Transcript
Overview Appliance Diagram
⌘ System Overview ●Front Hardware
●Operation ➢
Source & Target port
●Operation ➢
Erasing Port
➢
PC-Link Port
§ Log Report ●
Advanced Function Clear ALL Log
After user entering password, the log report saved in duplicator can be wiped out.
[ Advanced Function ]
●
1. Clear ALL Log
Users can reset password to protect log records. To execute function "7.4.1", you must use password. The default password is "123456".
[ Advanced Function ] 2.Setup Password ↓ [ New Password ] == >
▲ ▼
Setup Password keys to input
How to Erase HDD Data Secure Erase The international authorized high standard Secure Erase function. It overwrites every single track on the hard drive with "00". Even HPA/DCO or other data area which are not able to load, can be erased all together.
[ Erase ] 5. Secure Erase ↓ Secure Erase
HDD Link to PC & Write-Protect Output read-only log to PC.
※ How to Use PC-Link 1) Firstly, connect one end of USB3.0 cable to USB port of PC. Connector the other side of the cable to PC port of the duplicator. (USB3.0-Link to PC)
2) Select function table “7. HDD Link To PC” and click “OK” to enter PC-Link mode. FR100 HDD Duplicator 7.HDD LinkTo PC
3) The new added areas of HDD will appear on Disk Drives folder after connecting to PC and entering function 7.
On the right-bottom corner of PC screen, it will pop out USB device installed status.
4) On PC, it cannot do several tasks on the write-protected HDD, such as formation, adding new files, deleting files or even changing the content.
The new added files are shown as write-protected so that the task to copy being rejected.
Move the cursor on the selected folders. Press the right tab of the mouse. On the selection list, the item / cannot be found.
When change the content of the file, it cannot be saved to this location.
5) Press “ESC” key to exit the function. Press “ESC” to cancel the task. The screen will show the dialogue for confirming again, “Are you sure” to exit.
PC-Link ↓
Are You Sure? Press “OK” key again. The system screen will exit back to function 7. HDD Duplicator 7.HDD LinkTo PC
Function Table 17 FR100 Function
Items/Description Copy source HDD to target HDDs. Refer to function "6.1 Copy Area" for different copy modes
1. Copy
selection.
2. Compare
Compare data bit-by-bit between source and copied targets.
3. Copy+Compare
Auto copy and then compare copied targets with source HDD to ensure data correctness. 4.1 Quick Erase Erase HDD’s index table only, it takes short time to execute this function. 4.2 Full Erase Erase the whole HDD content.
4. Erase
4.3 DoD Erase (DoD5220.22-M E) Erase HDDs three times complying with USA Department of Defense (DoD) standard. 4.4 DoD EraseComp (DoD5220.22-M E) Erase whole HDDs 3 times and bit-by-bit to check if data is completely erased. 4.5 Secure Erase (NIST800-88) Erase unreachable or hidden areas (HPA/DCO) all together with
this mode.
5.1 Show HDD Info. Show HDD’s basic information such as HDD model name and capacity. 5.2.1 Update BIOS Update the system firmware via one BIOS HDD.
5. Utility
5.2 Update System
5.2.2 Create Update HDD Format one HDD to quickly save firmware in the HDD.
5.3 System Info. Show information of the duplicator system, including controller model number and software version. 6.1.1 System and Files Set to copy source HDD's data area only. 6.1.2 ALL Partitions Set to copy partitions areas of the source. 6.1 Copy Area
6.1.3 Whole HDD Set to copy the whole source HDD.
6. Setup
6.1.4 Percentage(%) Set to copy the percentage range of the source HDD. 6.2 Skip Error Set to ignore error of source HDD while copying. (0 -65535, Unlimited) 6.3 Language Select preferred language. (English/Japanese)
Copy Unknown Copy unknown area when the device cannot identify the 6.4.1 Unknown
format.
Format
Skip Unknown Skip copy unknown area when the device cannot identify the format. ONE Byte
6.4 Advanced Setup
A random character to be written into every byte. 6.4.2 Erase Pattern
Big Random Data A set of random character to be written into a set of area.
6.4.3 Wait HDD Time Auto start time after plugging HDD from 0~30 seconds. 6.4.4 Stop Motor Time Auto running time after stopping motor from 1~20 seconds. 6.5 Restore Default Reset back to original manufacturer setting.
7. HDD Link To PC Output read-only log to PC.
Specification 17 FR100 / FR218 Name
FR series: Forensic Read-Only Lock/Backup HDD Duplication
Model
FR100
Targets/Port
1:1
Model
FR218
Targets/Port
1:2
Copy Speed
7.2GB/min
PC-Link Speed
15GB/min
PC-Link Interface
USB3.0 Log out
Operation Type
Stand-alone operation
PC-monitoring Interface
▼
Source Read-only: Log report text files written-in lock ▲
Advanced Function
PC-Link: Real-time PC monitoring via USB port Real-time PC monitoring; Log report management Direct support: 1.8"/2.5"/3.5" SATA HDD/SSD HDD compatible: All major HDDs brands, SATA interface HDD/SSD
Display
Backlight monochrome LCD display
Status LED
LED (Red/Green/Yellow) on each slot; Red(fail), Green(pass), Red(fail)
Keys
4 push keys (
Copy Function vs Formats
/ UP,
/ Down, OK/ confirm/enter, ESC/exit/cancel)
Quick Copy (System & Files): support FAT16/32/64, NTFS, Linux (EXT2/ EXT3/ EXT4), Mac (HFS+/ HFX/ HFS), GPT, Dynamic All Partitions/ Whole HDD/ Percentage Copy: support all formats
Write Blocked
Source port read-only supported
Bad-Sector
Skip bad sector copy by self-setting tolerance
Compare
High speed bit-by-bit data comparison
Erase
Quick Erase, Full Erase, DoD Erase (DoD5220.22-M E), Secure Erase (NIST800-88)
Capacity
15TB above
Power
Input: adjustable voltage 100V~240V, 50/60Hz; Output: 12V, 5A
Temperature
Working temperature: 5°C ~ 45°C; Storage temperature: -20°C ~ 85°C
Humidity
Working humidity: 20% ~ 80%; Storage humidity: 5% ~ 95%
Certification
FCC, CE, RoHS
