Ot/or Discontinued Model - M

Transcript

Plug-in Signal Conditioners M-UNIT OPTICAL TRANSMITTER/RECEIVER MODEL OT/OR MODEL & SUFFIX CODE SELECTION OT–❑–❑ TRANSMITTER MODEL INPUT Voltage Current 1 : 0 – 10mV DC A : 4 – 20mA DC 2 : 0 – 100mV DC A1: 4 – 20mA DC* 3 : 0 – 1V DC B : 2 – 10mA DC 4 : 0 – 10V DC C : 1 – 5mA DC 5 : 0 – 5V DC D : 0 – 20mA DC 6 : 1 – 5V DC E : 0 – 16mA DC 4W : -10 – +10V DC F : 0 – 10mA DC 0 : Specify voltage G : 0 – 1mA DC H : 10 – 50mA DC Z : Specify current *50Ω input resistance for Code A1 POWER INPUT AC Power DC Power B : 100V AC G : 200V AC S : 12V DC C : 110V AC H : 220V AC R : 24V DC D : 115V AC J : 240V AC F : 120V AC OR–❑–❑ RECEIVER MODEL OUTPUT Voltage Current 1 : 0 – 10mV DC A : 4 – 20mA DC 2 : 0 – 100mV DC B : 2 – 10mA DC 3 : 0 – 1V DC C : 1 – 5mA DC 4 : 0 – 10V DC D : 0 – 20mA DC 5 : 0 – 5V DC E : 0 – 16mA DC 6 : 1 – 5V DC F : 0 – 10mA DC 4W : -10 – +10V DC G : 0 – 1mA DC 0 : Specify voltage Z : Specify current POWER INPUT AC Power DC Power B : 100V AC G : 200V AC S : 12V DC C : 110V AC H : 220V AC R : 24V DC D : 115V AC J : 240V AC F : 120V AC DISCONTINUED MODEL Replaced with Model OT2/OR2 Functions & Features • Isolation up to several hundred thoudsand volts with a fiber optics cable • High-density mounting Typical Applications • Ion implanter • Electron-beam devices • Dust chamber • Protection against inductive noises in power substations RELATED PRODUCTS •Fiber optics cable: 10 meters (model: AMPCP-10M) 20 meters (model: AMPCP-20M) 30 meters (model: AMPCP-30M) GENERAL SPECIFICATIONS Construction: plug-in Connection I/O: M3.5 screw terminals Transmission cables: connector Housing material: flame-resistant resin (black) Isolation OT: input to power OR: output to power Overrange output: approx. -10 – +120% at 1 – 5V Front adjustments: zero and span; ±5% Transmission method: light pulse (100 – 500 Hz) Maximum transmission distance: 30 meters (98 ft) ORDERING INFORMATION Specify code number and variables. •Transmitter code number (e.g. OT-6-B) •Receiver code number (e.g. OR-A-B) •Special input and output ranges (For codes Z & 0) P. 1 / 3 ES-1317 Rev.4 OT / OR INPUT to the OT UNIT ■DC CURRENT: shunt resistor attached to input terminals (0.5W) Input resistance: For resistance values other than listed below, specify when ordering. Input Input Resistance 4 – 20mA : 250 (Ω) (50Ω for Code A1) 2 – 10mA : 500 1 – 5mA : 1000 0 – 20mA : 50 0 – 16mA : 62.5 0 – 10mA : 100 0 – 1mA : 1000 10 – 50mA : 100 ■DC VOLTAGE: -300 – +300V DC Minimum span: 10mV Zero suppression/elevation: max. 1.5 times span Input resistance Input Span Input Resistance 10 – 100mV : 10k (Ω minimum) 0.1 – 1V : 100k ≥1V : 1M INSTALLATION Power input AC: rating ±10%, 50/60 ±2 Hz, approx. 2VA DC: rating ±10% (ripple 10% p-p max.) approx. 2W (80mA at 24V) Operating temperature: -5 to +60°C (23 to 140°F) Operating humidity: 30 to 90% RH (non-condensing) Mounting: surface or DIN rail Dimensions: W50×H80×D123 mm (1.97"×3.15"×4.84") Weight: 400 g (0.88 lbs) PERFORMANCE in percentage of span Accuracy: ±0.3%* Temp. coefficient: ±0.015%/°C (±0.008%/°F) Response time: ≤0.6 seconds (0 – 90%)* Line voltage effect: ±0.1% over voltage range Insulation resistance: ≥100MΩ with 500V DC Dielectric strength: 2000V AC @1 minute (OT: input to power to ground) (OR: output to power to ground) *Overall performance with the combined OT and OR OUTPUT from the OR UNIT ■DC CURRENT: 0 – 20mA DC Minimum span: 1mA Zero suppression/elevation: max. 1.5 times span Load resistance: output drive 15V maximum Output Load Resistance 4 – 20mA : 750 (Ω maximum) 2 – 10mA : 1500 1 – 5mA : 3000 0 – 20mA : 750 0 – 16mA : 900 0 – 10mA : 1500 0 – 1mA : 15k ■DC VOLTAGE: -10 – +12V DC Minimum span: 5mV Zero suppression/elevation: max. 1.5 times span Load resistance: output drive 10mA maximum; 5mA for negative voltage output; at ≥0.5V Output Load Resistance 0 – 10mV : 10k (Ω minimum) 0 – 100mV : 100k 0 – 1V : 100 0 – 10V : 1000 0 – 5V : 500 1 – 5V : 500 -10 – +10V : 2000 Specifications subject to change without notice. P. 2 / 3 ES-1317 Rev.4 SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Z + INPUT R – * Low Drift Amplifier 3 S 1 3 2 4 Volt. / Freq. Converter Z Waveform Shaper FIBER OPTICS Freq. / Volt. Converter S Output Driver 1 + OUTPUT 2 – 4 7 U(+) 5 5 7 U(+) 6 8 V(–) POWER POWER 8 V(–) 6 Base Socket Base Socket *Input shunt resistor attached for current input. EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENT mm (inch) ■DIMENSIONS CLAMP (top & bottom) 20 (.79) 7.8 (.31) 35.4 (1.39) 80 (3.15) 25R min. 50 (1.97) min.) 103 (4.06) 123 (4.84) 5 4 3 7 8 1 2 2–4.5 (.18) dia. MTG HOLE 15 (.59) deep 8–M3.5 SCREW 50 (1.97) 6 80 (3.15) DIN RAIL 35mm wide 40 (1.57) [3.3 (.13)] 50 (1.97) •When mounting, no extra space is needed between units. ■TERMINAL ASSIGNMENT 6 5 4 3 7 8 1 2 12 (.47) INPUT RESISTOR (model: REM) Input shunt resistor attached for current input. P. 3 / 3 ES-1317 Rev.4