Owners Handbook 2007 Touring Caravans

Transcript

Owners Handbook 2007 Touring Caravans Contents 1 Welcome & Introduction 2 General Safety 1 Please read before using your new caravan. 2 Ventilation 2.1 High-Level Ventilation 2.2 Low-Level Ventilation 2.3 Ventilation in Separate Bedrooms 2.4 Gas Dispersal Holes 2.5 Petrol/Diesel Fumes 3 Fire Safety 3.1 Fire Extinguishers 3.2 In Case Of Fire 3.3 Fire Retardant Foams 3 Preparing for the Road 1 Caravan Towing Vehicle Weight Ratio 2 Nose Weight Indicator Jockey Wheel 3 Loading 3.1 Internal Loading & Checks 4 Pre-Tow Checklist & Hitch-Up 5 Winterhoff Stabiliser – Hitch Head Operation 5.1 Coupling 5.2 Activating the stabiliser 5.3 Checking the stabiliser 5.4 Disengaging the stabiliser 5.5 Uncoupling 6 Use of Your Caravans Breakaway Cable 6.1 Correct Procedure For Use 6.2 Where a Designated Attachment Point Is Provided On The Tow Bar 6.3 Where No Designated Attachment Point Is Provided On The Tow Bar 6.4 Other Means of Attachment 6.5 When The Breakaway Cable Is Attached Check To Ensure 7 Before Setting Off 8 Handbrake 9 Cables 4 1 2 3 4 Towing and Driving Reversing Speed Limits Setting Off Caravan Handling 5 1 2 3 Arriving On Site Check Site Regulations Selecting a Pitch Side-To-Side Levelling 3.1 Leveller Jack 3.2 Ramp 4 Front & Back Levelling 5 Parking on a Reverse-Sloping Site or Steep Hill Contents Explorer Group 2007 Touring Caravan Handbook 6 Getting Started 1 Electricity 1.1 Power Supply Charger 1.2 12v Systems: 2 Generator/Charger: 3 Electricity Mains Supply 4 Connecting To Mains Supply On Arrival at Site 5 Disconnecting Mains Supply When Leaving Site 6 Overseas Electrical Connection 7 Gas Supply 7.1 Connection 7.2 Gas Regulator 7.3 High Pressure Gas Hoses 8 Water 8.1 Operating instructions Ultraflow Filter Housing 01 Contents 8.2 Operating instructions Ultraflow Compact Housing 8.3 How to Use a Waterline 8.3.1 Connection to Ultraflow Filter Housing or Compact Housing 8.4 Draining Down Your Water System 7 Gas Safety Advice 1 Facts about LPG 2 Awning Spaces, LPG and Appliance Exhaust 3 LPG Gas System 4 Gas Barbecue Point 8 Electrical System 1 12v Power Supply 1.1 Battery Installation 1.2 Battery Maintenance 1.3 Generators / Charger 2 230v Power Supply 2.1 Mains Unit 2.2 Resetting the RCD 3 Automatic Charging System 4 Maximum Bulb Ratings for Internal Lights 02 9 How to Use Your Caravan’s Equipment 1 Electrical Control Panels 1.1 Avanté & Corona 1.2 Odyssey, Omega, Rallye Crusader and Buccaneer 1.2.1 Control panel for caravans without a fixed water tank. 1.2.2 Control Panel for caravans with an onboard water tank 2 Cooking equipment 2.1 Gas Hob 2.2 Gas Grill 2.3 Gas Oven 3 Refrigerator Operation 3.1 Thetford (Avanté and Corona models) Gas Operation / 230V Operation / 12V Operation 3.2 Dometic (Odyssey, Omega, Crusader, Rallye and Buccaneer Models) 3.2.1 Gas operation with electronic ignition 3.2.2 230V Operation 3.2.3 12V Operation 4 Water heater operation 4.1 Gas operation 4.1.1 230V Operation 5 Space Heater Operation 5.1 Gas Operation 5.2 Electric Operation 5.3 Fan Operation 6 Microwave (where fitted) 7 Battery Charger 8 Smoke Detector 9 Air Conditioning 10 Thetford cassette toilet 10.1 Preparing the Toilet for Use 10.2 Emptying the Toilet 11 Rooflights 11.1 The Omivent (12v) Rooflight 11.2 The Heki 2 & Heki Duette Luxus Rooflight 11.2.1 To open to the tilted position: 11.2.2 To open in the intermediate position: 11.2.3 To open in the ventilation position: 11.2.4 Closing the blinds: 11.2.5 Opening the Blinds: 11.3 Midi Heki Rooflight 11.4 Mini Heki 11.5 Standard MPK Rooflight 12 Windows 12.1 Polyplastic Window Opening 12.2 Seitz Window Opening 13 Blinds & Flyscreens 13.1 Blinds 13.2 Flyscreens 13.3 Door Flyscreen (If Fitted) 14 Taps 14.1 Kitchen Taps 14.2 Bathroom Taps and Showers. 14.2.1 Crusader, Rallye, Omega & Odyssey 14.2.2 Avanté and Corona 15 Exterior Doors Retainers 16 Gas Locker Door 16.1 Avanté and Corona Models 16.2 Odyssey / Omega / Crusader / Rallye and Buccaneer models 17 Internal Doors 17.1 Toilet/Shower Room Doors 17.2 Other Internal Doors 18 Magnetic Catches 19 Sprung Hinges 20 Sliding Doors 21 Bed Make Up 21.1 Parallel Lounge 21.2 L-Shape Lounge Double Bed 21.3 Bunk Beds 22 Removable Drawer Locker 23 TV Aerial 23.1 Status 315 Omni directional Aerial 23.2 Status 530 Directional Aerial 24 VHF Television Reception (Overseas only) 25 FM Radio Connection For both types of aerial. 26 BPW Nose Weight Indicator Jockey Wheel 10 1 2 3 4 Security Microtag© Robstop WS3000 Anti-Wind Corner Steadies CRIS – The Caravan Registration and Identification Scheme – VIN 5 Window Etching & Chassis Marking 6 Electronic Tagging 7 Explorer Protect Autowatch 650 Caravan Alarm 7.1 Basic Operation Arming the System 7.2 Disarming the System 7.3 Panic Alarm 7.4 Emergency Disarm. 7.5 Silent Arm and Disarm. 7.6 Sensors 7.6.1 Passive Infra Red Sensor 7.6.2 Leg Sensor 7.7 Enhanced Features Arming The System In “At Home” Mode. 7.8 Arming the System in Test or Buzz Mode 8 Additional Security Contents Explorer Group 2007 Touring Caravan Handbook 11 Care of Your Caravan 1 Exterior Cleaning 2 Glass Fibre Reinforced Plastic (GRP) 3 Acrylic Windows 4 Care Instructions for Seitz Windows 5 Care Instructions for Seitz Rooflights 03 Contents 6 Window Blinds & Flyscreens 7 ABS – A Frame Cover, Wheel Spats & Panels 8 Interior Walls 9 Furniture 10 Cooking Equipment 11 Carpets, Upholstery and Curtains 12 Shower Trays, Shower Room and Wash Basin Fittings 13 Water System 13.1 Truma Ultraflow and Ultraflow Compact Housing Routine Maintenance 13.2 Winter Storage 13.3 How to Prepare Your Water System for Winter Use 14 Compact or Filter system Accessories - Ultraflow Water Pump Assembly 15 Cleaning of all Taps 16 Water Containers 17 Water Systems – Sterilization 18 Truma Space Heater 19 Thetford Toilet 20 Chassis Mounted Spare Wheel Carrier 21 Tyres 21.1 Pressures 04 22 23 24 25 21.2 Tyre Wear and Damage Changing a Wheel Jacking Lubrication Maintenance of your BPW Chassis 25.1 Procurement of Spare Parts 12 1 2 3 Storage Long Term & Winter Storage Caravan Covers Power Drain 13 Warranty 1 3-Year Manufacturer's Warranty 2 Parts Covered By This Warranty for Years 1 - 3 3 Specific Exclusions for Years 2&3 4 Conditions Attached to the Warranty: 14 1 2 3 4 5 6 Code of Practice - Water Ingress The Code Conditions Attached To the Code Customer Obligation - Servicing Mains Electrics Spare Parts Remedial Work 15 Caravan Construction - Main Components 1 BPW Chassis 2 Braking System 3 Body Shell 4 Windows 5 Front Panel and Gas Bottle Locker Lid 6 Awning Channel 7 Additional Fixings to Your Caravan Shell 16 1 2 3 Equipment List Avanté & Corona Odyssey & Omega Crusader, Rallye & Buccaneer 17 Electrical Drawings 1 12n & 12s Socket & Plug Wiring Diagram 2 Electrical Drawings 3 Road Light Drawings 18 1 2 3 Technical Specifications Elddis Avanté Odyssey Crusader 4 5 6 7 8 9 10 Corona Omega Rallye Buccaneer Avanté / Corona Specials Odyssey / Omega Specials Odyssey / Omega Air Con Specials Contents Explorer Group 2007 Touring Caravan Handbook 19 General Questions 20 Glossary 21 2007 Explorer Group Retailer Special Editions 22 Annual Service Record Index 05 1 Welcome & Introduction WELCOME & INTRODUCTION Congratulations on choosing an Explorer Group Touring Caravan. This Owner's Handbook has been prepared for your guidance to help you derive the greatest amount of pleasure from the use of your caravan and your leisure time. We strongly recommend that you read this guide thoroughly so that you are fully aware of all the caravan's features, equipment and systems. Additional information and detailed appliance instruction manuals are also contained in your Owner's Information Pack. Your new Explorer Group caravan has been designed as a recreational vehicle and is intended for recreational use only. It is not intended for business use or for permanent habitation. The Explorer Group accepts no liability if the caravan is 06 used for any purpose other than recreational/holiday use. Your caravan has been designed for towing behind a normal motor car. Additional care should be exercised when towing with a 4x4 because of the 'off-road' nature of the suspension. Owners should not tow their touring caravans with commercial vehicles (including light and heavy goods vehicles). By following the instructions provided in this handbook and maintaining your caravan in a first class roadworthy condition, you are sure to have many years of carefree use. To ensure the very best quality and reliability all touring caravan designs and new developments are rigorously tested. Therefore the Explorer Group Ltd will accept no liability or uphold the warranty if the caravan is altered or modified in such a way that would adversely affect the reliability. Please Note: It is a condition of your warranty that the caravan must have an “annual service” done by an Approved Retailer or Service Centre, and a record is kept. Pages are provided in the back of this guide, for your assistance. Approved Retailers or Service Centres will be able to supply any replacement parts for your caravan, should the need arise, and in most case any accessories you may require. Please note that it is not possible to purchase replacement parts direct from The Explorer Group Limited. Changing market and supply situations may prevent us from maintaining the exact specification details in this guide and we therefore reserve the right to alter specifications as materials and conditions demand. Enjoy your new caravan. Model Year Touring caravans are designated by their model year. The 2007 model year runs from 1st September 2006 to 31st August 2007. Explorer Group Technical Approvals In order to ensure your new Caravan is safe to use the Explorer Group are members of and have been inspected by the following bodies. National Caravan Council (NCC) who operated a certification scheme to ensure compliance with the European safety standards for caravans. 1 Welcome & Introduction Explorer Group 2007 Touring Caravan Handbook National Inspection Council for Electrical Installation and Contracting (NICEIC) who carry out an annual inspection of the Explorer Group electrical installations within caravans. Confederation of Gas Installers (CORGI) who carries out annual inspection to ensure that the gas installation installed by the Explorer Group fully comply with all relevant regulations and standards. The Explorer Group are a ISO 9001:2000 approved manufacturer certified by SGS Limited 07 2 General Safety GENERAL SAFETY 1 Please read before using your new caravan. In order for you to get the most out of your new Explorer Group caravan it is necessary for you to be aware of the following. (i) Do not obstruct ventilators and clean them regularly, it is advisable to clean and check all the ventilators annually for blockages and where necessary rectify any blockages found. (ii) Inspect the high pressure flexible gas hose (available from your retailer) regularly for deterioration and renew as necessary, with approved type, in any case no later than the expiry date stated on the hose. (iii) Turn off all gas appliances and turn off the gas supply before towing your caravan. (iv) If your caravan is fitted with a gas barbecue point it is not designed to allow gas flow into your caravan and should never be used for this purpose. (v) Never use portable cooking or 08 heating equipment inside your caravan. Do not use your fitted cooking equipment as heating at any time. (vi) Never allow modification to your gas or electrical system unless qualified persons carry them out. All modification to the gas system should be carried out by a CORGI registered gas fitter. Any modifications carried out on the electrical system should be carried out by an electrician on the roll of the NICEIC or be a member of the ECA. (vii) It is recommended that you provide a dry powder fire extinguisher complying with ISO 7165 of at least 1KG capacity by the exit door and a fire blanket next to the cooker. Ensure you read the 'advice to occupier label' fitted to your caravan usually found on the inside of the wardrobe door. (viii) Never exceed your caravans Maximum Technical Permissible Laden Mass. (see Caravan Towing Vehicle Weight Ratio) (ix) The laden nose weight for your caravan should not exceed the lower of the following: • Towing vehicles maximum nose weight • Tow bar maximum nose weight • The caravan’s maximum nose weight which is 100kgs (x) Ensure heavy and large items are secured before towing your new caravan to reduce the risk of damage being caused while the caravan is in motion. (xi) When your caravan is connected to your towing vehicle it should be level or slightly nose down. An excessive nose down attitude or a nose up attitude could lead to instability when towing. (xii) When your caravan is loaded to its MTPLM and the weight distributed in accordance with the towing code, your caravan is designed to be towed at a maximum speed of 130kmh/80mph. However, your attention is drawn to the fact that in the UK the maximum speed allowed for towing a caravan is 100kmh/60mph. (xiii) It is illegal to tow your caravan whilst it is occupied. (xiv) If your caravan is fitted with a lift up bunk it is designed for a maximum weight of 11 stone and is not suitable for children under 3 years old without supervision. (xv) Do not leave children under 14 years of age unattended in your caravan. points are checked and cleaned (where necessary) on a regular basis. IMPORTANT Your attention is drawn to the notice affixed in the caravan’s wardrobe advising on fire prevention, ventilation and what to do in case of fire. 2.1 High-Level Ventilation This is always provided by fixed ventilation within the fitted roof skylight. All roof skylights fitted by Explorer Group provide fixed free area ventilation. These roof skylights should be cleaned annually by use of a small brush to remove any dust that may have accumulated around the mesh fitted. On some roof skylights the mesh can be easily removed to aid cleaning. On fan-assisted roof skylights it is essential that the fan is switched off prior to cleaning 2 Ventilation All caravans manufactured by the Explorer Group Limited are ventilated at both high and low level in accordance with BSEN 721 Safety Ventilation. The fixed ventilation points fitted in your caravan must not be blocked under any circumstances as your safety may depend upon them. It is advisable that the fixed ventilation 2.2 Low-Level Ventilation Low-level ventilation is provided under the front chest of drawers, except in an L shape layout, where it can be found either in the nearside or offside bed box. The exact position can be identified via the white or black plastic cover used to prevent the ventilation from being obstructed. In order to clean the ventilator, remove the cover by undoing the two screws and clean using a small brush. It is essential that the cover is replaced once cleaning is complete. 2.3 Ventilation in Separate Bedrooms In caravans with separated sleeping areas, separate ventilation is required and is provided via a roof skylight at high level and a ventilator at low level within a bed box. General Safety 2 Explorer Group 2007 Touring Caravan Handbook 2.4 Gas Dispersal Holes All appliances and gas unions have a gas dispersal hole nearby. It is essential that these are not blocked or made ineffective. 2.5 Petrol/Diesel Fumes The fitting of a tail pipe to your exhaust will reduce the possibility of fumes entering your caravan through the front fixed ventilation points. 09 2 General Safety 3 Fire Safety 3.1 Fire Extinguishers It is recommended that a 1 kg (2lb) minimum capacity dry powder fire extinguisher be carried inside your caravan at all times. A fat pan fire must not have an extinguisher aimed at it, but must be smothered with a fire blanket. 3.2 In Case Of Fire (i) Get everyone out of the caravan as quickly as possible using whichever exit is quickest including windows. Do not stop to collect any personal items. (ii) Raise the alarm. Call the fire brigade. (iii) Turn off gas container valve if safe to do so. 3.3 Fire Retardant Foams Under the requirements of the Consumer Protection Act 1987, the manufacturer has a responsibility to ensure that their product is as safe as possible. With this in mind all caravans 10 are equipped with either Combustion Modified High Resilient (C.M.H.R.) foam cushions or sprung mattresses. These foams are very much safer from a fire point of view than those previously used. In addition all upholstery is made of fire retardant fabric. 3 Preparing for the Road PREPARING FOR THE ROAD Before venturing out on to the road with your touring caravan, it is important that you prepare correctly. 1 Caravan Towing Vehicle Weight Ratio This ratio has a major influence on stability. It is recommended that: (i) The laden nose weight for your caravan should not exceed the lower of the following: • Towing vehicles maximum nose weight, • Tow bar maximum nose weight • The caravan’s maximum nose weight, which is 100kgs (ii) The actual laden weight of the caravan should always be kept as light as possible. The lighter it is whilst being towed on a road, the safer the outfit combination will be. (iii) The Caravan Club recommends a maximum caravan/towing vehicle weight ratio of 85% of the towing vehicle’s kerb weight providing both are properly maintained, fully serviceable and the other 12 recommendations in this Handbook are followed. (iv Whilst you can legally tow at a higher weight ratio than 85% (subject to manufacturers’ towing limits and driving license restrictions) towing a heavier caravan will increase the risk of instability, especially at higher speeds. (v) The greater the actual laden weight of the caravan in relation to the kerb weight of the towing vehicle the more careful and experienced the driver needs to be and the lower the speed at which instability could occur. WARNING It is strongly recommended the loaded weight of the caravan does not exceed the kerb weight of the towing vehicle. 2 Nose Weight Indicator Jockey Wheel New for 2007 is the Jockey wheel nose weight indicator which is fitted to the Crusader / Rallye and Buccaneer ranges. This can be used to give guidance on the actual nose weight your caravan is applying to your car’s tow ball. Please note that this should only be used as a guide. For information on how to use the nose weight indicator please go to the section on ‘How to Use Your Caravan’s Equipment’. 3 Loading Always lower and secure the jockey wheel and the four corner steadies (with the brace provided) before entering the caravan. This will ensure that the caravan does not tip up when you are inside. Please Note: Corner steadies should not be used as a jacking device. 3.1 Internal Loading & Checks When loading your caravan it is advisable to: (i) Distribute items evenly over the axle and as low as possible to optimize road holding and achieve the best possible braking effect. (ii) Do not overload on one side as this will cause the caravan to lean and affect the road holding and stability. (iii) Do not stow tins, bottles or heavy items in overhead lockers when towing. (iv) Loose articles should be stowed securely to avoid movement and possible damage. (v) Ensure that all lockers and cupboard doors are closed and secured. (vi) All Folding bunks are secure. (vii) The main dining table is stored in its transit position. (viii) If any fresh food is stored in the refrigerator that it is set for 12V operation and that the door is locked. (ix) All windows and rooflights are fully closed and locked. Never tow with windows on night setting. (x) Leave all curtains and blinds open to prevent damage in transit. If your caravan has a rear window this may aid visibility. 3.2 External Loading & Checks (i) Gas cylinders should only be stored, correctly positioned, and secured in the gas bottle locker. The gas should be turned off. (ii) The leisure battery is stored and secured in the battery locker box, set into the tray provided and secured. (iii) Any external connections (battery chargers, connecting cables etc), should be disconnected and stowed. (iv) Check that all exterior locker doors are secure and locked. (v) Secure and lock the main caravan entrance door. 4 Pre-Tow Checklist & Hitch-Up Having loaded the touring caravan and secured the lockers and main entrance door: (i) Check touring caravan wheel bolts are torque to the required level (See – Tightening Wheel Bolts). (ii) Check tyre pressures (Refer to the Technical Specification section) and tyre condition for roadworthiness. (iii) Ensure the jockey wheel is down, in good contact with the ground, clamp tightly secured, and the caravan handbrake is fully on. (iv) Wind up the corner steadies. (v) Reverse the car close up to the caravan’s hitch. It is advisable to seek assistance to guide you so that the car tow ball aligns with the caravan’s hitch. (Use of the caravan handbrake is advised. Extreme caution should be taken if manoeuvring the caravan down hill or on wet, slippery surfaces). (vi) Make sure the jockey wheel height is sufficient for the hitch head to clear the towing vehicles tow ball. (v) Manoeuvre the hitch head over the tow ball and lower the jockey wheel using the winding handle, until the hitch head opening sits comfortably over the tow bar ball. Preparing for the Road 3 Explorer Group 2007 Touring Caravan Handbook 5 Winterhoff Stabiliser – Hitch Head Operation 5.1 Coupling The opened ball coupling is placed over the tow ball of the towing vehicle. As the coupling load is applied to the tow ball the coupling will automatically close, this is indicated when the security lugs become parallel on the 13 3 Preparing for the Road side of the housing. (Fig 5.1) Fig 5.2 Fig 5.1 5.2 Activating the stabiliser The operating handle will not operate until the automatic closing function has been engaged. The handle can now be fully pushed down. The hitch will remain coupled with the stabiliser deactivated to facilitate easier manoeuvring. 14 5.3 Checking the stabiliser With the caravan coupled to your towing vehicle and the stabiliser activated, the condition of the friction linings can be checked. The wear indicator (As shown in Fig 5.2) is within the top of the operating handle. The bar graph is marked with + and – symbols with + indicating good condition of the pads and – indicating that the pads should be checked. 5.4 Disengaging the stabiliser Lift up the operating handle with care to release the sprung loaded stabiliser function. Fig 5.4 5.5 Uncoupling Before uncoupling disconnect the electrical connections and breakaway cable. Also check that it is safe to uncouple your caravan taking into account any gradients. With the stabiliser function disengaged, simultaneously pull back and lift the operating handle, this swings the securing lugs out of the locked position allowing the operating handle to be lifted into the fully open position. Before operating the jockey wheel, which will lift the caravan free of the tow ball, check that both caravan and towing vehicle handbrakes are applied! in motion. It's also a legal requirement to use the breakaway cable whenever it's provided. If the caravan is not to be used for any lengthy period of time we recommend the ball coupling is kept in the closed position. This can be done easily by pressing the safety ball into the ball space and slowly closing the operating lever. The purpose of the breakaway cable is to apply the caravan's brakes if it becomes separated from its towing vehicle. The cable assembly is designed to part, allowing the caravan to come to a halt away from the towing vehicle. Please note: The WS3000 ball coupling can be locked in both the coupled and uncoupled condition with the ROBSTOP WS3000 hitch lock however it is recommended that the Robstop is removed for towing. Construction - Usually a thin steel cable, possibly plastic coated, and fitted with a means of attachment to connect to the towing vehicle. 6 Use of Your Caravans Breakaway Cable UK LAW requires that all caravans with brakes (e.g. caravans, horse boxes, car transporters etc), built on or after 1st October 1982, is fitted with a safety device to provide protection in the unlikely event of the separation of the main coupling while Operation - The cable should be able to pull tight to engage the caravan's brakes without any hindrance to its action, if the main coupling of the caravan separates from the towing vehicle. It should never become taut during normal use. If in doubt contact your Retailer or Service Centre. (ii) Make sure the cable runs as straight as possible, and goes through a cable guide underneath the caravan coupling. (iii) Determine whether or not you have a designated attachment point (a feature of the tow bar which has been identified by the tow bar supplier as being for the attachment of a breakaway cable). Preparing for the Road 3 Explorer Group 2007 Touring Caravan Handbook 6.2 Where a Designated Attachment Point Is Provided On The Tow Bar (i) Pass the cable through attachment point and clip it back on itself (Figure 1 below); or (ii) Attach the clip directly to the attachment point (Figure 2 below). Note -this must be specifically permitted by the caravan manufacturer's guidance, as the clip may not be sufficiently strong. 