Transcript
OWNER’S MANUAL
MODEL: M-FUSION DESCRIPTION: Motus® Fusion Group Indoor Racing Bike INCLUDES: Motus® M-Racing PC; Dual SPD & Cage Pedals & CHR ALL RIGHTS RESERVED; COPYRIGHT® MOTUS USA 2008
1
Dear Motus USA Customer, We would like to thank you for buying our studio sports training equipment ,hope that it affords you the desired satisfaction. Please note and follow the information and instructions for assembly and use. If you have any questions, please contact at any time.
SAFETY INSTRUCTIONS Before you start training on your sports training equipment, please read the instructions carefully. Be sure to keep the instructions and any other accompanying in case of repair and for spare parts delivery. z Use only original parts as delivered. z Check before the equipment is first used, and again at regular intervals, that all screws, bolts, nuts and other connections have been done up tightly, to ensure that your training equipment is in a safe operating condition at all items. z Place the bike on an even, non-slippery surface. Because of possible corrosion, the usage of the bike in moist areas is not recommended. z Check every 1-2 month that all connecting elements are tight fitting and are in the correct condition. z Only carry out training work on the equipment when it is in perfect working order. z One person for training may only use the equipment. z The bike is designed for adult. Children are not allowed to use this bike. z Always pay attention that you or any other persons never bring parts of the body in close proximity to any parts of the equipment that are still moving. z Consult your physician before starting with any exercise program. He can advise which kind of training and impact is suitable. z When making settings for any adjustable parts, check that they are in the right position and also check the marked maximum setting. z Please follow the advice for correct training as detail in training instructions. z This bike not suits for therapeutic use. z The user’s max. Weight in 120 KGS.
2
Basic Maintenance and Pre-us Suggestions and Requirements: - Lubricant is recommended as a Silicone Spray (Do Not Use WD-40). Lubricate seat neck and display neck if adjustment becomes difficult. - Flywheel should be thoroughly cleaned prior to; and port workout. This will prevent build up on flywheel as-well as limit rough operation of the unit. - Check foot mounts to ensure they are adjusted accordingly. - Check Resistance to ensure that all bikes have matching tension. - Adjust Resistance to desired preference. - Always keep bikes clean and wipe down after use, for improved product longevity.
PARTS LIST: Item Description 1 Main Frame 2 Rear Foot Bar
Quantity 1 1
3
Front Foot Bar
1
4
U-Zone Bar
1
5
Seat Post
1
6
Handle Post
1
7
Seat Slider
1
8
Handle Bar
1
9
End Cap
2
Item Description 39 Nut 40 Adjustable Bolt
Quantity 2 2
41 Lock Nut 42 Function Set
2
43 Stopper Set 44 Function Controller
1
45 Screw 46 Inner Chain Cover
2 2
2 1 1
10 Adjustable Pad 11 Move Wheel
2
47 Screw 48 Belt
2
49 Belt Deck
1
12 Hex Head Bolt
2
50 Screw
4
3
1
13 Nylon Nut 14 Washer
2
51 Outer Chain Cover 52 Round Head Screw
1
15 Hex Head Bolt 16 Cap Nut
4
53 Left Crank 54 Right Crank
1
17 End Cap 18 Bearing
2
1
2
55 Left Pedal 56 Right Pedal
19 Bearing
2
57 Bolt
2
20 S Nut 21 Belt Wheel Rod
1
58 Cap 59 Plug
2
22 Left Cover 23 Right Cover
1
4
1
60 Knob 61 Flat Washer
24 Top Left Cover
1
62 Seat
1
25 Top Right Cover 26 Rear Cover
1
63 Round Head Bolt 64 End Cap
2
27 Front Left Cover 28 Front Right Cover
1
65 Washer 66 Spanner
2
29 Screw 30 Screw
1
67 Spanner 68 Washer
1
31 Screw 32 Screw
2
69 Nut 70 Foam Pad
2
33 Tapping Screw 34 Tapping Screw
2
71 Bracket 72 Bolt
1
35 Flywheel 36 Belt Wheel
1
1
1
73 Nut 74 Washer
37 Fly Wheel Rod 38 Spring Washer
1
75 Spring
1
4 2
1
1 1 1 2 2
2
4
6 1 1
2 2
1 1 2 2 1 1
OVERVIEW CHART:
5
PACKING PARTS LIST:
6
z z z z
Remove all parts and bags from box. Read the owner’s entire manual before assembly. Let out all parts and hardware pack as shown in pre-assembly checklist drawing. Some parts may be pre-assembled.
Step 1. Slide the Rear Foot Bar (2) to the rear of the Main Frame (1) with two Washers (14) and two Hex Head Bolts (15) as shown in Figure 1. Tighten all bolts used in Step #1 with one Spanner (66) at this time.
Step 2. Slide the Front Foot Bar (4) to the front of the Main Frame (1) with two Washers (14), two Spring Washers (68) and Hex Head Bolts (15) and Cap Nuts (16) as shown in Figure 1. Tighten all bolts used in Step #2 with two Spanners (66) & (67) at this time.
Step 3. Insert the U-Move Bar (4) into the holes of the Front Foot Bar (3) with two Washers (65) and Round Head Bolts (63) as shown in Figure 1. Tighten all bolts used in Step #3 with one Spanner (66) at this time.
Step 4. Fix the Left Pedal (55) and Right Pedal (56) to the L&R Crank (53 & 54) as shown in Figure 2. Tighten the Pedals used in Step #4 with one Spanner at this time. 7
Step 5. Insert the Seat Post (5) into the tube of the Main Frame (1) with Knob (60). Hands Tighten only at this time.
Step 6. Attach the Seat (62) on the bar of the Seat Slider (7) first. Then slide this set onto the Seat Post (5) with Flat Washer (61) and Knob (60) to tighten as shown in Figure 3. Hands Tighten only at this time.
Step 7. Insert the Hand Post (6) into the tube of the Main Frame (1) with Knob (60). Hands Tighten only at this time.
Step 8. Insert the bolt of the Pads(70) into the holes of the Hand Bar(8) With two Nuts(69) as shown in Figure 4. Tighten all bolts used in Step #8 with one Spanner (67) at this time.
Step 9. Attach the Handle Bar (8) on the Hand Post (6) with one Flat Washer (61) and Knob (60) to assemble as shown in Figure 3. Hands Tighten only at this time. MAKE SURE ALL NUTS AND BOLTS ARE TIGHTENED. FUNCTIONS ADJUSTMENT Adjustment the Tension at the Adjust Screw as Detail A. Adjustment Function at the Lock Nut and Adjust Wire see Detail B. Adjust must tighten the Lock Nut. 8
