Transcript
VINE TRIMMERS
PARTS MANUAL FOR P2200T CODE #0113 3750 & P2200TS CODE #0113 3650 Marketed by: 13477 Benson Ave. Chino, CA Ph: 909/548-4848 Fax: 909/548-4747 FORM: CollardVineTrimmerPartsP2200T_TS
May 2014
TABLE OF CONTENTS SECTION
DESCRIPTION ................................................ PAGE
1
Introduction .................................................................................. 1 Operator's Responsibility ...................................................................... 1 Spare Parts - Frames ............................................................... 2 - 15 Reinforced Frame .........................................(PL 4049) ....................... 2 Complete Vertical Double Frame ..............(PL 4050) ....................... 3 Horizontal Large Frame RH .......................(PL 4051) ....................... 4 Horizontal Large Frame LH .......................(PL 4052) ....................... 5 Hydraulic Block w/Protection ...................(PL 4053) ....................... 6 Lower Fixing .................................................(PL 2262) ....................... 7 Top Fixing ......................................................(PL 3190) ....................... 8 Braces .............................................................(PL 2261) ....................... 9 Lateral Support .............................................(PL 3601) ..................... 10 Top Arms .......................................................(PL 2253) ..................... 11 Retractable Arm ............................................(PL 3179) ..................... 12 Complete Angle Brake Assy .......................(PL 0671) ..................... 13 Support For Cross Slope LH ......................(PL 3755) ..................... 14 Support For Cross Slope RH ......................(PL 3753) ..................... 15 Double Effect Cylinder ................................(PL 3754) ..................... 16 Spare Parts - Cutting Elements ............................................ 17 - 36 Double Frame Elements ............................(PL 4870a) ..................... 17 51" Cutting Element RH ..............................(PL 3686) ................18-19 51" Cutting Element LH ..............................(PL 3688) ................20-21 Hydraulic Motor 12cc ...................................(PL 3564) ..................... 22 Skirting Element RH .....................................(PL 4712) ..................... 23 Skirting Element LH .....................................(PL 4713) ..................... 24 Articulation Skirting Element ......................(PL 4714) ..................... 25 Complete Closing ..........................................(PL 3542) ..................... 26 30.7" Cutting Element RH ...........................(PL 3552) ..................... 27 30.7" Cutting Element LH ...........................(PL 3602) ..................... 28 Blade Assy Long RH .....................................(PL 3540) ..................... 29 Blade Assy Long LH .....................................(PL 3543) ..................... 30 Motor Blade Assy Short RH ........................(PL 3541) ..................... 31 Motor Blade Assy Short LH ........................(PL 3555) ..................... 32 Motor Blade Hsg. Assy Short RH ...............(PL 3557) ..................... 33 Motor Blade Hsg. Assy Short LH ...............(PL 3559) ..................... 34 Blade Hsg. Assy Long RH............................(PL 3556) ..................... 35 Blade Hsg. Assy Long LH ............................(PL 3558) ..................... 36 Hydraulics ............................................................................. 37 - 43 Electric Control Handle ...............................(PL 4859) ..................... 37 Electric Control Handle ...............................(PL 4456) ..................... 38 Electric Control With Mono Lever ............(PL 5204) ..................... 39 Hydraulic Kit ..................................................(PL 4859) ..................... 40 Non Return Security Valve JIC ...................(PL 2986) ..................... 41 Cylinder DE 35 - 25 ......................................(PL 1604) ..................... 42 Electric System Wiring..................................(PL 5049) ..................... 43
1.1 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14 2.15 3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 4 4.1 4.2 4.3 4.4 4.5 4.6 4.7
1
INTRODUCTION
Congratulations on your selection of a Collard Vine Trimmer.
HISTORY The COLLARD family has been servicing grape growers for 5 generations. Andre Collard invented the first mechanical vine trimmer in 1962. Since that development COLLARD has made numerous improvements and continues to be the world leader in trimmers.
QUALITY CONTROL Every stage in the production process is controlled to guarantee superior quality. After final assembly, each machine is run through a detailed test where everything is checked rotation speed, operating pressure, hydraulic cylinders, flow rates, etc. All this is done to insure that every machine leaving the factory is in perfect working order.
1.1
OPERATOR'S RESPONSIBILITY
Safe, efficient and trouble free operation of your Vine Trimmer requires that you and anyone else who will be operating or maintaining the machine, read and understand the Safety, Installation, Operation, Maintenance, and Troubleshooting information contained within the Operator's Manual. Keep this manual handy for frequent reference and to pass on to new operators or owners. Call your tractor dealer if you need assistance, information or additional copies of the manuals. OPERATOR ORIENTATION - The directions left, right, front and rear, as mentioned throughout this manual, are as seen from the driver's seat and facing in the direction of travel.
