializing) the disk is required in advance. 1. Press “Backup”. The BACKUP MENU will be displayed. 4. Set “Start” & “End” time and Press “REFRESH” button. DATA will be shown on the DB list. 5. Press “START” button Show backup progressing window. 2. Move the cursor to Backup Media and Press “Enter’ button. Select Backup device like CD-RW, DVD. NOTE: For external Backup media, it supports IEEE1394 not USB 2.0. 3. Move the cursor to “FORMAT” and Press “Enter” button. During formatting, the status window will be displayed. The status window will be closed automatically when completing formatting. NOTE: All data on the disk will be deleted if formatted (initialized). It is impossible to recover the deleted images on CD/DVD media. www.cascadiadvrt.com / (888) 421-0050 32 8. QUICK USE 5 IP SETTING DDNS SETTING/WEB VIEWER CONNECTING E-MAIL SETTING & NOTIFICATION USER P/W SETTING www.cascadiadvrt.com / (888) 421-0050 33 IP SETTING DHCP 1. Press “SETUP” . The SETUP MENU will be displayed on the monitor. Select YES or NO whether or not to use the DHCP server. When obtaining IP addresses, Subnet mask, and a Gateway address from the DHCP server, set to YES. If not, se to NO and enter those addresses manually. YES: Uses DHCP server. (LAN) NO: Uses Static IP address. NOTE: Pleas ask your network manager when you are not sure of DHCP or IP address. NOTE: Item selection: Move the cursor using the arrow buttons. Change the setting: Press “Enter” button. Selecting a submenu: Select a submenu using buttons and press “Enter” button. 2. Go to “NETWORK”. The IP SETTING MENU will be displayed on the monitor. NOTE: Default P/W is “1111111”. 3. Set “DHCP” to “Yes” for LAN use or Set “DHCP” to “No” for static IP use. Type the network information. www.cascadiadvrt.com / (888) 421-0050 34 DDNS & WEBVIEWER CONNECTING Perform the following basic network settings. 1. Press “SETUP”. :8080 The SETUP MENU will be displayed on the monitor. 2. Go to “Network” / “DDNS” The DDNS MENU will be displayed on the monitor. If the registered domain name is “home”, please type like the below example. Ex) http://home.pledvr.com:8080 DDNS IP DDNS IP is the default Server IP for DDNS. DDNS Port Show the Port No. in DDNS. Use Local IP Set “Use Local IP” to “YES” when try to connect DVR using DDNS in the same local network like LAN. NOTE: DVR is using 9090, TCP Port and 9100, UDP Port as default. How to register DDNS ID on DDNS server. 1. Enable “DDNS USE” to “YES” 2. Type the Domain name. 3. Press “REGISTRY” button to register the domain name on DDNS Server. How to use web viewer with Internet Explorer. 1. Run “Internet Explorer”. 2. Type the registered domain name of DDNS. Refer to the below example figure. 3. Select “User ID” and Input “P/W”. 4. Click “Connect” button. www.cascadiadvrt.com / (888) 421-0050 35 E-MAIL SETTING & NOTIFICATION NOTE: First the E-Mail setting should be done to send System Warning and DVR Start. 1. Press “SETUP”. The SETUP MENU will be displayed. NOTE: Item selection: Move the cursor using the arrow buttons. Change the setting: Press “Enter” button. Selecting a submenu: Select a submenu using buttons and press “Enter” button. NOTE: Default P/W is “1111111”. 2. Go to “Network” / “E-Mail”. The E-Mail MENU will be displayed. E-MAIL Address Enter the e-mail address for transmission. (System warning) SMTP SERVER Enter SMTP mail sever name. SMTP ID Enter the ID when SMTP sever requires. SMTP Password Enter the P/W when SMTP sever requires. System Notify Select ON or OFF whether or not to use the system notification. www.cascadiadvrt.com / (888) 421-0050 36 USER PASSWORD SETTING Perform the following settings. 