__p X27 Quick Guide【 English 】

Transcript

X27 Quick Guide【 English 】 __p B. DDR2 Installation 1. Unlock the DIMM latch. C4 Front Panel F1. USB2.0 Port F2. Mic-In F3. Line-Out F4. Power Switch F5. Click to open C5 F1 F2 F3 F1 Back Panel B2. PS/2 Keyboard Port B3. COM Port B4. VGA Port B7. LAN Port B5 B6 B7 B8 B9 B11 USB2 Notch Latch 7. Connect the ODD cable and power cable to optical drive For PATA(IDE) slim optical drive(Optional) USB3 Power Button Header 3. Check that the latches are closed, and the DDR2 modules are firmly installed. 2 1 B10. Line-In Port B11. DC Power Port CLASS 1 LASER PRODUCT 3 6 8 10 5 7 9 C. Component Installation 1. ������������������������������������������������������������� Place HDD on top of bracket and align the HDD connector with point B IDE Cable Slimline SATA Cable 2. Secure with screws from the side. Note: For safety reasons, please ensure that the power cord is disconnected before opening the case. 4 Connecting the Network (LAN Port) 5 Connecting Speaker (Line-Out Port) Power Cable 8. Secure the Slim DVD with screws from the side. 3. �������������������������������������� Take out converter from accessory box and ����������������������������� connect to the optical drive (Optional) 9. Slide the rack downward and onward in replace the chassis. Support 5.1 channels 1. Unscrew 2 thumbscrews of the chassis cover. 2. Slide the cover backwards and upwards.(1.Pic) 1 2 Fan Connector- FAN1 6 Connecting Headphone & Microphone (Line-Out & MIC-In Port) 7 Connecting Power (DC Power Port) 8 Powering on the System (Power Switch) Front Panel Header- JP2 ITE 8718F Chipset C4 Connecting USB Device (USB Ports) For SATA slim optical drive 3. Slide the rack backwards and upwards.(2.Pic) C2 3 DVI Port A. Begin Installation PS/2 K/B & M/S Ports CD-In Header- JP4 Power Cable or CAUTION： INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. USB2.0 (x2) Ports VGA Port & DVI Port COM Port Line-In/ Line-Out / MIC-In Ports 4 VGA Port Read the following precautions before setting up a Shuttle XPC. The optical disc drive in this PC is a laser product. The drive's classification label is located on the drive. LAN & USB2.0 (x2) Ports C1 Connecting Monitor (VGA Port or DVI Port) Latch Laser compliance statement Motherboard Illustration C3 2 Cutout Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Dispose of used batteries according to the manufacturer's instructions. B9. Line-Out Port B4 1=USBPW4 2=USBPW4 3=USBP6N 4=USBP7N 5=USBP6P 6=USBP7P 7=GND 8=GND 9=KEY 10=GND CAUTION B8. Mic-In Port B3 Pin Assignments (USB3): 1=USBPW3 2=USBPW3 3=USBP2N 4=USBP3N 5=USBP2P 6=USBP3P 7=GND 8=GND 9=KEY 10=GND Connecting Keyboard and Mouse (PS/2 Mouse, PS/2 Keyboard Port) B6. USB2.0 Ports B2 Pin Assignments (USB2): 1  Safety Information B5. DVI Port B1 2. Align the DDR2 module’s cutout with the DIMM slot notch. Slide the DDR2 module into the DIMM slot. 1=HDLEDPWR 2=GRNLEDA 3=-HD_LED 4=GRNLEDB 5=BT_SEL 6=-PWRSW 7=GND 8=GND 9=NC 10=KEY B1. PS/2 Mouse Port B10 USB Headers Pin Assignments (JP3): F4 F5 X27 System Quick Guide【 English 】 6. Place the Slim DVD in the rack . 2 2 Fan Connector- FAN2 USB Headers- USB2 ,3 Clear CMOS Jumper- JP1 1 Intel 945GC Chipset (1) 1 (2) Intel Atom 230 4. Untie all cables for easier installation ICH7 Chipset For PATA(IDE) slim optical drive(Optional) BIOS Chip 240 pins DDR2 DIMM One IDE Slot- IDE1 C5 4. Secure converter with two screws (Optional) Serial ATA- SATA 1,2 Power Button Header- JP3 ATX Power Connector- ATX1 D. Complete 1. Replace the cover and refasten the thumbscrews. Jumper Settings C1 Front Panel Header C2 For SATA slim optical drive Clear CMOS Jumper Pin Assignments (JP2): Pin Assignments (JP1): 1=MIC2_L 2=AGND 3=MIC2_R 4=FRONT CTL 5=LINE2-R 6=SENSE1_RETURN 7=FRONT_SENSE 8=KEY 9=LINE2-L 10=SENSE2_RETURN 1=RTC_RST2=-RTCRST 3=-RTCBTN Pin1-2 Pin2-3 2 . Complete. (Default) (Clear CMOS) 2 4 6 8 10 C3 8 5. Connect the Serial ATA and power cables to the HDD. CD-In Header 4 3 Pin Assignments (JP4): 1 3 5 7 9 1=CD-In – Left 2=Ground 3=Ground 4=CD-In – Right 1 2 3 1 4 5 6 7 2 Serial ATA Power Cable Serial ATA Cable LThe product’s color will depend upon the actually shipping product. PAR-MA3159-H001