NAME: ____________________________________ PURCHASED FROM: ____________________________ DATE OF PURCHASE: ___________________________ CODE NUMBER: _______________________________ SERIAL NUMBER: ______________________________
1
2 SPARE PARTS - FRAMES 2.1
REINFORCED FRAME - CODE 0113 2001
PL 4049
2 1/2 Rows reinforced frame, independent height adjustment. Width adjustment stroke - 600mm
REF # QTY. 1 2 3 4 5 6 7 8 9 10 11 12 13
2
1 1 1 1 1 1 1 1 2 1 2 2 1
PART NO.
DESCRIPTION
01131952 01132002 01132006 01131958 00006280 00001476 04017109 00040900 01050207 00523321 01050179 04017114 00523325
Complete Vertical Double Frame Horizontal Large Frame RH Horizontal Large Frame LH Hydraulic Block with Protection Storage Support Large Lower Fixing Top Fixing Braces Complete Adjustable Vertical Support Complete Higher Arm RH Complete Higher Support Retractable Arm Complete Higher Arm LH
ASSY. PL 4050 - Pg 3 PL 4051 - Pg 4 PL 4052 - Pg 5 PL 4053 - Pg 6 PL 2262 - Pg 7 PL 3190 - Pg 8 PL 2261 - Pg 9 PL 3601 - Pg 10 PL 2253 - Pg 11 PL 3601 - Pg 10 PL 3179 - Pg 12 PL 2253 - Pg 11
2 SPARE PARTS - FRAMES 2.2 COMPLETE VERTICAL DOUBLE FRAME - CODE 0113 1952
REF #
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
1 1 1 4 2 4 2 2 4 16 16 16 2 2 2 2 2
PART NO.
DESCRIPTION
01131953 01131954 01131956 05011205 05016220 05015324 05014050 00528325 05014318 05014309 05010814 05011208 00201341 05014307 05010024 01131957 00002176
Fremale Double Frame Male Frame Male Frame Nut H M18 Zn Spindle Ø14 x 90 Washer W 18 Zn Bolt Pin Ø6 Zn Axle For Cylinder Washer Self Locking Ø12 Plastic Plug Ø16 Screw M20 Nut Hu M20 Zn Screw Lock Nut M16 Screw TH M10 x 25 Frame Back Stay Hyd. Kit - Cyl. 0501 9951 - Stroke=1000
PL 4050
ASSY.
PL 4859 Pg 40
3
2 SPARE PARTS - FRAMES 2.3 HORIZONTAL LG. FRAME RH - CODE 0113 2002
PL 4051
With Cylinder Stroke - 600 mm
REF #
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
1 1 1 1 1 1 1 1 1 3 3 1 2 1 1 1 1 1 1
4
PART NO.
DESCRIPTION
01132003 01132004 01131366 01131358 01131359 05011877 00480440 00480422 05011202 05010814 05011208 05014316 05014317 01130166 05019993 05010800 05010802 00201341 05014307
Female Tube Male Tube Cover Plate Axle Lg. 700 mm Axle Lg. 60 mm Screw Tensilok M8 x 16 Roller Steel With Ring Axle Nut H M 14 Screw M20 Nut Hu M 20 Zn Plastic Plug Ø16 - 13 mm Plastic Plug Ø16 ep 22 Support For Cross Slope RH Cylinder DE 35-18 Stroke = 600mm Screw Hc M6 x 12 Screw Hc M10 x 15 Screw Lock Nut M16
ASSY.
PL 3753 - Pg 15 PL 3754 - Pg 16
2 SPARE PARTS - FRAMES 2.4
HORIZONTAL LG. FRAME LH - CODE 0113 2006
PL 4052
With Cylinder Stroke - 600 mm
REF #
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
1 1 1 1 1 1 1 1 1 3 3 1 2 1 1 1 1 1 1
PART NO.
DESCRIPTION
01132003 01132007 01131366 01131358 01131359 05011877 00480440 00480422 05011202 05010814 05011208 05014316 05014317 01130170 05019993 05010800 05010802 05014307 00201341
Female Tube Male Tube Cover Plate Axle Lg. 700 mm Axle Lg. 60 mm Screw Tensilok M8 x 16 Roller Steel With Ring Axle Nut H M 14 Screw M20 Nut Hu M 20 Zn Plastic Plug Ø16 - 13 mm Plastic Plug Ø16 ep 22 Support For Cross Slope LH Cylinder DE 35-18 Stroke = 500mm Screw Hc M6 x 12 Screw Hc M10 x 15 Lock Nut M16 Screw
ASSY.