6.1Correct Procedure For Use (i) Check cable assembly for damage. 15 3 Preparing for the Road Step 1 Step 2 Step 3 Fig 5.6.2 6.3 Where No Designated Attachment Point Is Provided On The Tow Bar (i) Fixed Ball - Loop the cable around the neck of the tow ball. If you fit the cable like this use a single loop only (Figure 3 above). (ii) Detachable Ball - You must contact the tow bar supplier for advice. 6.4Other Means of Attachment Alternatively, it may be possible to attach the cable assembly to a permanent part of the tow bar structure with the approval of the tow bar supplier, or to an accessory sold for the purposes of breakaway cable attachment. 16 6.5 When The Breakaway Cable Is Attached Check To Ensure (i) That the cable cannot snag in use on the caravan hitch, jockey wheel or any accessories e.g. a stabiliser, bumper shield, cycle carrier etc. (ii) That there must be sufficient slack in the cable to allow the towing vehicle and caravan to fully articulate without the cable ever becoming taut and applying the brakes. (iii) That it is not so slack that it can drag on the ground. Leave it too loose, and the cable may scrape along the ground, and be weakened so that it fails before doing its job! 7 Before Setting Off (i) Connect the 12N and 12S plugs on the caravan A-frame to the towing vehicle. (ii) Check that all tail-lights, brake lights, road lights and indicators work correctly. (iii) Ensure that the correct vehicle license / registration plate is attached to the rear of the touring caravan. (iv) Using the jockey wheel lift the tow ball slightly to check hitch is locked onto the ball (v) Wind up the jockey wheel until the wheel supports locate into the cut out sections at the base of the winding section. (vi) Raise and secure the jockey wheel using the clamp. The jockey wheel should be parallel to the direction of travel at all times. (vii) Check condition of and secure the breakaway cable to the tow vehicle. Please Note: If having followed this advice, you feel you cannot achieve a satisfactory cable arrangement, consult your caravan or tow bar supplier or service agent. 8 Handbrake Your caravan is fitted with BPW running gear and handbrake. It is essential that prior to towing you ensure that your handbrake is in the fully off position. This can be confirmed by ensuring that the handbrake arm is resting on the blue stop fitted to the side of the A frame as shown in Fig 8 below. Fig 8 Preparing for the Road 3 Explorer Group 2007 Touring Caravan Handbook 9 Cables For peace of mind, you may wish to check the ability of the cables to be able to cope with towing the vehicle at extreme angles before setting off. To do so position the vehicle at alternate extreme angles and check that the cables do not pull too tight, are liable to stretch or become unplugged. No cables should be allowed to touch the ground as they will wear and become damaged and ineffective. 17 4 Towing and Driving 3 Setting Off (i) Let the clutch in smoothly on the towing vehicle. Allow more engine speed to produce the power to move the additional weight of the caravan. (ii) Avoid wear and tear on the clutch and transmission by taking extra care not to ‘ride’ the clutch. (iii) Change gears smoothly. Try not to jerk the clutch. TOWING AND DRIVING 1 Reversing It is advisable to have a second person available when reversing the caravan. Start practising by choosing a lefthand bend for ease. Reverse slowly; turning the wheel, initially the opposite way to the direction you want the caravan to go. Now the front of the caravan is nudged out and is moving the rear in the intended direction. Take care not to hit the van with the car! Midways through the manoeuvre, when the caravan is correctly angled, reduce speed to a crawl and gradually apply opposite lock. Make the car follow the caravan round then finally straighten up. Please Note: Proficiency at reversing can only be achieved with practice. 18 Fig 1 2 Speed Limits Normal road towing: 50mph Motorways (including dual carriageways): 60mph 4 Caravan Handling (i) Allow for the caravan being wider than the car. Ensure you have a clear view to the rear. This may require the fitting of extended mirrors for towing your caravan. (ii) Do not bump the kerb with the caravan wheels. (iii) When passing other vehicles, allow more than the normal clearance for driving solo. (iv) Allow longer to obtain a fast enough speed to pass other vehicles. (v) Allow for the vehicle being twice its normal length. Do not suddenly swing out. (vi) Carry out all manoeuvres as smoothly as possible. (vii) Use the nearside wing mirror to check the caravan has clearly passed other road users when overtaking and changing lanes. (viii) Adverse weather conditions may affect the steering and braking characteristics of your caravan. 4 Preparing for the Road Explorer Group 2007 Touring Caravan Handbook 19 5 Arriving on Site ARRIVING ON SITE 1 Check Site Regulations On arrival at a site, you should always check the site regulations. This will help avoid any unnecessary conflict with site management and other site users. 2 Selecting a Pitch Carefully select where you wish to place your caravan. The site should be as level as possible, preferably not under or near trees, well drained and away from possible boggy areas. Consider how you will move the caravan when it is time to leave the site. On sloping ground it is better to pitch facing downhill, especially during wet weather. 3 Side-To-Side Levelling A quick glance at your pitch should tell you if you are likely to need side to side levelling i.e. levelling across the axle. On uneven ground lateral levelling is accomplished by the use of a leveller jack or ramp and a spirit 20 level placed 'across' the caravan floor (not supplied). 3.1 Leveller Jack Place the leveller jack, folded flat, in front of the wheel needed to be raised to level the axle. Tow the caravan onto the leveller jack and adjust the height until the spirit level shows that the caravan is laterally level. 3.2 Ramp (i) Reverse onto your pitch about 30cm (12”) further back than you wish to end up. (ii) Then place the levelling ramp in front of the wheel that needs to be raised. (iii) Place a spirit level parallel to the axle on the A-frame or just inside the caravan door. It helps to have two people at this point. One should drive the car very slowly forward moving the caravan wheel up the ramp, and the other should indicate when the spirit level bubble is in the middle. Whichever method you use, and once level: (i) Apply the caravan handbrake and chock the caravan wheel if necessary. (ii) Lower the jockey wheel to ground level before unhitching. (See index uncoupling) You should then park your car, usually next to the caravan furthest away from the door side. Please Note: On upward facing pitches when the hydraulically damped drawbar of the hitch becomes fully extended, it will be necessary to compress the drawbar slightly in order to achieve a clean' unhitching. With the caravan brake on, reverse the towing vehicle about 2.54cm (1”) to release hitch lock tension and using the jockey wheel adjustment, unhitch the caravan as previously described. 4 Front & Back Levelling This should be done only when the lateral levelling is complete. (i) Place the spirit level pointing front to back just inside the caravan door or on the A frame. (ii) Then raise or lower the jockey wheel until the caravan is horizontally level. Please Note: If there is a significant front to back slope, you may need to place a block under the jockey wheel. (iii) Next, wind down the corner steadies onto load spreaders (blocks of wood a minimum of 15.25cm (6”) square or 'Big Foot' steady attachments) until they are firmly set against the ground. to use. 5 Parking on a Reverse-Sloping Site or Steep Hill For successful parking on a reverse slope or steep hill, the operator need only apply the handbrake with one hand while gently but purposely inching the caravan a small distance backwards with the other. 5 Arriving on Site Explorer Group 2007 Touring Caravan Handbook CAUTION Never enter the caravan without first lowering the four corner steadies with the brace provided. Corner steadies should not be used as a jack. Take care not to lift the caravan wheels. Please Note: It is possible on very uneven sites that when fully extended blocks may be required under the corner steadies to achieve this. It is important that the caravan is correctly levelled to ensure the correct working of the refrigerator, cooker etc. (iv) Now that your caravan is level, place the caravan step in front of the door ensuring that it is stable and safe 21 6 Getting Started at 50 hertz AC supply. GETTING STARTED You have arrived at your destination and now want to start to enjoy your new Explorer Group caravan. The following is a step by step guide to connecting your services and getting everything in your caravan working. 1 Electricity 1.1 Power Supply Charger Your caravan is fitted with a power supply/charger. This will charge the caravan battery when fitted and also power the 12V systems in your caravan. It is recommended that you always carry a leisure battery. The Charger is fully automatic and will not overcharge the leisure battery. 1.2 12v Systems: Your caravan is fitted with an automatic system for selection of power. 22 When connected to the 230V site supply the automatic Power Supply/Charger will charge the leisure battery and the 12V systems. When connected to the car (always disconnect 230V supply), the system automatically switches to the car supply. When the ignition is switched on the 12V system in the caravan is automatically switched off, car power is supplied to the refrigerator and battery charging is in operation. 2 Generator/Charger: When connecting to a generator, always switch off the RCD, start the generator and allow running for a few minutes to stabilize. When this has happened, switch the RCD to the ON position. 3 Electricity Mains Supply Your caravan's main electrical installation is designed to run on 230V 4 Connecting To Mains Supply On Arrival at Site Before connecting the caravan installation to the mains supply, check that: (i) The mains supply is suitable for your installation and appliances, i.e. whether it is AC or DC and whether it is at the correct Voltage and frequency. (ii) Your caravan is properly earthed. Never accept a supply from a socket outlet or plug having only two pins, or from a lighting outlet. (iii) Any residual current device (earth leakage circuit breaker) in the mains supply to the caravan has been tested within the last month. In case of doubt, consult the site owner or their agent. (iv) Make sure that the switch at the site supply point is off and that all electrical equipment in the caravan is switched off by ensuring your caravan mains isolating switch on the MCB is in the 'OFF' position. all electrical lights and appliances should cease to operate. Reset, and then check the electrical system is operational. (x) Finally in order to get your 12V system operational, ensure the master 12V switch is in the on position. Pages 32 and 33 for further details on the control panel fitted. ELECTRICAL WARNING Attention: Always disconnect the electrical connector between the towing vehicle and the caravan before connecting a mains electric supply to the caravan and before charging the caravan battery by any other means. Once the above checks have been made: (v) Remove any cover to the electricity inlet provided on the caravan, and insert the female connector of the flexible orange supply cable as shown. (vi) Locate the site supply and remove any cover from the socket outlet provided at the supply point. Insert the male plug at the other end of the flexible orange supply cable. Switch on the main switch at the site supply point (if appropriate). (vii) Place any surplus cable under the caravan. Ensure that the surplus cable is not coiled up as it could overheat. (viii) The MCB main electricity supply switch should be put in the 'ON' position. (ix) Check the RCD is working by pressing the test button. Once pressed Getting Started 6 Explorer Group 2007 Touring Caravan Handbook 5 Disconnecting Mains Supply When Leaving Site (i) Switch 'OFF' at the caravan mains isolating switch. (ii) Remove the male plug from the site supply. (iii) Disconnect the female plug from the caravan and store the cable in an appropriate locker. 6 Overseas Electrical Connection Please Note: Connection to a mains Voltage supply OVERSEAS requires particular attention. Care must be taken when connecting supplies abroad since the supplies can be of REVERSE POLARITY. 23 6 Getting Started The significance of REVERSE POLARITY is that when equipment is switched off, it may not be electrically isolated. The only certain way of making equipment safe is to unplug it. A means of checking the polarity of the mains supply when overseas is recommended. There are available several proprietary makes of equipment for the purpose. If it can be achieved, it is preferable to connect live to live, and neutral to neutral to maintain full electrical protection. CHECK all caravan equipment is setup to accept the site supply before actually switching on. 7 Gas Supply Your caravan is designed to operate using either propane or butane liquefied petroleum gas at 30M/bar. Gas can be obtained from your caravan dealer. Your caravan is 24 designed to accept a maximum 2 x 6kg Truma BP gas bottles. 7.1 Connection Make sure that heating and cooking appliances and gas cylinders are switched off. Space Heater Refrigerator Cooking Appliance Each gas appliance is connected to its own gas isolation tap. These are identified on the tap via a label. Below is a key to identify each label. To operate the tap the arrow on the tap shows the direction of flow for the gas. The arrow should be pointing towards the appliance for the appliance to operate. There will be a small label next to the bank of taps under the cooker, which is also reproduced below: Fig 7.1 Water Heater Hob Gas On/Off 7.2 Gas Regulator Your new Explorer Group caravan has been fitted with a fully approved gas regulator designed to operate at a gas pressure of 30Mbar. Your regulator is fitted with a test point, which is accessed via the inlet at the side of the regulator. This access point is only for carrying out gas pressure tests and should not be used for any other purpose. CAUTION It is strongly recommended that only CORGI approved gas fitters carry out any work on your caravan's gas installation. spanner. Once the hose is securely connected turn on the gas tap above the regulator, then turn on the gas bottle to allow gas to flow into the caravan. In order to make all your caravans gas appliances operational it is necessary to open each appliance gas tap as detailed in 6.1 above. All your gas appliances should now be operational. Instructions on how to use each appliance are detailed later in your handbook. 7.3 High Pressure Gas Hoses You should only connect to this regulator using an approved highpressure hose of length not exceeding 450mm from the gas cylinder to the regulator. These approved highpressure hoses are available from your Explorer Group Retailer. These hoses are connected using screw thread fittings, which will make a seal if connected and tightened using a 8 Water Your caravan will be supplied with either a Truma Ultraflow filter housing or a Truma Ultraflow Compact housing and submersible water pump (refer to Equipment Lists section to confirm). Getting Started 6 Explorer Group 2007 Touring Caravan Handbook 8.1 Operating instructions Ultraflow Filter Housing (i) Raise the lid; clean both the water socket and the plug of the pump assembly. (ii) Plug the pump assembly into the socket. WARNING Aerosols and highly flammable liquids must not be stored in the compartment behind, or adjacent to, any gas appliance. Some industrial LPG appliances operate at high pressure and require a ‘high pressure’ regulator. This often has an adjusting handle on it. NEVER use such a regulator on a caravan. Ventilation holes must be clear at all times. (iii) Place the pump into the water container, ensuring that it is fully 25 6 Getting Started submerged before operating the system. (iv) The dust cover (7) is to stop contaminates falling into the water container. (v) To remove the pump assembly from the Ultraflow Filter Housing, pull the lower trigger and pull out the hose plug. Please Note: Do not remove by pulling the hose or electric cable. 8.2 Operating instructions Ultraflow Compact Housing (i) Raise the lid; clean both the water socket and the plug of the pump assembly. (ii) Plug the pump connector into the socket. 8.3 How to Use a Waterline (iv) Place the pump into the water container, ensuring that it is fully submerged before operating the system. (v) The dust cover (8) is to stop contaminates falling into the water container. (vi) To remove the pump assembly from the Ultraflow Compact Housing, pull the lower trigger and pull out the hose plug. Please Note: Do not remove by pulling the hose or electric cable. Please Note: When using the Winter Kit the blanking plug provided will be fitted to the housing not being used. 26 CAUTION Do not under any circumstances connect your caravan to the mains water supply without the pressure reducer fitted. Damage will occur to the caravan’s water system! Max. Working inlet pressure: 7 bar. Static pressure: approx. 0.8 – 1 bar 8.3.1 Connection to Ultraflow Filter Housing or Compact Housing (i) Uncoil the hose and screw tap adaptor (1) to the drinking water stand pipe and plug in the hose adaptor (2). (ii) Raise the lid; clean both the water socket and the Water line plug. Push the plug into the socket. Turn on the mains water supply and check for leaks. Open one of the taps and purge any air that maybe trapped in the water system. To remove, pull the lower trigger (3) and pull out the hose plug. 8.4 Draining Down Your Water System (i) It is essential that you drain down your caravan water system when it is not in use. This is most important during winter months to protect against frost damage. (ii) Disconnect the water pump and switch off power supply. (iii) Remove the water heater fuse from the switch spur and store in a safe place. (iv) Open the safety drain valve on the water heater located next to the water heater. (v) Open all taps and remove all plugs from sinks and showers. Lever operated taps should have the lever put into the up and central position. (vi) Open the drain outlets on the outside of your caravan. (vii) If an onboard water tank is fitted ensure that the drain tap on the tank is open. (viii) Adjust the level of the caravan to ensure that the drain outlet is at the lowest point of the caravan. This will aid the flow of water to ensure all water is drained off. After 30 minutes level the caravan and prepare it for storage if necessary. 6 Getting Started Explorer Group 2007 Touring Caravan Handbook 27 7 Gas Safety Advice GAS SAFETY ADVICE In the event of a suspected gas leak the gas must be turned off using the isolation valve on the gas bottle. A competent gas fitter should then check the system before it is used/reused. Regularly check flexible gas hose, joints and connections for tightness. Finally, make sure that each gas appliance is working efficiently to the recommendations of the appliance manufacturers. point. 2 Awning Spaces, LPG and Appliance Exhaust There is no danger of pollution of an enclosed awning space from the LPG exhaust from a refrigerator venting into it. Space heaters may produce sufficient exhaust to pollute the awning space, if it is totally enclosed, from a general comfort, smell and hygiene point of view. In extreme cases there could be a build up of carbon dioxide to a dangerous level. Caravan owners are advised to allow some fresh air circulation in the awning space when such appliances are in use. See Index – Ventilation 1 Facts about LPG • LPG is not poisonous. • Bi-products are harmless. • LPG is dangerous if all air and oxygen is excluded. • LPG has been given a smell by the manufacturers in order to identify leaks. • The gas is heavier than air and therefore sinks to the lowest 28 Please Note: Ventilation holes must be clear at all times. 3 LPG Gas System The Explorer Group does not recommend the use of any external cylinders. All cylinders in use should be within the gas locker provided. If you wish to utilise a larger cylinder and have this outside the gas locker then the connecting hose must not exceed 750mm. It is recommended that no flammable material is stored or placed with 300mm of any open flame. Your attention is also drawn to the fact that the surface of the Space Heater in your caravan will get hot when in use. You are advised not to use any additional gas appliances outside your caravan unless it is a Gas Barbecue connected via the Barbecue point supplied with your caravan. Please ensure that you have read the operating instructions for each gas appliance contained in your Owners Information Pack. Please ensure that any gas hose left unconnected is protected from dirt or other foreign bodies entering the hose. 3 Gas Barbecue Point Your caravan may be fitted with a gas barbecue point. The gas barbecue point, when fitted, is situated on the nearside towards the front. This point is for use with a gas barbecue only. Simply lift up the flap, unplug the red plastic end cap and connect the appliance in accordance with the gas barbecue manufacturer’s instructions. CAUTION Do not use a gas barbecue inside the awning. ALWAYS use the appliance in the open air. 7 Gas Safety Advice Explorer Group 2007 Touring Caravan Handbook There will be an isolation valve fitted next to the Barbecue point. This is an automatic valve, which cannot be operated unless a connection has been made to the Barbecue point. Do not apply any force to this value. 29 8 Electrical System ELECTRICAL SYSTEM 1 12v Power Supply 1.1 Battery Installation Your caravan will be fitted with a BCA Leisure charging and power distribution unit. If you wish to install a leisure battery please ensure that it is placed on the battery tray supplied with your caravan. Then place the tray in the battery locker fitted to the side of your caravan. Connect the battery to the clamp fittings connected to the connection leads within the battery box. The Explorer Group recommends that you use sealed for life leisure batteries of a minimum rating off 40 amperehours at 20 hours discharge rate. 1.2 Battery Maintenance Your leisure battery should be maintained in accordance with the manufacture’s instructions. For 30 information on the automatic charging system in your caravan please refer to ‘Automatic Charging System’ in the index. Do not charge your leisure battery with any charger other than that supplied. Failure to comply may cause damage to your battery. If you remove your leisure battery, ensure that it is not placed on a cold surface as the battery will deteriorate more rapidly than if stored at a suitable temperature 1.3 Generators / Charger All electrical equipment fitted in your new caravan can be run from either a controlled generator or charger whose output is maintained between 11volts and 14volts. At least once every 3 years, the caravan electrical installation should be inspected and tested, and a report on its condition obtained, as prescribed in British Standard BS7671. 2 230v Power Supply 2.1 Mains Unit The Mains Unit replaces the conventional fuse box. Similar, but larger ones are often fitted in new houses. The unit, normally located in the wardrobe, gives overloads and earth leakage protection for the 230V electrical supply in your caravan. For normal operation all switches on the unit need to be in the ON position. The switches on the left of the unit are known as MCB’s (miniature circuit breakers). These take the place of the conventional fuse but are more convenient. In the event of a fault the MCB ‘trips’ i.e. automatically moves to the OFF position. After elimination of the fault the MCB can be re-set by switching to the ON position (against the spring pressure in an upwards direction). If an earth fault develops, or a person was to touch a live piece of equipment, the leakage of current to earth should immediately operate the RCD (residual current device) and ‘trip’ the main switch, to the OFF position. This switch can only be reset after elimination of the fault. Please Note: In case of difficulty, consult an approved electrical installation contractor (who may be the local electricity board). It is dangerous to attempt modifications and additions yourself. Lamp holder-plugs (bayonet- cap adaptors) should not be used under any circumstances. 2.2 Resetting the RCD To re-set, operate the switch as for MCB’s. Periodically, the RCD should be checked by operating the test button marked ‘T’. The unit should immediately switch to the OFF position. If the unit does not switch off then a qualified electrician should be consulted. If the unit does switch off, the test is complete and the switch can be re-set restoring the supply back to normal. Please Note: Simultaneous operation of all of the 230V mains electrical equipment may not possible. A typical UK caravan site mains hook-up point provides a maximum output of 10 amps and on some continental sites the available output may be as low as 5 amps. If your loading exceeds the site supply it may trip the site circuit breaker. Please check the available mains output with your site operator. The following items need to be added together if used simultaneously. 