Transcript
DS-2 RF
Owner‘s Manual
1 CHANNEL DIMMER
Notes on safety For your own safety you must read through this chapter at first completely! • • • • • • • •
•
• •
• • • • •
Risk of electrical shocks! Only connect the device to a properly wired and earthed mains power socket with mains voltage of 230 V ~ /50 Hz. Do not operate the device if the power cord or the mains plug are damaged. Never submerse the device in water. Wipe it with a slightly moistened cloth only. Do not expose the device to rain and never use it in a damp or wet environment. Make sure that the power cord never becomes wet or moist during use. Under no circumstances may you open the device housing. Should you do so your safety would not be assured and the warranty will become void. There are no operational components whatsoever inside, only really high voltage that can give you a deadly shock! Do not place objects containing fluids, e.g. flower vases or beer bottles, on or near the device. Notice regarding disconnection from mains-power: To completely disconnect the device from mains power, you must pull the plug from the power socket. For this reason the device should be placed in a position where unobstructed access to the power socket is assured at all times, so that in an emergency you will be able to immediately pull out the plug. To eliminate the risk of fire you should completely disconnect the power plug from the power socket when the device is not going to be used for a long time, for example, during holidays. Always grasp the power cord by the plug. Do not pull on the cord itself and never touch the power cord with wet hands as this could result in a short circuit or an electrical shock. Do not place the device, speakers or anything else on the power cord and make sure that it does not become clamped. Never tie knots in the power cord and do not bind it together with other cables. Lay the power cord so that no one can step on or stumble over it. A damaged power cord can cause a fire or an electrical shock. Check the power cord from time to time. Should it become damaged contact our customer service department to have it replaced. Always operate the device only on a correctly earthed socket, never sever the power cord’s earth wire. Otherwise a LIFE THREATENING situation exists! Never use this device in places, where it is subject to > excessive vibrations and/or impacts, > temperatures above 30°C / 100°F or below 5°C / 40°F, > extreme low or high humidity (ideal humidity is between 35% and 80%). Risk of fire! Never leave the device unattended during operation. Never cover the ventilation slots of the device while it is on. Do not place the device in locations that are subject to direct sunlight. If you do, it may overheat and become irreparably damaged. Never operate the amplifier in the vicinity of heat sources such as cookers, heating elements or other heat producing installations. Do not place open fire sources, such as candles, on the device. Before a storm and/or a thunderstorm with a risk of lightning, please disconnect the device from the electrical power source.
Risk of personal injury! • Keep children away from the power cord and the device. Children frequently underestimate the dangers of electrical devices. • Provide a stable location for the device. • Do not operate the device if it has sustained a fall or is damaged. Have the device checked or, if necessary, repaired by qualified technicians.
2
ATTENTION! • Damages caused by the disregard of this user manual are not subject to warranty. Neither the manufacturer nor the importer will accept liability for these kind of damages or any resulting damages, defects, or problems. The electric connection must only be carried out by a qualified electrician! All electric and mechanical connections must comply with European safety norms.
Specifications Voltage supply.................. AC230V~50Hz, 6A max. Number of channels......... 1 channel, 10A max. DMX output...................... 3-pin XLR panel jack DMX input......................... 3-pin XLR panel plug Fuse................................. F10A, 250V, 5x20mm Dimensions....................... 182 x 92 x 65mm Weight.............................. 1.1kg Our products are subject to a process of continual further development. Therefore modifications to the technical features remain subject to change without further notice.
Disposal Never throw the device into the regular household waste at the end of its useful life. This product is subject to the European Directive 2002/96/EC. • Dispose of the device through an approved disposal centre or at your community waste facility. • Observe the current existing regulations. In case of doubt contact your disposal facility. • The packaging is certified via a dual system. Take all packaging materials to an environmentally friendly disposal facility in compliance with the local regulations.
Maintenance and care • Never submerse the device in water or any other liquid. Don‘t let any liquid get into the housing. This would damage the unit and cause a short circuit. • Before cleaning the device you must disconnect it from the mains. Clean the surface of the device only with a slightly damp cloth. Never use petrol, solvents or any aggressive cleaners! These could damage the surface of the unit‘s housing!
Features XX 1 controllable channel XX Manual dimming function available XX Dimmer pack or switch pack selectable XX Also suited for inductive loads XX Display for DMX address and menu guiding XX DMX – 512 in/output XX Fault current memory XX Allows DMX addressing, dimmer preset and dimmer limit
3
Front panel
1. Output socket 2. Display 3. p-button 4. -button 5. MENU button 6. Mini phone jack 7. External fader 8. DMX output socket 9. DMX input socket 10. Fuse 11. Mains cable 12. HTP fader
4
to connect the device to be controlled, 10A max. shows current operations and functional status. press this button to increase the value by „1“. Keep it pressed for quick increasing. press this button to decrease the value by „1“. Keep it pressed for quick decreasing. press this button to enter the sub menu. to connect the external fader. this fader has the same function as the one on the units control panel. 3-pin XLR female socket, to send out the DMX signal. 3-pin XLR male socket, to receive the DMX signal. F10A 250V, 5x20mm. for connection to the mains voltage supply. use this fader to control the brightness. Its operation principle is HTP, so the highest output value has priority.
Operating Connect the unit to the mains power supply. The device will automatically load the settings used last time the unit was used. The display shows the last used DMX address, as all information is stored in the power failure memory. If the power supply is unstable, the display shows „AC-0“. Wait then, until this indication goes out. DS-2 RF can be used as a dimmer or switch pack depending on the operating mode you choose.
DMX addressing 1. The display shows the DMX address, that was set as the unit was disconnected from the mains last time. If the last DMX address was 123, then the display will show 123.
2. Set the DMX address using the UP and DOWN buttons. If you keep the buttons pressed, you can move ahead or back faster. If you have selected a DMX address it will automatically be stored. Attention! During addressing the output will be disabled.
Switch Pack mode 1. Input the complete DMX address and press the MENU button, to proceed to the next menu.
2. Press the UP and DOWN buttons, until the display shows „S---“.
5
3. Press the MENU button, to switch to the Switch Pack modem which consists of “Switch On” (S-on) and “Switch Off” (S-off). In “Switch On” mode the output is set to “ON” and the connected lamp will light up independently from the DMX signal. In “Switch OFF” mode the lamp will be switched off. When the DMX signal rises above 40%, the lamp will be switched on.
4. Press the UP and DOWN buttons, to toggle between “Switch ON” and “Switch OFF”.
5. When the desired mode is set, press the MENU button to return to the addressing menu.
Dimmer Pack Mode 1. Press the MENU button, to proceed to the next menu.
2. Press the UP and DOWN buttons, until the Display shows “d…”.
3. Press the MENU button, to change to the Dimmer Limit mode.
6
4. Press the UP and DOWN buttons, to enter a value between 10 and 100. Pressing the button changes the value by 1. Keep the button pressed, to change the value quickly. When the Dimmer Limit is set, it will automatically be stored.
5. Press the MENU button, to change to the Dimmer Preset mode.
6. Press the UP and DOWN buttons, to enter a value between 0 and 100. Pressing the button changes the value quickly. When the Dimmer Preset is set, it will automatically be stored.
7. Press the MENU button, to return to the DMX addressing.
7
© 2010 Musikhaus Thomann e.K. Treppendorf 30 • 96138 Burgebrach • Germany www.thomann.de