PL 3755 - Pg 14 PL 3754 - Pg 16
5
2 SPARE PARTS - FRAMES 2.5
HYDRAULIC BLOCK W/PROTECTION - CODE 0113 1958
REF #
QTY.
1 2 3 4 5 6 6
1 1 2 1 4 1 1
6
PART NO.
DESCRIPTION
04017105 05048580 00770113 04017107 05011877 0502 2937 0502 2939
Distributor Support Male Plug Protection Support Protection Screw Tensilok M8 x 16 Hydraulic Block With Electric Control - 4 DE Hydraulic Block With Electric Control - 6 DE
PL 4053
2 SPARE PARTS - FRAMES 2.6
LOWER FIXING - CODE 0000 1476
REF #
QTY.
1 2 3 4 5 6
1 2 4 2 2 2
PART NO.
DESCRIPTION
00200470 05029511 05010038 05010043 05011200 05015315
Large Fixation Front Mounting Back Stay Screw H M14 x 30 Screw M20 x 50 Zn Nut H M 20 Zn Washer W 20
PL 2262
7
2 SPARE PARTS - FRAMES 2.7
TOP FIXING - CODE 0401 7109
REF #
QTY.
PART NO.
DESCRIPTION
1 2 3 4 5 6 7 8
1 2 1 1 4 4 1 1
00040951 00040852 00040854 00040855 05015313 05011207 04017110 04017110-BIS
Central Latch Sliding Fastener Flat Left Flat Washer W 10 Zn Nut H M10 Zn Round Round
8
PL 3190
2 SPARE PARTS - FRAMES 2.8
BRACES - CODE 0004 0900
REF #
QTY.
1 2 3 4 5 6 7 8 9
2 2 2 2 2 2 2 2 2
PART NO.
DESCRIPTION
00040516 00040515 05010042 05015009 05015316 05011203 05010014 05015315 05011200
Tube Tube Screw H M12 x 50 Washer M12 Zn Washer W 12 Nut Hu 12 Zn Screw TH M20 x 60 Washer W 20 Nut M20 Hu
PL 2261
9
2 SPARE PARTS - FRAMES 2.9
LATERAL SUPPORT - CODE 0105 0207
REF #
QTY.
1 2 3 4 5 6 7 8 9 10 11
1 2 1 1 1 1 3 3 3 2 2
PART NO.
DESCRIPTION
05029543 05010007 05010942 05011954 01050206 01050208 05015009 05015316 05010006 05010024 05011207
Attachment Wedge Screw TH M12 x 20 Zn Schrew CHC M6 x 35 Compressing Spring Flange Adjustable Support - Vertical Element Washer M12 Washer W12 Screw TH M12 x 25 Screw TH M10 x 25 Nut M10 Hu
TOP SUPPORT - CODE 0105 0179
REF #
QTY.
1 2 3 4 5
1 1 2 1 1
10
PART NO.
DESCRIPTION
01050119 05029543 05010007 05010942 05011954
Top Support Attachment Wedge Screw TH M12 x 20 Zn Screw CHC M6 x 35 Compressing Spring
PL 3601
2 SPARE PARTS - FRAMES 2.10
LEFT TOP ARM - CODE 0052 3325
REF #
QTY.
1 2 3 4 5 6 7 8
1 1 2 1 1 1 1 1
PART NO.
DESCRIPTION
00523324 05014112 05015022 05015315 05010043 05010013 05014306 05017869
Top Arm Pin V 6 x 70 Washer M 20 Zn Washer W 20 Screw TH M20 x 50 Zn Screw TH M20 x 90 Zn Self Braked Nut M8 Tap For Square Tube 50 x 50 x 5
PL 2253
RIGHT TOP ARM - CODE 0052 3321
REF #
QTY.
1 2 3 4 5 6 7 8
1 1 2 1 1 1 1 1
PART NO.
DESCRIPTION
00523303 05014112 05015022 05015315 05010043 05010013 05014306 05017869
Top Arm Pin V 6 x 70 Washer M 20 Zn Washer W 20 Screw TH M20 x 50 Zn Screw TH M20 x 90 Zn Self Braked Nut M8 Tap For Square Tube 50 x 50 x 5
11
2 SPARE PARTS - FRAMES 2.11
RETRACTABLE ARM - CODE 0401 7114
REF #
QTY.
1 2 3 4 5 6
1 1 1 1 1 1
12
PART NO.