230V mains equipment typical consumption figures: ∑ • Refrigerator 0.50 amps ∑ • Charger 0.50 amps ∑ • Water heater 3.9 amps ∑ • Blown air heaters 8.5 amps ∑ • Colour TV 2.50 amps ∑ • Microwave 4.00 amps ∑ • Air conditioning 4.00 amps caravan site. The 12V system, with the exception of the 12V refrigerator and battery charging, will not operate when the caravan is connected to the towing vehicle. CHECK all caravan equipment is setup to accept the site supply before actually switching on. Electrical System 8 Explorer Group 2007 Touring Caravan Handbook 4 Maximum Bulb Ratings for Internal Lights Type of Light 12V Fluorescent Lumo 12V Fluorescent Crown 12V Zoe eyeball Lights 12V Nova Halogen Downlighter 230V Wall lights Maximum Bulb Rating 9 watt 9 watt 10 watt 10 watt 20 watt 3 Automatic Charging System The battery charger will operate automatically when the caravan is connected to the mains outlet on a 31 8 Electrical System Please Note: Ensure that you only replace a blown bulb with one of the same rating. Never replace a bulb with one with a higher rating. You should ensure that when fitted, no bulb is in contact with the surface of the lamp or shade. 32 9 How to Use Your Caravan’s Equipment HOW TO USE YOUR CARAVAN’S EQUIPMENT Congratulations on your purchase of a new Explorer Group caravan. Within this section of your caravan’s handbook we will give you brief details on how to operate all of the caravan’s equipment from the gas cooking equipment to the widow blinds. For further details on the major equipment within your caravan please read the individual appliance instructions contained with your user information pack. 34 that you have connected the mains connection cable to a mains hook up and that the mains isolation switch is in the on position. 1 Electrical Control Panels Your Explorer Group caravan will be fitted with one of the following electrical control panels. 1.1 Avanté & Corona switched on. A green light indicates that the battery is fine this will change to amber and then red as the battery discharges. This unit also contains a 12V socket and TV aerial connection. A mains 230V socket is also fitted to this unit. The Avanté and Corona are also fitted with a 12V master switch, which is positioned near the exterior door. 1.2 Odyssey, Omega, Rallye Crusader And Buccaneer Your new Odyssey, Omega, Rallye, Crusader or Buccaneer Explorer Group caravan will be fitted with one of the following control panels: Please Note: Before attempting to use any gas equipment please ensure that the gas bottle is connected securely to the caravan’s regulator via a high pressure gas hose and the bottle valve is in the on position. Also ensure the appliance isolation valves are in the on position as shown in the gas system section. The right hand control panel operates the water pump by pressing the switch marked ‘Pump’ down. Whilst the pump is running the bottom neon light marked ‘Pump Run’ will illuminate. Please Note: Before attempting to use any electrical appliance ensure The top neon light will give a battery condition reading when the power is Control panel for caravans without a fixed water tank. Control Panel for caravans with an onboard water tank. (vii) When the right hand button is depressed the level of the water tank will be displayed. 2 Cooking equipment (i) To operate the 12V systems for your caravan depress the 1st switch. (ii) To operate the pump for your water system depress switch marked with a tap symbol. (iii) When the pump is running the neon light will illuminate. (iv) When the left hand button is depressed the available battery Voltage will be displayed. (v) The right hand button has no function on this control panel. (i) To operate the 12V systems for your caravan depress the 1st switch. (ii) To operate the internal pump for your water system put switch marked with a tap to the up position. (iii) To operate the external pump for your water system put switch marked with a tap symbol to the down position. (iv) The middle position of this switch is the off position. (v) When either pump is running the neon light will illuminate. (vi) When the left hand button is depressed the available battery voltage will be displayed. WARNINGS (i) All pans should be mounted centrally over the burners, even when cooling, to protect adjacent walls. (ii) Do not lower the glass cover until hob has cooled down. (iii) Glass lids may shatter when heated. Turn off all burners and grill before shutting the lid. The glass cover should be raised when operating the grill. (iv) Accessible parts may be hot when the grill and oven are in use. Young children should be kept away. (v) Do not use grill or oven as a space heater. How to Use Your Caravan’s Equipment 9 Explorer Group 2007 Touring Caravan Handbook 2.1 Gas Hob (i) Turn the individual gas tap for the burner you wish to light. (ii) If the hob is fitted with electronic ignition then depress the ignition 35 9 How to Use Your Caravan’s Equipment button, which can be found on the front of the oven next to the oven control, while depressing the gas tap. The depressing of the gas tap overrides the flame failure device fitted to the burner. If the burner fails to light within 20 seconds then release the gap tap and wait 30 seconds before trying again. (iii) Once the burner lights it will be necessary to keeps the tap depressed for about 5 to 10 seconds to ensure that the flame failure device is heated up enough to operate. (iv) If your hob is not fitted with electronic ignition then it is recommend that you use spark igniters rather that a gas lighter which has a naked flame. Burner controls 36 Ignitor button Grill control knob 2.2 Gas Grill (i) Turn the grill control knob to the high flame position and with the knob depressed press the electronic ignitor button. If the grill does not light within 20 seconds then turn off the grill control knob for at least 30 seconds before trying again. (ii) Once the grill lights it will be necessary to keep the grill control knob depressed for 5 to 10 seconds to ensure the flame failure device is heated enough to operate. 2.3 Gas Oven (vi) Turn the gas oven control knob to maximum then depress the knob while pressing the electronic ignitor button. If the oven does not light within 20 seconds turn off the control knob and wait for 30 seconds before trying again. (vii) Once the oven is lit it will be necessary to keep the control knob depressed for 5 to 10 seconds to ensure the flame failure device is heated up enough to operate. NOTE: The refrigerator should not be operated on LP gas whilst being towed or when on a petrol station forecourt. Oven control knob 3 Refrigerator Operation When the caravan is on tow, the refrigerator should only be operated electrically, i.e. from the 12V battery in the towing vehicle and not by means of the bottled gas. The refrigerator can be run on 230V or LP gas whilst stationary. Changing between these modes of operation is carried out by means of the controls shown on the relevant control panel on the refrigerator. CAUTION Only use one source of energy at a time. 3.1 Thetford (Avanté and Corona models) Gas Operation (i) Turn the refrigerator control knob, on the left hand side of the refrigerator, onto gas as shown by the flame symbol. (ii) Turn the gas control knob, on the right hand side of the refrigerator, to maximum i.e. all the way clockwise. (iii) Now depress the gas control knob and a clicking should be heard. Once the gas ignites the needle will move from the white zone into the green zone. (iv) If the refrigerator fails to light after 20 seconds release the gas control knob and wait for 30 seconds before trying again. Please Note: If the refrigerator is being used for the 1st time or has been stood for a while then it may take a couple of attempts to purge the gas pipes of air before the refrigerator lights on gas. 230V Operation (i) Ensure that the caravan is connected to a mains hook up and that the mains control panel is switch on. (ii) Turn the refrigerator control knob, on the left of the refrigerator, to the mains position as indicated by the plug symbol. Refrigerator should start to operate on mains. (iii) Set the refrigerator temperature on the thermostat the bigger the dot the colder the temperature. How to Use Your Caravan’s Equipment 9 Explorer Group 2007 Touring Caravan Handbook 12V Operation (i) Turn the refrigerator control knob to the 12V position as indicated by the battery symbol. Please note that this function is only available when the caravan is connected via the 12n and 12s plugs to a towing vehicle. 37 9 How to Use Your Caravan’s Equipment 3.2 Dometic (Odyssey, Omega, Crusader, Rallye and Buccaneer Models) Gas operation with electronic ignition (i) Turn the main refrigerator control, to the left of the refrigerator, onto the gas setting the green light next to the gas setting should illuminate. (ii) Ensure the gas control, to the right of the refrigerator is in the maximum position. (iii) If the burner has not lit the green light will flash to indicate that the gas has failed to light. If this occurs then turn the refrigerator control to off and then try again. Energy selector switch 38 Thermostat Knob Please Note: If the refrigerator is being used for the 1st time in a while then it may take a couple of attempts to purge the gas pipes of air before the refrigerator lights on gas. 230V Operation (i) Ensure that the caravan is connected to a mains hook up and that the mains control panel is switch on. (ii) Turn the refrigerator control knob, located on the left of the refrigerator, to the mains position as indicated by the plug symbol. The refrigerator should start to operate on mains. 12V Operation (i) Turn the refrigerator control knob to the 12V position as indicated by the battery symbol. Please note that this function is only available when the caravan is connected via the 12n and 12s plugs to a towing vehicle. 4 Water heater operation 4.1 Gas operation (i) Ensure that the water heater has been filled with water and that the outside flue cover has been removed. (ii) Using the Ultrastore control knob, turn the dial to the desired temperature setting then turn the outer ring to the flame position. (iii) Once the Ultrastore is switched on a green light is visible within the switch and the unit will now try and ignite. (iv) If within approximately 10 seconds, the Ultrastore fails to ignite then a red failure light will also appear. If this happens wait 30 seconds before trying again. 230V Operation (i) Simply depress the Electrical switch fitted next to the gas control to the 230V position. This will turn on the water heaters electrical element. It is imperative that there is water in the heater whenever the Gas or Electric is switched on. to operate. (iv) If the heater fails to ignite please wait 20 seconds for trying again. Electric control 5 Space Heater Operation 5.1 Gas Operation (i) Turn the gas control on top of the heater to the desired setting and depress the knob. (ii) Keeping the control knob depressed look into the viewing window and see if the gas ignites. If you have an automatic ignitor then you should hear it ticking and eventually see the pilot light. If however you have piezo ignition then you will have to manually depress the ignitor repeatedly until you see the pilot light. (iii) Once the pilot light is lit keep the control knob depressed for a further 20 seconds to allow the thermocouple Gas Control 5.3 Fan Operation The blown air function of the space heater is controlled by the three position switch on top of the heater. 5.2 Electric Operation (i) Simply depress the main switch on the Ultraheat control panel to the 230V position. (ii) Then set the power rating you require on the panel at either 500w 1000w or 2000w. How to Use Your Caravan’s Equipment 9 Explorer Group 2007 Touring Caravan Handbook Fan Control (i) Position 0 is off (ii) Position A operates the fan in automatic mode. In this position the 39 9 How to Use Your Caravan’s Equipment fan will only run when there is sufficient heat to require the air to be circulated. (iii) The third Position will operate the fan at all times. (iv) The speed of the fan is controlled by the number position set with 5 being the fastest speed and 1 being the lowest. 6 Microwave (where fitted) (i) Ensure that your microwave plug is securely inserted into the 3 pin 230V socket fitted to the left hand side of the microwave. (ii) Set the required power setting on the bottom dial from anywhere between low and high as required for the item you are cooking. (iii) Then set the timer to the required time period. (iv) Once the time has elapsed the timer bell will ring to alert you to the end of the set cooking period. (v) It is advisable to remove the plug from the socket when the microwave is not in use to prevent any inadvertent use of the microwave. 40 7 Battery Charger The battery charger for the caravan battery will automatically switch on when the caravan is connected to a mains supply. The battery charger will also provide a 12V supply to the caravan when a battery is not connected. Please note that the battery charger fitted is designed to keep your battery charged and is not designed for charging up a flat battery. 8 Smoke Detector The caravan smoke detector will become active once the 9V battery which should be supplied with the smoke detector is connected. The smoke detector fitted to your caravan has an alarm pause mode which will reduce the sensitivity of the alarm for a short period to allow for cooking within the caravan. The alarm pause mode is activated by pressing the button marked HUSH on the smoke detector. While the detector is in the pause mode the detector will beep once per minute to alert that the alarm pause mode is activated. 9 Air Conditioning Blizzard 1500 Air Conditioning Unit (Where Fitted) Starting and Function Selection (i) Internal temperature control thermostat. (ii) Two speed fan switch. (iii) ON button (push to ON position). (iv) To increase the cooling from the unit, turn the red/blue control knob to the blue section. To reduce the cool air, turn towards the red sector. (v) Push button ‘3’ to switch OFF (release to OFF position). (vi) To adjust airflow direction pull down the front brown vent from a small flap located in its centre. ATTENTION Never obstruct the air inlets and outlets. The air conditioning compressor runs during the refrigerating phase, if switched on and off at once it may get damaged. Therefore it is very important to wait at least 3 minutes before attempting to switch it on again. WARNING Never place your hands or other objects within the air inlet openings 10 Thetford cassette toilet Your caravan is fitted with a cassette toilet. 10.1 Preparing the Toilet For Use (i) Open the access door on the outside of your caravan. (ii) Rotate the waste tank emptying spout 90 degrees and remove the water filling extension (you will find it positioned beneath the handle closest to the emptying spout). (iii) Rotate the water fill funnel outwards, remove the cap and place the extension on the water fill funnel. Add the stated amount of Thetford fresh water additive to the water tank. This ensures a better and cleaner flush and keeps the water in the flush tank fresh. (iv) Fill the water tank with clean water. Warning: keep water level below the top of the water filling funnel. (v) Remove the extension and return to its original position on the waste tank. Please Note: Depending on the space between the door and waste tank, this extension part may also be fixed on the door with a hook. (vi) Screw the cap back onto the water filling funnel and push back inwards towards the side of the flush water tank. Please Note: 150 ml of water will remain in the water fill funnel when the water tank is empty. 10.2 Emptying the Toilet (i) Open outer locker door and release bottom or base catch securing cassette. (ii) Remove cassette, ensuring the flap is in the closed position (it is useful to use a trolley for taking waste tanks to the disposal point). (iii) Take the cassette to a chemical toilet waste disposal point, remove cap and place safely away from emptying point. (iv) Press air release button near handle before you tilt the tank to empty contents. (v) Rinse well and then leave some water in and replace cap. (vi) When you get back to your caravan, add chemical solution as How to Use Your Caravan’s Equipment 9 Explorer Group 2007 Touring Caravan Handbook 41 9 How to Use Your Caravan’s Equipment rooflight is held by the two gas springs after approx. 150mm). (iii) Swivel the metal bar towards the rooflight and snap into its holder. (iv) To close the rooflight, proceed with steps (i-iii) in reverse order. instructed. Replace cap and fold arm away. (vii) Slide back into locker until catch locks. (viii) Close and lock door. For further information please refer to the appliance instructions supplied in your owners information pack. 11 Rooflights Your caravan is fitted with at least one type of the following roof lights. 11.1 The Omivent (12v) Rooflight The Omivent is a double-glazed roof light constructed from a synthetic ultra-violet screened material. Its sideoperating mechanism allows a completely free central opening with built-in fixed ventilation when closed. It operates as an extractor fan and air intake fan. Please note: Do not change the direction of the fan unless it has been switched off ‘O’ position and the blades have stopped rotating. 42 11.2 The Heki 2 & Heki Duette Luxus Rooflight 11.2.1 To open to the tilted position: (i) Press the knob in the toggle catches on either side of the rooflight and turn through approx. 90°. (ii) Grasp the metal bar in the middle, snap it out of its holder, swivel down and press the rooflight upwards. (The 11.2.2 To open in the intermediate position: (i) Open the toggle catches on either side of the rooflight (see 1a). (ii) Grasp the metal bar in the middle; snap it out of its holder, swivel down and press the rooflight outwards. (Rooflight is opened automatically after approx. 150mm by the two gas springs.) (iii) Open both fasteners and swivel the metal strap toward the intermediate position and pull the rooflight down until the metal strap is stopped by the fasteners. (iv) To close, proceed with steps (i-iii) in reverse order. 11.2.3 To open in the ventilation position: (i) Open the toggle catches on either side of the rooflight (see 11.2.1 - (i)). (ii) Using both hands on the two toggle catches, press the rooflight up about 2cm and fasten the toggle catches in the corresponding setting. (iii) To close, proceed with steps (i-iii) in reverse order. 11.2.4 Closing the blinds: (i) Take hold of the end rod (without rocker) in the recessed grip and engage in the opposite end rod (with rocker). (ii) Select the required position (blackout/flyscreen) by moving both joined end rods together. CAUTION In extremely bright sunshine, the blackout blind must only be closed two-thirds and the rooflight must be set in the continuous airing position. 11.2.5 Opening the Blinds: (i) Move blind (end rod with rocker) right to the outside. (ii) Hold the recessed grip with one hand; with the other hand, press the rocker and move the blind back (do not let it recoil). operation is similar to that of the Midi Heki Roof light. CAUTION • Do not stand on the acrylic rooflight. • Close HEKI 2 completely before moving off. • Do not leave your caravan when HEKI 2 is open. • Please consult your supplying dealer if you have any problems or defects. • Remove any snow/ice or dirt before opening the roof. • Do not open when it rains or when there is a strong wind. 11.5 Standard MPK Rooflight The MPK 400 x 400 rooflight is generally fitted in washroom areas. (i) Lowering the flyscreen then pressing the black control rod in towards the centre of the rooflight. (ii) Then while the rods are depressed, push upwards to open the rooflight. 11.3 Midi Heki Rooflight (i) To open, push the large central button. (ii) Whilst depressed, slide the bar to the desired position and locate into the stops provided. 11.4 Mini Heki The Mini Heki roof light will generally be fitted in washroom areas. The 12 Windows Your caravan will be fitted with either Polyplastic; Seitz framed windows, or a mixture of both. How to Use Your Caravan’s Equipment 9 Explorer Group 2007 Touring Caravan Handbook 12.1 Polyplastic Window Opening (i) In order to open the Polyplastic window it is only necessary to move the catch upwards and release the catch from the backing plate. (ii) The Polyplastic window should remain in the open position once opened, however if it does not then tighten the friction control on the window stays to increase the holding 43 9 How to Use Your Caravan’s Equipment force. (iii) The Polyplastic window is also fitted with a night ventilation position where the catch is set to the centre position on the backing plate; in this position it may be possible for rain to enter the caravan in adverse conditions. 12.2 Seitz Window Opening (i) In order to open the Seitz window you must depress the button on the catch before moving the catch. Failure to do so will lead to the catch breaking. (ii) Seitz windows will automatically stay open once open due to the built in ratchet within the stay. (iii) In order to close the window it is necessary to open the window fully then close the window in one steady movement before closing the stays when the button should click into the locked position. 44 Keep button pushed in, then turn handle 13 Blinds & Flyscreens 13.1 Blinds (i) Pull blind down by its centre catch. Do not pull down by one side of the blind. This will inevitably lead to problems. (ii) Do not allow blinds to spring back freely. Always control them by hand. 13.2 Flyscreens (i) To operate the flyscreen, either pulls the screen fully down, fully up or across, dependant on type of window fitted, and clip into place on the blind/frame. (ii) To release, unclip from the blind/frame. If a cross bar is fitted, gently pull the crossbar downwards towards you and allow the tension of the spring to roll up the flyscreen. (iii) Where a crossbar is not fitted, disconnect from the blind catch and release gently. (iv) It is recommended that blinds are not in the closed position whilst the caravan is moving. 13.3 Door Flyscreen (If Fitted) The exterior door flyscreen can be opened or closed from both inside and outside of the caravan and does not restrict door openings. When opening or closing the door flyscreen use the finger grip provided. 14 Taps 14.1 Kitchen Taps. Your new Explorer Group caravan will be fitted with the Reich Trend mixer tap. Operation (i) For correct operation of the tap, turn the spout to the desired position over the sink. (ii) Lift the control lever to activate the pump and allow water to flow simultaneously. (iii) To adjust the temperature, swivel the lever to the left to increase the temperature and to the right to reduce the temperature. 14.2 Bathroom Taps and Showers. 14.2.1 Crusader, Rallye, Omega & Odyssey The Crusader, Rallye, Omega and Odyssey are fitted with the Reich Kama mixer tap with retractable shower. Operation The taps are operated in the same manner as the kitchen tap. 14.2.2 Avanté and Corona The Avanté and Corona caravan will be fitted with either the Whale Elegance tap and shower combination tap or a separate Whale Elegance tap and Whale Elegance shower unit. Operation These taps are operated by turning the separate hot and cold taps. To get the desired water temperatures turn on both hot and cold taps. Please Note: When only the hot water tap is turned the water temperature could be very hot. CAUTION The water temperature could be very high so do not lift the lever with the tap turned to the full left position. How to Use Your Caravan’s Equipment 9 Explorer Group 2007 Touring Caravan Handbook 15 Exterior Doors Retainers The door retainer fitted to your Explorer Group caravan is operated by simply lightly pushing the door to the side of the caravan. The retainer should automatically engage and hold the door in place. To release the door simply pull the level located on the side of the retainer towards the door and the retainer will release the door enabling it to be closed. 45 9 How to Use Your Caravan’s Equipment 16 Gas Locker Door 16.1 Avanté and Corona Models All Avanté and Corona models are fitted with holding brackets for the gas locker door. When the door is left in the open position the bracket must be used to retain the door and prevent any chance of the door falling shut. 16.2 Odyssey / Omega / Crusader / Rallye and Buccaneer models All other caravan models are fitted with a gas strut supported door which will remain in the open position without the need for a holding bracket. This door will remain open unless locked by the key. do not push the door past the vertical position as this could damages the hinges. Also care should be taken when leaving the door in the open position to ensure that any wind cannot catch the door and push it open beyond the vertical position. 