Transcript
OPERATION MANUAL
SUPERFAX Paper Folder PF-330/340 & PF370/380
Read this Operation Manual before using the machine. Keep the Operation Manual with care in a fixed storage place so that it may be available whenever required.
SUPERFAX GORPORATION Tokyo
- Japan
2012t09t12
Safety lnstructions Definition of Symbols and Notes ln this manual following names and signs stand for possible dangers. Danoer
This Symbol stands for immediate danger threatening the life and health of persons. Disregarding these instructions may cause severe damage to health
Caution
This symbol stands for an endangering situation that may occur. Disregarding these instructions may lead to slight injuries or damage to property.
Note
This symbol stands for notes, operational hints and other useful information. They are convenient for exploiting the machine's functional abilities.
Danger Make sure that the machine is electrically grounded. This prevents an electric shock when there is a leak of electricity. Use the machine at a proper supply voltage. A fire may start or the machine may bleak down if a higher or lower voltage other than the one printed on the machine is used, or if an electric current with a frequency that is not within the range of 50 to 60H2. Do not place any object on this machine. A fire may start or electricity may leak if water or a foreign object enters inside the machine. Handle the power cord with care. A fire may start or an electric shock may be caused if the cord is dambged, broken, or processed, if a heavy object is placed on the iord, or if the cord is bent forcibly.
Do not pull the power source plug out of or put it in the electric outlet using a wet hand. Otherwise, an electric shock may be caused. Do not remove the cover of this machine. Otherwise, an electric shock or injury may be caused.
Do not remodel this machine. Otherwise, a fire may break out or an electric shock may be caused.
lf the machine is used when it is in an abnormal condition, such as generating heat, emitting
smoke, and giving out a strange smell, a fire may break out or an electric shock may be caused. Turn off the power switch immediately and then pull the power plug out of the electric outlet. Afterward, consult with your sales agency.
lf abnormalities such as the power cord generating heat and giving out a strange smell are found, tum off the power swiich immediately and then pull the power plug out of the electric outlet. Aftenrvard, consult your sales agency. lf a foreign object enters into th€ machine, turn off the power switch first and then pul{ the power plug out of the electric outlet. Afterward, consult your sales agency. lf thunder approaches, pull the power cord out of the electric outlet to prevent a fire or breakdown caused by the falling of a thunderbolt.
Caution Do not let hairs, a necktie, or necklace hang above the drive of the machine. Doing so may cause an injury. Do not put the machine on an unstable place such as a shaky stand and a slant floor. Doing so may cause the machine to drop or fall down, causing an injury. Do not put the machine in a moist or dusty place Doing so may start a fire or cause an electric shock.
Be sure to pull out the power cord while holding the plug. lf the power plug is pulled out while holding the cord, a fire may break out or an electric shock may be caused. Be sure to pull the power plug out of the electric outlet first when moving this machine. Otherwise, the.cord may be damaged, causing a fire or an electric shock. Be sure to pull the power plug out of the electric outlet for safety purposes when this machine is not used for consecutive holidays or for other reasons.
lntroduction Thank you very much for purchasing SUPERFAX Paper Folder PF-300 series. This machine enables users to achieve greater efficiency in clerical work by releasing them from paper-folding work that has manually been performed in the past. Please read this Operation Manual carefully before using this machine.
Contents
(2)
Designation and functions of operation panel
(3)
Parts Names
(4)
(5)
Preparations............. 1. lnstallation of the folding plates 2. Preparation of paper feed tray.. 3. Adjustment of paper feed pressure ........... 4. Selecting the paper size and folding type......... 5. Preparation of paper eject roller 6. Test folding 7. Start folding function papers)
General explanation on System 1 . Standard mode (For standard size 2. Self-defined mode (For non-standard size 3. Fine adjustment under standard 4. Fine adjustment under self-defined 5. Cross Fold
.
(6)
papers) ..
mode mode
...................7 ............... .T ..................7 ............... g ........ g ............... g
...............9
........9 ...................10 ............. 10 ................. .10 .................... 11
...............12
......
12
Digital display function
(7)
13
Maintenance............