DESCRIPTION
04017115 00480020 05011966 05014081 05011973 05014112
Vertical Retractable Arm Tube Ø45 x 28 Compression Spring Elastic Bolt Spin Ø12 x 50 mm Compression Spring Pin V 6 x 70
PL 3179
2 SPARE PARTS - FRAMES 2.12
COMPLETE ANGLE BRAKE ASSY - CODE 0500 9030
REF #
QTY.
PART NO.
PL 0671
DESCRIPTION
1 1 05009051 Angle 2 1 05011204 Nut M8 3 1 05010826 Screw STHC M8 x 25 4 2 05002009 Joint Ø8.2 x 11.2 x 1 5 1 05011206 Nut M8 Hu Adjustment of oil flow on cylinder by angle brake
REF # 1 2 3
QTY.
PART NO.
DESCRIPTION
1 05010814 Screw M20 1 05011208 Nut Hu M20 Zn 1 05014315 Plastic Plug Ø16 1 05014309 Plastic Plug Ø17 1 05014314 Plastic Plug Ø18 Adjustment of play on sliding tube
DIMENSION A
4 mm 8 mm 16 mm
13
2 SPARE PARTS - FRAMES 2.13 SUPPORT FOR CROSS SLOPE LH - CODE 0113 0170
REF #
QTY.
PART NO.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12
1 1 1 1 1 1 1 1 1 2 1 1
00201324 01130161 05011851 05015022 05014301 00201319 BIS 05014305 05010056 05014311 00201327 05010001 05014307
Support For Anti-Shock Arm LH Axle Screw Tensilok M6 x 12 Zn Washer M20 Zn Self Braking Nut M20 Plate Brake Nut M14 Screw TH M10 x 100 Zn Nut M 10 Holding Washer Screw TH M16 x 90 Zn Lock Nut M16
14
PL 3755
2 SPARE PARTS - FRAMES 2.14 SUPPORT FOR CROSS SLOPE RH - CODE 0113 0166
REF #
QTY.
PART NO.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12
1 1 2 1 1 1 1 1 1 1 1 1
00201324 BIS 01130161 00201327 05014311 00201319 BIS 05010056 05015022 05011851 05014305 05010001 05014307 05014301
Support For Anti-Shock Arm RH Axle Holding Washer Nut M 10 Plate Screw TH M10 x 100 Zn Washer M20 Zn Screw Tensilok M6 x 12 Zn Brake Nut M14 Screw TH M16 x 90 Zn Lock Nut M16 Self Braking Nut M20
PL 3753
15
2 SPARE PARTS - FRAMES 2.15 DOUBLE EFFECT CYLINDER Ø35 - 18
REF #
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
PART NO.
DESCRIPTION
Corps-Body Ø35 Tie-Rod D18 05001307 05000043 05019005 05001002 05014300 05019670 05000041 05001301 05019671 05019004 05019983 05008669 05009030
Body (See Table Below) Rod (See Table Below) O-Ring Joint Threaded Base Joint Brake Nut M12 Half Piston Piston Joint O-Ring R 10 Flask Flange Fork Plug 12 x 17 Angle Elbow
Dimensions in mm: Cylinder: Rod: 0501 9993 0501 9483 - Set of Seals: 0501 9678
16
PL 3754
Body: 0501 9994
ØA 45
ASSY.
B 674
L 710
ØD 18
Stroke: 600
3 SPARE PARTS - ELEMENTS 3.1 DOUBLE FRAME ELEMENTS
REF #
QTY.
7 8 9 10 11 12
1 1 1 1 1 1
PART NO.
DESCRIPTION
00001906 00001905 00001881 00001890 00002361 00002360
51" LH 3 Blade Cut. Element 51" RH 3 Blade Cut. Element 30.7" LH 2 Blade Cut. Element 30.7" RH 2 Blade Cut. Element LH Skirt, Motor Driven RH Skirt, Motor Driven
PL 4870a
ASSY. PL 3688 - Pg 20 PL 3686 - Pg 18 PL 3602 - Pg 28 PL 3552 - Pg 27 PL 4713 - Pg 24 PL 4712 - Pg 23
17
3 SPARE PARTS - ELEMENTS 3.2 51" CUTTING ELEMENT - CODE 0000 1905
PL 3686
Cutting Height - 51" 12 cc Motor Position 2 RH Rotation
REF #
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13
1 1 1 1 2 1 1 2 2 1 6 1 4
18
PART NO.
DESCRIPTION
ASSY.
