Transcript
Floor Machine/Dual Speeds
OWNER’S MANUAL IMPORTANT: READ OWNER’S MANUAL CAREFULLY Please fill out and return your warranty card
MODEL 261119
031811
TABLE OF CONTENTS
CONGRATULATIONS on your purchase of a Global product. We appreciate your business and will do everything in our power to keep you happy with your purchase for many years to come. Your purchase entitles you to the best protection by one of the most comprehensive warranties in the industry. Thank you for purchasing a GLOBAL product.
TABLE OF CONTENTS Safety Precautions
3
Machine Operation
4
Machine Maintenance & Storage
4
Handle Release Assembly Instructions
5
Parts Lists
6-9
Wiring Diagram
10
ORDER YOUR CLEANING CHEMICALS & PADS Visit www.globalindustrial.com Or Call 1-800-645-1232 CLEANING CHEMICALS
PADS (Case of 5) 20” Floor Pad Model 261165 Specify suffix: Scrubbing (GN), Buffing (RD), Stripping (BK) or Polishing (WH).
Floor Finish Model 640403 (Case of 4)
Floor Cleaner Model 640404 (Case of 4)
Floor Stripper Model 640405 (Case of 6)
2
SAFETY PRECAUTIONS All operators shall read, understand and exercise the following safety precautions:
GROUNDING INSTRUCTIONS
! WARNING
1) Do not operate machine: • Unless trained and authorized • Unless you have read and understood operator’s manual • In flammable or explosive areas. • With damaged cord or plug. • If not in proper operating condition. • In outdoor areas. • In standing water. • With the use of extension cords.
Do not remove the ground pin under any circumstances! This floor/finishing machine shall be grounded while in use to protect the operator from electric shock. The machine is provided with a three - conductor cord and a three-contact grounding type attachment plug to fit the proper grounding type outlet. The green (or green and yellow) conductor in the cord is the grounding wire. Never connect this wire to other than the grounding pin of the attachment plug.
2) Before operating machine: • Make sure all safety devices are in place and operating properly.
This machine is for use on a nominal 120-volt circuit and has a grounding plug that resembles the plug illustrated in figure below. Make sure that the machine is connected to an outlet having the same configuration as the plug. No adapter should be used with this machine.
3) When using machine: • Do not run machine over cord. • Do not pull machine by cord or plug. • Do not pull cord around sharp edges or corners. • Turn power switch to “off” prior to unplugging machine. • Do not unplug by pulling on the cord. • Do not stretch cord. • Do not handle plug with wet hands. • Keep cord away from heated surfaces. • Do not pick up burning or smoking debris such as cigarettes, matches or hot ashes. • Report any damages to your supervisor. • DO NOT attempt to fix machine by yourself. All repairs must be made by authorized technicians. 4) Before leaving or servicing machine: • Turn off machine. • Unplug cord from outlet.
This machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. • Use with approved accessories only • Use with non-approved accessories voids warranty • DO NOT modify machine • Modification to machine voids warranty
5) When servicing machine: • Unplug cord from outlet. • Use manufacturer supplied or approved replacement parts. • Any lifting or hoisting of machine should be done with OSHA approved equipment and safety precautions.
3
OPERATION OF FLOOR MACHINE MAINTENANCE To keep the machine performing well for many years, please follow the following maintenance procedures.
READ OPERATOR’S MANUAL THOROUGHLY PRIOR TO OPERATING OR SERVICING THIS MACHINE
! WARNING Always confirm that the machine is unplugged prior to performing any maintenance or repairs.
GENERAL USE 1. Remove any obstructions or other obstacles in the area which is to be cleaned. 2. Place the handle in the upright position and tilt machine back until handle rests on the floor.
1. Unplug machine as soon as you are done using it. 2. Tilt machine back and remove pad driver or brush.
!
CAUTION
Never store a low speed machine with the pad driver or brush mounted to the machine.
! WARNING Be sure the machine is not plugged into an outlet.
3. Clean the outside of the machine with a mild cleaner. 4. Check power cord for any damage. If damage is detected, replace power cord immediately. 5. Lubricate wheels with a water resistant lubricant once a month. 6. Check machine for loose or missing nuts and bolts, and replace as necessary. 7. If the machine is used in a dusty environment, you may remove the motor cover and blow the motor clean with compressed air. This will ensure proper ventilation, and allow the motor to run cooler.
3. Attach the pad driver or brush to the machine by placing the clutch plate over the gearbox hub and turning the driver/brush 1/4 turn. 4. Place machine back into its upright position. 5. Plug power cord into a grounded outlet.
! WARNING Never use an extension cord in conjunction with the standard power cord. 6. The handle height may be adjusted by lifting up the compression handle (located on the right side of the handle tube) about 1 foot above floor level. Release the compression handle and adjust handle to safe operating height, then push back down on the compression handle to lock the handle in operating position. 7. Select either low speed (185 rpm) or high speed (330 rpm) by pushing the motor mounted switch into the low or high position.
STORAGE 1. Unplug machine from power source and wrap cord on handle. 2. Tilt machine back and remove pad driver or brush. 3. Store machine in upright position and in a dry area.