1. Press the SETUP button. The SETUP MENU will be displayed on the monitor. NOTE: Set USER Password, Permission and Hidden camera. Each user can select camera to be hidden on live and search mode. NOTE: Default P/W is “1111111”. 2. Go to “USER”. The USER MENU will be displayed on the monitor. 3. Set P/W, Permission, Hidden camera per user. www.cascadiadvrt.com / (888) 421-0050 37 9. QUICK USE 6 PRESET & SENSOR TRACKING MOTION, SENSOR & ALARM SETTING CONNECTING SENSOR CONNECTING ALARM CONNECTIONG PTZ ADDING EXTERNAL STORAGE www.cascadiadvrt.com / (888) 421-0050 38 PRESET SETTING & SENSOR TRACKING 1. Press the “SETUP” & “CAMERA”. The CAMERA MENU will be displayed and choose a camera protocol. Set Save the camera movement as Preset. Move Move the selected Preset No. Clear Delete the selected Preset No. Tour Start Start all Preset No. in order with the Duration time. 6. Select “Preset No.” and Press “SET” button. Save the camera movement as the selected Preset No. NOTE: Max. Preset No. will be up to No.12. 8. Go to SETUP / EVENT / SENSOR. 2. Go back to Live Mode and choose a camera for PTZ. The SENSOR MENU will be displayed. 3. Press PTZ button. The PTZ MENU will be displayed. 9. Move the cursor to “Preset” and Enable to “YES”. Select preset No. for each camera. 10. Select camera and Preset No. 4. Press “Pan/Tilt” and the following menu will be displayed. Move, Zoom, Focus, Iris, Auto Pan, Light, Speed, OSD Menu 5. Press “Setup” and move the camera with the direction button. Press “ESC” button to exit the Pan/Tilt mode. NOTE: Sensor Tracking is only available on SENSOR. www.cascadiadvrt.com / (888) 421-0050 39 MOTION, SENSOR & ALARM SETTING 1. Press “SETUP”. The SETUP MENU will be displayed. 5. Move the cursor to “ALARM” and Press “Enter” button. The ALARM SELECTION will be displayed and select Alarm for the sensor of Camera. 6. Go to EVENT / ALARM Select a alarm type. (N/C, N/O) 2. Go to EVENT / MOTION Set a motion detecting area. 7. Move the cursor to “DURATION” and select duration time. Select alarm type (N/C, N/O) and select alarm duration time. 8. Go to EVENT / A.SCHEDULE ALARM MENU will be displayed. 3. Move the cursor to “ALARM” and select Alarm No. 9. Set the Schedule for each Alarm. Select alarm schedule for each alarm. The ALARM SELECTION will be displayed and select Alarm No. for the Motion of Camera. 4. Go to EVENT / SENSOR Select a sensor type. (N/C, N/O) NOTE: Press “ESC” button to select other alarm No. after setting alarm schedule. Make sure that alarm schedule is set for alarm. www.cascadiadvrt.com / (888) 421-0050 40 CONNECTING SENSOR How to Insert/remove wires For inserting into or removing wires from the TERMINAL BLOCK, push the lever as shown in the figure. Specification 1. Press “SETUP”. The SETUP MENU will be displayed. Input Circuits No. : 16 TTL level compatible input Input Type : N/C, N/O Sensor : Dry contact sensor Connection : Connect the stripped wires to the terminal block. Valid Input Pulse Duration : MIN. 500ms. Output Currents : Typical DC6mA. The sensor input has the specifications and normal operating conditions as described below. 