Owner`s Guide - Directechs.com

Transcript

Model: CHRSALL RS-CHLED & RS-CHLCD Rev.: 20091218 2-Way LED & LCD Remote Start Kits Owner’s Guide The RS-CHLED and RS-CHLCD kits each offer a complete remote start solution including a 2-way LED or LCD transmitter/receiver and an all-in-one mobile integration module. RS-CHLED RS-CHLCD Index RS-CHLED Understanding the RS-623 Remote................................................................................ 02 Using the RS-623 Remote............................................................................................... 02 Listing the Available Commands..................................................................................... 03 RS-CHLCD Understanding the RSS-5224 Remote............................................................................ Using the RSS-5224 Remote.......................................................................................... Out of Range............................................................................................................... Replacing the Battery.................................................................................................. Programming the Remote Control Features................................................................ Using your 1-Way Remote Control.............................................................................. Using your 2-Way Remote Control.............................................................................. Understanding the Confirmations Emitted by the 2-Way Remote............................... Upon Entering your Vehicle......................................................................................... 04 05 05 05 06 06 07 07 09 Cold Weather Start Feature............................................................................................. 09 Warranty.......................................................................................................................... 10 TECHNICAL SUPPORT / INFORMATION web resources: www.xpresskit.com www.xpressvip.com www.directechs.com © 2009 Directed Electronics. All rights Model: CHRSALL RS-CHLED & RS-CHLCD Rev.: 20091218 2-Way LED & LCD Remote Start Kits Page 2 RS-CHLED 2-way LED remote start kit with up to 1,500’ of range.* The Astrostart RS-CHLED kit is a complete remote start solution, which includes a 2-way LED transmitter/receiver and an all-in-one mobile integration module. In the kit, you will find: § 1x 623-RX (Antenna). § 1x 623-TX (2-way transmitter). § 1x RF Interconnect Cable. § 1x CHALL Chrysler Interface. § 1x Xpress Start Plug-In Remote Start. § 1x CHTH1 T-Harness. * Range based on line of sight, unobstructed testing in ideal conditions. Actual range will vary due to local conditions including but not limited to environment, terrain, physical obstructions, vehicle location and orientation, interference and other possible impediments. Understanding the RS-623 Remote Affordable 2-way communication with 1500 feet range*, Simple LED read out for confirmation of command and True confirmation of start via transmitter. The system can learn up to a maximum of 4 transmitters. Any transmitters can be stored in more than 1 memory slot. When a 5th transmitter is learned the 1st remote is erased (FIFO). Using the RS-623 Remote To ensure that commands are transmitted properly, press the desired button for 2 seconds. A command will not be executed if you do not press the button long enough. The indicator light will flash while transmitting the command. The remote included in your kit may differ from the one illustrated. © 2009 Directed Electronics. All rights Model: CHRSALL RS-CHLED & RS-CHLCD Rev.: 20091218 2-Way LED & LCD Remote Start Kits Page 3 Listing the Available Commands Button Function Lock the doors and arm the factory alarm. Unlock the doors and disarm the factory alarm. Open the trunk. + Panic ON: press the LOCK button and hold it for at least 4 seconds. Panic OFF: press the UNLOCK button. Start the vehicle. Stop the vehicle (hold button for at least 4 seconds). Set car to idle mode when it is already running. + Cold Weather Start feature (see page 9 for more information). + Open and close the sliding door (driver side). Only accessible with Chrysler Town & Country 2008-2010, Dodge Grand Caravan 2008-2010, and Volkswagen Routan 2009-2010. The remote transmits a visual confirmation by means of an LED. Immediately following a transmission, the LED will flash (single blink) green if the command was successfully received by the system or red if the command was not received. In the case of a start command, the LED provides a first confirmation to acknowledge the command reception by the system then, a second confirmation is sent to indicate if the starting was successful or not. © 2009 Directed Electronics. All rights Model: CHRSALL RS-CHLED & RS-CHLCD Rev.: 20091218 2-Way LED & LCD Remote Start Kits Page 4 RS-CHLCD 2-way LCD remote start kit with up to 5,000’ of range.