! WARNING Never change the speed while operating the machine. Turn power off prior to changing the speed. 8. To start the machine, press the red safety button on the top of the upper switch housing, and then squeeze either of the operating triggers. (the safety button must be depressed prior to squeezing the operating triggers). 9. When the machine is in operation, both hands should be placed on the switch housing (upper handle). 10. During operation, to make the machine go right, gently raise the handle. To make the machine go left, gently lower the handle. 11. To stop the machine at any time, simply release the operating trigger(s) and the machine will stop automatically.
4
MODEL 261119 - HANDLE RELEASE ASSEMBLY
STEP 3 1. Place cord wrap assembly (2 pieces) in place, and snug them together with 6mm hex bolt. (Actual cord wrap faces to the left of the machine when you are standing behind it.) 2. Assemble hardware in the following order: Spacer; left handle bracket; nylock nut. (DO NOT overtighten nylock nut. Only tighten it enough to hold handle in place when compression lever is in down position.)
STEP 4 1. Connect power cords together. 2. Connect power cord covers together.
STEP 2 1. Remove handle clamp blocks with 5mm hex head 2. Place handle assembly into handle clamp blocks. 3. Re-attach the blocks to the base with 5mm hex head
STEP 1 1. Remove nut and spacer from handle bracket assembly. 2. Push the two handle brackets forward so they lean against the motor.
5
MODEL 261119 - HANDLE ASSEMBLY PARTS LIST
6
MODEL 261119 - HANDLE ASSEMBLY DIA No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
Part Number VF30016 VF30015 VF30018 VF13503 VF30017 VF30014 VF45120 VF50120 VF13504 VF13517 VF14114 VF30013 VF13493 AS112205 VF44018 W13661 VF48306 VF44016 VF45119 AS22009 VF30108 VF14223 VF14218 VF13528 VF30102 VF99012 VF30109 GT13013 VF48309 VF44017 VF99023
Description HANDLE RELEASE BOLT HANDLE RELEASE WASHER, PLAIN NUT, MB X 5.7 SCREW COVER, HOOK, CORD CORD, HANDLE GROMMET NUT, M10 WASHER, PLAIN SCREW MBX55 HOOK, CORD SCREW, M8 X 10 TUBE LEVEL, SOLUTION SCREW, M4 X 12 PIN LEVEL, LEFT, SWITCH CORD, POWER SUPPLY STRAIN RELIEF, CORD GASKET, HANDLE, SOLUTION SCREW M8 X 25 SCREW M8 X 45 TEETH WASHER 06 REAR COVER BREAKER 12A/1.5HP COVER NUT, M4 CLAMP BLOCK LEVEL, RIGHT, SWITCH SWITCH ASSY
VF14212 VF13527 VF13526 VF46705 GV40218 VF48310 VF30101 VF47035A VF13604 VF14222
SCREW, M3 X 25 TEETH WASHER 04 SCREW M4 X 30 SAFETY BOTTOM SPRING, SAFETY BLOCK HAND GRIP FRONT COVER LOGO TEETH WASHER 05 SCREW M5 X 12
7
NO Req'd 1 1 2 1 1 1 1 1 1 1 1 1 1 2 1 2 3 1 1 1 1 2 2 2 1 1 1 3 1 1 1 2 1 1 1 1 2 1 1 4 4
MODEL 261119 - BASE ASSEMBLY PARTS LIST
8
MODEL 261119 - BASE ASSEMBLY DIA No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
Part Number GT13080 VF30011 AS112210 VF30020 W20274 GV40235 W13621 VF13474A VF13613 VA13474 VF13524 VF13519 VF13618 MF-VF022 VF30004 VF30006 VF30008 VF40152 VF30019 VF13520 VF50119 VF48202 VF13666 VF44012 VF13612 VF999802A VF99021 VF40990 VF41079 VF30025 VF99006 VF99022 VF40994 VF40997
Description SCREW M6 X 30 CLAMP BLOCK, HANDLE AXLE BRACKET, LEFT HANDLE WASHER, PLAIN 013 CLAMP BLOCK, AXLE SELF-TAPPING SCREW ST5 X 20 WASHER, PLAIN 05 SCREW M5 X 20 SCREW M5 X 16 WASHER, PLAIN 08 WASHER, LOCK 08 SCREW 5/16" X 2-1/4" 19" PAD HOLDER BUMPER 20" FRAME 20" ALUMINUM BASE, MOTOR BARB HOSE BRACKET, HANDLE, RIGHT WASHER, LOCK WASHER, LOCK WHEEL 5" WASHER, 06 SCREW, M6 X 12.7 M5 X 12 GEAR BOX COUPLING LABEL, DUAL SPEED LABEL LABEL, MOTOR DUAL SPEED MOTOR MOTOR W/GEAR BOX READ MANUAL LABEL SERIAL TAG
9
NO Req'd 4 1 1 1 4 2 4 4 2 2 4 4 4 1 1 1 1 1 1 2 2 2 2 2 6 1 1 1 1 1 1 1 1 1
MODEL 261119 - WIRING DIAGRAM
10