0105 0132 01050046 01050048 01221200 01050130 01050018 01050019 01050077 05028597 05016072 05011877 00420016 05011876
Motor 12 cc Aluminum Section 800 mm Aluminum Section 400 mm Leading Edge 1200 mm Blade Assy Long RH Complete Closing With Screws Complete Closing With Screws Junction L=150 mm Belt S 250 17 x 1039 mm Adhesive Sticker Screw Tensilock M8 x 16 Junction L=200 mm Screw Tensilok M8 x 25 Zn
PL 3564 - Pg 22
PL 3540 - Pg 29 PL 3542 - Pg 26 PL 3542 - Pg 26
3 SPARE PARTS - ELEMENTS 3.2
51" CUTTING ELEMENT - CODE 0000 1905 (CONTINUED)
REF #
QTY.
14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
10 1 1 1 1 1 1 1 14 1 2 5 7 7 3
PART NO.
DESCRIPTION
05017891 01050008 01050009 01050097 01050099 01050090 01050093 01050094 05010537 01050124 05010152 05010020 05015318 05011234 05030169
Plastic Obturator Case Reinforcement w/Screws LH Case Reinforcement w/Screws RH Blade Case 400 mm Blade Case 800 mm Cover 130 mm Cover 400 mm Cover 530 mm Screw FHC M6 x 12 Motor Blade Assy Short RH Screw TH M6 x 16 Screw TH M6 x 10 Washer W6 Nut M6 S. S. Blade 480 mm EL RH
PL 3686
ASSY.
PL 3541 - Pg 31
SPECIAL NOTE: With every stainless steel blade ordered it is recommended that the following also be ordered: 1 ea. 0503-0069
Mounting hardware for 1 blade consisting of:
1 ea. 0501 4311 1 ea. 0501 7926 2 ea. 0501 1861
Locknut M10 Plug Screw Tensilok M8 x 12
19
3 SPARE PARTS - ELEMENTS 3.3
51" CUTTING ELEMENT - CODE 0000 1906
PL 3688
Cutting Height - 51" 12 cc Motor Position 2 LH Rotation
REF #
QTY.
1 2 3 4 5 6 7 8 9 10 11
1 1 1 1 2 1 1 2 2 1 6
20
PART NO.
DESCRIPTION
0105 0132 01050046 01050048 01221200 01050129 01050018 01050019 01050077 05028597 05016072 05011877
Motor 12cc Aluminum Section 800 mm Aluminum Section 400 mm Leading Edge 1200 mm Blade Assy Long LH Complete Closing With Screws Complete Closing With Screws Junction L=150 mm Belt S 250 17 x 1039 mm Adhesive Sticker Screw Tensilock M8 x 16
ASSY. PL 3564 - Pg 22
PL 3543 - Pg 30 PL 3542 - Pg 26 PL 3542 - Pg 26
3 SPARE PARTS - ELEMENTS 3.3
51" CUTTING ELEMENT - CODE 0000 1906 (CONTINUED)
REF #
QTY.
12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
1 4 10 1 1 1 1 1 1 1 14 1 2 5 7 7 3
PART NO.
DESCRIPTION
00420016 05011876 05017891 01050008 01050009 01050097 01050099 01050090 01050093 01050094 05010537 01050123 05010152 05010020 05015318 05011234 05030170
Junction L=200 mm Screw Tensilok M8 x 25 Zn Plastic Obturator Case Reinforcement w/Screws LH Case Reinforcement w/Screws RH Blade Case 400 mm Blade Case 800 mm Cover 130 mm Cover 400 mm Cover 530 mm Screw FHC M6 x 12 Motor Blade Assy Short LH Screw TH M6 x 16 Screw TH M6 x 10 Washer W6 Nut M6 S. S. Blade 480 mm EL LH
PL 3688
ASSY.
PL 3555 - Pg32
SPECIAL NOTE: With every stainless steel blade ordered it is recommended that the following also be ordered: 1 ea. 0503-0069
Mounting hardware for 1 blade consisting of:
1 ea. 0501 4311 1 ea. 0501 7926 2 ea. 0501 1861
Locknut M10 Plug Screw Tensilok M8 x 12
21
3 SPARE PARTS - ELEMENTS 3.4
HYDRAULIC MOTOR 12CC - CODE 0105 0132
REF #
QTY.
1 2 3 4 5 6 7 8 9
1 1 1 4 4 4 4 1 2
22
PL 3564
PART NO.
DESCRIPTION
01050039 01050021 01050024 05015317 05010903 05011659 05011215 05021061 05006578
Motor Plate Pinion With Cone Coupling Washer W8 Screw CHC M8 x 25 Gudgeon M6 x 25 Nut Tensilok M6 Zn Hydraulic Motor 12cc Angle MJ 3/4 - MG 1/2 Cyl. With Counter Nut
3 SPARE PARTS - ELEMENTS 3.5
REF # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SKIRTING ELEMENT RH - CODE 0000 2360
QTY. 2 2 2 5 1 1 1 1 1 1 1 1 1 8 1
PART NO.