* The Astrostart RS-CHLCD kit is a complete remote start solution, which includes a 2-way LCD transmitter/receiver and an all-in-one mobile integration module. In the kit, you will find: § 1x 5224-RX (Antenna). § 1x 5224-TX (2-way transmitter). § 1x 5224-TXC (1-way companion transmitter). § 1x RF Interconnect Cable. § 1x CHALL Chrysler Interface. § 1x Xpress Start Plug-In Remote Start. § 1x CHTH1 T-Harness. * Range based on line of sight, unobstructed testing in ideal conditions. Actual range will vary due to local conditions including but not limited to environment, terrain, physical obstructions, vehicle location and orientation, interference and other possible impediments. Understanding the RSS-5224 Remote The RSS-5224 is the ultimate 2-way communication 4-button transmitter. It supports multiple channels and vehicles, while providing a vehicle status indicator and command confirmations with graphics, as well as audio tones. A maximum of four remote controls can be assigned to your vehicle. See your dealer for additional remote controls. The range of your remote control can be affected by a weak battery, interference from nearby metal structures, hydro poles, or crowded parking lots. If the vehicle is out of range, the transmitter will emit a soft chirp after 3 seconds to indicate that the command has not been received by neither the module nor the transmitter. The system can learn up to a maximum of 4 transmitters. Any transmitters can be stored in more than 1 memory slot. When a 5th transmitter is learned the 1st remote is erased (FIFO). © 2009 Directed Electronics. All rights Model: CHRSALL RS-CHLED & RS-CHLCD Rev.: 20091218 2-Way LED & LCD Remote Start Kits Page 5 Using the RSS-5224 Remote To send a command, press the corresponding button for two seconds. The command may not be sent if the button is not pressed long enough. The remote control beeps when a button is pressed, then emits eight short beeps during the transmission, i.e. about one second after the button was pressed. Your remote control can transmit on four different channels, allowing control of four separate vehicles. Only the “Panic” command is transmitted on ALL channels simultaneously. To select a different channel, press the “P” button located on the back and hold it for 2 seconds, when the button is released the transmitter passes to the next channel. The remote control shown may differ from the ones included in the kits. Your system may be programmed in such a way that it can distinguish between two groups of remote controls (maximum: two remotes per group). These groups let you activate predefined settings (seat, mirror and other) when unlocking certain vehicles (additional optional equipment required). This feature is available with certain firware only. As soon as a command is sent, the remote switches over to standby mode in order to receive and display confirmations sent by the command module installed in the vehicle. These confirmations are sent to all the programmed remote. These signals are transmitted only once and could be neutralized by radio or electromagnetic interferences generated by electronic devices in the vicinity. If no confirmation is received in a given location, move away from electronic devices and activate the "Status” command. The start module will inform you of the status of door locks, alarm (only if the Factory Alarm Trigger Monitoring feature is supported by the firmware), and running of the engine. Note that the communication between the vehicle and the transmitter operates in only one direction at a time. This is why it is recommended to wait for the confirmation before sending another command. Otherwise, the vehicle and the transmitter could transmit at the same time wich would block the command as well as the returned confirmation. Out of Range If the vehicle is out of range, the transmitter will emit a soft chirp after 3 seconds to indicate that the command has not been received by