Transcript
O Z V E C T O R 3 ®
S U B W O O F E
1181 South Rogers Circle, Suite 18 Boca Raton, Florida 33487 www.jti-innovation.com
01/05
R
e-mail
[email protected]
Congratulations on your purchase of an Oz Audio Vector 3 Series subwoofer. The Vector 3 subwoofers represent Oz Audio’s design approach to producing a bass pounding and cost effective low frequency driver. Only the best materials and production techniques were used to create an exceptional line of subwoofers. We hope you will enjoy your Vector 3 subwoofer for many years to come.
Features: • Custom designed, illuminated Oz dustcap • Industrial finish, Oz powder coated basket • 2-inch, dual 2 or 4-ohm coils on an aluminum former w/ reinforced neck joint • Custom low distortion linear flux design with back plate ventilation • Underlap™ cone attachment • Custom injected-molded, brushed aluminum poly-mica cone • Vapor deposition technology • U-Turn Hyper-Surround™ for maximum linear excursion • Poly-cotton blended flat progressive-roll spider with woven flat tinsel leads • Precision machined and matched motor assembly • Black e-coated magnetic plates provide superior voice coil cooling • Nickel plated terminals • 50 oz. high intensity grade ferrite magnet • Custom embossed, protective magnet boot
The Vector 3 subwoofers offer the most value for the most discriminating listener. They are designed to perform well in sealed, vented, or bandpass enclosures. For optimum performance, make sure to have your authorized Oz Audio dealer design and build your subwoofer system. They are equipped and trained to deliver the best system design and installation.
1.
Calculating Enclosure Volume
Specifications Model
V10.3-2
V10.3-4
V12.3-2
V12.3-4
Fs (Hz)
38.81
39.73
36.71
37.48
Qts
.65
.76
.68
.8
Vas (Liters)
17.25
17.25
40.99
40.99
Re (Ω) (parallel)
1
1.85
1
1.85
Xmax (mm)
10
10
10
10
Sens (dB 1W/1M) Rms/Peak (Watts) Mounting Depth Mounting Diameter
85
84
87
87
350/700
350/700
350/700
350/700
4 7/8”
4 7/8”
5 1/2”
5 1/2”
Multiplying all three internal dimensions in inches and then dividing the product by 1728 will produce the enclosure volume in cubic feet.
9 1/8 ”
9 1/8 ”
11 1/8”
11 1/8”
(H x W x D) / 1728 = Enclosure Volume ft.³.
D H
W
Enclosures should be constructed with 3⁄4 inch MDF to prevent flexing of the enclosure walls. When assembling the enclosure all panels should be first glued, and then fastened together with either a brad nailer or screws in pre-drilled holes. After the enclosure has been assembled all seams should be sealed with silicone.
Enclosure Recommendations
2
Sealed
V10.3-2
V10.3-4
V12.3-2
V12.3-4
Box Volume
.8 ft.³
.8 ft.³
1.25 ft.³
1.25 ft.³
F3
48 Hz
45 Hz
46 Hz
44 Hz
Vented
V10.3-2
V10.3-4
V12.3-2
V12.3-4
Box Volume
1.25 ft.³
1.25 ft.³
1.5 ft.³
1.5 ft.³
F3
29 Hz
30 Hz
33 Hz
33 Hz
Fb
38 Hz
38 Hz
38Hz
38 Hz
Port Dia.
3”
3”
4”
4”
Port Length
8.5”
8.5”
12.75”
12.75”
Enclosure recommendations are internal volumes. Brace displacement, and port displacement must be added to the volumes listed above. NOTE: When constructing a vented enclosure, equalization is not recommended below the enclosure tuning frequency (Fb). Also, the end of port should be no closer than it’s own diameter to the wall opposite the opening.
Oz Dustcap LED Lighting The Vector 3 subwoofers’ dustcap can be illuminated with a blue Oz logo. To activate the LED lighting, connect the terminals that are above the LED designation on the magnet boot. The terminals are marked as + and –. Connect the – terminal to ground and connect the + terminal to a positive 12-volt source that deactivates when the ignition is turned off. Possible sources for a12-volt signal would be an ignition wire at the ignition switch, the amplifier activation output from the radio, or a switch installed to activate the lighting.
3
CAUTION This high-performance subwoofer is capable of producing sound pressure levels that can cause hearing impairment or permanent loss. Please avoid prolonged exposure to sound pressure levels in excess of 100dB to prevent such damage. Oz Audio assumes no liability for bodily injury or property damage caused by the misuse of this product.
To locate the nearest Oz Audio® dealer, please call (561) 998-0211 between 9:00am and 6:00pm EST. Monday thru Friday, or email us at
[email protected], or write to JTI, 1181 South Rogers Circle, Suite 18, Boca Raton, FL 33487. Due to ongoing product development, all specifications are subject to change without notice. For detailed specifications on all Oz Audio speakers, please visit our website (www.ozaudio.com) or consult with your authorized Oz Audio retailer.
4
5
