Transcript
A Scrapping, Pre-flushing and Food Waste Collecting System
2 3 5 6 7 8
Table Installation and Location Typical Installations Plumbing Electrical Operating Instructions Warranty
ALL INSTALLATIONS SHOULD BE MADE IN ACCORDANCE WITH LOCAL AND NATIONAL PLUMBING AND ELECTRICAL CODES.
The Salvajor Company
Installation Instructions
Salvajor P914 Pot/Pan Collector
4530 East 75th Terrace Kansas City, Missouri 64132-2081, USA 1- 888- SALVAJOR FAX: 1 - 800 - 832 - 9373 www.salvajor.com Email:
[email protected] [email protected] Manufacturers of Commercial Food Waste Disposing Systems since 1944
Table Installation and Location The P914 Pot/Pan Collector is designed primarily for use in a pot and pan area in conjunction with a three-compartment sink.
The system can also be used in a dish room, adjacent to a dishmachine. In that case, locate the unit at least 24” away from the loading end of the dishmachine to allow ample space for dish racks.
The Pot/Pan Collector is furnished with a template for making the proper cut-out in the dishtable for installation. Once the location of the Collector has been determined, place the template in position on the tabletop and mark the opening to be cut.
Make certain that the gusher tube inside the Collector is positioned on the side closest to the dishmachine or sink. The flow of the water plume from the gusher tube must angle up and away from the dishmachine or sink. The unit is now ready for installation.
R10" (R25.40)
20" (50.80)
TABLE CUTOUT 22 7/8" (58.16) 32 7/8" (83.56)
Collectors are most commonly welded to the dishtable. However, they are furnished with the mounting flanges punched for either bolting or studweld bolting to the table.
2
Typical Installations
DISHRACK
DISHRACK
3
Typical Installations PASS THRU WINDOW
PASS THRU WINDOW
4
Plumbing 1. WATER SUPPLY The Salvajor Pot/Pan Collector is designed for easy plumbing installation. The solenoid valves are factory installed and are attached to an automatic water blender which will introduce water tempered to approximately 107˚ F.
Plumb 3/4" lines from both hot and cold water supply sources and reduce to 1/2" before attaching to corresponding valves on the Collector water harness.
AIR GAP
SOLENOID WATER BLENDER CHECK VALVES HOT/COLD SHUTOFF VALVES 1/2" NPT INCOMING WATER 2" NPT DRAIN
IMPORTANT: The Pot/Pan Collector is equipped with an approved air gap, eliminating the need for vacuum breakers.
NOTE: To assure against leaks, tighten water harness fittings. They may come loose during shipment, fabrication or installation. Pressure regulators should be installed in areas where water pressure exceeds the recommended maximum of 80 psi.
2. DRAIN PIPING Plumb a 2" pipe from the 2" male threaded nipple located on the bottom of the Collector reservoir tank to the nearest approved drain. The drain line should have a minimum of 1/4"
slope of fall per running foot. It is the responsibility of the plumbing contractor to check all connections to ensure they are free of leaks.
MAKE ALL PLUMBING CONNECTIONS IN ACCORDANCE WITH NATIONAL AND LOCAL PLUMBING CODES.
5
Electrical The wiring diagram for electrical connections is located in the terminal strip box mounted on the side of the Collector above the motor. A secondary diagram is located within the control panel furnished with the unit. The motor and solenoid valve furnished with the unit are factory prewired to the terminal strip box.
shown on the wiring diagram and wiring from the power source to the control panel. The Pot/Pan Collector is supplied with a Salvajor Model SS-33 control panel which will control the Collector motor and solenoid valve. The motor is protected by automatic internal overloads. The enclosure for the Model SS-33 control is stainless steel, NEMA 4X watertight rated and UL listed.
Field wiring will consist of wiring from the terminal strip box to the control panel as
OUT TO SYSTEM 1/2" CONDUIT
IN FROM CONTROL PANEL 1/2" CONDUIT
INCOMING POWER 1/2" CONDUIT
TOTAL FULL LOAD AMPS PHASE 115V
208V
230V 460-480V
1PH
11
5.5
5.5
---
3PH
---
3.2
3
1.5
NOTE: Always use watertight conduit and fittings when wiring this product.
MAKE ALL INSTALLATIONS IN ACCORDANCE WITH LOCAL AND NATIONAL ELECTRICAL CODES.
STOP! If you have any questions about this installation call 1- 888 - SALVAJOR for installation advice.
6
Operating Instructions TO START:
TO STOP:
1 Place OVERFLOW PIPE into drain ●
A Press STOP button on the CONTROL ●
2 Position SCRAP BASKET inside tank. ● 3 Position SALVAGE BASIN inside tank ●
B Check for and remove dropped tableware ●
opening in bottom of tank (center hole).
PANEL.
trapped in SALVAGE BASIN.
C Remove and drain SALVAGE BASIN. ● D Remove SCRAP BASKET and dump ●
over SCRAP BASKET.
4 Press START button on CONTROL ●
PANEL. Allow time for reservoir tank to fill and the water plume to remain at a constant height.
● 5
waste into trash receptacle.
E Remove OVERFLOW PIPE to drain tank. ●
Rinse SALVAGE BASIN, SCRAP BASKET, OVERFLOW PIPE, and tank interior thoroughly.
Adjust WATER PLUME VALVE. Recommended plume height 4-6”.
7
Salvajor Warranty ONE YEAR PARTS AND LABOR
Equipment covered by this warranty:
Conditions not covered by this warranty:
All Salvajor commercial disposers and disposing systems.
Faulty or improper electrical installations, faulty or improper plumbing installations, disposer jammed by foreign object, tripped overload (re-set button), clogged drains, pump jams, clogged solenoid valves, abuse, accidental damage, unit improperly sized for application according to factory recommendations.
Length of this warranty: Parts and labor for one year from date of installation or 15 months from date of shipment from the factory, whichever occurs first. Accessories are covered when they are sold as part of the original disposer assembly or system package.
This warranty is limited to the continental United States, Hawaii and Canada.
For your nearest Factory Authorized Service Center:
Warranty coverage: Providing the equipment is unaltered, has been properly installed, maintained and operated, Salvajor will repair or replace at no cost, defective parts due to material or workmanship, if such service is performed by a Salvajor Authorized Service Center. Parts wear is not considered a defect.
Call 1- 888 - SALVAJOR or 816 - 363 - 1030 Fax 1- 800 - 832 - 9373 or 816 - 363 - 4914
The Salvajor Company 1- 888- SALVAJOR www.salvajor.com
4530 East 75th Terrace Kansas City, Missouri 64132-2081, USA (816) 363 - 1030 FAX: 1 - 800 - 832 - 9373 Email:
[email protected] [email protected]
Manufacturers of Commercial Food Waste Disposing Systems since 1944
8
Printed in USA Form No. II-P914-1