neither the module nor the transmitter. Replacing the Battery The LCD of the 4-button remote has a battery icon telling you when to replace the battery. We strongly recommend keeping a replacement battery in your glove compartment. The remote controls require one AAA battery. See your dealer for spare batteries. To replace the battery, slide the latch sideways and remove the battery cover on the back of the remote control case, remove old battery and replace it with a new one. Make sure the battery is placed the right way (see pictogram inside the cover). © 2009 Directed Electronics. All rights Model: CHRSALL RS-CHLED & RS-CHLCD Rev.: 20091218 2-Way LED & LCD Remote Start Kits Page 6 Programming the Remote Control Features Note that the 1-way transmitter is automatically programmed. To access the 2-way remote control programming mode, press the “P” button located on the back of the remote and hold it for 5 seconds. The remote beeps once to indicate entering programming mode. Parameters Settings Keyboard un/lock Lock Button Display/Remarks / 1 BEEP / 2 BEEPS Unlock Mute Status confirmations Back light Number of vehicles Enabled 1 BEEP Disabled 2 BEEPS Enabled / 1 BEEP Disabled / 2 BEEPS Upon "Status" command Upon any command The display lights up for 3 seconds. Never The back light shuts off. 1234 1 - 4 (Default setting: 2) Legend: DISPLAYED ICON (BLACK); MASKED ICON (GRAY); DEFAULT SETTING (BLUE). Refer to the vehicle user manual for more information on confirmations emitted by your vehicle (i.e. the horn and parking lights). These confirmations are different for each vehicle, depending on which module/firmware is used. Using your 1-Way Remote Control Function Button Lock the doors and arm the factory alarm. * Unlock the doors and disarm the factory alarm. * ö Open the trunk (hold button for at least 4 seconds). Panic ON (hold button for at least 4 seconds). Panic OFF Start the vehicle. Stop the vehicle. Ö + Set car to idle mode when it is already running. Open and close the sliding door (driver side). ** Open and close the sliding door (passenger side). ** Cold Weather Start feature (see page 9 for more information). Remote Valet feature. + + + + © 2009 Directed Electronics. All rights Model: CHRSALL RS-CHLED & RS-CHLCD Rev.: 20091218 2-Way LED & LCD Remote Start Kits Page 7 Using your 2-Way Remote Control Confirmations Function Button Sent by Rem ote Control Convenience Security Lock the doors and arm the factory alarm. * Unlock the doors and disarm the factory alarm. * ö Open the trunk (hold button for at least 4 seconds). Panic ON (hold button for at least 4 seconds). Panic OFF Start the vehicle. Ê + Stop the vehicle. Ö Set car to idle mode when it is already running. Open and close the sliding door (driver side). ** Open and close the sliding door (passenger side). ** Cold Weather Start feature (see page 9 for more information). Remote Valet feature. / / + + + + Status request. Vehicle selection (hold button for at least 1.5 seconds.) This button is located on the back of the remote. Legend: Displayed icons (black); Hidden icons (gray) ö Commands followed by an asterisk (*) apply only to modules equipped with a security system. Only accessible with Chrysler Town & Country 2008-2010, Dodge Grand Caravan 2008-2010, and Volkswagen Routan 2009-2010. This command terminates the runtime, panic mode and alarm status (only if the factory alarm trigger monitoring feature is supported by the firmware). Temporary valet mode if activated a second time during rearming delay. Ê Start confirmation can take a few seconds except if the engine is already running. * ** Ö Refer to the vehicle user manual for more information on confirmations emitted by your vehicle (i.e. the horn and parking lights). These confirmations are different for each vehicle, depending which Bypass is used. Understanding the Confirmations Emitted by the 2-Way Remote The LCD displays the vehicle status at all time, the display is refreshed on every transmission or when the status of the vehicle changes pertaining that the “Status confirmation” function is enabled. The display shows the last confirmation received. © 2009 Directed Electronics. All rights Model: CHRSALL RS-CHLED & RS-CHLCD Rev.: 20091218 2-Way LED & LCD Remote Start Kits Page 8 The following diagram shows the usefulness of each icon of the display. Descriptions in CAPITAL letters show confirmations pertaining to the security system’s functions. 