17 Internal Doors 17.1 Toilet/Shower Room Doors Toilet/shower room doors are fitted with a level lock, which is operated by pushing the lever down. The level is spring-loaded and will return to the closed position upon release. It is recommend that the lever is always used when the closing the door. Toilet/Shower Room Doors. Please Note: It is important when raising your gas locker door that you 46 17.2 Other Internal Doors Other internal doors such as the wardrobe and table storage locker are fitted with a 2-position button lock. Push the button to lock the door and the button should remain flush with the door. Push the button again to release and the button should then protrude from the door surface. Other Internal Doors 18 Magnetic Catches Magnetic catches work on contact with the metal plate on the rear of the door. Simply close the door until the magnet engages and holds the metal plate. Pulling the door towards you with a moderate force will be sufficient to disengage the magnetic catch and open the door. 20 Sliding Doors The room divider should be held in place during transit by the use of the strap with the stud fastening. When stationary, the room divider can be held shut by contact between a metal plate and magnet. 21 Bed Make Up 21.1 Parallel Lounge The two single beds can be easily converted into a double bed by pulling out the bed slats, stored beneath the chest of drawers or stored in the bed slat box at the front/end of the caravan. Arrange seat cushions appropriately. 9 How to Use Your Caravan’s Equipment Explorer Group 2007 Touring Caravan Handbook 19 Sprung Hinges Overhead lockers will use sprung hinges. These are suitably strong enough when closed to securely retain the door and prevent it from opening in transit. Pulling the handle towards you with moderate force is sufficient to open the locker door and hold it in the open position. 47 9 How to Use Your Caravan’s Equipment 21.2 L-Shape Lounge Double Bed On L-shaped layout, the bed frame is pulled out from underneath the rear facing seat. Arrange the seat cushions appropriately. Removal of sofa back rest cushions will provide single beds. 48 21.3 Bunk Beds All high level beds will take a maximum weight of 75kgs / 11 stone. When in use, the high level beds must have the bunk safety boards in place as shown in the diagram. Touring caravans are manufactured with a lightweight construction and therefore the beds are not designed to be knelt, sat or stood upon without all the bed cushions in place. 23.1 Status 315 Omni directional Aerial 22 Removable Drawer Locker To remove from the caravan first locate the two retaining straps at the bottom rear of the unit, the straps are released by pulling away and down this releases the thumb catches. The locker can now be removed for storage. To secure the unit into the caravan first place the locker into position, then feed the straps though the thumb locks, holding the strap taut push the thumb lock so that is closes on the strap. 23 TV Aerial Your new Explorer Group caravan will be fitted with either a 315 or a 530 Status TV aerial To operate your 315 omni directional TV aerial follow the procedure outlined below (i) Switch ON the power pack and the red LED will illuminate (ii) Check the gain control switch is set to the normal “NML” position (Switch up). (iii) Turn on your television set and tune in. This may be necessary at all new locations. How to Use Your Caravan’s Equipment 9 Explorer Group 2007 Touring Caravan Handbook 49 9 How to Use Your Caravan’s Equipment 23.2 Status 530 Directional Aerial To operate your 530 Directional TV aerial follow the procedure outlined below: (i) Firstly determine the approximate location of the nearest transmitter and whether the signals are horizontally or vertically polarised. For assistance ask your park operator or check other antennas in the vicinity. (ii) Loosen the mast locking collar and wall bracket and raise the antenna. Turn the mast to direct the antenna 50 towards the TV transmitter. The RED SPOT on the bottom of the mast indicates the front of the antenna. (iii) When receiving vertically polarised signals. Rotate the winder anticlockwise to cant the antenna through 90 degrees. Do not over tighten or use undue force on the winder. DO NOT cant for vertically polarised signals with the TELESCOPICES EXTENDED. (iv) Switch on the power pack and the red LED will illuminate. (v) Check the gain control switch is set to normal “NML” for use. (vi) Tune in your television into the strongest signal. You may need to adjust the direction of the mast to achieve the best picture quality. (vii) Secure by tightening the mast locking collar and wall bracket. 24 VHF Television Reception (Overseas only) (i) Extend the two telescopic antennas. (ii) Tune in your television into the strongest signal. You may need to adjust the direction of the mast to achieve the best picture quality. (iii) For fine tuning of VHF you may also need to adjust the length of the telescopic antennas. Please Note: VHF TV transmissions are only horizontally polarised. 25 FM Radio Connection For both types of aerial. The Status aerial is designed to receive FM radio when connected to a carstyle radio. (i) This will require a coaxial car radio plug, a coaxial plug and a length of coaxial cable, which are available from your local caravan retailer. (ii) Assemble the cable and plugs and route the cable from the power pack to the radio. (i) Insert the plug into the back of the radio and into the TV-FM socket of the power pack. If your caravan is fitted with a factory fitted radio a AM/FM aerial will already be connected to the radio and fitted to the side of the caravan. Please Note: For information on the Entertainment equipment provided in your caravan please refer to the instruction manuals provided in your Owners information pack. 26 BPW Nose Weight Indicator Jockey Wheel The indicator, which is an integral part of the jockey wheel, will give an estimate of the noseweight of the caravan The measured value, maximum 125 kg, corresponds approximately to the supporting load of the ball coupling. (iii) The jockey wheel is only extended up to 70 mm. (iv) The wheel of the jockey wheel is showing to the rear of the caravan. 9 How to Use Your Caravan’s Equipment Explorer Group 2007 Touring Caravan Handbook For a measurement please ensure that: (i) The caravan is standing on a horizontal ground. (ii) The caravan is standing horizontally, corresponding to a distance between the lower edge of the ball coupling and the ground of approx. 390 – 420 mm. 51 10 Security SECURITY quickly identified. Theft deterrent, prevention and security of your touring caravan is taken very seriously at The Explorer Group. That is why we have provided a combination of standard features and optional extras designed to deter and prevent thieves from stealing your property. And in the unlikely event that they should succeed, aid the identification, speedy recovery of your property and assist in the prosecution of the thief. You can Microdot all kinds of property against theft including your touring caravan, motor vehicles, televisions, bicycles, jewellery, in fact anything of value to you, that will also be of value to a thief. Caravan Theft The theft of a caravan can occur in the most unlikely circumstances; from a motorway service area, even from an owner’s driveway. Secure all windows and doors when your caravan is unoccupied, even if only for a short length of time. 52 1 Microtag© Supplied as standard with every Explorer Group touring caravan, Microtag© is an innovative and technologically advanced property tracing system that can be easily applied to all your valuables. Marking your property with Microdots not only deters theft, but will also help lead to the successful prosecution of the thief and the recovery of your stolen valuables. Why Use Microdots? – In order for the Police to successfully prosecute, it is necessary to identify the true owner of stolen property. Marking your property with Microdots is the easiest way to ensure your valuables are In the event of theft the police can locate the MicroDot by using an ultra violet light. The MicroDots are then read using a MicroDot reader, or a conventional microscope. Each MicroDot is laser etched with a free phone helpline and your own unique number which is registered on the International Security Register which is manned 24 hours a day, 365 days a year. Please consult the instructions provided inside the Microtag box. 2 Robstop WS3000 The Robstop WS3000 hitchlock is made of high-grade steel alloy with a cylinder lock. It is very simple to operate and prevents unauthorised coupling and disconnection. It also prevents dismantling of the coupling itself. The safety ball covers the ball head room of the WS3000 creating an additional means of protection (available as an optional extra or from your retailer). 3 Anti-Wind Corner Steadies The rear corner steadies on all Explorer caravans have a special cowling that allows for the precise positioning of a security bolt. Once the corner steadies are down, the bolt is put in place and padlocked. This prevents the potential thief from being able to lift the corner steadies making it extremely difficult to tow the vehicle away. Owners are advised to purchase good quality, extended loop padlocks in order to secure them. 4 CRIS – The Caravan Registration and Identification Scheme – VIN CriS is the national register of UK manufactured touring caravans and was established by the National Caravan Council (NCC) in conjunction with HPI Ltd. All Explorer caravans are recorded on the CriS database by their unique 17 digit Vehicle Identity Number (VIN). This VIN and the caravan description are recorded on the Touring Caravan Registration Document, which is sent by CriS to the caravan’s registered keeper. Make a separate note of the number to keep safe at home. CriS issues Touring Caravan Registration Documents which are the equivalent of the log books issued by the DVLA for cars – the Touring Caravan Registration Document confirms the name of the registered keeper, the VIN and full vehicle description. Security 10 Explorer Group 2007 Touring Caravan Handbook Shortly after purchasing this caravan you should receive your Touring Caravan Registration Document. It will be sent by post to your home address. 5 Window Etching & Chassis Marking 53 10 Security The VIN number is stamped onto the chassis of the touring caravan and etched onto all of the windows acting as a further deterrent. Your Touring Caravan Registration Document will include a 17 character VIN (Vehicle Identification Number), shown in the top right – hand corner. This 17 character VIN will be die- stamped into the caravan drawbar and chemically etched on up to a maximum of 10 eye level windows. To protect yourself and your touring caravan, never leave the Registration Document in the caravan. For security reasons keep it in a safe place. Spare windows stencils can be found in your owners information pack for use if you ever need to order a replacement window. If you sell the caravan please follow the instructions on the Touring Caravan Registration Document. Please Note: Your Local Police Can Obtain The Use Of A Decoder By Contacting C.R.I.S. On Telephone No. 01722 411430 Please note: If you do not receive a Touring Caravan Registration Document, lose it, or any of the details recorded are incorrect, please contact: CRIS – Dolphin House, New Street, Salisbury, Wiltshire, SP1 2TB. Telephone: 01722 411430 54 6 Electronic Tagging In conjunction with the CriS registration scheme, all Explorer touring caravans are electronically tagged during manufacture for added security and ease vehicle identification. The security tag containing the individual identity of your caravan is concealed within the caravan body and can only be read by using a special decoder. 7 Explorer Protect – Autowatch Alarm System The Explorer Protect system is fitted as standard on the Rallye, Crusader and Buccaneer range (optional extra on Omega and Odyssey, Corona and Avanté). Manufactured by Autowatch, The Explorer Protect system is designed to give years of trouble free operation. Made with only the highest quality components and using state of the art technology you can be assured that your caravan has the best electronic protection available. See section below for operation or consult the manufacturers instructions provided in the Owners Information Pack. 7.1 Arming the System (i) Briefly press (large) arm/disarm button. (ii) Single chirp. (iii) Awning light illuminates for 30 seconds. (iv) Settling time of 15 seconds before responding to triggers. (v) Single intermittent flash of status LED (every 2 seconds). (vi) All sensors triggered will result in siren sounding for 30 seconds, or until reset by pressing the arm/disarm button. (ii) The alarm will arm/disarm without chirps. 7.2 Disarming the System (i) Briefly press the (large) arm/disarm button. (ii) Double chirp. (iii) Awning light illuminates briefly on and off and then on again for 30 seconds. (iv) LED off. 7.6 Sensors Each caravan alarm is installed with a Passive Infrared Detector (PIR) and a leg sensor. Additional sensors can be purchased from your dealer to enhance security. 7.3 Panic Alarm (i) Press and hold the small panic button on the transmitter for two seconds. (ii) The siren will sound for thirty seconds, unless reset by pressing any of the transmitter buttons. 7.4 Emergency Disarm. Insert the touch-key briefly into the socket. The alarm will turn off. 7.5 Silent Arm and Disarm. (i) Press the small button briefly followed by a press on the arm/disarm button. 7.6.1 Passive Infra Red Sensor The wireless PIR sensor will detect movement in the caravan and transmit a radio signal to the alarm module, if the alarm is on the siren will sound. 7.6.2 Leg Sensor The leg sensor will detect the corner stabilising leg being raised or lowered and transmit a radio signal to the alarm. The leg sensor is fully sealed against dust and water and has a battery life expectancy of three years. When the battery becomes exhausted, the sensor will need to be replaced. 7.7 Enhanced Features Arming The System In “At Home” Mode. In the ‘at home’ mode, any sensor that is programmed to be isolated, such as the PIR sensor will not trigger the alarm. Other sensors, such as the leg sensor, will trigger the siren. Arm as normal followed by a second press on the arm/disarm button within 2 seconds. Normal “on” tone followed by “at home” tone indicating isolation is active. Settling time of 15 seconds before responding to triggers. Armed in the isolation mode will be indicated by a double flash intermittently of the LED. The “at home” sensors will be isolated; other sensors will trigger the siren for 30 seconds. Security 10 Explorer Group 2007 Touring Caravan Handbook 7.8 Arming the System in Test Or Buzz Mode In the buzz mode the siren will sound a short tone when a sensor is triggered instead of sounding for 30 seconds. It is advisable to test all the sensors. 55 11 Care of Your Caravan CARE OF YOUR CARAVAN This section of the guide is devoted to the care, cleaning and general preservation of your caravan in order to retain its showroom condition. 1 Exterior Cleaning Under no circumstances should an abrasive or harsh cleaner be used. Do not use a pressure wash as this can disturb mastic seals. Exterior painted body parts of the caravan (usually the side walls) are acrylic finished aluminium, which is extremely durable and easy to clean. It is recommended you first wash off any heavy dirt and mud with cold water then use a proprietary brand wash and wax shampoo and rinse with plenty of cold water. 2 Glass Fibre Reinforced Plastic (GRP) GRP components need to be washed, waxed and taken care of like a car. Chemicals and dirt can collect during storage, and the gel coat can be 56 stained or marked when chemicals combine with rain or dew. Most stains or marks can be removed with mild dishwashing detergent, but more stubborn marks may require a (fine grit) rubbing compound such as Tcut. To help keep your GRP components looking almost like new, it is wise to wash the parts monthly (or more frequently) using mild dishwashing detergent, but avoid using strong alkaline (e.g. trisodium phosphate) or acidic cleaners or abrasives. Waxing the components once or twice a year with a good grade paste wax will help to maintain the colour and finish. 3 Acrylic Windows Your caravan is fitted with shatter resistant acrylic windows. To preserve their clarity and unblemished transparency it is essential that the following cleaning instructions are strictly adhered to: Road grit, dust, sand, flies, lime tree secretions, bird droppings etc., should be washed off using plenty of cold water do not use a sponge to clean off heavy dirt deposits. Any remaining dirt should be washed off using a soft cloth and warm water. Please Note: Under NO circumstances should any abrasive cleaning agents, household detergents or proprietary cleaning fluids be used. Wash the window again using only cold water and dry off with chamois leather. Please Note: Should scratches appear on the acrylic windows these can often be removed with an acrylic polish, i.e. ICI Perspex polish. Gentle polishing with a liquid metal polish, i.e. Brasso may also have the desired effect – consult your retailer BEFORE attempting to remove any but the slightest scratch. 4 Care Instructions for Seitz Windows Use soap suds and plenty of water or Seitz special cleaning agents to wash the acrylic window. Use talcum powder to care for the rubber seals. Only use water and mild soap suds to clean the blinds. Please Note: Do not keep the blinds closed for long periods of time, as this can result in material fatigue. 5 Care Instructions for Seitz Rooflights Clean the acrylic rooflight with soap suds and plenty of water, or use the Seitz special cleaner. Use talcum to care for the rubber seals. Only use water and mild soap suds to clean the blinds. Please Note: The 12-month guarantee becomes null and void if these instructions are not followed. 6 Window Blinds & Flyscreens To clean the blinds and flyscreens, moisten a soft cloth or sponge with a small amount of water and mild soap suds and gently wipe dirt off. Allow to dry before retracting, failure to due this could result in mildew forming. Winterisation/Storage Please Note: The blind/flyscreen should not be left in the down position when the caravan is not in use or throughout the winter as the memory of the mechanism may be lost. 7 ABS – A Frame Cover, Wheel Spats & Panels To preserve the appearance of all ABS panels and fittings road grit, dust, sand, flies, lime tree secretions, bird droppings etc., should be washed off using plenty of cold water. Any remaining dirt should be washed off using a soft cloth and warm water. Under NO circumstances should any abrasive cleaning agents, household detergents or proprietary cleaning fluids be used. Wash the ABS material again using only cold water and dry off. 8 Interior Walls Your caravan interior walls will only require a wipe over with a damp cloth, using a mild detergent, to keep them in a ‘showroom’ condition. 9 Furniture Treat your caravan furniture as you would the furniture in your home. Polish wood surfaces sparingly with a good quality wax or spray polish. Use a damp cloth to clean melanate laminated surfaces. Care of Your Caravan 11 Explorer Group 2007 Touring Caravan Handbook 10 Cooking Equipment Caustic pastes, abrasive cleaning powders, coarse wire wool and hard implements will damage the surface. 11 Carpets, Upholstery and Curtains Vacuum clean carpets and upholstery to ensure a long life, marks on cushions can be removed using a mild upholstery shampoo with the minimum of water. Curtains should be dry cleaned only. 57 11 Care of Your Caravan WARNING Under no circumstances should alcohol, spirit or solvent-based liquids be used on GRP or ABS plastic panels as these substances may react with the material and cause visible damage. 12 Shower Trays, Shower Room and Wash Basin Fittings Only clean your shower tray using soap and water. Do not use chemical based cleaning agents as this may attack the material of the tray. 13 Water System 13.1 Truma Ultraflow and Ultraflow Compact Housing - Routine Maintenance (i) Ensure that the O-ring seal on the hose plug and socket are free from dirt. (ii) To aid fitting of the plug assembly smear the O-ring with vegetable oil. (iii) To change the filter, turn the filter cap anti-clockwise and pull out the filter. 58 (iv) After installation, please drain off the first liters until the filtrate is clear. Please Note: Maximum filtering efficiency (cleaning effect) can only be achieved if the filter is changed at regular intervals. The filter must be changed within 35 days of initial use, even if it was not in use during this time. Please remember that water is a foodstuff. We recommend that filtered water is consumed within 1 – 2 days and advise you to drain the system after long periods of disuse. Use dial on the filter housing for guidance to replace after approx. 35 days of use. Please Note: Never allow the pump to run dry. Always ensure that the pump is submerged in the water or the lifetime of the pump will be reduced. 13.2 Winter Storage Before winter storage the water system must be completely drained and the filter cartridge removed. Also recharge the pump assembly or the blanking plug. If you use the Truma external shower (optional) and have therefore installed the connector”, please drain the filter housing by connecting up the outside shower and allowing the remaining water to drain via the open shower head. The filter hole may be sealed with the filter cap. 13.3 How To Prepare Your Water System For Winter Use During winter use it is recommended to keep the water container within the caravan to prevent freezing. This can be achieved by fitting an Ultraflow Compact Housing unit inside the caravan in a location where it is convenient to store a container, e.g. the washroom or under the sink etc. Special instructions are supplied with the Ultraflow winter kit. During the winter when the caravan or motor home is not in use, it is advisable to remove the filter to avoid any retained water within the filter freezing. Winter Conversion Kit (white) Truma Part no. 46060-01 Winter Conversion Kit (ivory) Truma Part no. 46060-02 15 Cleaning of all Taps It is recommended that a non-abrasive damp cloth be used for cleaning the Elegance taps and showers. 14 Compact or Filter system Accessories - Ultraflow Water Pump Assembly The Water Pump Assembly comes complete with the water pump, container cover and storage clip. The submersible pump needs no priming and is extremely quiet in operation. This pump can be used with both the Ultraflow Filter Housing and the Ultraflow Compact Housing. Standard pump assembly (hose length 800 mm) Truma Part no. 46040-01 Care of Your Caravan 11 Explorer Group 2007 Touring Caravan Handbook 16 Water Containers (i) All water remaining in any water container should be disposed of so that the container is empty. (ii) The outside of external water contains should be thoroughly cleansed and washed down to remove any dirt, dust or other contaminant. Water at a suitably hot temperature containing an appropriate detergent is recommended for this purpose. Water should then be put into the container, swirled round, then emptied out. (iii) All containers should then be totally filled with water containing an appropriate disinfectant / sterilizing solution and allowed to stand for the 59 11 Care of Your Caravan recommended contact time (e.g. Milton for 15 minutes). (iv) The solution should be emptied from the container. (v) The opening of the any container should be cleaned thoroughly with an appropriate pre-prepared wipe impregnated with a disinfectant / sterilizing solution. (vi) External containers should be inverted whilst stored overnight (if possible). (vii) Containers must be filled with mains water only and mains water only should be used for the above cleaning procedure. (viii) On no account should garden hoses be used to fill water tanks. 17 Water Systems – Sterilization Clean the water system at the start and end of the season with sterilizing fluid. When cleaning it is advisable to use a sterilizing fluid e.g. Chempro SDP or similar. Please Note: It is recommended that for this operation the filter is removed 60 as the fluid reduces the effectiveness of a new filter. (i) Drain down the system. (Open all taps to allow air in, enabling the system to drain quickly.) See Index – Draining Down The Water System. (ii) Remove any water filters fitted, and replace with a short length of hose or empty filter cartridge (this will ensure the filter is not affected by the disinfectant / sterilizing solution). (i) Fill the system by using the pump with a disinfectant / sterilizing solution. (Check that the solution at full strength appears at all taps/showers). Allow to stand for the recommended period of time. (ii) Drain the system down completely. (iii) Thoroughly clean the outside of all taps/connectors with a cloth soaked in the disinfectant / sterilizing solution. (iv) Flush the system through with clean drinking water until no traces of disinfectant / sterilizing solution can be detected at any tap. (vii)After sterilizing the system at the start of the season it is recommended that a new Ultraflow filter cartridge should be fitted. Please Note: Suitable sterilizing chemicals are available from your Explorer Group Retailer, accessory shop, chemists, or home-brew shops. It is not, however, recommended to use bleach or sodium met bisulphide. 