2. Go to EVENT / SENSOR The SENSOR MENU will be displayed. How to connect Sensor Input For connection of sensor inputs S1 ~ S16, see the figure below. The figure below is an example of dry contact sensor connection. + 2. Move the cursor to “TYPE” and Select “N/C or N/O”. - SENSOR NOTE: Wiring Terminating Wires The wires for the TERMINAL BLOCK are terminated as described below. Strip the outer covering to the defined length (8~10mm). Suitable wires are AWG 20 ~ 26. www.cascadiadvrt.com / (888) 421-0050 41 Exterior Power CONNECTING ALARM (RELAY OUT) 1. Press the SETUP button. The SETUP MENU will be displayed. The alarm output has the specifications and normal operating conditions as described below. Specification Output Circuits No. : Automatic output of 4(8) relays. Output Method : Dry contact Connection : Connect the stripped wires to the terminal block. DC : 24V DC, 1.25A, 30W 125V DC, 0.24A, 30W AC : 125V AC, 0.5A, 62.5VA 250V AC, 0.25A, 62.5VA 2. Go to EVENT / ALARM The ALARM MENU will be displayed. 3. Move the cursor to “TYPE” and Select “N/C” OR “N/O”. NOTE: For connection of R1 ~ R4(8) outputs, see the figure below. The figure below is an example for connecting the warning lamp. Exterior Power ALARM Wiring Terminating Wires The wires for the TERMINAL BLOCK are terminated as described below. Strip the outer covering to the defined length (8~10mm). Suitable wires are AWG 20 ~ 26. www.cascadiadvrt.com / (888) 421-0050 42 CONNECTING PTZ 1. PTZ Connection with DVR. Please refer to the below figure. PTZ D+ DPAN/TILT (1) R X + R X - T X + PAN/TILT (2) T X - R X + T X - R X + PAN/TILT (3) R X + R X - T X + R X - T X + T X - PAN/TILT (4) R X - T X + www.cascadiadvrt.com / (888) 421-0050 43 T X - EXTERNAL STORAGE CONNECTING 1. Connecting EHD1500 to DVR EHD1500 HDD Capacity Tera1500A is connected to the IEEE1394 port on the DVR. Please set up as follows. 6HDDs(500GB*6) – 3TB NOTE: Power ON and OFF DVR and thenEHD1500 like the below order. IEEE1394 Port of DVR Power ON: EHD1500 to DVR. Power OFF: DVR to EHD1500. There are two IEEE1394 ports at the rear of EHD1500. One is for connection to DVR (Port IN), the other for expansion (Port Out). Rear View of EHD1500 Connect the EHD1500 Port IN to the IEEE1394 port of DVR, using an IEEE1394 cable as above. Cable Connection with EHD1500 www.cascadiadvrt.com / (888) 421-0050 44 INSTALLATION EXAMPLE 1 INSTALLATION EXAMPLE 1 The below is the basic installation with Tera1500A and Keyboard. www.cascadiadvrt.com / (888) 421-0050 45 INSTALLATION EXAMPLE 2 INSTALLATION EXAMPLE 2 The below is advanced installation with 5 DVRs and Keyboard. www.cascadiadvrt.com / (888) 421-0050 46 10. CLIENT INSTALLATION CONNECTION www.cascadiadvrt.com / (888) 421-0050 47 CLIENT INSTALLATION / CONNECTION 1. Client S/W Installation. Remote surveillance, search, setup are available through network connection. 5. Client Surveillance. CMS surveillance mode will be displayed. 2. Installation Minimum Requirement. - Celeron 1.0GHz or above 256MB Memory 24Bit true color or above 10/100 LAN Card O/S (Windows 2000, XP) 3. Program Installation. After setting the system minimum requirement, insert the program CD and run “CMS Setup” file to install client program. 6. DVR Registration on Client S/W. 1- Click “System Menu” button. 2- Click “CMS Configuration” button. 4. Run “CMS” program. “CMS” icon will appear on the window screen when the installation is finished. - System Menu - CMS Configuration 3- Select “User ID” and input “P/W”. Default P/W is “0”. 4- CMS CONFIG SETUP will show up. 5. CMS Log In. Select “User ID” and input default P/W, “0”. 5- Click “ADD SERVER” button. www.cascadiadvrt.com / (888) 421-0050 48 CLIENT INSTALLATION / CONNECTION 6- “REGISTER DVR” menu will show up. 11. Right-Mouse Click the DVR and select “CONNECT” for client connection. 