1 2 3 4 5 1 Transmission 10 16 2 Vehicle out of range 11 SECURITY SYSTEM STATUS 15 3 Reception 12 IGNITION STATUS SENSOR 14 6 13 7 12 8 Sentinel mode status 4 Unlocking 13 Remote starter status 5 Locking 14 HOOD STATUS 6 TRUNK LID STATUS 15 Valet mode status 7 DOORS STATUS 16 Vehicle identification 8 Battery charge indicator 9 Auxiliairy outputs status 11 10 9 * Only if the Factory Alarm Trigger Monitoring feature is supported by the firmware. Two types of confirmations are displayed on the remote: Command confirmation: These confirmations are command acknoledgement, the icon corresponding to the command is displayed to confirm reception of the command. Status confirmations: These confirmations are displayed when the status of a zone, monitored by the system, changes (i.e.: door openning, security system alarm state (only if the Factory Alarm Trigger Monitoring feature is supported by the firmware), etc. - it depends on which firmware you are using). Command confirmations are returned immediatly following a command transmission whereas the status confirmations may be returned up to 12 seconds after the event happened depending on the communication protocol between the hand-held unit and the vehicle. Remarks: When the remote receives a confirmation that is intended to a vehicle other that the one actually selected, most audible confirmations are made more discreet, vehicle icon flashes (1-4) to warn you that the display reflect the status of that specific vehicle. This is only applicable if the Factory Alarm Trigger Monitoring feature is supported by the firmware. When a command is transmitted, the vehicle selection gets back to the previously selected unless the confirmation was related to an alarm condition. In that case the selected vehicle is temporarely changed, to allow stopping the alarm condition without having to change the vehicle selection, then gets back to previously selected when the alarm condition is stopped. © 2009 Directed Electronics. All rights Model: CHRSALL RS-CHLED & RS-CHLCD Rev.: 20091218 2-Way LED & LCD Remote Start Kits Page 9 Out of range: In the event that the environement prevents the confirmation from being received by the remote control, all icons are cleared out. In this case, resend the command or send the status command to refresh the display. Upon Entering your Vehicle DO NOT TURN IGNITION KEY TO START POSITION. Automatic transmission vehicles Manual transmission vehicles To avoid turning the engine off when taking place behind the steering wheel, do not apply the brakes until you have placed the key in the ignition and turned it to the RUN position. To avoid turning the engine off when taking place behind the steering wheel, do not apply the brakes and do not remove the parking brake until you have placed the key in the ignition and turned it to the RUN position. Drive as usual. Drive as usual. Cold Weather Start Feature To activate the Cold Weather Start feature, press the LOCK and START buttons on the remote control and hold for 4 seconds. Press the LOCK and START buttons and hold for 4 seconds. OR The parking lights will flash once to confirm the operation. The engine will be started every 3 hours or 1.5 hours and will run for a period 15 minutes or 5 minutes. The runtime is defined with function option 16. The default value is every 3 hours for 15 minutes. The Cold Start Weather feature is deactivated after 24 hours or once the hood is open. To deactivate the Cold Weather Start feature, press the LOCK and START buttons again. The parking lights will flash twice to confirm the operation. This feature will also be disabled if the: § Remote Valet feature is activated. § Ignition is turned on. § Brake pedal is pressed. § Hood is opened. § Engine is not turned on within 24 hours. © 2009 Directed Electronics. All rights Model: CHRSALL RS-CHLED & RS-CHLCD 2-Way LED & LCD Remote Start Kits Limited One-year Consumer Warranty Rev.: 20091218 Page 10 For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.920-0007 07-06 This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. PROTECTED BY U.S. PATENTS: 5,719,551; 6,011,460 B1 *;6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6 , 3 4 6 , 8 7 6 B 1 ; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7 , 0 1 0 , 4 0 2 B 1 ; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; CDN. PATENT: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089 EUROPEAN PATENT:1,053,128 PAT. PENDING: 2,291,306; MADE IN CANADA © 2009 Directed Electronics. All rights