18 Truma Space Heater Please note: Your Truma Space Heater front is now attached using 2 screws. These screws must be removed prior to removal of the Space Heater front. These screws can be seen when looking into the fire through the air vents. 19 Thetford Toilet WARNING • Cold Weather Use – to prevent freezing during cold weather use, add antifreeze to the toilet system fresh water tank. Use a 11 non-toxic (propylene glycol) type of antifreeze. Refer to chart on container to obtain level of protection. • Warmer weather or longer intervals between emptying the waste tank may require additional toilet fluid. Use only Thetford toilet fluid to achieve the best results. CAUTION • Never add toilet fluid directly into toilet bowl. • Do not use strong household detergents or cleaners that contain chlorine, solvents or acid contents. • High Altitude and Hot Weather Use – with large temperature differences and changing heights during towing, over pressure can start to build up in the waste holding tank, causing contents to splash upward upon opening the valve blade if opened too fast. Care of Your Caravan Explorer Group 2007 Touring Caravan Handbook 20 Chassis Mounted Spare Wheel Carrier Each caravan chassis has a set of punched holes immediately behind the axle to enable fitting of a spare wheel carrier. To gain access to your spare wheel lift the spare wheel carrier up and lift up the locking mechanism. Then move the mechanism to the horizontal position and the spare wheel carrier will be free to move over the mechanism and allow the spare wheel to drop to the floor to be removed. To replace the spare wheel simply reverse the operation making sure that the quick release mechanism has been fully pushed down to create a positive lock. The carrier is of extra strong, lightweight construction and zinc plated for all weather protection. It is easy to fit and accepts all conventional wheel sizes. 21 Tyres Please refer to your caravan specification sheet which is contained within this handbook for information regarding tyre pressures and axle loads. 21.1 Pressures It is customary for manufacturers to mark tyres with load and inflation data. This information relates to the use of the tyre on cars. It is dangerous to drive with under inflated tyres. The pressures (cold) recommended by the manufacturers should be regarded as a minimum. Pressure checks, including those on the spare tyre, should be made with the tyres cold and using an accurate pressure gauge. 61 11 Care of Your Caravan The checks should be carried out before each journey and at regular intervals during storage. 21.2 Tyre Wear and Damage The legal requirements for tread depth on motor vehicle tyres apply also to caravans. Similarly, it is not permitted to mix cross-ply and radial tyres on the same axle. A redundant tyre must be replaced by one of the same size and construction. Wheels should be balanced and changed round occasionally to equal wear and prolong the life of the tyres. A tyre should be renewed if a blister, rupture or cut exposing the casing is detected. If the tyre has suffered a violent impact e.g. against a kerb, it should be examined by a specialist as soon as possible. Please Note: It is customary for tyre manufacturers to mark tyres with load and inflation data. It is important to understand that this information relates only to the use of tyres on cars. 62 22 Changing a Wheel Whenever road wheels are removed and re-fitted, they must be tightened using a calibrated Torque Wrench set to 92 Nm for steel wheels and 115Nm for alloy wheels. Only use the wheel bolts supplied with you caravan. If you need to replace these bolts you should obtain bolts from an approved Explorer Group Retailer. The bolt fixings should be tightened in the sequence shown in the diagram below. Do NOT simply tighten clockwise or anti clockwise. Remember to over tighten is just as dangerous as to under-tighten, as this can distort the wheel rims. Avoid the use of power wrenches. Wheel bolts should NEVER be lubricated. The corner steadies must not be used to jack up the caravan. They can be lowered to touch the ground only as a safety measure to stabilise the caravan. (i) Apply the handbrake fully as for parking. Do not forget to give the caravan a slight rearwards push to stop the reversing lever collapsing. (ii) Slacken off the wheel bolts on the wheel to be changed. (iii) With a suitable jack, jack up the caravan under either the axle tube or the axle mounting plate. Please Note: Do Not Use The Chassis As A Jacking Point. If there is lack of ground clearance because of a flat tyre, gently move the caravan onto some ramping boards. (iv) Support the weight of the caravan with the jack and for added safety lower the front and rear corner steadies on the side of the flat tyre. Then remove the ramping boards (v) Remove the wheel bolts and remove the wheel. (vi) Before fitting the wheel, examine it for distortion or other damage. Ensure that all mating surfaces are clean and dry, including bolt/nut seats. Please Note: Always Use the Correct Bolts to Secure the Wheel – Check with the dealer if unsure. Please Note: A corner steady brace is not to be used for the next step. (vii) Insert the wheel locating pins (supplied within your Explorer Group kit box) into holes 4 and 5 and then slide the wheel onto the locating pins. (viii) Insert the wheels bolts into holes 1 then 2 and then 3. (ix) Remove the wheel locating pins from holes 4 and 5 and insert the wheel bolts. (x) After the bolts have been screwed in as far as possible by hand, each bolt should be tightened gradually in sequence. Do not over tighten at this point as the final tightening should be done with a calibrated torque wrench. The wheels of the caravan will not rotate during tightening as they are held rigid by the wheel hub brake unit. (xi) Raise the corner steadies. (xii) Lower the caravan to the ground. (xiii) The wheel bolts should be tightened ensuring that the torque is applied evenly around the wheel. Using a suitable torque wrench, sequentially tighten the steel bolts to a torque of 92Nm for steel wheels and 115Nm for alloy wheels following the sequence stated above. IMPORTANT • The torque settings should be re-checked after 50 km (20 miles) and every 5000 km (3100 miles) thereafter. • Do not loosen the wheel bolts to carry out this operation whilst the road wheel is supporting the weight of the caravan. • Wheel bolts should NEVER be lubricated. • NB: If you upgrade from steel to alloy wheels you must ensure you use the correct bolts for the new wheel. Care of Your Caravan 11 Explorer Group 2007 Touring Caravan Handbook 23 Jacking Under no circumstances should the corner steadies be used to jack up the caravan. When it is necessary to jack up, use a bottle, screw, trolley or scissor type jack, one with an axle shaped head is recommended. Place the jack plate under the axle tube as near as possible to the main longitudinal member. The maximum mass which the jockey wheel and its clamping mechanism are capable of withstanding is: 150kgs 63 11 Care of Your Caravan 24 Lubrication • Lubricate the Jockey Wheel • Lightly oil the wheel axle and screw thread. • Lubricate the Brake Linkage • Lightly oil all moving parts. • Lubricate the Corner Steadies • Lightly oil the screw and pivot pins. 25 Maintenance of your BPW Chassis The following maintenance instructions relate to the BPW chassis fitted to your Explorer Group caravan. They are a constituent part of the warranty conditions. Adhere to the relevant operating instructions of the vehicle manufacturer or of the other vehicle component manufacturers. 64 Completion of the maintenance work in accordance with the prescribed intervals is essential in order to maintain the operating safety and roadworthiness of the vehicle. The correction of any defects found or the replacement of any worn parts should be carried out by a BPW after sales service workshop, unless the vehicle user has at his disposal appropriately skilled in company workers and the necessary technical facilities. Please Note: When installing spare parts, it is strongly recommended that only original BPW components are used. Parts approved by BPW for caravan axles and suspensions regularly undergo special test procedures and as a result BPW is able to guarantee their quality. However, BPW cannot assess for every single third party product whether it can be used for BPW caravan axles and suspensions without any risk to safety. This applies even if an accredited test authority has already tested such products. Our warranty becomes null and void if spare parts other than original BPW parts are used. 25.1 Procurement of Spare Parts The code and type numbers of the axle and chassis components enable us to quickly determine your exact spares requirements when ordering from our BPW agencies and service stations. It is therefore recommended that you enter the data shown on the type plate in the following table so that it is readily available when required. The type plate or the imprint is located on the axle tube or on the housing of the towing equipment and couplings. Please Note: For full maintenance details of the BPW chassis, undergear and Winterhoff coupling please refer to the individual manufacturer’s handbook supplied within your user information pack. 12 Storage STORAGE 1 Long Term & Winter Storage If the caravan is to be stored for any length of time, especially over the winter period, the following operations are recommended: (i) Remove all linens, blankets, cushions, clothes, mattresses, etc, that could be affected by damp conditions. (ii) Clean the caravan inside and out as detailed in the previous section. (iii) Drain the water system (see Water system). (iv) For winter storage and to prevent frost damage all taps must be left in open position. For those caravans with lift up taps please ensure the taps are left in the central position. (v) Ensure all windows, roof lights and doors are correctly fastened. Check fixed ventilation apertures are not obstructed. (vi) Ensure that the refrigerator/freezer compartment doors are secured in the vent position using the door catch. 66 (vii) Check that the site you have chosen to store the caravan is open, fairly high and dry and if possible not exposed to gales etc. If this proves impossible it is recommended that the caravan chassis is anchored to the ground. (viii) Jack up the caravan (use bottle or screw jack, do NOT use the corner steadies) so that the wheels are clear of the ground. (ix) Support the caravan axle with wooden blocks, axle stands or similar so that when the jacks are removed the wheels remain clear of the ground. Lower the corner steadies to 'just' site the caravan. Cover the tyres to prevent deterioration. Release the handbrake. (x) Security: Lowering and locking the corner steadies and removing the wheels will reduce the risk of caravan theft. 2 Caravan Covers Caravan covers may be used to protect your new Explorer Group caravan provided that the cover used is of a breathable type. Ensure that the point or extending aerials on the status aerial (depending on model if fitted) are removed or retracted, and that the cover is well tied down to avoid the cover being punctured. Your caravan must be ventilated every 4 to 6 weeks if it is to be stored with a cover in place. 3 Power Drain In order to reduce any drain on your leisure battery while your caravan is being stored you should ensure that the main control switch on the refrigerator is set to the ‘0’ position Please Note: Do not work under the caravan unless the corner steadies are down and the axle is supported. Should the caravan be stored for a prolonged period of time it is strongly recommended that the caravan is fully serviced before the commencement of use. Your retailer or service centre will ensure that your caravan is safe, secure and ready for your enjoyment. Please Note: Caravans stored for any length of time should not have the handbrake or brakes applied. The wheels should be chocked or wedged and the handbrake released. The hitch head should be checked to see that it is fully extended and that there is no load on the braking system. 12 Storage Explorer Group 2007 Touring Caravan Handbook 67 13 Warranty WARRANTY 1 3-Year Manufacturer's Warranty Subject to the following conditions, your caravan is supplied with a manufacturer's warranty for 3 years from the original date of purchase, at no additional cost to you the customer. We sincerely hope you will never have cause to complain about your caravan. However, if you do have a problem then please contact your Retailer so they can report this through our warranty system. We are confident they will do their utmost to resolve any problems to your complete satisfaction. The Retailer from whom the caravan is purchased is liable for warranty repairs. Any other approved Retailer or Service Centre may carry out work at his own convenience and/or discretion, but is not obliged to do so. 2 Parts Covered By This Warranty for Years 1 - 3 Subject to the specific exclusions in years 2 and 3 set out below all original 68 components of the caravan, including permanently fitted equipment, forming part of the manufacturer's original specification. 3 Specific Exclusions for Years 2&3 Tyres, batteries, plastic windows, glass, exterior paint work, bright work and all similar trim and finish, soft furnishings, carpets and floor coverings. Entertainment/communication systems and connected equipment. Adjustment of blinds, hinges, catches, stays and doors. Replacement bulbs, fluorescent tubes, fuses and electrical connections; GRP, ABS and PVC products including A-frame covers, wheel spats and shower trays. Natural movement of internal doors and furniture. Normal wear and tear/servicing items and other components subject to routine maintenance. 4 Conditions Attached to the Warranty: (i) The duration of the warranty is 36 months from the original date of purchase. (ii) That the original construction of the caravan has not been tampered with or repaired other than by Explorer Group or an approved Retailer or Service Centre. (iii) That an "annual" service, damp and safety check has been carried out by an approved Retailer or Service Centre. The first and second services are due 60 days either side of the anniversary of the original date of purchase. The interval between services must not exceed 14 months. The third service must be on or before the anniversary date of the original purchase. (iv) That original VAT service invoices are retained as proof that annual service and inspections have been carried out. (v) No work should be commenced under the terms of the warranty unless prior authorization is obtained from The Explorer Group. (vi) Explorer Group reserves the right to inspect the caravan before any work commences. (vii) No liability will be accepted for damage caused by fair wear and tear, willful damage, negligence, abnormal working conditions, intrusion of foreign or harmful matter, overheating, freezing, failure to follow The Explorer Group instructions, misuse or alteration or repair of the caravan without The Explorer Group prior approval. (viii) Caravans covered by this warranty shall not be put out to hire, reward, or any other commercial use or used in any timed race. (ix) That the caravan shall be used only for its ordinary and intended purpose and shall not be subjected to any condition which could reasonably be foreseen to cause or result in damage or excessive wear and tear. (x) That only private cars or 4x4 type vehicles substituting as private cars, shall have towed the caravan. (xi) That no liability arises from this warranty for transport costs to and from the place of remedial work or consequential cost relating to transportation. No liability arises out of this warranty for any indirect, special or consequential loss or damage (whether for loss of profit, use, contract, goodwill, or otherwise), costs, expenses or other claims for compensation howsoever arising. (xii) No liability will be accepted for any accidental or fire damage or any loss incurred by accident or fire. (xiii) The unexpired period of the 3year warranty is transferable to second and subsequent owners during the 3year period. The new owner should contact Explorer Group within 3 months of their purchase, with proof of ownership, service history and their payment of £30 to have their details recorded in our database. of England and the parties irrevocably submit to the exclusive jurisdiction of the courts of England. Warranty 13 Explorer Group 2007 Touring Caravan Handbook Please Note: This warranty does not affect the purchaser's statutory rights. This warranty shall be governed and construed in accordance with the laws 69 14 Code of Practice - Water Ingress CODE OF PRACTICE WATER INGRESS At Explorer we want our customers to be sure that, in buying one of our caravans, you are buying the very best. We would like you to continue to believe this for a long time after you have made your purchase. We are confident that our new caravans, built with innovative manufacturing techniques and tested materials, make water ingress concerns unnecessary. We are so confident of our new caravans that we follow a 'Code of Practice' which gives certain guarantees to our customers, both consumers and Retailers, of financial reimbursement for remedial work costs should problems occur. 1 The Code The code applies to all new Explorer Group products manufactured after 1st September 1998. All owners with documentary proof of annual services by an approved 70 Explorer Group Retailer or Service Centre will be paid in full for the costs of remedial work due to water ingress. This is valid for up to 5 years from the original date of purchase of a new product. Unless the caravan has a full service history, the owner will be required to contribute to the costs of remedial work for water ingress damage depending upon the age of the caravan and work required. Each case will be examined on its own merit. Explorer will decide the amount of contribution towards the remedial work costs. Owners exchanging their current Explorer Group model for a new Explorer Group model will not have the value of their part exchange reduced due to potential water ingress issues, providing that there is documentary evidence that the caravan has been annually serviced and that it is less than 5 years old. 2 Conditions Attached To the Code (i) Work may only be undertaken after approval by Explorer (depending upon individual circumstances). (ii) Explorer will pay the costs of remedial work, only after approved work has been carried out. (iii) The Code is not retrospective. Caravans traded-in prior to implementation of the Code are not covered. 3 Customer Obligation - Servicing It is a condition of your warranty that your caravan must have an "annual" service, damp and safety check and this should be carried out by an Explorer Group approved Retailer or Service Centre, in accordance with NCC guidelines. Proof of this will be required in the event of a warranty claim. Please Note: Failure to do so will invalidate your warranty. The first service is due 60 days either side of the anniversary of the original date of purchase. The interval from purchase date to the first service and the intervals between services must not exceed 14 months. Years 3 and 5 must be on or before the anniversary date of the original purchase. Your caravan requires servicing for safety, efficiency and to protect the investment you have made. Whether the caravan is used for short trips or continental long range touring, regular servicing is necessary and will ensure continued enjoyment of your caravan. Your Retailer or Service Centre will carry out your service using the latest techniques and equipment (a list of the items to be inspected, tested and adjusted appears on the Service Vouchers in this handbook), and should provide you with the service document as proof of regular maintenance. As with motor vehicle service documents, not only will the proof of regular servicing enhance your caravan resale value, but in the unlikely event of any defect appearing at some later date - a properly serviced and documented caravan history will enable your Retailer to rapidly assess and where appropriate, carry out the necessary remedial work. 4 Mains Electrics It is recommended that you have your Mains Electrics System inspected by an NICEIC approved contractor every 3 years. 5 Spare Parts Should you require any replacement parts for your caravan it is necessary that you contact the Retailer from whom you purchased the caravan or any Explorer Group approved Retailer and give the following information, which will help in identifying the required component: (i) Model and make of caravan (ii) VIN number (iii) Description of required part (iv) Photograph, size or diagram of required part ordered and supplied through an approved retailer. 6 Remedial Work The Explorer Group together with its suppliers is continually undertaking extensive research into testing, remedial work procedures and materials such as sealants, adhesives, gaskets and tapes. Therefore, if for any reason your new caravan is damaged or requires remedial work then only an approved Explorer Group Retailer or Service Centre should undertake such work. Code of Practice - Water Ingress 14 Explorer Group 2007 Touring Caravan Handbook All such work should be undertaken using only approved Explorer Group genuine parts recommended sealant and following Explorer Group procedures. Explorer will also undertake to supply certain specialist repairers with the necessary spare parts. In this case, your selected repairer must contact the PARTS DEPARTMENT with all enquiries. Please Note: All parts must be 71 15 Caravan Construction - Main Components CARAVAN CONSTRUCTION MAIN COMPONENTS The following is a brief description of the main components used in your caravan. More comprehensive descriptions can be found in the equipment manufacturers literature held in the Owner's Information Pack. 1 BPW Chassis BPW are one of the largest producers of caravan chassis in Europe. The chassis is galvanized special steel fitted with neidhart axles and suspension system. Explorer Group Limited utilizes the new BPW V-TEC Chassis System. 2 Braking System The Braking System comprises a rod operated overrunning device with expander mechanism and adjuster box. An automatic reversing system with a spring loaded reverse lever is attached to the adjuster box. The system also incorporates a link device, which gives added safety to the 72 handbrake operation when parking on a reverse slope or steep hill. Brake adjustment instructions are given in the maintenance section of this guide. 5 Front Panel and Gas Bottle Locker Lid These are constructed from moulded GRP for strength and lightness. 3 Body Shell Caravan bodies are constructed from the highest quality materials. The fully insulated floor is constructed from a timber frame with plywood and insulation laminated together for strength. The walls comprise an insulated foam sandwich having precoated aluminium exterior surface and vinyl coated plywood interior finish. Wooden framing is positioned within the sandwich to add strength. The very latest 'state of the art' presses are employed to produce the extremely well insulated, robust, yet lightweight sections. 6 Awning Channel Each caravan is fitted, as standard, with an awning channel as an integral part of the near- and/or off-side aluminium roof and body side moulding. If it is found necessary to fit additional attachments, care must be taken to ensure that any holes which are drilled in the outside of the body are correctly sealed. Awnings which employ rubber sucker attachments rather than screw fixings are recommended. 4 Windows Windows are all of a double glazed acrylic construction and the door frames are extruded aluminium. 