DESCRIPTION
0105 0132 05010020 05015318 05011234 05017891 01050124 01050018 01050009 00940250 01050331 01050332 01220350 01050074 01050090 05010537 05030169
Motor 12cc Screw TH M6 x 10 Washer W 6 Nut M6 Plastic Obturator Motor Blade Assy. Short RH Complete Closing With Screws Case Reinforcement With Screws RH Articulation - Motor Skirting Element Aluminum Section 350 mm Blade Case 350mm - Skirting Element Leading Edge 350mm Cover 80mm Cover 130mm Screw FHC M6 x 12 S. S. Blade 480mm EL RH
PL 4712
ASSY. PL 3564 - Pg 22
PL 3541 - Pg 31 PL 3542 - Pg 26 PL 4714 - Pg 25
23
3 SPARE PARTS - ELEMENTS 3.6
SKIRTING ELEMENT LH - CODE 0000 2361
REF #
QTY.
PART NO.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
2 2 2 5 1 1 1 1 1 1 1 1 1 8 1
0105 0132 05010020 05015318 05011234 05017891 01050123 01050019 01050008 00940250 01050331-BIS 01050332-BIS 01220350 01050074 01050090 05010537 05030170
Motor 12cc Screw TH M6 x 10 Washer W 6 Nut M6 Plastic Obturator Motor Blade Assy. Short LH Complete Closing With Screws Case Reinforcement With Screws LH Articulation - Motor Skirting Element Aluminum Section 350 mm Blade Case 350mm - Skirting Element Leading Edge 350mm Cover 80mm Cover 130mm Screw FHC M6 x 12 S. S. Blade 480mm EL LH
24
PL 4713
ASSY. PL 3564 - Pg 22
PL 3555 - Pg 32 PL 3542 - Pg 26 PL 4714 - Pg 25
3 SPARE PARTS - ELEMENTS 3.7 ARTICULATION SKIRTING ELEMENT - CODE 0094 0250
REF #
QTY.
1 2 3 4 5 6 7 8 9 10 11
1 1 1 1 1 2 1 2 8 2 2
PART NO.
DESCRIPTION
00940248 00940249 00940229 00940211 05015009 05015025 05014300 00940251 05011877 05015313 05010024
Upper Element Lower Element Long Spacer Roller Axle Washer M12 Washer M10 Zn Locknut M12 Closing Element Screw Tensilok M8 x 16 Washer W 10 Screw TH M10 x 25
PL 4714
ASSY.
25
3 SPARE PARTS - ELEMENTS 3.8
COMPLETE CLOSING - CODE 0105 0018
REF #
QTY.
1 2 3 4 5 6 7
1 2 2 2 2 2 2
PART NO.
DESCRIPTION
01050017 01050015 05010501 05015318 05011851 05011234 05011877
Closing Link Part Screw FHC M8 x 15 Washer W6 Screw Tensilok M6 x 12 Zn Nut M6 Screw Tensilok M8 x 16
COMPLETE CLOSING (SYMMETRICAL) - CODE 0105 0019
REF #
QTY.
PART NO.
DESCRIPTION
1 2 3 4 5 6 7
1 2 2 2 2 2 2
01050017-BIS 01050015 05010501 05015318 05011851 05011234 05011877
Closing Link Part Screw FHC M8 x 15 Washer W6 Screw Tensilok M6 x 12 Zn Nut M6 Screw Tensilok M8 x 16
26
PL 3542
3 SPARE PARTS - ELEMENTS 3.9
30.7" CUTTING ELEMENT - CODE 0000 1890
PL 3552
Cutting Length - 30.7" 12 cc Motor RH Rotation
REF #
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1 1 1 1 1 1 1 1 1 1 8 1 1 2 1 6 4 4 4 2
PART NO.
DESCRIPTION
0105 0132 01050045 01050124 01050130 05028596 01050096 01050018 01050019 01050091 01050074 05010537 00420016 01220600 05011876 05016072 05017891 05010020 05015318 05011234 05030169
Motor 12 cc Aluminum Section 600 mm Motor Blade Assy Short RH Blade Assy Long RH Belt S 250 17 x 842 mm Blade Case 690 mm Complete Closing With Screws Complete Closing With Screws Cover 380 mm Cover 80 mm Screw FHC M6 x 12 Junction L=200 mm Leading Edge 600 mm Screw Tensilok M8 x 25 Zn Adhesive Sticker Plastic Obturator Screw TH M6 x 10 Washer W6 Nut M6 S.S. Blade 480 mm EL RH
ASSY. PL 3564 - Pg 22 PL 3541 - Pg 31 PL 3540 - Pg 29 PL 3542 - Pg 26 PL 3542 - Pg 26
27
3 SPARE PARTS - ELEMENTS 3.10 30.7" CUTTING ELEMENT - CODE 0000 1881
PL 3602
Cutting Length - 30.7" 12 cc Motor LH Rotation
REF #
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1 1 1 1 1 1 1 1 1 1 8 1 1 2 1 6 4 4 4 2
28
PART NO.