(8)
Routine
(9)
Trouble-shooting Guide
....13 14
-3-
(1) Specifications The PF-3301340 & PF-370/380 is designed to make automatic foldng for the following paper sizes and fold types without conducting the adjustments of folding positions depending on the different paper sizes and fold types. PF-330/PF-340 Paper
Fold
sizes
:
types :
A4 (297x210mm), AS Q1Ax148.5mm), Letter (279x216mm) and Legal (356x216mm) Single fold; Double fold; Fold out fold; Letterfold;Accordion fold; Gate fold
PF-370/PF-380 Paper
sizes
:
A3 (297x420mm), Ledger (17
Fold
types :
x
M (297x210mm),
A5 (210x148mm)
11"), Legal (14x8.5") and Letter (11x8.5")
Single fold; Double fold; Fold out fold; Letter fold; Accordion fold; Gate fold PF-330
Models
PF-340
PF-370 I
PF-380
Paper Size
100 x 130mm to 297 x 420mm
Paper weight:
45 to 135s/m2 (135q1m2 cannot be doubl+folded) Rough paper, Bond, Duplicating paper, Medium-quality paper, Recycled
Paper quality:
oaDer. Drawino oaoer Fold tvoes:
Single fold; Double fold; Fold out fold; Letter fold;Accordion fold; Gate fold
Paperfeed system:
Three-roller friction feed svstem
Maximum caoacitv:
500 sheets $4koftrt of hioh-qualitv paper) 2,4OO to 6,000 sheets per hour 2,400 to 7,200 sheets per hour (sinole fold usino 44 size oaoer) (sinole fold usino A3 size oaper) Automatic setting by a built-in microcomputer Manual adiustment for other papersizes
Folding speed:
Controlsystem: Additional functions:
*
Skew conection device
* Paperjam detector
Power consumption: Power source: Dimensions:
Netweisht:
* Four-diqit addition counter 75W 114-127 VAC, 50/60 Hz or 22G240 VAC, 50/50H2 920 x 490 x 525mm (during use) 790 x 490 x 535mm (during use) 600 x 490 x 535mm (Stowed) 600 x 490 x 535mm (Stc'wed)
32 kq
(2) Designation and Functions of Operation Panel Cursor ke y
keyLE FT Ilrlt :. * {
/ ''""
{
6
S
':
d
is
play
Start
Stop
J Pictu
\
&
elf -def in ed
Digital display
P
\
,.ar. a....-:..,.-:i
Standard
U
p( spr
Set
\ Cursor keY Curs or l( ey DOWN
re
1
Reset
RIGH-tT
Standard & self-deffinle,d display lor PF-3701IPIF- 38 Name
Fu ncti on
Show number of folded sheets, total number, and fine adjusting
Dlgital display
mode. When the folding number is zero(0), press "Reset" button and total folding number shall be displayed twice. First (E.g.,. 1st indication "0012" and 2nd indication "3456" means total number. is 123,456.) Decrease the speed, while the indicator moves right-ward.
Reset
Speed
"-
Speed "+'' Start Stop
Cursor key LEFT Cursor key RIGHT Cursor key UP Cursor key DOWN
"SET'button Speed "+" & Speed
Cursor keys left right Error indicator
1
Error indicalor 2 Error indicator 3 Error indicator 4
&
lncrease the speed, while the indicator moves left-ward The machine starts working in case of no malfunction. The machine Stop worl(ing or Memory f or fine adjustment mode Move the lndicator leftward, or decrease the displayed digit number, or move paper stopper toward the starting point. Move the lndicator rightward or increase digit num ber, or move paper stopper plate away from the start point lndicator move up, or exit from self-defined mode, or acijust ihe first folding on the upper folding plate. lndicator move down, or exit from self-define mode, or adjust the second folding on the Iower folding plate. Press to test fold 1 sheet of paper after the paper size and folding modes chos en are set automatically. Press these two buttons simultaneously to enter fine adjusting mode, and "nP-'1 " is shown in the digital display. Refer to section 3 for more instruction on this function. Press these two buttons simultaneously, the digital display will show a number, and the machine enters the self-defined mode. Refer to section 3 for more instruction. No paper on paper feed tray or paper feeding lever is not pressed
down. The upper folding plate is noi instailed properly. The lower fotding ptate is not installed properly.