7 Additional Fixings to Your Caravan Shell On NO account should screw threads longer than 5/8th inch (15mm) be permitted to enter the shell sandwich (from inside). Ensure that all screws are of the self tapping type. No screw or any other object should be permitted to enter the ceiling of your new caravan. Please Note: Holes must not be drilled into the chassis. When purchasing a stabilizer, consult your retailer who will advise on the correct type to fit. 15 Caravan Construction - Main Components Explorer Group 2007 Touring Caravan Handbook 73 16 Equipment List EQUIPMENT LIST 1 Avanté & Corona Refrigerator Heater Internal blown air Water heater Sink and drainer Oven Hob Taps kitchen Shower equipment Taps vanity Water filter / pump Lights 12V fluorescent Lights 12V reading down lights Lights 230V light Control panels Electrical fittings Toilet Cassette blinds 74 Thetford N80 e Truma Ultraheat piezo New Truma push fit rapid installation Truma Ultrastore Space saving Argent stainless steel Spinflo Midi Prima Spinflo 3 burner hob Reich trend Whale white Reich Trend Truma Ultraflow Compact & Ultraflow pump Lumo & Crown Ice Zoe eyeball halogen BCA BCA PDL Thetford rotatable Seitz series 2000 2 Odyssey & Omega Refrigerator Heater Internal blown air Water heater Sink and drainer Oven Microwave Hob Taps kitchen Shower equipment Taps vanity Water filter / pump Lights 12V fluorescent Lights 12V reading down lights Lights 230V Lights 12V halogen Control panels Electrical fittings Toilet Cassette blinds Dometic RM7271 Truma Ultraheat auto New Truma push fit rapid installation Truma Ultrastore Space saving Argent stainless steel Spinflo Midi Prima BCA Spinflo 3 burner hob Reich Trend Reich chrome Reich chrome Truma Ultraflow filter & Ultraflow pump Lumo & Crown Ice Zoe eyeball halogen BCA Nova CBE CBE Thetford rotatable Seitz series 2000 Equipment List 16 Explorer Group 2007 Touring Caravan Handbook 75 16 Equipment List 3 Crusader, Rallye & Buccaneer Refrigerator Heater Internal Blown Air Water Heater Sink And Drainer Oven Microwave Hob Taps Kitchen Shower Equipment Taps Vanity Water Filter / Pump Lights 12V Fluorescent Lights 12V Reading Down Lights Lights 230V Mains Lights 12V Halogen Control Panels Electrical Fittings Toilet Cassette Blinds 76 Dometic RM7291 / 7651 Refrigerator Freezer Truma Ultraheat Auto New Truma Push Fit Rapid Installation Truma Ultrastore Space Saving Argent stainless steel Spinflo Midi Prima With Illumination & 2 Shelves BCA Spinflo 3 Burner Hob Reich Trend Reich Chrome Reich Chrome Truma Ultraflow Filter & Ultraflow pump & Waterline Lumo & Crown Ice Zoe Eyeball Halogen BCA Nova CBE CBE Thetford Rotatable With Electronic Flush Seitz Series 2000 17 Electrical Drawings ELECTRICAL DRAWINGS 1 12n & 12s Socket & Plug Wiring Diagram 12N & 12s SOCKET & PLUG WIRING DIAGRAM Red Brake Red Yellow L.H. Indicator Blue Fog L.H. Road Lights Common Earth 1 2 Black White 2 7 Green R.H. Indicator 6 3 Yellow 1 6 Black 7 5 3 4 Blue 5 White Green 4 Brake L.H. Indicator Fog L.H. Road Lights Common Earth R.H. Indicator Brown Brown 12N (Black) Car Socket 12N (Black) Caravan Plug R.H. Road Lights R.H. Road Lights View on rear of 7 pin Plug and Socket Red Fridge Red Yellow Reverse Light No connection 1 2 Black Earth/Fridge Common Earth White 6 7 Green Car Battery 6 3 5 5 Black 4 3 4 Reverse Light No connection 2 7 Fridge White Green Earth/Fridge Common Earth Car Battery Brown Brown 12S (Grey) Car Socket 12S (Grey) Caravan Plug No connection View on rear of 7 pin Plug and Socket 78 Yellow 1 No connection Avanté 17 Electrical Drawings Explorer Group 2007 Touring Caravan Handbook 79 17 Electrical Drawings Odyssey 80 Crusader 17 Electrical Drawings Explorer Group 2007 Touring Caravan Handbook 81 17 Electrical Drawings Corona 82 Omega 17 Electrical Drawings Explorer Group 2007 Touring Caravan Handbook 83 17 Electrical Drawings Rallye 84 Buccaneer 17 Electrical Drawings Explorer Group 2007 Touring Caravan Handbook 85 17 Electrical Drawings Avanté (Road Lights) 86 Odyssey (Road Lights) 17 Electrical Drawings Explorer Group 2007 Touring Caravan Handbook 87 17 Electrical Drawings Crusader (Road Lights) 88 Corona (Road Lights) 17 Electrical Drawings Explorer Group 2007 Touring Caravan Handbook 89 17 Electrical Drawings Omega (Road Lights) 90 Rallye (Road Lights) 17 Electrical Drawings Explorer Group 2007 Touring Caravan Handbook 91 17 Electrical Drawings Buccaneer (Road Lights) 92 18 Technical Specifications Avanté Model Number of Berths Interior Length Exterior body length Shipping Length Avanté 362 Avanté 482 Avanté 505 Avanté 524 Avanté 534 Avanté 544 Avanté 540 Avanté 556 2 2 5 4 4 4 4 6 Avanté 636 3683mm / 12'1" 4732mm / 15'6" 5034mm / 16'6" 5344mm / 17'6.5" 5486mm / 18'00" 5599mm / 18'5" 5526mm / 18'2" 5436mm / 17'10" 6125mm / 20'1" 4504mm / 14'9.5" 5553mm / 18'3" 5855mm / 19'2" 6165mm / 20'3" 6307mm / 20'8.5" 6429mm / 21' 6347mm / 20'10" 6257mm / 20'6.5" 6946mm / 22'9.5" 7847mm / 25'9" 6 5405mm 17'9" 6454mm / 21'2" 6756mm / 22'2" 7066mm / 23'2" 7208mm / 23'8" 6985mm / 22'11" 7248mm / 23'9" 7158mm / 23'6" Overall Width 2148mm / 7'0.5" 2148mm / 7'0.5" 2148mm / 7'0.5" 2148mm / 7'0.5" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" Overall Height 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" Maximum Headroom 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 195/70R14 96 195/70R14 96 175 R 14 99 175 R 14 99 175 R 14 99 185 R14 102P 175 R 14 99 175 R 14 99 175/65 R 14 86 Wheel Rim Tyre Size Tyre Pressure at MTPLM in psi 36 Brake Size Awning Sizes Ground to Ground Bed Sizes Bed Sizes Option 1 40 58 58 62 58 62 62 36 200/50 200/50 200/50 200/50 200/50 200/50 200/50 200/50 200/50 7930mm / 26'0" 8980mm / 29'6" 9280mm / 30'5" 9590mm / 31'5" 9730mm / 31'11" 9950mm / 32'6" 9770mm / 32'1" 9680mm / 31'9" 10370mm / 34'0" 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Double 2074 x 1332mm 1x Double 2074 x 1200mm 1x Single 2140 x 710mm 1x Single 1830 x 720mm FRONT 6'0" x 2'2.5" 6'0" x 2'2.5" 6'0" x 2'2.5" 6'0" x 2'2.5" 6'10" x 4'4" 6'10" x 3'11" 7'0" x 2'4" 6'0" x 2'4" 2 x Single 1830 x 720mm 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Single 2113 x 720mm 6'0" x 2'2.5" 6'0" x 2'2.5" 1x Single 1830 x 673mm 1x Double 1830 x 1290mm 1x Double 1830 x 1290mm 1x Single 1830 x 673mm 6'0" x 2'4" OR 6'0" x 2'2.5" 6'0" x 2'2.5" 6'0" x 4'3" 6'0" x 4'3" 6'11" x 2'4" 6'0" x 2'2.5" 1 x Double 2074 x 1420mm 1x Double 1980 x 1135mm 1x Single 1800 x 630mm 1x Double 1930 x1375mm 1x Single 1830 x 720mm 6'10" x 4'8" 6'6" x 3'9" 5'11" x 2'1" 6'4" x 4'5" 6'0" x 2'4" AND REAR 1x Single 1875 x 570mm 1x Single 1665 x 570mm 1x Single 1632 x 570mm 2 x Single 1830 x 690mm 6'2" x 1'10.5" 5'5" x 1'10.5" Option 2 5'4" x 1'10.5" 6'0" x 2'3" 2x Single 1830 x 610mm 2 x Single 1680 x 570mm 6'0" x 2'0" 5'6" x 1'10.5" 1x Double 1980 x 1420mm 1x Double 1980 x 1420mm 1x Double 1980 x 1420mm 1x Double 1980 x 1420mm 1x Double 2074 x 1420mm FRONT 6'6" x 4'8" 6'6" x 4'8" 6'6" x 4'8" 6'6" x 4'8" 6'10" x 4'8" 2 x Single 1830 x 720mm 1x Double 1980 x 1135mm 1x Single 1800 x 630mm 1x Single 1800 x 630mm 6'0" x 2'4" OR 1 x Double 2074 x 1420mm 6'6" x 3'9" 5'11" x 2'1" 5'11" x 2'1" 1x Single 1875 x 570mm 1x Single 1665 x 570mm 1x Single 1632 x 570mm 6'2" x 1'10.5" 5'5" x 1'10.5" 6'10" x 4'8" 5'4" x 1'10.5" AND REAR 2x Single 1830 x 610mm 1 x Double 2164 x 1420mm 6'0" x 2'0" 7'1" x 4'8" 2 x Single 1680 x 570mm 5'6" x 1'10.5" M.T.P.L.M. kgs 1100kgs / 21.61cwt 1265kgs /24.84cwt 1380kgs / 27.11cwt 1375kgs / 27.00cwt 1441kgs / 28.30cwt 1500kgs / 29.46cwt 1450kgs / 28.48cwt 1450kgs / 28.48cwt 1700kgs / 33.39cwt Mass in Running kgs 921kgs / 18.09cwt 1083kgs / 21.27cwt 1158kgs / 22.74cwt 1162kgs / 22.82cwt 1225kgs / 24.06cwt 1282kgs / 25.18cwt 1233kgs / 24.21cwt 1214kgs / 23.84cwt 1457kgs / 28.62cwt Essential Habitation Equipment kgs 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt Maximum User Payload kgs 181kgs / 3.56cwt 184kgs / 3.61cwt 224kgs / 4.40cwt 217kgs / 4.26cwt 219kgs / 4.30cwt 220kgs / 4.32cwt 219kgs / 4.3cwt 238kgs / 4.68cwt 245kgs / 4.81cwt Maximum Hitch Weight kgs 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt Optional Equipment Payload kgs 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt A manufacturing tolerance has been added to Mass in Running Order before calculating the Maximum User Payload. Maximum User Payload includes Essential Habitation Equipment, Personal Effects and Optional Equipment. 94 Note 1: Please take care to ensure that you have allowed for the masses of all items you intend to carry in the caravan. Note 2: Warning under no circumstances must the Technical Permissable Laden Mass of the caravan be exceeded. Note 3: All data is calculated using metric weights and measurements. The imperial figures quoted are conversions thereof. Odyssey Model Odyssey 482 Odyssey 484 Odyssey 505 Odyssey 524 Odyssey 524 L Odyssey 534 Odyssey 544 2 4 5 4 4 4 4 4828mm / 15'10" 4828mm / 15'10" 5344mm / 17'6" 5344mm / 17'6" 5344mm / 17'6" 5486mm / 18'0" 5599mm / 18'5" 5526mm / 18'2" 5660mm / 18'8" 5660mm / 18'8" 6176mm / 20'3" 6176mm / 20'3" 6176mm / 20'3" 6318mm / 20'9" 6429mm / 21' 6347mm / 20'10" Shipping Length 6550mm / 21'6" 6550mm / 21'6" 7066mm / 23'2" 7066mm / 23'2" 7066mm / 23'2" 7208mm / 23'8" 6985mm / 22'11" 7248mm / 23'9" Overall Width 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" Overall Height 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" Maximum Headroom 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 175 R14 99 175 R 14 99P 185 R14 102 185 R14 102 185 R 14 102P 185 R 14 102P 185 R 14 102P 185 R 14 102P Number of Berths Interior Length Exterior body length Wheel Rim Tyre Size 58 Tyre Pressure at MTPLM in psi Brake Size Awning Sizes Ground to Ground Bed Sizes Option 1 58 62 58 58 62 Odyssey 540 4 62 62 200/50 200/50 200/50 200/50 200/50 250/40 250/40 250/40 9075mm / 29'9" 9075mm / 29'9" 9590mm / 31'5" 9590mm / 31'5" 9590mm / 31'5" 9730mm / 31'11" 9950mm / 32'6" 9770mm / 32'1" 1x Single 1880 x 675mm 1x Double 2074 x 988mm 1x Double 2130 x 1344mm 1x Single 1880 x 675mm 1x Double 2007 x 1334mm 1x Double 2074 x 1342mm 1x Double 2074 x 1200mm 1x Single 2140 x 710mm 6'2" x 2'2" 6'10" x 3'3" 7'0" x 4'5" 6'2" x 2'2" 6'7" x 4'4" 6'10" x 4'5" 6'10" x 3'11" 7'0" x 2'4" 1x Single 1880 x 675mm 1x Double 1830 x 1290mm 1x Double 2074 x 1195mm 1x Single 1880 x 675mm 1x Single 1800 x 635mm 1x Double 1830 x 1290mm 1x Double 1830 x 1290mm 1x Single 2113 x 720mm 6'2" x 2'2" 6'0" x 4'3" 6'10" x 3'11" 6'2" x 2'2" 5'11" x 2'1" 6'0" x 4'3" 6'0" x 4'3" 6'11" x 2'4" 1x Single 1960 x 570 1 x Single 1800 x 635mm 1x Single 1655 x 570mm 1x Double 1930 x1375mm 6'5" x 1'10" 5'11" x 2'1" 5'5" x 1'10" 6'4" x 4'5" Technical Specifications 18 Explorer Group 2007 Touring Caravan Handbook 1 x Single 1655 x 570mm 5'5" x 1'10" Bed Sizes Option 2 1x Double 1984 x 1480mm 1x Double 1984 x 1480mm 6'6" x 4'10" 6'6" x 4'10" 1x Single 1800 x 635mm 5'11" x 2'1" 1x Single 1655 x 570mm 5'5" x 1'10" M.T.P.L.M. kgs 1368kgs / 26.87cwt 1425kgs / 27.99cwt 1475kgs / 28.97cwt 1495kgs / 29.36cwt 1475kgs /28.97cwt 1560kgs / 30.64cwt 1560kgs / 30.64cwt 1560kgs / 30.64cwt Mass in Running kgs 1200kgs / 23.57cwt 1237kgs / 24.29cwt 1275kgs / 25.04cwt 1302kgs / 25.57cwt 1282kgs / 25.18cwt 1365kgs / 26.81cwt 1364kgs / 26.79cwt 1365kgs / 26.81cwt Essential Habitation Equipment kgs 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt Maximum User Payload kgs 168kgs / 3.30cwt 188kgs / 3.69cwt 203kgs / 3.98cwt 194kgs / 3.81cwt 193kgs / 3.79cwt 195kgs / 3.83cwt 196kgs / 3.85cwt 195kgs / 3.83cwt Maximum Hitch Weight kgs 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt Optional Equipment Payload kgs 8kgs / 0.15cwt 8kgs / 0.15cwt 8kgs / 0.15cwt 8kgs / 0.15cwt 8kgs / 0.15cwt 8kgs / 0.15cwt 8kgs / 0.15cwt 8kgs / 0.15cwt A manufacturing tolerance has been added to Mass in Running Order before calculating the Maximum User Payload. Note 1: Please take care to ensure that you have allowed for the masses of all items you intend to carry in the caravan. Note 2: Warning under no circumstances must the Technical Permissable Laden Mass of the caravan be exceeded. Note 3: All data is calculated using metric weights and measurements. The imperial figures quoted are conversions thereof. Maximum User Payload includes Essential Habitation Equipment, Personal Effects and Optional Equipment. 95 18 Technical Specifications Crusader Model HURRICANE TYPHOON AURORA SUPER SIROCCO SIROCCO SUPER STORM STORM CYCLONE 2 4 4 4 5 6 4 4 4 4828mm / 15'10" 5344mm / 17'6" 5526mm / 18'2" 6325mm / 20'9" 6325mm / 20'9" 6325mm / 20'9" 6325mm / 20'9" 6325mm / 20'9" 6325mm / 20'9" 5660mm / 18'8" 6176mm / 20'3" 6347mm / 20'8" 6998mm / 23' 6998mm / 23' 6998mm / 23' 6998mm / 23' 6998mm / 23' 6998mm / 23' Shipping Length 6550mm / 21'6" 7066mm / 23'2" 7248mm / 23'9" 8049mm / 26'5" 8049mm / 26'5" 8049mm / 26'5" 8049mm / 26'5" 8049mm / 26'5" 8049mm / 26'5" Overall Width 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" Overall Height 2726mm / 8'11" 2726mm / 8'11" 2600mm / 8'6.5" 2600mm / 8'6.5" 2600mm / 8'6.5" 2600mm / 8'6.5" 2600mm / 8'6.5" 2600mm / 8'6.5" 2600mm / 8'6.5" Maximum Headroom 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 175 R14 99 185 R 14 102 185 R 14 102 175/65 R 14 86 175/65 R 14 86 175/65 R 14 86 175/65 R 14 86 175/65 R 14 86 175/65 R 14 86 Number of Berths Interior Length Exterior body length Wheel Rim Tyre Size Tyre Pressure at MTPLM in psi 58 Brake Size Awning Sizes Ground to Ground Bed Sizes Option 1 58 62 44 44 44 44 SUPER CYCLONE 44 44 200/50 200/50 250/40 200/50 200/50 200/50 200/50 200/50 200/50 9075mm / 29'9" 9590mm / 31'5" 9660mm / 31'8" 10570mm / 34'8" 10570mm / 34'8" 10570mm / 34'8" 10570mm / 34'8" 10570mm / 34'8" 10570mm / 34'8" 1x Single 1880 x 720mm 1x Single 1880 x 720mm 1x Single 2140 x 710mm 1x Double 2140 x 1344mm 1x Single 1880 x 720mm 2x Double 2140 x 1344mm 1x Single 1830 x 720mm 1x Single 1830 x 720mm 1 x Double 2140 x 1334mm 6'2" x 2'4" 6'2" x 2'4" 7'0" x 2'4" 7'0" x 4'4" 6'2" x 2'4" 7'0" x 4'4" 6'0" x 2'4" 6'0" x 2'4" 7'0" x 4'4" 1x Single 1880 x 720mm 1x Single 1880 x 720mm 1x Single 2113 x 720mm 1x Double 1830 x 1290mm 1x Single 1880 x 720mm AND 1x Single 1830 x 720mm 1x Single 1830 x 720mm 2 x singles 1906 x 790mm 6'2" x 2'4" 6'2" x 2'4" 6'11" x 2'4" 6'0" x 4'3" 6'2" x 2'4" 2x Single 1830 x 690mm 6'0" x 2'4" 6'0" x 2'4" 6'4" x 2'7" 1 x Single 1800 x 635mm 1x Double 1930 x1375mm 1x Double 2074 x 1325mm 6' x 2'3" 1x Double 1906 x 1360mm 1x Double 1843 x 1382mm 5'11" x 2'1" 6'4" x 4'5" 6'3" x 4'5" 6'1" x 4'6" 1x Double 2074 x 1430mm 6'10" x 4'4" 2x Single 1705 x 570mm 1 x Single 1655 x 570mm 1x Single 1962 x 570mm 5'7" x 1'10.5" 5'5" x 1'10" 6'5.5" x 1'10.5" OR 1x Double 2014 x 1430 6'7" x 4'8" 2x Single 1705 x 570mm 5'7" x 1'10.5" Bed Sizes Option 2 1x Double 2074 x 1480mm 1x Double 2074 x 1480mm 1x Double 2014 x 1480mm 1x Double 2074 x 1430mm 6'8" x 4'10" 6'8" x 4'10" 6'7" x 4'10" 6'8" x 4'8" 6'8" x 4'8" 1x Single 1800 x 635mm 1x Double 2074 x 1325mm 1x Double 1906 x 1360mm 1x Double 1843 x 1382mm 6'3" x 4'5" 6'1" x 4'6" 5'11" x 2'1" 6'10" x 4'4" 1x Single 1655 x 570mm 1x Single 1962 x 570mm 5'5" x 1'10" 6'5.5" x 1'10.5" M.T.P.L.M. kgs 1400kgs / 27.50cwt 1527kgs / 29.94cwt 1600kgs / 31.42cwt 1900kgs / 37.32cwt 1900kgs / 37.32cwt 1900kgs / 37.32cwt 1900kgs / 37.32cwt 1900kgs / 37.32cwt 1900kgs / 37.32cwt Mass in Running kgs 1240kgs / 24.36cwt 1342kgs / 26.36cwt 1413kgs / 27.75cwt 1630kgs / 32.01cwt 1620kgs / 31.82cwt 1610kgs / 31.62cwt 1630kgs / 32.01cwt 1630kgs / 32.01cwt 1630kgs / 32.01cwt Essential Habitation Equipment kgs 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 102kgs / 2.00cwt 102kgs / 2.00cwt 102kgs / 2.00cwt 102kgs / 2.00cwt 102kgs / 2.00cwt 102kgs / 2.00cwt Maximum User Payload kgs 160kgs / 31.42cwt 185kgs / 3.63cwt 187kgs / 3.37cwt 270kgs / 5.30cwt 280kgs / 5.50cwt 290kgs / 5.69cwt 270kgs / 5.30cwt 270kgs / 5.30cwt 270kgs / 5.30cwt Maximum Hitch Weight kgs 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt Optional Equipment Payload kgs 0 0 28kgs / 0.55cwt 28kgs / 0.55cwt 28kgs / 0.55cwt 28kgs / 0.55cwt 28kgs / 0.55cwt 28kgs / 0.55cwt 28kgs / 0.55cwt A manufacturing tolerance has been added to Mass in Running Order before calculating the Maximum User Payload. Maximum User Payload includes Essential Habitation Equipment, Personal Effects and Optional Equipment. 96 Note 1: Please take care to ensure that you have allowed for the masses of all items you intend to carry in the caravan. Note 2: Warning under no circumstances must the Technical Permissable Laden Mass of the caravan be exceeded. Note 3: All data is calculated using metric weights and measurements. The imperial figures quoted are conversions thereof. Corona Model Number of Berths Interior Length Exterior body length Shipping Length Corona 636 Corona 362 Corona 482 Corona 505 Corona 524 Corona 534 Corona 544 Corona 540 Corona 556 2 2 5 4 4 4 4 6 3683mm / 12'1" 4732mm / 15'6" 5034mm / 16'6" 5344mm / 17'6.5" 5486mm / 18'00" 5599mm / 18'5" 5526mm / 18'2" 5436mm / 17'10" 6125mm / 20'1" 4504mm / 14'9.5" 5553mm / 18'3" 5855mm / 19'2" 6165mm / 20'3" 6307mm / 20'8.5" 6429mm / 21' 6347mm / 20'10" 6257mm / 20'6.5" 6946mm / 22'9.5" 7847mm / 25'9" 6 5405mm 17'9" 6454mm / 21'2" 6756mm / 22'2" 7066mm / 23'2" 7208mm / 23'8" 6985mm / 22'11" 7248mm / 23'9" 7158mm / 23'6" Overall Width 2148mm / 7'0.5" 2148mm / 7'0.5" 2148mm / 7'0.5" 2148mm / 7'0.5" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" Overall Height 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" Maximum Headroom 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 195/70R14 96 195/70R14 96 175 R 14 99 175 R 14 99 175 R 14 99 185 R14 102P 175 R 14 99 175 R 14 99 175/65 R 14 86 Wheel Rim Tyre Size Tyre Pressure at MTPLM in psi 36 Brake Size Awning Sizes Ground to Ground Bed Sizes Option 1 40 58 58 62 58 62 36 62 200/50 200/50 200/50 200/50 200/50 200/50 200/50 200/50 200/50 7930mm / 26'0" 8980mm / 29'6" 9280mm / 30'5" 9590mm / 31'5" 9730mm / 31'11" 9950mm / 32'6" 9770mm / 32'1" 9680mm / 31'9" 10370mm / 34'0" 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Double 2074 x 1332mm 1x Double 2074 x 1200mm 1x Single 2140 x 710mm 1x Single 1830 x 720mm FRONT 6'0" x 2'2.5" 6'0" x 2'2.5" 6'0" x 2'2.5" 6'0" x 2'2.5" 6'10" x 4'4" 6'10" x 3'11" 7'0" x 2'4" 6'0" x 2'4" 2 x Single 1830 x 720mm 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Single 2113 x 720mm 6'0" x 2'2.5" 6'0" x 2'2.5" 1x Single 1830 x 673mm 1x Double 1830 x 1290mm 1x Double 1830 x 1290mm 1x Single 1830 x 673mm 6'0" x 2'4" OR 6'0" x 2'2.5" 6'0" x 2'2.5" 6'0" x 4'3" 6'0" x 4'3" 6'11" x 2'4" 6'0" x 2'2.5" 1 x Double 2074 x 1420mm 1x Double 1980 x 1135mm 1x Single 1800 x 630mm 1x Double 1930 x1375mm 1x Single 1830 x 720mm 6'10" x 4'8" 6'6" x 3'9" 5'11" x 2'1" 6'4" x 4'5" 6'0" x 2'4" AND REAR 1x Single 1875 x 570mm 1x Single 1665 x 570mm 1x Single 1632 x 570mm 2 x Single 1830 x 690mm 6'2" x 1'10.5" 5'5" x 1'10.5" 5'4" x 1'10.5" 6'0" x 2'3" 2x Single 1830 x 610mm 2 x Single 1680 x 570mm 6'0" x 2'0" Bed Sizes Option 2 5'6" x 1'10.5" 1x Double 1980 x 1420mm 1x Double 1980 x 1420mm 1x Double 1980 x 1420mm 1x Double 1980 x 1420mm 1x Double 2074 x 1420mm FRONT 6'6" x 4'8" 6'6" x 4'8" 6'6" x 4'8" 6'6" x 4'8" 6'10" x 4'8" 2 x Single 1830 x 720mm 1x Double 1980 x 1135mm 1x Single 1800 x 630mm 1x Single 1800 x 630mm 6'0" x 2'4" OR 1 x Double 2074 x 1420mm 6'6" x 3'9" 5'11" x 2'1" 5'11" x 2'1" 1x Single 1875 x 570mm 1x Single 1665 x 570mm 1x Single 1632 x 570mm 6'2" x 1'10.5" 5'5" x 1'10.5" Technical Specifications 18 Explorer Group 2007 Touring Caravan Handbook 6'10" x 4'8" 5'4" x 1'10.5" AND REAR 2x Single 1830 x 610mm 1 x Double 2164 x 1420mm 6'0" x 2'0" 7'1" x 4'8" 2 x Single 1680 x 570mm 5'6" x 1'10.5" M.T.P.L.M. kgs 1100kgs / 21.61cwt 1265kgs /24.84cwt 1380kgs / 27.11cwt 1375kgs / 27.00cwt 1441kgs / 28.30cwt 1500kgs / 29.46cwt 1450kgs / 28.48cwt 1450kgs / 28.48cwt 1700kgs / 33.39cwt Mass in Running kgs 921kgs / 18.09cwt 1083kgs / 21.27cwt 1158kgs / 22.74cwt 1162kgs / 22.82cwt 1225kgs / 24.06cwt 1282kgs / 25.18cwt 1233kgs / 24.21cwt 1214kgs / 23.84cwt 1457kgs / 28.62cwt Essential Habitation Equipment kgs 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt Maximum User Payload kgs 181kgs / 3.56cwt 184kgs / 3.61cwt 224kgs / 4.40cwt 217kgs / 4.26cwt 219kgs / 4.30cwt 220kgs / 4.32cwt 219kgs / 4.3cwt 238kgs / 4.68cwt 245kgs / 4.81cwt Maximum Hitch Weight kgs 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt Optional Equipment Payload kgs 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt 30kgs / 0.59cwt A manufacturing tolerance has been added to Mass in Running Order before calculating the Maximum User Payload. Note 1: Please take care to ensure that you have allowed for the masses of all items you intend to carry in the caravan. Note 2: Warning under no circumstances must the Technical Permissable Laden Mass of the caravan be exceeded. Note 3: All data is calculated using metric weights and measurements. The imperial figures quoted are conversions thereof. Maximum User Payload includes Essential Habitation Equipment, Personal Effects and Optional Equipment. 97 18 Technical Specifications Omega Model Omega 482 Omega 484 Omega 505 Omega 524 Omega 524 L Omega 534 Omega 544 2 4 5 4 4 4 4 4828mm / 15'10" 4828mm / 15'10" 5344mm / 17'6" 5344mm / 17'6" 5344mm / 17'6" 5486mm / 18'0" 5599mm / 18'5" 5526mm / 18'2" 5660mm / 18'8" 5660mm / 18'8" 6176mm / 20'3" 6176mm / 20'3" 6176mm / 20'3" 6318mm / 20'9" 6429mm / 21' 6347mm / 20'10" Shipping Length 6550mm / 21'6" 6550mm / 21'6" 7066mm / 23'2" 7066mm / 23'2" 7066mm / 23'2" 7208mm / 23'8" 6985mm / 22'11" 7248mm / 23'9" Overall Width 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" Overall Height 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" Maximum Headroom 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 175 R14 99 175 R 14 99P 185 R14 102 185 R14 102 185 R 14 102P 185 R 14 102P 185 R 14 102P 185 R 14 102P Number of Berths Interior Length Exterior body length Wheel Rim Tyre Size 58 Tyre Pressure at MTPLM in psi Brake Size Awning Sizes Ground to Ground Bed Sizes Option 1 58 62 58 58 62 Omega 540 4 62 62 200/50 200/50 200/50 200/50 200/50 250/40 250/40 250/40 9075mm / 29'9" 9075mm / 29'9" 9590mm / 31'5" 9590mm / 31'5" 9590mm / 31'5" 9730mm / 31'11" 9950mm / 32'6" 9770mm / 32'1" 1x Single 1880 x 675mm 1x Double 2074 x 988mm 1x Double 2130 x 1344mm 1x Single 1880 x 675mm 1x Double 2007 x 1334mm 1x Double 2074 x 1342mm 1x Double 2074 x 1200mm 1x Single 2140 x 710mm 6'2" x 2'2" 6'10" x 3'3" 7'0" x 4'5" 6'2" x 2'2" 6'7" x 4'4" 6'10" x 4'5" 6'10" x 3'11" 7'0" x 2'4" 1x Single 1880 x 675mm 1x Double 1830 x 1290mm 1x Double 2074 x 1195mm 1x Single 1880 x 675mm 1x Single 1800 x 635mm 1x Double 1830 x 1290mm 1x Double 1830 x 1290mm 1x Single 2113 x 720mm 6'2" x 2'2" 6'0" x 4'3" 6'10" x 3'11" 6'2" x 2'2" 5'11" x 2'1" 6'0" x 4'3" 6'0" x 4'3" 6'11" x 2'4" 1x Single 1960 x 570 1 x Single 1800 x 635mm 1x Single 1655 x 570mm 1x Double 1930 x1375mm 6'5" x 1'10" 5'11" x 2'1" 5'5" x 1'10" 6'4" x 4'5" 1 x Single 1655 x 570mm 5'5" x 1'10" Bed Sizes Option 2 1x Double 1984 x 1480mm 1x Double 1984 x 1480mm 6'6" x 4'10" 6'6" x 4'10" 1x Single 1800 x 635mm 5'11" x 2'1" 1x Single 1655 x 570mm 5'5" x 1'10" M.T.P.L.M. kgs 1368kgs / 26.87cwt 1425kgs / 27.99cwt 1475kgs / 28.97cwt 1495kgs / 29.36cwt 1475kgs /28.97cwt 1560kgs / 30.64cwt 1560kgs / 30.64cwt 1560kgs / 30.64cwt Mass in Running kgs 1200kgs / 23.57cwt 1237kgs / 24.29cwt 1275kgs / 25.04cwt 1302kgs / 25.57cwt 1282kgs / 25.18cwt 1365kgs / 26.81cwt 1364kgs / 26.79cwt 1365kgs / 26.81cwt Essential Habitation Equipment kgs 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt Maximum User Payload kgs 168kgs / 3.30cwt 188kgs / 3.69cwt 203kgs / 3.98cwt 194kgs / 3.81cwt 193kgs / 3.79cwt 195kgs / 3.83cwt 196kgs / 3.85cwt 195kgs / 3.83cwt Maximum Hitch Weight kgs 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt Optional Equipment Payload kgs 8kgs / 0.15cwt 8kgs / 0.15cwt 8kgs / 0.15cwt 8kgs / 0.15cwt 8kgs / 0.15cwt 8kgs / 0.15cwt 8kgs / 0.15cwt 8kgs / 0.15cwt A manufacturing tolerance has been added to Mass in Running Order before calculating the Maximum User Payload. Maximum User Payload includes Essential Habitation Equipment, Personal Effects and Optional Equipment. 