DESCRIPTION
0105 0132 01050045 01050123 01050129 05028596 01050096 01050018 01050019 01050091 01050074 05010537 00420016 01220600 05011876 05016072 05017891 05010020 05015318 05011234 05030170
Motor 12 cc Aluminum Section 600 mm Motor Blade Assy Short LH Blade Assy Long LH Belt S 250 17 x 842 mm Blade Case 690 mm Complete Closing With Screws Complete Closing With Screws Cover 380 mm Cover 80 mm Screw FHC M6 x 12 Junction L=200 mm Leading Edge 600 mm Screw Tensilok M8 x 25 Zn Adhesive Sticker Plastic Obturator Screw TH M6 x 10 Washer W6 Nut M6 S.S. Blade 480 mm EL LH
ASSY. PL 3564 - Pg 22 PL 3555 - Pg 32 PL 3543 - Pg 30 PL 3542 - Pg 26 PL 3542 - Pg 26
3 SPARE PARTS - ELEMENTS 3.11
BLADE ASSEMBLY LONG RH - CODE 0105 0130
REF #
QTY.
1 2 3 4 5 6 7
1 1 2 1 1 4 4
PART NO.
DESCRIPTION
01050072 01050031 05011861 05014311 05017926 05015318 05010905
Blade Hsg. Assy. Long RH Cup Screw Tensilok M8 x 12 Zn Locknut M10 Cap Ø26 mm Washer W6 Screw CHC M8 x 20
PL 3540
ASSY. PL 3556 - Pg 35
29
3 SPARE PARTS - ELEMENTS 3.12
BLADE ASSEMBLY LONG LH - CODE 0105 0129
REF #
QTY.
1 2 3 4 5 6 7
1 1 2 1 1 4 4
30
PART NO.
DESCRIPTION
01050071 01050031 05011861 05014311 05017926 05015317 05010902
Blade Hsg. Assy. Long LH Cup Screw Tensilok M8 x 12 Zn Locknut M10 Cap Ø26 mm Washer W8 Screw CHC M8 x 20
PL 3543
ASSY. PL 3558 - Pg 36
3 SPARE PARTS - ELEMENTS 3.13
MOTOR BLADE ASSY SHORT RH - CODE 0105 0124
REF #
QTY.
1 2 3 4 5 6 7
1 1 2 1 1 4 4
PART NO.
DESCRIPTION
01050066 01050031 05011861 05014311 05017926 05015318 05010902
Motor Blade Hsg. Assy. Short RH Cup Screw Tensilok M8 x 12 Zn Locknut M10 Cap Ø26 mm Washer W6 Screw CHC M8 x 20
PL 3541
ASSY. PL 3557 - Pg 33
31
3 SPARE PARTS - ELEMENTS 3.14
MOTOR BLADE ASSY SHORT LH - CODE 0105 0123
REF #
QTY.
1 2 3 4 5 6 7
1 1 2 1 1 4 4
32
PART NO.
DESCRIPTION
01050065 01050031 05011861 05014311 05017926 05015317 05010902
Motor Blade Hsg. Assy. Short LH Cup Screw Tensilok M8 x 12 Zn Locknut M10 Cap Ø26 mm Washer W8 Screw CHC M8 x 20
PL 3555
ASSY. PL 3559 - Pg 34
3 SPARE PARTS - ELEMENTS 3.15 MOTOR BLADE HSG. ASSY SHORT RH - CODE 0105 0068
REF #
QTY.
1 2 3 4 5
1 1 1 1 1
PART NO.
DESCRIPTION
05000038 01050064 01050056 01050023 01050022
Ring NILOS Blade Housing Short Shaft Motor, Blade RH Motor Pulley Threaded Nut On Right
PL 3557
ASSY.
33
3 SPARE PARTS - ELEMENTS 3.16 MOTOR BLADE HSG. ASSY SHORT LH - CODE 0105 0065
REF #
QTY.
1 2 3 4 5
1 1 1 1 1
34
PART NO.
DESCRIPTION
05000038 01050064 01050055 01050044 01050063
Ring NILOS Blade Housing Short Shaft Motor, Blade LH Motor Pulley Threaded Nut On Left
PL 3559
ASSY.