No paper is delivered out to the paper receiving tray or paper jam.
5-
(3) Parts Names
CI @ @ @
o @
Pictu re
€)
2
@
@ @ @ @)
Pictu re
3
(o Name
Number
Name
Number
O
Paper guide
@
Paper support lift
@
Paper feed roller
@
Controlpanel
o
Paper feed table
@
Roller cover
@
Auxiliary paper feed tray
@
Upper folding plate
o
Paper eject table
@
Fine adjustment knob
@
Paper stack extension
G)
Socket for Upper/Lower folding plates
@
Paper eject roller
@
@
Table Up Lever
G)
Coaxial cable for UPPer Plate Coaxial cable for Lower Plate
o
Front cover
@
@
Power switch
@
-6-
lnlet (Behind Lower Plate) Lower folding plate
(4) Preparations 1. lnstallation of the folding plates: First, put both upper and lower folding plates in place and lock them firmly. (Picture 4) lnsert the connector on coaxial cable into the plug located on the inner wall of the rear cover (Picture 5, 6 & 7) and fasten the screw. Pictu re 4 Connector
Pictu re
5
Lock
Pl uq
Pictu re
Picture
6
7
2. Preparation of Paper Feed Tray:
lf standard paper size is used, there is a scale on the auxiliary paper feed tray. Align the paper with the scale (Picture 8) and fit the paper guides to the papbr width (Picture 9) and tighten the knurled screw (Picture 10).
Picture
8
t'lCtuure re
Iv
PiCtu
re
1
0
lf non-standard paper is used, put the paper on the center and fit the paper guides to the paper width then tighten the knurled screw.
-7-
3. Adjustment
of paper feed pressure:
lf
paper quantity is small, adjust the paper feed pressure using paper support lift. Pull it up and then move right to increase the pressure. Pull it up and then move left to decrease the pressure. (Picture 11)
Pictu re
11
4. Selecting the paper size and folding type: When the power switch is turned on, the baffles on the upper/lower folding plates will move to the "A4 Single fold" or "Letter Single fold" position automatically. lf you are going to use any other paper size and fold type, follow the instructions below. For the standard paper sizes and fold types, which are preset in the memory, select the proper position for the paper size and the fold type on the self-defined display by pressing any of the 4 cursor keys.
Note: The preset paper sizes are; PF-330/340- A4 (297x21 0mm), A5 (210x148.Smm), Letter (279x21 6mm) and Legal (356x216mm) P'F-3701380-A3 (297x42Amm), A4 (297x21 Omm), A5 (21 0x148mm) Ledger (17 x 11"), Legal (14x8.5") and Letter (11x8.5") I
Firstly, enter into "self-de,fined nnode". (Page 1 0) Then, choose one self-defined area (I-Iv), then press the SET key. The upper and lower folding plates will enter a self-defined position. After that, enter into "Fine adjustment under Setf-defined mode". (Page 12) Note: The adjusted position can be memorized. (See the details on Page 11)
-8-
5. Preparation of Paper Eject Roller Regulate the slide plate position according to the paper specification and the fold type so that the paper is properly ejected. Refer to the table on the next page.
Slide plate
Pictu re
i2
PF-330/340 i'-, ,1,
F,,lt, i ri.: li 1ri _
L
E B E B
.-
LTR
L(;L
E}
E
o
tr
..t, tl;
l
Lg-r
B
tr
I.q-tlcr F.,l'l
i.tlr ir
,4*-*.'
rit.t
.\
l-. ,l tI
tr
B
B
a
:
E
E
!.
i< tl r lt,
li,
tfi
[ ], itlI r11 l;,
rl, I
.,j i -t3
'1, I
;#J.i
B B E E
B B
I
0
PF-370/380 Folding
Singie iro 1d
Fold-out
Letter F'old
Gate
Accordi
cnr
Double Fold
Fold
type
A3 A4
j
A5
LTR LGL LGR
E
tr
B E
tr tr
E
a
tr tr tr tr
o
l:, tr
a
tr
tr
B @
E B
tr
E
i
tr tr
E E E E @ E tr _-6 E
E i13, tr
i i
I
I I
_-,1
Note: ln order to eject papers more quickly, lift the two rollers up position.