12. Drag and Drop the DVR to Viewing window. 7. Input “Site Name”, “IP Address”, “User ID” and “P/W”. NOTE: “Service Denied” message means that all possible connections are used now. 8. Click “SAVE” button. 9. Go back to Surveillance mode. 10. Show a registered DVR list. www.cascadiadvrt.com / (888) 421-0050 49 11. CLIENT SINGLE SEARCH PTZ CONTROL LIVE JPG, BMP, AVI SAVE CMS P/W SETTING CONFIG FILE SAVE/LOAD www.cascadiadvrt.com / (888) 421-0050 50 SINGLE SEARCH 1. Select one channel. Select one channel at viewing window. (Green) 4. AVI Save Click “AVI” button. AVI Backup window will appear. 2. Click “Single Search” or Right-Mouse click on the camera. The window below will pop up and select “Single Search”. 5. JPG, BMP Save Click “CAPTURE” button. IMAGE Backup window will appear. 3. Select “Date & Time” and playback. The below window will pop up and select “Single Search”. NOTE: “Service Denied” message means that all possible connections are used now for search. So please disconnect the other channel and try “Single Search” again. www.cascadiadvrt.com / (888) 421-0050 51 SINGLE LIVE/PTZ CONTROL 1. Single Live / PTZ CONTROL. Select one channel on the viewing window. 4. AVI Save for Live Image. Click “AVI” button. AVI Backup window will appear. 2. Click “Single Live” or Right-Mouse click on the camera. The below window will pop up and select “Single Live”. 5. JPG, BMP Save for Live Image. Click “CAPTURE” button. IMAGE Backup window will appear. 3. PTZ Control. PTZ control is available. NOTE: DVR allows to connect Max.30CH for Client Connection. “Service Denied” message means that all possible connections are used now. www.cascadiadvrt.com / (888) 421-0050 52 SETTING CMS PASSWORD 1. Setting CMS Password. NOTE: Administrator = Surveillance, Search, Setup. Power = Surveillance, Search Guest = Surveillance 4- Select “User” and Input password. Default P/W is “0”. 1- Click “System Menu” button. 2- Click “CMS Configuration” button. - System Menu - CMS Configuration 3- Click “Setting Password button. www.cascadiadvrt.com / (888) 421-0050 53 CONFIG FILE IMPORT / EXPORT 1. Configuration file Import/Export. 1- Click “System Menu” button. 2- Click “CMS Configuration” button. - System Menu - CMS Configuration 3- Click “Import Config” or “Export Config” button. 4- Windows Explorer will appear 5- Save or Load the configuration file of CMS. www.cascadiadvrt.com / (888) 421-0050 54 SPECIFICATION * Data subject to change without notice. www.cascadiadvrt.com / (888) 421-0050 55 WARRANTY MODEL SERIAL NO. DATE OF PURCHASE WARRANTY PERIOD ONE YEAR FROM DATE OF PURCHASE PLACE OF PURCHASE 1. The following warranty service applies to all factory defects that occur during normal use of this equipment. 1) Within One Year of Purchase: Free Repair. 2. Warranty services are provided in accordance to the cause of damage as described below Service Cause of Damage Factory defect during normal use Within Warranty Period After Warranty Period Free Repair User misuse, misapplication or accidents Unauthorized alterations and repair service Unavoidable situations such as fire and earthquake Repair Service Charge Apply User abuse or tempering Natural wear of minor parts 3. For any product related service, contact the office. Keep this certification in a safe place with the manual. www.cascadiadvrt.com / (888) 421-0050 56 Repair Service Charge Apply DIGITAL VIDEO RECORDER PLE Series Server Operation Manual www.cascadiadvrt.com / (888) 421-0050 57