98 Note 1: Please take care to ensure that you have allowed for the masses of all items you intend to carry in the caravan. Note 2: Warning under no circumstances must the Technical Permissable Laden Mass of the caravan be exceeded. Note 3: All data is calculated using metric weights and measurements. The imperial figures quoted are conversions thereof. Rallye Model Rallye 482 Rallye 524 Rallye 540 Rallye 634 Rallye 635 Rallye 636 Rallye 640 Rallye 644 2 4 4 4 5 6 4 4 4 4828mm / 15'10" 5344mm / 17'6" 5526mm / 18'2" 6325mm / 20'9" 6325mm / 20'9" 6325mm / 20'9" 6325mm / 20'9" 6325mm / 20'9" 6325mm / 20'9" 5660mm / 18'8" 6176mm / 20'3" 6347mm / 20'8" 6998mm / 23' 6998mm / 23' 6998mm / 23' 6998mm / 23' 6998mm / 23' 6998mm / 23' Shipping Length 6550mm / 21'6" 7066mm / 23'2" 7248mm / 23'9" 8049mm / 26'5" 8049mm / 26'5" 8049mm / 26'5" 8049mm / 26'5" 8049mm / 26'5" 8049mm / 26'5" Overall Width 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" Overall Height 2726mm / 8'11" 2726mm / 8'11" 2600mm / 8'6.5" 2600mm / 8'6.5" 2600mm / 8'6.5" 2600mm / 8'6.5" 2600mm / 8'6.5" 2600mm / 8'6.5" 2600mm / 8'6.5" Maximum Headroom 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 175 R14 99 185 R 14 102 185 R 14 102 175/65 R 14 86 175/65 R 14 86 175/65 R 14 86 175/65 R 14 86 175/65 R 14 86 175/65 R 14 86 Number of Berths Interior Length Exterior body length Wheel Rim Tyre Size Tyre Pressure at MTPLM in psi 58 Brake Size Awning Sizes Ground to Ground Bed Sizes Option 1 58 62 44 44 44 44 Rallye 650 44 44 200/50 200/50 250/40 200/50 200/50 200/50 200/50 200/50 200/50 9075mm / 29'9" 9590mm / 31'5" 9660mm / 31'8" 10570mm / 34'8" 10570mm / 34'8" 10570mm / 34'8" 10570mm / 34'8" 10570mm / 34'8" 10570mm / 34'8" 1x Single 1880 x 720mm 1x Single 1880 x 720mm 1x Single 2140 x 710mm 1x Double 2140 x 1344mm 1x Single 1880 x 720mm 2x Double 2140 x 1344mm 1x Single 1830 x 720mm 1x Single 1830 x 720mm 1 x Double 2140 x 1334mm 6'2" x 2'4" 6'2" x 2'4" 7'0" x 2'4" 7'0" x 4'4" 6'2" x 2'4" 7'0" x 4'4" 6'0" x 2'4" 6'0" x 2'4" 7'0" x 4'4" 1x Single 1880 x 720mm 1x Single 1880 x 720mm 1x Single 2113 x 720mm 1x Double 1830 x 1290mm 1x Single 1880 x 720mm AND 1x Single 1830 x 720mm 1x Single 1830 x 720mm 2 x Singles 1906 x 790mm 6'2" x 2'4" 6'2" x 2'4" 6'11" x 2'4" 6'0" x 4'3" 6'2" x 2'4" 2x Single 1830 x 690mm 6'0" x 2'4" 6'0" x 2'4" 6'4" x 2'7" 1 x Single 1800 x 635mm 1x Double 1930 x1375mm 1x Double 2074 x 1325mm 6' x 2'3" 1x Double 1906 x 1360mm 1x Double 1843 x 1382mm 5'11" x 2'1" 6'4" x 4'5" 6'3" x 4'5" 6'1" x 4'6" 1x Double 2074 x 1430mm 6'10" x 4'4" 2x Single 1705 x 570mm 1 x Single 1655 x 570mm 1x Single 1962 x 570mm 5'7" x 1'10.5" 5'5" x 1'10" 6'5.5" x 1'10.5" OR Technical Specifications 18 Explorer Group 2007 Touring Caravan Handbook 1x Double 2014 x 1430 6'7" x 4'8" 2x Single 1705 x 570mm 5'7" x 1'10.5" Bed Sizes Option 2 1x Double 2074 x 1480mm 1x Double 2074 x 1480mm 1x Double 2014 x 1480mm 1x Double 2074 x 1430mm 6'8" x 4'10" 6'8" x 4'10" 6'7" x 4'10" 6'8" x 4'8" 6'8" x 4'8" 1x Single 1800 x 635mm 1x Double 2074 x 1325 1x Double 1906 x 1360mm 1x Double 1843 x 1382mm 6'3" x 4'5" 6'1" x 4'6" 5'11" x 2'1" 6'10" x 4'4" 1x Single 1655 x 570mm 1x Single 1962 x 570mm 5'5" x 1'10" 6'5.5" x 1'10.5" M.T.P.L.M. kgs 1400kgs / 27.50cwt 1527kgs / 29.94cwt 1600kgs / 31.42cwt 1900kgs / 37.32cwt 1900kgs / 37.32cwt 1900kgs / 37.32cwt 1900kgs / 37.32cwt 1900kgs / 37.32cwt 1900kgs / 37.32cwt Mass in Running kgs 1240kgs / 24.36cwt 1342kgs / 26.36cwt 1413kgs / 27.75cwt 1630kgs / 32.01cwt 1620kgs / 31.82cwt 1610kgs / 31.62cwt 1630kgs / 32.01cwt 1630kgs / 32.01cwt 1630kgs / 32.01cwt Essential Habitation Equipment kgs 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 102kgs / 2.00cwt 102kgs / 2.00cwt 102kgs / 2.00cwt 102kgs / 2.00cwt 102kgs / 2.00cwt 102kgs / 2.00cwt Maximum User Payload kgs 160kgs / 31.42cwt 185kgs / 3.63cwt 187kgs / 3.37cwt 270kgs / 5.30cwt 280kgs / 5.50cwt 290kgs / 5.69cwt 270kgs / 5.30cwt 270kgs / 5.30cwt 270kgs / 5.30cwt Maximum Hitch Weight kgs 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt Optional Equipment Payload kgs 0 0 28kgs / 0.55cwt 28kgs / 0.55cwt 28kgs / 0.55cwt 28kgs / 0.55cwt 28kgs / 0.55cwt 28kgs / 0.55cwt 28kgs / 0.55cwt A manufacturing tolerance has been added to Mass in Running Order before calculating the Maximum User Payload. Note 1: Please take care to ensure that you have allowed for the masses of all items you intend to carry in the caravan. Note 2: Warning under no circumstances must the Technical Permissable Laden Mass of the caravan be exceeded. Note 3: All data is calculated using metric weights and measurements. The imperial figures quoted are conversions thereof. Maximum User Payload includes Essential Habitation Equipment, Personal Effects and Optional Equipment. 99 18 Technical Specifications Buccaneer Model ELAN 15 CARIBBEAN ARGOSY SCHOONER CARAVEL 2 4 4 4 4 4 4828mm / 15'10" 5344mm / 17'6" 5526mm / 18'2" 6325mm / 20'9" 6325mm / 20'9" 6325mm / 20'9" 5660mm / 18'8" 6176mm / 20'3" 6347mm / 20'8" 6998mm / 23' 6998mm / 23' 6998mm / 23' Shipping Length 6550mm / 21'6" 7066mm / 23'2" 7248mm / 23'9" 8049mm / 26'5" 8049mm / 26'5" 8049mm / 26'5" Overall Width 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" Overall Height 2726mm / 8'11" 2726mm / 8'11" 2600mm / 8'6.5" 2600mm / 8'6.5" 2600mm / 8'6.5" 2600mm / 8'6.5" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 175 R 14 99 185 R 14 102 195 R 14 106 175/65 R 14 86 175/65 R 14 86 175/65 R 14 86 Number of Berths Interior Length Exterior body length Maximum Headroom Wheel Rim Tyre Size 64 Tyre Pressure at MTPLM in psi Brake Size Awning Sizes Ground to Ground Bed Sizes Option 1 64 57 38 CLIPPER 38 38 200/50 200/50 250/40 200/50 200/50 200/50 9075mm / 29'9" 9590mm / 31'5" 9660mm / 31'8" 10570mm / 34'8" 10570mm / 34'8" 10570mm / 34'8" 1x Single 1880 x 720mm 1x Single 1880 x 720mm 1x Single 2140 x 710mm 1x Double 2140 x 1344mm 1x Single 1830 x 720mm 1 x Double 2140 x 1334mm 6'2" x 2'4" 6'2" x 2'4" 7'0" x 2'4" 7'0" x 4'4" 6'0" x 2'4" 7'0" x 4'4" 1x Single 1880 x 720mm 1x Single 1880 x 720mm 1x Single 2113 x 720mm 1x Double 1830 x 1290mm 1x Single 1830 x 720mm 2 x singles 1906 x 790mm 6'2" x 2'4" 6'2" x 2'4" 6'11" x 2'4" 6'0" x 4'3" 6'0" x 2'4" 6'4" x 2'7" 1 x Single 1800 x 635mm 1x Double 1930 x1375mm 1x Double 1906 x 1360mm 5'11" x 2'1" 6'4" x 4'5" 6'3" x 4'5" 1 x Single 1655 x 570mm 5'5" x 1'10" Bed Sizes Option 2 1x Double 2074 x 1480mm 1x Double 2074 x 1430mm 1x Double 2074 x 1480mm 6'8" x 4'10" 6'8" x 4'10" 6'8" x 4'8" 1x Single 1800 x 635mm 1x Double 1906 x 1360mm 5'11" x 2'1" 6'3" x 4'5" 1x Single 1655 x 570mm 5'5" x 1'10" M.T.P.L.M. kgs 1500kgs / 29.46cwt 1650kgs / 32.41cwt 1700kgs / 33.29cwt 1900kgs / 37.32cwt 1900kgs / 37.32cwt 1900kgs / 37.32cwt Mass in Running kgs 1263kgs / 24.81cwt 1388kgs / 27.26cwt 1436kgs / 28.21cwt 1658kgs / 32.41cwt 1658kgs / 32.41cwt 1658kgs / 32.41cwt Essential Habitation Equipment kgs 102kgs / 2.00cwt 102kgs / 2.00cwt 102kgs / 2.00cwt 102kgs / 2.00cwt 102kgs / 2.00cwt 102kgs / 2.00cwt Maximum User Payload kgs 237kgs / 4,65cwt 262kgs / 5.14cwt 264kgs / 5.18cwt 242kgs / 4.75cwt 242kgs / 4.75cwt 242kgs / 4.75cwt Maximum Hitch Weight kgs 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt Optional Equipment Payload kgs 28kgs / 0.55cwt 28kgs / 0.55cwt 28kgs / 0.55cwt 0 0 0 A manufacturing tolerance has been added to Mass in Running Order before calculating the Maximum User Payload. Maximum User Payload includes Essential Habitation Equipment, Personal Effects and Optional Equipment. 100 Note 1: Please take care to ensure that you have allowed for the masses of all items you intend to carry in the caravan. Note 2: Warning under no circumstances must the Technical Permissable Laden Mass of the caravan be exceeded. Note 3: All data is calculated using metric weights and measurements. The imperial figures quoted are conversions thereof. Avanté / Corona Specials Model Number of Berths Interior Length Exterior body length Shipping Length Avanté 362 Avanté 482 Avanté 505 Avanté 524 Avanté 534 Avanté 544 Avanté 540 Avanté 556 2 2 5 4 4 4 4 6 3683mm / 12'1" 4732mm / 15'6" 5034mm / 16'6" 5344mm / 17'6.5" 5486mm / 18'00" 5599mm / 18'5" 5526mm / 18'2" 5436mm / 17'10" 6125mm / 20'1" 4504mm / 14'9.5" 5553mm / 18'3" 5855mm / 19'2" 6165mm / 20'3" 6307mm / 20'8.5" 6429mm / 21' 6347mm / 20'10" 6257mm / 20'6.5" 6946mm / 22'9.5" 7847mm / 25'9" Avanté 636 6 5405mm 17'9" 6454mm / 21'2" 6756mm / 22'2" 7066mm / 23'2" 7208mm / 23'8" 6985mm / 22'11" 7248mm / 23'9" 7158mm / 23'6" Overall Width 2148mm / 7'0.5" 2148mm / 7'0.5" 2148mm / 7'0.5" 2148mm / 7'0.5" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" Overall Height 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" Maximum Headroom 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 195/70 R 14 91 195/70 R 14 95 165 R 14 97 165 R 14 97 175 R 14 99 184 R14 102P 175 R 14 99 175 R 14 99 175/65 R 14 82 Wheel Rim Tyre Size Tyre Pressure at MTPLM in psi Awning Sizes Ground to Ground Bed Sizes 58 56 200/50 200/50 200/50 200/50 200/50 200/50 7930mm / 26'0" 8980mm / 29'6" 9280mm / 30'5" 9590mm / 31'5" 9730mm / 31'11" 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Double 2074 x 1332mm 6'0" x 2'2.5" 6'0" x 2'2.5" 6'0" x 2'2.5" 6'0" x 2'2.5" 6'10" x 4'4" 1x Single 1830 x 673mm 1x Single 1830 x 673mm 1x Single 1830 x 673mm 6'0" x 2'2.5" 6'0" x 2'2.5" 32 Brake Size Option 1 39 62 61 61 32 61 200/50 200/50 200/50 9770mm / 32'1" 9680mm / 31'9" 10370mm / 34'0" 1x Double 2074 x 1200mm 1x Single 2140 x 710mm 1x Single 1830 x 720mm FRONT 6'10" x 3'11" 7'0" x 2'4" 6'0" x 2'4" 2 x Single 1830 x 720mm 1x Single 2113 x 720mm 1x Single 1830 x 673mm 1x Double 1830 x 1290mm 1x Double 1830 x 1290mm 1x Single 1830 x 673mm 6'0" x 2'4" OR 6'0" x 2'2.5" 6'0" x 2'2.5" 6'0" x 4'3" 6'0" x 4'3" 6'11" x 2'4" 6'0" x 2'2.5" 1 x Double 2074 x 1420mm 1x Double 1980 x 1135mm 1x Single 1800 x 630mm 1x Double 1930 x1375mm 1x Single 1830 x 720mm 6'10" x 4'8" 6'6" x 3'9" 5'11" x 2'1" 6'4" x 4'5" 6'0" x 2'4" AND REAR 1x Single 1875 x 570mm 1x Single 1665 x 570mm 1x Single 1632 x 570mm 2 x Single 1830 x 690mm 6'2" x 1'10.5" 5'5" x 1'10.5" 5'4" x 1'10.5" 6'0" x 2'3" 2x Single 1830 x 610mm 2 x Single 1680 x 570mm 6'0" x 2'0" Bed Sizes Option 2 5'6" x 1'10.5" 1x Double 1980 x 1420mm 1x Double 1980 x 1420mm 1x Double 1980 x 1420mm 1x Double 1980 x 1420mm 1x Double 2074 x 1420mm FRONT 6'6" x 4'8" 6'6" x 4'8" 6'6" x 4'8" 6'6" x 4'8" 6'10" x 4'8" 2 x Single 1830 x 720mm 1x Double 1980 x 1135mm 1x Single 1800 x 630mm 1x Single 1800 x 630mm 6'0" x 2'4" OR 1 x Double 2074 x 1420mm 6'6" x 3'9" 5'11" x 2'1" 5'11" x 2'1" 1x Single 1875 x 570mm 1x Single 1665 x 570mm 1x Single 1632 x 570mm 6'2" x 1'10.5" 5'5" x 1'10.5" Technical Specifications 18 Explorer Group 2007 Touring Caravan Handbook 6'10" x 4'8" 5'4" x 1'10.5" AND REAR 2x Single 1830 x 610mm 1 x Double 2164 x 1420mm 6'0" x 2'0" 7'1" x 4'8" 2 x Single 1680 x 570mm 5'6" x 1'10.5" M.T.P.L.M. kgs 1100kgs / 21.61cwt 1265kgs /24.84cwt 1380kgs / 27.11cwt 1375kgs / 27.00cwt 1415kgs / 27.79cwt 1500kgs / 29.46cwt 1450kgs / 28.48cwt 1450kgs / 28.48cwt 1700kgs / 33.39cwt Mass in Running kgs 951kgs / 18.68cwt 1113kgs / 21.86cwt 1188kgs / 23.33cwt 1192kgs / 23.41cwt 1228kgs / 24.12cwt 1312kgs / 25.77cwt 1263kgs / 24.81cwt 1244kgs / 24.43cwt 1487kgs / 29.21cwt Essential Habitation Equipment kgs 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt Maximum User Payload kgs 149kgs / 2.92cwt 154kgs / 3.03cwt 194kgs / 3.81cwt 187kgs / 3.67cwt 189kgs / 3.71cwt 190kgs / 3.73cwt 189kgs / 3.71cwt 208kgs / 4.08cwt 215kgs / 4.22cwt Maximum Hitch Weight kgs 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt Optional Equipment Payload kgs 0 0 0 0 0 0 0 0 0 A manufacturing tolerance has been added to Mass in Running Order before calculating the Maximum User Payload. Note 1: Please take care to ensure that you have allowed for the masses of all items you intend to carry in the caravan. Note 2: Warning under no circumstances must the Technical Permissable Laden Mass of the caravan be exceeded. Note 3: All data is calculated using metric weights and measurements. The imperial figures quoted are conversions thereof. Maximum User Payload includes Essential Habitation Equipment, Personal Effects and Optional Equipment. 101 18 Technical Specifications Odyssey / Omega Specials Model Odyssey 482 Odyssey 484 Odyssey 505 Odyssey 524 Odyssey 524 L Odyssey 534 Odyssey 544 2 4 5 4 4 4 4 4828mm / 15'10" 4828mm / 15'10" 5344mm / 17'6" 5344mm / 17'6" 5344mm / 17'6" 5486mm / 18'0" 5599mm / 18'5" 5526mm / 18'2" 5660mm / 18'8" 5660mm / 18'8" 6176mm / 20'3" 6176mm / 20'3" 6176mm / 20'3" 6318mm / 20'9" 6429mm / 21' 6347mm / 20'10" Shipping Length 6550mm / 21'6" 6550mm / 21'6" 7066mm / 23'2" 7066mm / 23'2" 7066mm / 23'2" 7208mm / 23'8" 6985mm / 22'11" 7248mm / 23'9" Overall Width 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" Overall Height 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" Maximum Headroom 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 175 R14 99 175 R 14 99P 185 R14 102 185 R14 102 185 R 14 102P 185 R 14 102P 185 R 14 102P 185 R 14 102P Number of Berths Interior Length Exterior body length Wheel Rim Tyre Size 58 Tyre Pressure at MTPLM in psi Brake Size Awning Sizes Ground to Ground Bed Sizes Option 1 58 62 58 58 62 Odyssey 540 4 62 62 200/50 200/50 200/50 200/50 200/50 250/40 250/40 250/40 9075mm / 29'9" 9075mm / 29'9" 9590mm / 31'5" 9590mm / 31'5" 9590mm / 31'5" 9730mm / 31'11" 9950mm / 32'6" 9770mm / 32'1" 1x Single 1880 x 675mm 1x Double 2074 x 988mm 1x Double 2130 x 1344mm 1x Single 1880 x 675mm 1x Double 2007 x 1334mm 1x Double 2074 x 1342mm 1x Double 2074 x 1200mm 1x Single 2140 x 710mm 6'2" x 2'2" 6'10" x 3'3" 7'0" x 4'5" 6'2" x 2'2" 6'7" x 4'4" 6'10" x 4'5" 6'10" x 3'11" 7'0" x 2'4" 1x Single 1880 x 675mm 1x Double 1830 x 1290mm 1x Double 2074 x 1195mm 1x Single 1880 x 675mm 1x Single 1800 x 635mm 1x Double 1830 x 1290mm 1x Double 1830 x 1290mm 1x Single 2113 x 720mm 6'2" x 2'2" 6'0" x 4'3" 6'10" x 3'11" 6'2" x 2'2" 5'11" x 2'1" 6'0" x 4'3" 6'0" x 4'3" 6'11" x 2'4" 1x Single 1960 x 570 1 x Single 1800 x 635mm 1x Single 1655 x 570mm 1x Double 1930 x1375mm 6'5" x 1'10" 5'11" x 2'1" 5'5" x 1'10" 6'4" x 4'5" 1 x Single 1655 x 570mm 5'5" x 1'10" Bed Sizes Option 2 1x Double 1984 x 1480mm 1x Double 1984 x 1480mm 6'6" x 4'10" 6'6" x 4'10" 1x Single 1800 x 635mm 5'11" x 2'1" 1x Single 1655 x 570mm 5'5" x 1'10" M.T.P.L.M. kgs 1368kgs / 26.87cwt 1425kgs / 27.99cwt 1475kgs / 28.97cwt 1495kgs / 29.36cwt 1475kgs /28.97cwt 1560kgs / 30.64cwt 1560kgs / 30.64cwt 1560kgs / 30.64cwt Mass in Running kgs 1208kgs / 23.73cwt 1245kgs / 24.45cwt 1283kgs / 25.20cwt 1310kgs / 25.73cwt 1290kgs / 25.14cwt 1373kgs / 26.96cwt 1372kgs / 26.95cwt 1373kgs / 26.96cwt Essential Habitation Equipment kgs 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt Maximum User Payload kgs 160kgs / 3.14cwt 180kgs / 3.54cwt 195kgs / 3.83cwt 186kgs / 3.65cwt 185kgs / 3.63cwt 187kgs / 3.67cwt 188kgs / 3.68cwt 187kgs / 3.67cwt Maximum Hitch Weight kgs 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt Optional Equipment Payload kgs 0 0 0 0 0 0 0 0 A manufacturing tolerance has been added to Mass in Running Order before calculating the Maximum User Payload. Maximum User Payload includes Essential Habitation Equipment, Personal Effects and Optional Equipment. 102 Note 1: Please take care to ensure that you have allowed for the masses of all items you intend to carry in the caravan. Note 2: Warning under no circumstances must the Technical Permissable Laden Mass of the caravan be exceeded. Note 3: All data is calculated using metric weights and measurements. The imperial figures quoted are conversions thereof. Odyssey / Omega Specials with Air Con Model Odyssey 482 Odyssey 484 Odyssey 505 Odyssey 524 Odyssey 524 L Odyssey 534 Odyssey 544 2 4 5 4 4 4 4 4828mm / 15'10" 4828mm / 15'10" 5344mm / 17'6" 5344mm / 17'6" 5344mm / 17'6" 5486mm / 18'0" 5599mm / 18'5" 5526mm / 18'2" 5660mm / 18'8" 5660mm / 18'8" 6176mm / 20'3" 6176mm / 20'3" 6176mm / 20'3" 6318mm / 20'9" 6429mm / 21' 6347mm / 20'10" Shipping Length 6550mm / 21'6" 6550mm / 21'6" 7066mm / 23'2" 7066mm / 23'2" 7066mm / 23'2" 7208mm / 23'8" 6985mm / 22'11" 7248mm / 23'9" Overall Width 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" 2286mm / 7'6" Overall Height 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" 2726mm / 8'11" Maximum Headroom 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 1908mm / 6'3" 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 5.5J x 14 175 R14 99 175 R 14 99P 185 R14 102 185 R14 102 185 R 14 102P 185 R 14 102P 185 R 14 102P 185 R 14 102P Number of Berths Interior Length Exterior body length Wheel Rim Tyre Size 58 Tyre Pressure at MTPLM in psi Brake Size Awning Sizes Ground to Ground Bed Sizes Option 1 58 62 58 58 62 Odyssey 540 4 62 62 200/50 200/50 200/50 200/50 200/50 250/40 250/40 250/40 9075mm / 29'9" 9075mm / 29'9" 9590mm / 31'5" 9590mm / 31'5" 9590mm / 31'5" 9730mm / 31'11" 9950mm / 32'6" 9770mm / 32'1" 1x Single 1880 x 675mm 1x Double 2074 x 988mm 1x Double 2130 x 1344mm 1x Single 1880 x 675mm 1x Double 2007 x 1334mm 1x Double 2074 x 1342mm 1x Double 2074 x 1200mm 1x Single 2140 x 710mm 6'2" x 2'2" 6'10" x 3'3" 7'0" x 4'5" 6'2" x 2'2" 6'7" x 4'4" 6'10" x 4'5" 6'10" x 3'11" 7'0" x 2'4" 1x Single 1880 x 675mm 1x Double 1830 x 1290mm 1x Double 2074 x 1195mm 1x Single 1880 x 675mm 1x Single 1800 x 635mm 1x Double 1830 x 1290mm 1x Double 1830 x 1290mm 1x Single 2113 x 720mm 6'2" x 2'2" 6'0" x 4'3" 6'10" x 3'11" 6'2" x 2'2" 5'11" x 2'1" 6'0" x 4'3" 6'0" x 4'3" 6'11" x 2'4" 1x Single 1960 x 570 1 x Single 1800 x 635mm 1x Single 1655 x 570mm 1x Double 1930 x1375mm 6'5" x 1'10" 5'11" x 2'1" 5'5" x 1'10" 6'4" x 4'5" Technical Specifications 18 Explorer Group 2007 Touring Caravan Handbook 1 x Single 1655 x 570mm 5'5" x 1'10" Bed Sizes Option 2 1x Double 1984 x 1480mm 1x Double 1984 x 1480mm 6'6" x 4'10" 6'6" x 4'10" 1x Single 1800 x 635mm 5'11" x 2'1" 1x Single 1655 x 570mm 5'5" x 1'10" M.T.P.L.M. kgs 1403kgs / 27.55cwt 1460kgs / 28.68cwt 1510kgs / 29.66cwt 1520kgs / 29.86cwt 1510kgs / 29.66cwt 1595kgs / 31.33cwt 1595kgs / 31.33cwt 1595kgs / 31.33cwt Mass in Running kgs 1243kgs / 24.41cwt 1280kgs / 25.14cwt 1318kgs / 25.88cwt 1345kgs / 26.42cwt 1323kgs / 26.03cwt 1408kgs / 27.65cwt 1407kgs / 27.64cwt 1408kgs / 27.65cwt Essential Habitation Equipment kgs 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt 53kgs / 1.04cwt Maximum User Payload kgs 160kgs / 3.14cwt 180kgs / 3.54cwt 195kgs / 3.83cwt 186kgs / 3.65cwt 185kgs / 3.63cwt 187kgs / 3.67cwt 188kgs / 3.68cwt 187kgs / 3.67cwt Maximum Hitch Weight kgs 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt 100kgs / 1.96cwt Optional Equipment Payload kgs 0 0 0 0 0 0 0 0 A manufacturing tolerance has been added to Mass in Running Order before calculating the Maximum User Payload. Note 1: Please take care to ensure that you have allowed for the masses of all items you intend to carry in the caravan. Note 2: Warning under no circumstances must the Technical Permissable Laden Mass of the caravan be exceeded. Note 3: All data is calculated using metric weights and measurements. The imperial figures quoted are conversions thereof. Maximum User Payload includes Essential Habitation Equipment, Personal Effects and Optional Equipment. 103 19 General Questions GENERAL QUESTIONS Q: Where Can I Obtain Your Latest Brochure? A: Our latest brochures are available from Approved Retailers or can be viewed and printed from the download section on our website www.explorer-group.co.uk. A request form can also be completed should you wish to receive a printed copy of our latest brochures. Q: Why Is the Handbook Not Specific To My Model? A: Many of the components used in the manufacture of our caravans are identical throughout our model ranges, so we produce a generic handbook, which covers all models manufactured for that season. If the literature supplied with your caravan does not answer your question then please contact your Retailer for further assistance. Q. I Require Technical Or Other Information, Who Can Help Me? 104 A. The majority of information you require is available through your Explorer Group Retailer. Q - Can You Tell Me The Second Hand Price Of My Caravan? A - As a manufacturer we are not involved in the second hand market. You should contact a Retailer, The Camping and Caravanning Club and/or The Caravan Club. They should be able to give some indication of market value. Q: How Can I Avoid Excessive Caravan Snaking When I Tow And What Should I Do If It Starts? A: The Explorer Group has extensively tested our caravans and we are confident of their stability. However, many other factors can influence your towing unit. When loading your caravan put heavy items low down and mainly over the axle(s). You should not stow tins, bottles or heavy items in overhead lockers, during towing. Everything else should be distributed evenly around your caravan, front and back, and each side of the centre line should snaking start, if at all possible don't brake and don't compensate by steering into the swings. Just ease up on the accelerator and allow your speed to gradually decrease until the snaking subsides. Q: What Is The Correct Awning Size For My Caravan? A: Ground to ground awning measurements for Explorer Group caravans can be found by looking in the latest model section, the Product Archive section on our website, or by referring to the relevant Technical Specification section of this handbook. However, we advise you verify this information by threading a piece of string through the awning channel from ground to ground, and then by measuring the string. Your awning manufacturer will then advise on the nearest size of awning appropriate for your measurement. Q: Can I Fit A Bicycle Rack/Top Box/Air Conditioning To My Caravan? A: It may be possible to fit accessories to your caravan but this will depend upon the internal construction of the roof/walls and whether they can support the weight of the accessory. If it is possible your Retailer will be able to advise you, (or alternatively they will obtain confirmation and a drawing where necessary, from The Explorer Group). Please note that weight of any accessories will reduce your User Payload allowance. Q: My Interior Lights Are Not Working, What Do I Do? A: It is possible that all of the 230V mains electrical equipment may not be operated simultaneously. Check fuses, battery connections and power supply (master light switch). Refer to your Retailer for further assistance. PLEASE NOTE: The internal lights in your caravan will not operate whilst the caravan’s electrical hitch cables are connected to a towing vehicle with the engine running. Q: Where Can I Get Spare Parts For My Caravan? A: Retailers will be able to source most parts you require. For details of your nearest Explorer Group Retailer please refer to our Find A Retailer section on our website, or call 01207 699 000 for assistance. Q. How Many Years Will Spare Parts Be Available For My Caravan? A. The Explorer Group will endeavour to supply spare parts for a caravan, for at least 8 years from new. Q. Why Don't You Stock Parts At The Explorer Group Factory? A. Due to the volume of models we produce it is not possible for us to maintain stock levels of every individual component used in our manufacturing process. We do stock commonly requested items, but some items must be made to order Q. What If The Parts Are No Longer Available? A. Where an original part is no longer available, whenever possible we will suggest a suitable alternative if it is available. A: Your supplying Retailer is obliged to undertake your warranty work. However, any approved Explorer Group Retailer or Service Centre can undertake the work, but this is at their discretion. We will also accept services completed by a NCC Jones Vening approved company, but they will not be able to undertake warranty work if they are not approved by Explorer Group. General Questions 19 Explorer Group 2007 Touring Caravan Handbook Q. I Am Having Trouble Booking My Caravan For Its Service, In Line With The Requirements. What Timescale Is Acceptable? A. We will allow a delay of 60 days after your service is due, but subsequent annual services should still be undertaken as close as possible to the anniversary of the original date 105 19 General Questions of purchase. Except for 3rd and 5th services, which must be on or before the anniversary of the original date of purchase. Q. I Have A Problem With My Caravan, Who Can Help Me? A. We would always recommend that you contact your supplying Retailer. Your local Explorer Group Retailer or Explorer Group Approved Service Centre may be able to assist. An inspection can then take place and the necessary course of action agreed. Q. I Am Unhappy With The Service I Have Received From My Retailer/Service Centre, Where Do I Go From Here? A. We would recommend that you write to your Retailer/Service Centre, detailing your problems and requirements, requesting a response explaining how they will resolve your complaint. A copy of your letter can also be forwarded to The Explorer Group Customer Services Department, quoting the serial number 106 of your caravan and the name of the Retailer/Service Centre. Please be assured that we will assist your Retailer/Service Centre in resolving any problems. 