3 SPARE PARTS - ELEMENTS 3.17
BLADE HSG. ASSY. LONG RH - CODE 0105 0072
REF #
QTY.
1 2 3 4 5 6
1 1 1 1 1 1
PART NO.
DESCRIPTION
05000038 01050025 05005206 05005256 01050064 01050062
Ring NILOS Pulley Nut KM6 Washer MB6 Blade Housing Long Shaft Blade RH
PL 3556
ASSY.
35
3 SPARE PARTS - ELEMENTS 3.18
BLADE HSG. ASSY. LONG LH - CODE 0105 0071
REF #
QTY.
1 2 3 4 5 6
1 1 1 1 1 1
36
PART NO.
DESCRIPTION
05000038 01050025 05005206 05005256 01050064 01050061
Ring NILOS Pulley Nut KM6 Washer MB6 Blade Housing Long Shaft Blade LH
PL 3558
ASSY.
4
HYDRAULICS 4.1
ELECTRIC CONTROL HANDLE - CODE 0000 2340
PL 4859
For machines equipped with 1 to 8 double effect cylinders, without function of control for proportional valve Complete Electric Control Handle With Box, Wires and Female Plug:
Bundle of Wires and Male Plug (19 Connectors):
0506 0081
0506 1081
Support: 0502 9872
Connectors 1 to 8, 12 and 13: Double effect cylinder functions Connector 9: ON/OFF Motors Function Connector 10: By-pass Function Connector 11: EVC Function (only in case of closed center hydraulic systems which work with the additional hydraulic unit 0000 1561)
37
4
HYDRAULICS 4.2
ELECTRIC CONTROL HANDLE - CODE 0000 2340 Emergency stop and general ON/OFF function
PL 4456
Display Screen
Selection of the movements carried out by the hydraulic cylinders
ON/OFF Hydraulic motors
ON Signal of the hydraulic motors
Joystick: control of the movements of the hydraulic cylinders
To carry out a movement of a hydraulic cylinder, operate the joystick by tilting it towards one of the 4 directions following the desired cylinder movement. Functions are changed by pushing the button located in the center of the joystick. 1. First press the button in order to select the desired function. 2. Then tilt simultaneously the joystick (without releasing the button). NOTE: To carry out another movement it is necessary to bring the level to the central position (neutral position), then use steps 1 and 2 to obtain the next function (cylinder movement).
IMPORTANT:
38
In order to optimize the longevity of the control handle, after each use, keep the handle in a clean and dry place, devoid of dust and grease.
4
HYDRAULICS 4.3
ELECTRIC CONTROL WITH MONO LEVER FROM 1 TO 8 DE
PL 5204
39
4
HYDRAULICS
4.4
PL 4859
HYDRAULIC KIT - CODE 0000 2176
REF #
QTY.
1 2 3 4 5
1 1 1 1 1
40
PART NO.
DESCRIPTION
ASSY.
05019951 05009030 00001322J 05007750 05019703
Cylinder Ø35-25 Stroke: 1000mm PL 1604 - Pg 41 Angle Elbow PL 0671 - Pg 13 Non return Security Valve PL 2986 - Pg 40 Union Tube
4
HYDRAULICS
4.5 NON RETURN SECURITY VALVE JIC - CODE 0000 1322J
REF #
QTY.
1 2 3 4 5 6 7
1 2 1 1 1 1 1
PART NO.
DESCRIPTION
05023307 05002006 05007767 05006006 05006577 05006420 05007816
Double Valve Joint Junction Adapter Elbow MJ 9/16 - MG 1/4 90° Elbow MJ 9/16 FJ 9/16 90° Junction MJ 9/16 MG 8/13
PL 2986
ASSY.
41
4
HYDRAULICS 4.6
REF #
QTY.
1 2 3 4 5 6 7 8 9 10 11 12
1 1 1 1 1 1 1 1 1 1 1 1
PART NO.
DESCRIPTION
05019189 05019463 05001307 05000042 05019117 05001004 05014300 05019670 05000041 05001301 05019671 05005319
Body (See Table Below) Rod (See Table Below) O-Ring Rod Joint Ø25 Threaded Base Top Rod Joint Ø25 Brake Nut M12 Half Piston Piston Joint O-Ring R 10 Flask Spacing Ring
Dimensions in mm: Cylinder: Rod: 0501 9247 0501 9248 - Set of Seals: 0501 9679
42
PL 1604
CYLINDER DE 35 - 25 - CODE 0501 9247
Body: 0501 9249
ØA 45
B 874
L 945
ØD 25
Stroke: 800
4
HYDRAULICS 4.7
ELECTRIC SYSTEM WIRING
PL 5049
43