-9-
6. Test folding
:
When the LED on the self-defined display area is lit at the proper position for
the paper size and the fold type, press the central sET key to test fold
1
sheet of paper.
It tfie paper is not fo,lded cotrectty, adjust the fo{ding p{ate positions
in standard "Fine adjustment under accordance with the instructions on page 11 mode". "Fine self-defined under page adjustment 12 mode" or
7. Start folding
:
Wtren t{re test fotding is properly done, press the START { Fold type
Single f old L ./\ 1---'i
\.I \/ Size A too long Size A too short
Doubl e f
Letter fold
Fold-out
old A
d\ \')p|-a
Accordi on f old
Gate
A
\
Press left key to
Press left key to
Press left key to
Press left key to
Press left key to
to adjust
adj ust
adj ust
adj ust
adj ust
adj ust
Press left key to adi ust
Press
Pres s
right key to adiust
right key to adiust
Press right key to
Press right key to adi ust
Press right key to ad i ust.
PTeSS
right
key
adi ust
S
Fold type
ingle old
f
Letter f old
Fold-out
Double f old
Accordion f old
Gate
B
Size B too long Size B too short
Note
Press lef t key to adj ust
Press left key to
Press left key to
adj ust
adj ust
Press ght key to adi ust
Press right key to adj ust
Press right key to
ri
adj ust
Press left key to
Press left key to adjust.
Press lef t key to adjust.
adj ust
Press right key to adj ust
Press right key to adj ust
Press right key to adj ust
:
ln single fold, the lower folding stopper should be in the top position.
(8) Routine Maintenance 1.
Cover the machine properly to keep it away from dust when the machine is not in use.
2. Clean the enclosure,
roller and cushion with alcohol or wet soft cloth from
time to time.
3.
Use an alcohol detergent when cleaning the cover. Never use other kinds of detergent which inciudes corrosive agent to avoid defacing of the plastic cover or erasing the characters printed on the cover. - 14'
(9) Trouble-shooting Guide 1
Faults Paper Feed tray empty with LED "1" on
2
3
4
5
6
7
8
o
No Paper feeding with LED "4" on
Cause
No paper or less paper the paper feed tray
1. 2.
on
Paper jam Paper jam sensor dirtied or broken
Solution Add more paper for folding
1. Clear the jam paper. 2. Clean the senor or contact
local dealer for after-service. 1. Paper feed rollers are 1. Clean the surface with soft dirty. cloth with alcohol. 2. Paper is too slippery. 2. Select proper paper. Paper 3. The driving V-belt slips. 3. Adjust the V-belt with the feeding slips 4. Paper feed rollers are strain pulley. worn or torn. 4. Replace the worn and torn parts. 5. The one-way clutch of the synchro-wheel has failed 5. Replace the synchrowheel oarts. There are paper particles Paper jam Clean up the paper particles. in the paper path. 2 Paper is too thin. 2 Select proper paper. 3 Folding plates are not 3 lnstall folding plates mounted correctly. correctly. The counting sensor has Contact local dealer for a problem. after-service support. Folded paper 1. There are paper particles l.Clean up paper particles or wrin kles. on the roller. other stain on the roller. 2. Roller pressure too high. 2.Adjust roller pressure. 3.Paper is not proper. 3.Select Drooer Daoer. Paper not Paper out pulley is not in Readjust the position of ejected after correct position paper out pulley. foldinq. Paper jams 1. Outlet roller position l.Adjust the roller in right halfway or incorrect. place. speed is too 2.Paper particles in the 2.Clean counter sensor low sheet counter sensor (paper jam sensor). (paper iam sensor). No display 1. The fuse is gone. Contact local dealer for power when 2. Power supply failure. after-service su pport. is turned on. Paper feed The mounting screws of the Tighten the electromagnet speed is not electromagnet are loose. screws. stable.
10
E0onLED
Machine error
Contact local dealer for after-service suooort.
-15-