20 Glossary GLOSSARY 12N & 12S Between towing vehicle and caravan there can be one or two electrical jack plugs. The black plug and socket is called the 12N and supplies power to the caravan rear fog light, indicators, stop lights and riding lights and an earth return. The second plug and socket can be coloured white or light grey. This is called the 12S and supplies power for the caravan’s reversing lights, fridge, battery charger and interior lights and has two earth connections. Because the 12S plug is virtually a mirror image of the 12N plug the 12N plug can’t be plugged in to the 12S socket or vice a versa. A Frame This is the triangular part at the front of the caravan’s chassis which is between the main body and the hitch it is also called the drawbar. ABS Acrylonitrile Butadiene Styrene Plastic 108 the material used for most of the large plastic components within your caravan. Actual Laden Weight This is the total weight of the caravan when loaded ready for use by the end user. Aquaroll Brand name used generically for a water container that rolls so you don’t need to lift it. Awning This is a tent-like structure of fabric over a supporting framework, which can be attached to the side of caravan. Battery Charger This is required to keep a leisure battery charged. Most caravans include a charging facility which operates via the mains hook-up, and also has the ability to recharge from the tow car’s alternator while traveling. Berth(s) Sleeping place - Refers to the number of people a caravan can accommodate for sleeping. Blown Air Heating A method of heating the living quarters of a caravan by use of a fan pushing air out through a number of outlets. Breakaway Cable A thin steel cable linking the caravan handbrake to the vehicles tow bar In the event of the caravan becoming detached from the car, the cable will pull the caravan handbrake on before snapping. Bunk Bed This is a sleeping place, usually higher up than a conventional bed. Often (but not always) this can be folded or removed to provide additional living space. Butane Is a form of Liquefied Petroleum Gas (LPG) which normally comes in blue cylinders. This type of gas is most commonly used in the UK, although a switch to propane is advised in severely cold weather conditions. Calor This is the main supplier of propane (red) gas cylinders and significant seller of butane (blue) gas. Campingaz This is the trade name of Butane gas. Cassette Blind This is a roller blind which is fitted as part of the window assembly, often along with a flyscreen, thus giving a neat installation. Cassette Toilet A form of chemical toilet found in modern caravans, where the waste holding tank can be accessed and emptied from, outside. Chemical Toilet Most modern caravans have them, with more up market models having a fully plumbed-in flushing version. Control Panel Used as the description for the panel of electrical switches and gauges governing 12V and mains electricity systems. Corner Steadies The winding device built into each corner of a caravan chassis that is used to stabilise the body once set up on a pitch. Coupling Head - See hitch. CRiS This is the Caravan Registration and Identification Scheme. It is a voluntary scheme which registers caravans in a similar manner to how motor vehicles are registered. Allows you to check the legitimate right to ownership of the seller of a secondhand caravan, and helps in the recovery of stolen caravans. Dinette This is a popular style of seating arrangement where two seats or settees face each other across a table. Glossary 20 Explorer Group 2007 Touring Caravan Handbook Earth Leakage Circuit Breaker ELCB Earth leakage circuit breaker – see residual current device (RCD) ELCB Earth Leakage Circuit Breaker. More normally termed RCD. End Kitchen A common term used to describe floor plans which put the kitchen across the rear, usually adjacent to a caravan door on one side and washroom on the other. Essential Habitation Equipment Those items and fluids required for the safe and proper functioning of the equipment for habitation as defined by the manufacturer of the caravan. This includes items such as the leisure battery and gas cylinders, plus water contained in the water heater etc. 109 20 Glossary Flyscreens Mesh fittings for windows doors and roof vents, to keep out insects etc. Free-Standing Table This is a table which, because of its leg design, can be used inside or outside. Full Service Pitch This is a pitch which has individual provision for fresh water supply and waste water disposal, in addition to mains electricity and in some cases TV aerial connection. Gas Cylinder This is a portable, pressurized container for the storage at LPG. Gas Cylinder Locker Is the compartment on the caravan for the storage of gas cylinders. Gas Drop out Holes These are not Part of the ventilation. LPG is heavier than air, so holes through the floor below gas-powered 110 appliances allow any leakage of gas to exit the habitation area. Grey Water This is the waste water from sink/shower. Gross Train Weight This is also known as Combined Weight. The maximum permitted weight of an outfit as specified by the tow car manufacturer. Gross Vehicle Weight (GVW) This is the weight of the vehicle laden to its maximum, as defined by the manufacturer. See also MTPLM. GRP Is Glass-reinforced plastic, but more commonly known as glass fibre (not fibre glass, which is a trade name). Handbook This is an owner’s manual, a guide to the workings of your caravan. Hardstanding This is a pitch which has a hard surface made of gravel, asphalt, concrete etc, instead of grass. Hitch This is the mechanism which allows a caravan to be attached to a tow ball. Hitch Lock A security device that prevents the caravan hitch being used. Hook-Up This is a facility on a pitch for connection to mains electricity. Ingress Usually meaning water ingress, a possible problem where water seeps in at the joins, usually as a result of worn sealant. Jack This is a device for raising the vehicle so that a wheel can be changed, for instance. Not to be confused with corner steadies which although they are sometimes referred to as ‘corner jacks’ are steadying, not lifting devices. ensure the correct functioning of the fridge and water systems. Jockey Wheel The small front wheel attached to the caravan A-frame used to support the forward end of the caravan, when detached from the towing vehicle. LPG Liquid Petroleum Gas, i.e. butane or propane. Kerb Weight This is the empty weight of a motor vehicle as defined by the manufacturer. Layout This is the Interior design and details where furniture units are placed in relation to each other. Leisure Battery This supplies the power for the caravan electrical systems and is sometimes called an auxiliary battery. Leveling The process of ensuring that a caravan is level when sited on a pitch. It is important for comfort and also to L-Shaped This is a term where the seating area of a caravan is indeed L-shaped. Mains Hook-Up This is a campsite facility where you can plug into a mains electricity supply. Maximum Hitch Height The maximum height at which the hitch should be connected to a towing vehicle Maximum Permissible Towing Weight This is the maximum weight that the towing vehicle is allowed to tow. Maximum User Payload This is the maximum payload available for the user including essential habitional equipment. MIRO - Mass In Running Order Weight of the caravan equipped to the manufacturer’s standard specification. Therefore the condition in which it leaves the factory. Note that this does not include any part of the user payload, including the essential habitation equipment. Glossary 20 Explorer Group 2007 Touring Caravan Handbook MTPLM - Maximum Technically Permissible Laden Mass The technical maximum permissible laden weight of the caravan, this must not be exceeded. National Caravan Council The only trade association representing manufacturers, retailers and suppliers within the caravan industry. Nose weight The weight exerted on the tow bar. Special scales are available from accessory shops for measuring this weight. 111 20 Glossary Number Plate Caravans must display a legal number plate showing the same registration mark as their towing vehicle. PDI This is an inspection undertaken by the Retailer prior to handover to the customer. Optional Equipment Payload This is payload provided by Explorer for any factory fitted options that are available. Pitch A designated area of a caravan site allocated for the use of one outfit. Most sites will be arranged with defined pitches. Road Lights The external lights used while the vehicle is traveling. Roof Lights - See Roof Vent. Outfit The caravan and its towing vehicle considered as a unit. Owners’ Club This is a group of people who usually own the same brand of caravan and enjoy meeting up for rallies. Payload The amount you can put into a caravan. Specifically the difference between the Maximum Technical Permissible Laden Mass (MTPLM) and the Mass In Running Order (MIRO). 112 Propane Gas used in colder conditions and is usually supplied in red cylinders. RCD This is a residual current device and is part of the electrical system which will ‘trip’ if there is an electrical fault. Gas Regulator Safety device fitted between the gas cylinder and the gas system of a caravan, which controls the pressure of gas being released from the cylinder. Roof Vent Is an opening unit in the ceiling which lets in ventilation and light, these vary in size, but the best ones will have integral blinds and flyscreens and are also called rooflights. Semi-Rigid Pipe work Is water pipes made of a semi rigid plastic and are infinitely preferable to cheaper convoluted piping which can act as a trap for germs and smells. Single Axle This is a caravan with a single pair of wheels on one axle. See also twin axle. Slats Sometimes used for beds and can improve ventilation to mattress cushions. Space Heater This is a Type of heating equipment for the living quarters. Modern units fitted offer gas and mains-operation. Towing Limit See manufacturer’s braked towing limit and manufacturer’s unbraked towing limit. Speed Rating This is the maximum speed at which a tyre may be used, as marked on its sidewall. Towing Mirrors Additional rear vision mirrors added to a towing vehicle to provide a greater width of view to see past a caravan. Stabiliser A safety device which helps to prevent instability, this is done by increasing the friction between the caravan hitch and the tow ball. Train Weight The maximum permissible combined weight of tow car and touring caravan. Steady Winder A handle for operating the corner steadies. Torque Wrench A form of spanner used to set nuts and bolts to a specified degree of tightness. It is recommended for adjustment of wheel fixings on caravans. Twin Axle Is a caravan with two pairs of wheels, on two axles which are located close together. These are usually the larger, heavier caravans, where the second axle helps carry the greater weight more easily, and also makes a longer caravan more stable to tow. See also single axle. User Payload The weight of all items carried in the caravan. U-Shaped Settee Usually a reference to seating that literally is ‘U’ shaped. Glossary 20 Explorer Group 2007 Touring Caravan Handbook Vehicle Kerb weight The weight of the tow car often indicated in the manufacturers specifications. VIN - Vehicle Identification Number This is a unique serial identification number for a vehicle. All Cars and motor caravans should carry a VIN. Caravans are not obliged to, but most of those sold in recent years in the UK do as a result of the CRiS voluntary registration scheme. Warranty Is the terms and conditions that spell out your rights with regard to servicing, repair or replacement of parts as provided by the manufacturer. Wild Camping Term used for staying overnight away from a campsite. Illegal in many countries, but permission may be 113 20 Glossary granted by individual landowners. 114 21 2007 Explorer Group Retailer Special Editions 2007 EXPLORER GROUP RETAILER SPECIAL EDITIONS 116 PARENT MODEL RETAILER SPECIAL AVANTÉ AMBER ELUSION KNIGHTSBRIDGE QUEENSFERRY ANTIGUA/BARBADOS/TRINIDAD BERMUDA/JAMAICA/TOBAGO XSCAPE CORONA CONNOISSEUR MAGNUM MAGNUM SPORT RAMBLER ODYSSEY SUNSEEKER WISTON/ASHINGTON/ CHILTINGTON/GOODWOOD/ AMBERLEY/ARUNDEL SUNSTYLE OMEGA LIBERTE MAGNUM CLASSIC All Explorer Group retailer specials are based on our current base models. For details on the equipment fitted and how to operate them, please check under the base model details in the main part of this handbook. For example if you have purchased an Elusion then the space heater fitted will be operated in the same manner as the space heater fitted in the standard Avanté. 22 Annual Service Record SERVICE DOCUMENTS TOURING CARAVANS - ANNUAL SERVICE RECORD In order to take full use of your Explorer Group Warranty it is essential that your caravan is serviced within the time scale laid down in the warranty terms and conditions. See Index - Warranty Terms & Conditions. Whether you use your caravan for short journeys or for touring at home or abroad, regular servicing will help to ensure that you can enjoy it to the full. The Annual Service offered by your retailer will include the following work and it is our recommendation you have your caravan serviced to this standard annually, in accordance with the National Caravan Council recommendations. The retailer will complete the record in this guide to show the work has been carried out. SECTION (A) CHASSIS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Brakes Suspension Axles and Hubs Tyres and pressures Wheel nuts Towing hitch and reverse Jockey wheel Breakaway chain Corner steadies Adjusted and lubricated Fully operational SECTION (B) EXTERIOR 1. 2. 3. 4. 5. Exterior panels Windows Rooflights Entrance door/Door Locks Wheel Boxes 6. 7. 8. 9. 10. 11. 12. Mouldings Gas bottle and Fairing Ventilators Paintwork All seals, mouldings etc. Damp test Striping etc. 12. 13. 14. 15. 16. 17. 18. Cold water system Window hinges and stays Cassette Toilet Shower Shower Tray Central Heating Damp Test SECTION (C) INTERIOR SECTION (D) ELECTRICAL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 1. 2. 3. 4. 5. 6. 7. 8. 9. Walls panels Furniture Curtains/Blinds/Flyscreen Mattresses Carpet Doors and Drawers All hinges and catches Ventilators Water pumps Hoses and sink plugs Hot water system 10. Reflectors All interior lights/Road lights Water pump and switches Refrigerator Distribution Unit Charging Unit Junction Box/Strip Wiring and supports Trailer connecting plugs sockets Overall tests ext. 11. 12. 13. Awning lights Electronic Ignition (Hob) 230v System where applicable SECTION (E) GAS INSTALLATION 1. 2. 4. 5. 6. 7. Hotplate Refrigerator Heater Leak tested Water heated Fully operation SECTION (F) FINAL Road Test CARE WARRANTY Your caravan is covered by the 3 year warranty, it is a condition of this warranty that a service and safety check is carried out by your caravan retailer at least once a year (12 months from the date of purchase) in accordance with the National Caravan Council recommendations. 118 ANNUAL SERVICE RECORD CARAVAN MODEL VEHICLE IDENTIFICATION NUMBER YEAR 1st SERVICE 2nd SERVICE 3rd SERVICE DATE: DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 4th SERVICE 5th SERVICE 6th SERVICE DATE: DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. Annual Service Record 22 Explorer Group 2007 Touring Caravan Handbook 119 22 120 Annual Service Record 7th SERVICE 8th SERVICE 9th SERVICE DATE: DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 10th SERVICE 11th SERVICE 12th SERVICE DATE: DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 13th SERVICE 14th SERVICE 15th SERVICE DATE: DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. Index INDEX Description 12n & 12s Socket & Plug Wiring Diagram 12v Power Supply 12v Systems Special Editions - 2007 (Retailers) 230v Power Supply 3-Year Manufacturer's Warranty ABS – A Frame Cover, Wheel Spats & Panels - Cleaning Activating the stabiliser Additional Fixings to Your Caravan Shell Air Conditioning Alarm - Arming the System in Test or Buzz Mode Alarm - Basic Operation Arming the System Alarm - Disarming the System Alarm - Emergency Disarm. Alarm - Enhanced Features Arming The System In “At Home” Mode. Alarm - Leg Sensor Alarm - Passive Infra Red Sensor Alarm - Sensors Alarm - Silent Arm and Disarm. Annual Service Record Anti-Wind Corner Steadies Arriving On Site Avanté - Technical Specification Avanté & Corona - Equipment List Avanté & Corona -Electrical Control Panels Avanté / Corona Specials - Technical Specifications Avanté Internal Wiring Avanté Road Lights 122 Page No. 78 30 22 116 30 68 57 14 72 40 55 54 55 55 55 55 55 55 55 118 53 20 94 74 34 101 79 86 Awning Channel 72 Barbecue Point - Gas 28 Bathroom Taps and Showers (Avante and Corona) 45 Bathroom Taps and Showers (Crusader, Rallye, Omega & Odyssey) 45 Bathroom Taps and Showers. 45 Battery Charger 40 Battery Installation 30 Battery Maintenance 30 Bed Make Up 47 Before Setting Off 16 Blinds 44 Blinds & Flyscreens 44 Body Shell 72 BPW Chassis 72 BPW Nose Weight Indicator Jockey Wheel 51 Braking System 72 Breakaway Cable 15 Breakaway Cable - Checks 16 Breakaway Cable - Correct Procedure For Use 15 Breakaway Cable - Designated Attachment Point 15 Breakaway Cable - No Designated Attachment Point 16 Breakaway Cable - Other Means of Attachment 16 Buccaneer - Technical Specification 100 Buccaneer Internal Wiring 85 Buccaneer Road Lights 92 Bulb Ratings Maximum for Internal Lights 31 Bunk Beds - Bed Make Up 48 Cables 17 Caravan Construction – Main Components 72 Caravan Covers 66 Caravan Handling 18 Caravan Towing Vehicle Weight Ratio 12 Care Instructions for Seitz Rooflights 57 Care Instructions for Seitz Windows Care of Your Caravan Carpets, Upholstery and Curtains - Cleaning Cassette toilet Cassette toilet - Emptying the Toilet Cassette toilet - Preparing the Toilet for Use Changing a Wheel Charger/Generator Chassis - Maintenance of your BPW Chassis Chassis Mounted Spare Wheel Carrier Check Site Regulations Checking the stabiliser Cleaning - Acrylic Windows Cleaning - Glass Fibre Reinforced Plastic (GRP) Cleaning of all Taps Cleaning the Exterior of your Caravan Code of Practice - Conditions Attached To the Code Code of Practice - Customer Obligation - Servicing Code of Practice - Water Ingress Compact or Filter system Accessories - Ultraflow Water Pump Assembly - Cleaning Connecting To Mains Supply On Arrival at Site Contents Cooking equipment Cooking Equipment - Cleaning Corona - Technical Specification Corona Internal Wiring Corona Road Lights Correct Procedure For Use Coupling 56 56 57 41 41 41 62 22 64 61 20 14 56 56 59 56 70 70 70 59 22 1 35 57 97 82 89 15 13 CRIS – The Caravan Registration and Identification Scheme – VIN Crusader - Technical Specification Crusader Internal Wiring Crusader Road Lights Crusader, Rallye & Buccaneer - Equipment List Directional Aerial - Status 530 Disconnecting Mains Supply When Leaving Site Disengaging the stabiliser Dometic Refrigerator (Odyssey, Omega, Crusader, Rallye and Buccaneer Models) Door Flyscreen (If Fitted) Draining Down Your Water System Electrical Connection - Overseas Electrical Control Panels Electrical Control Panels - Avanté & Corona Electrical Control Panels - Odyssey, Omega, Rallye, Crusader and Buccaneer Electrical Control Panels for caravans with an onboard water tank Electrical Control Panels for caravans without a fixed water tank Electrical Drawings Electrical Drawings Electrical System Electrical System - Automatic Charging System Electrical System - Generators / Charger Electrical System - Mains Unit Electrical System - Resetting the RCD Electricity Electricity Mains Supply Electronic Tagging Equipment Lists 53 96 81 88 76 50 23 14 38 Index Explorer Group 2007 Touring Caravan Handbook 44 27 23 34 34 34 35 35 78 79 30 31 30 30 31 22 22 54 74 123 Index Explorer Protect Autowatch 650 Caravan Alarm Exterior Doors Retainers Fire - In Case Of… Fire - Space Heater - Electric Operation Fire - Space Heater - Fan Operation Fire - Space Heater - Gas Operation Fire Extinguishers Fire Retardant Foams Fire Safety Flyscreens FM Radio Connection For both types of aerial Front & Back Levelling Front Panel and Gas Bottle Locker Lid Fumes - Petrol/Diesel Fumes Furniture - Cleaning Gas Barbecue Point Gas Connection Gas Dispersal Holes Gas Grill Gas Hob Gas Hoses - High Pressure Gas Locker Door Gas Locker Door - Avanté and Corona Models Gas Locker Door - Odyssey / Omega / Crusader / Rallye and Buccaneer models Gas Oven Gas Regulator Gas Safety Advice Gas Supply General Questions 124 54 45 10 39 39 39 10 10 10 44 50 20 72 9 57 28 24 9 36 35 25 46 46 46 36 24 28 24 104 General Safety Generator/Charger: Getting Started Glossary of terms Grill - Gas Handbrake Heki 2 & Heki Duette Luxus Rooflight Heki 2 & Heki Duette Luxus Rooflight - Closing the blinds: Heki 2 & Heki Duette Luxus Rooflight - intermediate position: Heki 2 & Heki Duette Luxus Rooflight - Opening the Blinds: Heki 2 & Heki Duette Luxus Rooflight - tilted position: Heki 2 & Heki Duette Luxus Rooflight - ventilation position: High Pressure Gas Hoses Hitch Head Operation - Winterhoff Stabiliser Hob-Gas How to Use Your Caravan’s Equipment Index Interior Walls - Cleaning Internal Doors Internal Lights - Maximum Bulb Ratings Internal Loading & Checks Internal Wiring Jacking Jockey Wheel - Nose Weight Indicator Jockey Wheel - Nose Weight Indicator Kitchen Taps Leveller Jack Levelling - Front & Back Levelling - Leveller Jack Levelling - Ramp 8 22 22 108 36 17 42 43 42 43 42 42 25 13 35 34 121 57 46 31 12 79 63 12 51 45 20 20 20 20 Levelling - Side-To-Side Loading Long Term & Winter Storage LPG - Facts about LPG LPG Gas System L-Shape Lounge Double Bed - Bed Make Up Lubrication Magnetic Catches Mains Electrics Mains Supply - Connecting To On Arrival at Site Mains Supply - Disconnecting When Leaving Site Mains Supply - Electricity Maintenance of your BPW Chassis Microtag© Microwave (where fitted) Midi Heki Rooflight Mini Heki Nose Weight Indicator Jockey Wheel Nose Weight Indicator Jockey Wheel Odyssey - Technical Specification Odyssey & Omega - Equipment List Odyssey / Omega Air Con Specials - Technical Specification Odyssey / Omega Specials - Technical Specification Odyssey Internal Wiring Odyssey Road Lights Odyssey, Omega, Rallye, Crusader and Buccaneer - Electrical Control Panels Omega - Technical Specification Omega Internal Wiring Omega Road Lights 20 12 66 28 28 48 64 47 71 22 23 22 64 52 40 43 43 12 51 95 75 103 102 80 87 34 98 83 90 Omivent (12v) Rooflight Omni directional Aerial - Status 315 Other Means of Attachment Oven - Gas Overseas Electrical Connection Panic Alarm Parallel Lounge - Bed Make Up Parking on a Reverse-Sloping Site or Steep Hill Petrol/Diesel Fumes Polyplastic Window Opening Power Drain -Storage Power Supply Charger Preparing for the Road Pressures - Tyres Pre-Tow Checklist & Hitch-Up Rallye - Technical Specification Rallye Internal Wiring Rallye Road Lights Ramp Refrigerator - 12V Operation (Avanté & Corona) Refrigerator - 12V Operation (Crusader, Rallye and Buccaneer) Refrigerator - 12V Operation (Odyssey and Omega) Refrigerator - 230V Operation (Avanté and Corona) Refrigerator - 230V Operation (Crusader, Rallye and Buccaneer) Refrigerator - 230V Operation (Odyssey and Omega) Refrigerator - Gas operation with electronic ignition (Avanté and Corona) Refrigerator - Gas operation with electronic ignition (Crusader, Rallye and Buccaneer) Refrigerator - Gas operation with electronic ignition (Odyssey and 42 49 16 36 23 55 47 21 9 43 66 22 12 61 13 99 84 91 20 37 38 38 37 38 38 37 Index Explorer Group 2007 Touring Caravan Handbook 38 38 125 Index Omega) Refrigerator Operation Remedial Work Removable Drawer Locker Reversing Road Lights Robstop WS3000 Rooflight - Standard MPK Rooflights Security Seitz Window Opening Selecting a Pitch Setting Off Setting Off - Before Shower and Bathroom Taps Shower and Bathroom Taps (Avanté and Corona) Shower and Bathroom Taps (Crusader, Rallye, Omega & Odyssey) Shower Trays, Shower Room and Wash Basin Fittings - Cleaning Side-To-Side Levelling Site Regulations - Check Sliding Doors Smoke Detector Space Heater - Electric Operation Space Heater - Fan Operation Space Heater - Gas Operation Space Heater Operation Spare Parts Spare Parts -Procurement Speed Limits Sprung Hinges 126 37 71 49 18 86 53 43 42 52 44 20 18 16 45 45 45 58 20 20 47 40 39 39 39 39 71 64 18 47 Stabiliser - Activating Stabiliser - Checking Stabiliser - Disengaging Stabiliser - Uncoupling Status 315 Omni directional Aerial Status 530 Directional Aerial Storage Taps Technical Specifications Thetford cassette toilet Thetford Refrigerator (Avanté and Corona models) Thetford Toilet - Cleaning Toilet - See Cassette Toilet Toilet/Shower Room Doors Towing and Driving Truma Space Heater - Cleaning Truma Ultraflow and Ultraflow Compact Housing - Routine Maintenance TV Aerial Tyre Wear and Damage Tyres Ultraflow Compact Housing - Operating instructions Ultraflow Filter Housing - Operating instructions Ultraflow Filter Housing or Compact Housing - Connection to Ultraflow Water Pump Assembly - Compact or Filter system Accessories - Cleaning Uncoupling Ventilation Ventilation - Awning Spaces, LPG and Appliance Exhaust Ventilation - High-Level 14 14 14 14 49 50 66 45 93 41 37 60 41 46 18 60 58 49 62 61 26 25 26 59 14 9 28 9 Ventilation - Low-Level Ventilation in Separate Bedrooms VHF Television Reception (Overseas only) Warranty Warranty - Conditions Attached to the Warranty Warranty - Parts Covered By This Warranty for Years 1 - 3 Warranty - Specific Exclusions for Years 2 & 3 Water Water Containers - Cleaning Water Heater - 230V Operation Water Heater - Gas operation Water heater operation Water Ingress - Code of Practice Water System - Cleaning Water System - Draining Down Water System Preparation for Winter Use Water Systems – Sterilization Waterline - How to Use Weights - Caravan Towing Vehicle Weight Ratio Welcome & Introduction When The Breakaway Cable Is Attached Check To Ensure Where a Designated Attachment Point Is Provided On The Tow Bar Where No Designated Attachment Point Is Provided On The Tow Bar Window Blinds & Flyscreens - Cleaning Window Etching & Chassis Marking Windows - Components Windows - Opening Winter Storage 9 9 50 68 68 68 68 25 59 39 38 38 70 58 27 59 60 26 12 6 16 15 Winter Storage Winterhoff Stabiliser – Hitch Head Operation 66 13 Index 20 Explorer Group 2007 Touring Caravan Handbook 16 57 53 72 43 58 127 All the illustrations and descriptive matter in this guide are intended to give a general idea of the caravan. Changing market and supply situations may prevent the manufacturer from maintaining the exact specifications and details in this handbook and we therefore reserve the right to alter specifications and materials as conditions demand. Retailers are independant of the manufacturer and have absolutely no authority to bind the manufacturer by any express or implied undertaking or representation. Explorer House, Delves Lane, Consett, Co Durham. DH8 7PE Tel : 01207 699000 Fax : 01207 699001 Web : www.explorer-group.co.uk